Temperature Control
Express Extractor Heater 3.5 to 11KW of heating Power!
Express Extractor Heater by BVV™ 1 Year Warranty, Built in house ready to ship in 24hrs! The BVV™ Extractor Heater is our built in house high power extractor heater circulator. We have 3 model units 3,500, 8,000 & 11,000 WATTS! Each upright panel comes with 25ft of silicone tubing and a 5 gallon reservoir. Each system is capable of heating up to 140°F and can exceed the demand of even the largest extraction vessels. The system operates on an independent nitrile diaphragm pump circulating water @1.5GPM. The pump can self prime up to 11ft. and within a typical extractor this pump is operating around 30-50psi in circulating pressure. BVV Part# KW AMPS Voltage Breaker AMPS Installed Plug Rec. Wire Size Temp. Range EEH-3.5KW 3.5 29 120V (1x30)A L5-30P Plug 10 AWG 120°F EEH-8KW 7.3 33 240V (1x40)A 6-50P 8 AWG 80-140°F (adjustable) EEH-11KW 11 46 240V (2x30)A 6-30P (2x12) AWG 80-140°F (adjustable) EEH-5.5KW 5.5 25 220V (1X25)A 6-30P 10 AWG The 3.5KW unit has a digital temperature display and cannot be adjusted from the standard factory programmed 120°F. During normal recovery operations used with our extractors this fluctuates between 120-157°F. Though there is a lack in temperature accuracy we measure at the extractor base a consistent recovery temperature around 122-125°F. These heater are built with an electrical failsafe that prevents them from operating dry, and will auto shut down if the flow is unexpectedly stopped to protect the unit. The attached in-line filter will prevent any debris from entering the heater. A clogged filter will also prevent the heater from operating. General Extractor Size Heater Recommendations for these Models 0-2lbs Biomass EEH-3.5KW 2-5lbs Biomass EEH-8KW 5-20lbs Biomass EEH-11KW At BVV our favorite model is the 11KW. The unit does require two 240V 30A Single phase circuits, but its now a permanent fixture in or laboratory. Every model will pump out lots of heat for any recovery situation, could you use a 3.5KW heater on a 5 or 10lb unit? Absolutely, Just expect longer times to reach the heaters maximum setting. For example we heated 3x 6"x48" fully jacketed columns to 140°F (heater temp) in about 11 minutes using the 11KW heater. Another example is a 1lb Apollo extractor with a fully jacketed collection base heated to 120°F in about 8-9 min. using the 3.5KW extractor heater. ETL Listed to UL 499 and CSA (Canada) Utilizing all UL approved components for the heater, pump, and emergency stop switches, wiring harnesses, plugs, and electrical housings. The heater arrive with the specified plugs attached, however all of the models can be hardwired directly if you choose not to use a plug. *240V units can be used on 208V single phase with 25% reduced temperature output Express Extractor Heater Quick Start Guide
$1,075.00 - $1,375.00
Hubbell Process Water Heater 240V 3P
Hubbell Process Water Heater 240V 3P Process Water Heater -6 Gallon Stainless Steel ASME Vessel -36 kW, 240 volt, 3 phase - Option N - Stainless Steel Flanged Mounting Legs Packaged Hubbell electric heater with a 304 stainless steel vessel ASME Section VIII stamped. Complete with electrical operating controls including the following: magnetic contactor, immersion elements, digital temperature controller with safety hi-temperature cut out, low water cut out, and an ASME rated combination temperature and pressure relief valve. Unit is factory assembled, insulated, jacketed, wired, and tested. Unit is ready for electrical and plumbing service connections. This kit includes a Taco pump to continuously circulate water through a closed loop system, an expansion chamber may be needed. Professional installation of water lines by a certified plumber is recommended. Water Heater Features Industrial Grade Construction Stainless steel pressure vessel provides maximum service life ASME Section VIII stamped vessel ensures high quality construction Heavy duty construction withstands demanding industrial use Packaged with all electrical operating controls for efficient installation Small reserve capacity lowers peak power demand and reduces operating costs in systems with ON / OFF cyclical demand Pump Operating Modes: Auto mode (default) Proportional pressure control Constant pressure control Constant speed Night setback turndown Pump Features High-efficiency ECM motor uses up to 85% less electricity LED displays watts, flow & RPM Compact size for easy handling and installation Plug & play simplicity Robust construction for long life Industry standard flange configuration and lay length Low noise operation 1" FNPT adapters are included Hubbell V636T Heater Specs Model V636T Voltage 240V Current Draw (A) 87 Heating Wattage (kW) 36 Storage Capacity (Gal) 6 Inlet / Outlet Connections 3/4" MNPT Taco VR3452 Pump Specs RPM 1100 - 4400 Material Cast Iron Horsepower 1/100 - 1/4 Max Pressure (PSI) 145 Max Head (Ft.) 34 Max Flow (GPM) 52 Flow Range (GPM) 0-52 Current Draw (A) 2.5 Voltage 115
$6,600.00
Neocision 20L Chiller (-40c) - ETL Rated
NEOCISION 20L Chiller (-40c) - ETL Rated Product Name Circulating Chiller Model NEO20L-40 Reservoir volume L) 20L Refrigeration performance No-load minimum temperature (℃) A: ﹣ 20℃ ( Customizable: ﹣ 30℃ / C: ﹣ 40℃ Best operating temperature (℃) A: ﹣ 20℃ ~ 20℃B: ﹣ 30℃ ~ 20℃C: ﹣ 40℃ ~ 20℃ Best operating environment (℃) ≤30 Environmental relative humidity (%RH) ≤65 Cooling capacity at -40 ℃ kw 0.7 Refrigerant R404A Electrical performance Cooling unit power (W) 1500 Sensor pt100 Controller, monitor liquid crystal Computer interface R485 optional safety protection Compressor delay protection, machine leakage,over-current, over-voltage protection Power AC230V±10%/60HZ Pump Power (W) 15 Maximum flow (L/min) 10 Maximum lift (m) 2.5 Liquid inlet and outlet pipe diameter (mm) φ18 Whole machinefunction Total Weight (Kg) 105 Tank opening/depth ( mm) φ300mm*300mm Out size (mm) 420*580*790 Adaptation rotary evaporator (volume* number) 10L*2 Note The equipment can be customized to different supply voltage frequency; different flow head external circulation system and external magnetic stirring device. TEMP: Displays the measured temperature value. To set the desired temperature, press the setting key until the TEMP SET value flashes. Press the setting key again to confirm the parameter. SET: Displays the desired temperature value set manually. RUN: Indicates that the chiller is operating. Cooling Indicator: Appears when the chiller is cooling. Circulation Indicator: Appears when the pump is operating. TIME: Displays the set running time; this value countdowns to zero and operation stops. To set a timer, press the setting key. When the TIME value flashes, enter the desired time using they arrow keys. Leave at zero if a timer is not needed. Silence Indicator: Appears when an alarm has been silenced. Alarm Indicator: It will appear when there is an alarm. Settings: Used for manually setting values and parameters. Left Arrow: Shifts to the numbers on the left to set desired value. Down Arrow: One push will decrease 1 digit; A long press will decrease digits faster. Up Arrow: One push will increase 1 digit; A long press will increase digits faster. Cooling Key: Press and hold key for more than 4 seconds to control start/stop the cooling function. Circulation Key: Press to start/stop the circulation function. Note: After all parameters have been input, press the cooling key for four seconds to being operation. Instructions Before Use The unit should be used under the following conditions: Place on a stable, non-combustible flat surface Ambient temperature of 5 ~ 35 ℃ Relative humidity ≤ 85% Atmospheric pressure: (86 ~ 106) KPa Altitude not higher than 2000 meters Power: 5L AC 110V±10%/60HZ, 20L: AC230V±10%/60HZ Keep away from any heat, corrosive gasses, strong vibration and electromagnetic sources. Provide a minimum of 300mm of space for proper ventilation (front and rear) Do not spill liquid anywhere other than the bath. When setting temperatures pay attention to freezing points (ethanol/ethylene glycol). When operating for the first time after replacing the heat transfer fluid there may be air trapped in the circulating pump, follow these instructions to purge: a. Disconnect the outlet line from the application NOTE: Fluid may leak from application, be ready with a bucket or plug the port. Hold the Outlet hose above the top of the bath so fluid does not drain out. b. Place the outlet hose into a clean collection bucket. c. Hold the outlet hose firmly so it does not fall out of the collection bucket d. Wearing safety glasses to shield any splashes, turn on the circulating function. e. After the liquid flow significantly increases, turn off the circulator. f. Reconnect the hoses to your application’s ports.
$4,850.00
BVV -80C Chiller - 220v/60hz
BVV -80C Chiller - 220v/60hz This recirculating chiller is great for low temperature applications. With the a powerful pump it is able to circulate fluid while at -80°C. The chiller includes valves for the inlet and outlet port with 3/4" FNPT connections. The chiller also includes two barbs to adapt to 5/8" tubing, along with 2M of insulated silicone tubing. Technical Data 3 Phase Single Phase Reservoir: 10L 10L Flow: 35L/min 35L/min Lift: 12m 12m Refrigerant: R404/R23 R404/R23 Low Temperature: -80℃ -80℃ Cooling capacity: 8048~1260W 7665~1200W @30°C 8048W 7665W @0°C 6021W 5735W @-40°C 4326W 4120W @-80°C 1260W 1200W Max. Input Current: 17 amps 24 amps Power supply: 220V/60Hz/3Φ 220V/60Hz/1Φ Circulator Low-temperature CoolantCirculation Pump Low-temperature CoolantCirculation Pump
$12,750.00
NEOCISION Cold Trap with Pump - ETL Rated - (-40c)
NEOCISION Cold Trap with Pump - ETL Rated - (-40c) Looking for a cold trap and small application chiller? The BVV™ CT40 features a 2-in-1 use with a cold trap function and built in circulating system for small batch temperature control. Cold Trap Function Use the BVV™ CT40 to condense vapors down to -40°C before they reach your vacuum pump. This prolongs the life of the vacuum system, reduces the need to change oil frequently, and efficiently traps vapors otherwise lost to evaporation such as terpenes. Common applications include short path distillation, rotary evaporation, reactor setups, or any other application where volatile vapors can damage your vacuum pump. Chiller Function Use the BVV™ CT40 for small batch temperature control down to -40°C. Switch out the cold trap configuration with solid lid to turn your cold trap into a chiller. Common applications include condensing coils, small vessel setups, heat exchangers. Operating 2-in-1 Simultaneously Use the BVV™ CT40 as a cold trap and chiller. The unit can be used with the cold trap configuration and circulating function simultaneously. Commonly used as for chilling applications with no additional heat load. BVV™-CTC40-WP Power Requirement AC 110V +/- 10% / 60Hz Relative Humidity < 85% Cooling Capacity 400W Refrigerant R404A Cold Trap Capacity 3 x 300ml Cold Trap Barb Dia. 10mm Reservoir Capacity 6.8L External Dimensions 305 x 485 x 635mm Weight 149 lbs Call in to see how we can pair this unit with your setup Please Note: This device is designed for operation on its own independent circuit breaker. For best results, do not use this device on a breaker shared with other equipment. ***Notice to Customers: All units are inspected for broken glass or parts before the unit is shipped. If unit arrives damaged or glass is broken (this does not include minor imperfections or scuffs in glassware), Customer MUST contact BVV™ within 3 days of delivery to file a claim and receive a replacement part. If customer DOES NOT contact BVV™ within 3 days of delivery responsibility for replacement parts falls on the customer and they must pay for replacement pieces.*** ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***
$3,100.00
NEOCISION Cold Trap - ETL Rated - (-80c)
NEOCISION Cold Trap - ETL Rated - (-80c) The BVV™ CT80 Cold Trap is used to condense vapors lost in vacuum applications before they reach the vacuum system. This prolongs the life of the vacuum system, reduces the need to change oil frequently, and efficiently traps vapors otherwise lost to evaporation such as terpenes. The CT80 model reaches a maximum temp of -80°c or -112F under vacuum and contains three traps for maximum efficiency and condensation of vapors. Place in-line between application and your vacuum system. Specifications: Temp Range: -112F to Ambient Internal Dimensions: 180mm Internal Diameter x 210mm Depth (Holds about 1.4 gallons) External Dimensions: 505 x 620 x 750mm Weight: 149lbs Stainless Steel Interior 3x Pyrex Glass Traps 110V Power Please Note: This device is designed for operation on its own independent circuit breaker. For best results, do not use this device on a breaker shared with other equipment. ***Notice to Customers: All units are inspected for broken glass or parts before the unit is shipped. If unit arrives damaged or glass is broken (this does not include minor imperfections or scuffs in glassware), Customer MUST contact BVV™ within 3 days of delivery to file a claim and receive a replacement part. If customer DOES NOT contact BVV™ within 3 days of delivery responsibility for replacement parts falls on the customer and they must pay for replacement pieces.*** ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***
$6,400.00
BVV™ ULTRA-Low Chest Style Freezer (-86°C) 4.5 Cubic Feet
4.5 Cubic Feet Chest Freezer, Ultra Low Temperature The brand new BVV™ 4.5 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. It contains a dual independent refrigeration system inside and a SECOP compressor. This unit will run productively and efficiently, with a sleek design that will fit any lab or office setting. Every freezer unit includes various safety and protection features for both user and item safety. Features include high and low-temperature alerts and even a locking door. These compact chest freezers are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended for storage of pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. The freezer can fit up to two 5 gallon buckets inside. Key Features: 3 Ports to allow tubing or probes. SECOP Compressor Durable Powder Coated Exterior Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters Specifications Model Number BVV™-86C45 Voltage 115V / 60Hz Wattage 500w Capacity 128L / 33.8G Temperature Range -40°C to -86°C Exterior Dimensions 32.3" x 28" x 39.3" Interior Dimensions 25" x 17.5" x 18" Weight 197lbs
$4,950.00
BVV™ ULTRA-Low Chest Style Freezer (-60°C) 10.6 Cubic Feet
BVV™ ULTRA-Low Chest Style Freezer (-60°C) 10.6 Cubic Feet Single Compressor Model, Best Pick for Energy Savings! The brand new BVV™ 10.6 cubic foot -60°C Ultra-Low Chest Freezer is a great all-around ultra-low temperature freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting. These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. Key Features: Durable Powder Coated Exterior Aluminum Interior CFC-Refrigerant Free Large Digital Display Heavy Duty Rolling Casters 2 Wire Baskets for Extra Storage and Organization Specifications Model Number BVV™-60C106 Voltage 115V / 60Hz / 15A Capacity 10.6 Cu Ft. Temperature Range -30°C to -60°C Exterior Dimensions 50" x 30.1" x 34.8" Interior Dimensions 42.5" x 19.1" x 23.6" Weight 167lbs
$4,250.00
Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 16.2 Cubic Feet - ETL Rated
Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 16.2 Cubic Feet - ETL Rated The brand new Neocision ETL Rated 16.2 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting. Every unit accompanies various safety and protection features taking into consideration user and item safety. These highlights incorporate high and low-temperature alerts. These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. Key Features: ETL Rated Durable Powder Coated Exterior Touch Screen LCD with Datalogging Capabilities Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters (3) 1" ID Ports for putting lines through the freezer Backup battery Included. Specifications Model Number NEO-86C162 Voltage 115V / 60Hz / 13A Wattage 1560w Capacity 16.2cu ft. / 458L / 121G Temperature Range -40°C to -86°C Exterior Dimensions 79-3/4" x 36" x 40" Interior Dimensions 51-1/2" x 23" x 25" Weight 529lbs Certification ETL Rated
$7,500.00
Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 25 Cubic Feet - ETL Rated
Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 25 Cubic Feet - ETL Rated The brand new Neocision ETL Rated 25 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting. Every unit accompanies various safety and protection features taking into consideration user and item safety. These highlights incorporate high and low-temperature alerts. These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. Key Features: ETL Rated Durable Powder Coated Exterior Touch Screen LCD with Datalogging Capabilities Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters (3) 1" ID Ports for putting lines through the freezer Backup battery Included. Specifications Model Number BVV™-86C25 Voltage 115V / 60Hz / 15A Wattage 1800w Capacity 25cu ft. / 730L Internal Dimensions 34.5" x 51.5" x 23.5" Exterior Dimensions 43" x 76" x 36" Temperature Range -40°C to -86°C Weight 700lbs Rating ETL Rated
$9,000.00
Dry Ice Maker Machine Food Grade - Ultra Dense Block
Dry Ice Maker Machine Food Grade - Ultra Dense Block This dry ice machine makes ice the way you want it! Using 2 tons of hydraulic force to compress the formed CO2 snow into a solid brick. Other dry ice makers produce a loosely packed brick that sublimates quickly. Our bricks take up to 1.5+ hours to sublimate. All of the parts that touch liquid CO2 or ice are food-grade materials. Must use a CO2 tank with a dip tube!! Otherwise you will not get the liquid CO2 needed to make dry ice. Use Specifications 20lbs of CO2 Retail ($1/lb) (*Bulk rates as low as $0.55/lb) $20 Input of CO2 (LBS) per Use 1.75 Dry Ice Output (LBS) per Use 0.38 Lbs of Dry Ice made from 20 lbs CO2 4.34 Cost per lb of Dry Ice made (approx) $4.61 Brick Formation Time (approx) 25 Seconds Connection for CO2 (includes gasket not shown in photo*) CGA 320 Additionally, this dry ice maker comes with these extra items... 1 white plastic shim 1 Black upper gasket 1-Year BVV Warranty Assembled in the USA by BVV *Extreme cold temperatures will cause red paint to flake off of the jack over time. This is purely cosmetic.
$475.00
Cold Trap 2" Stainless Steel
Cold Trap 2" Stainless Steel This Stainless Steel Cold is designed and intended for use with the Polyscience IP60 Cold Finger (Can also be used with dry Ice) to create a cold trap that can achieve extremely frigid temperatures. These cold traps have 2 1/4" FNPT ports with one having a dip tube to the bottom of the trap to achieve higher vapor condensing rates with the 2" Diameter Center opening for the IP60. This Cold trap also has an insulating vacuum jacket around the entire container to maintain the subzero temperatures and help achieve the maximum minimal temperature of the IP60. Unlike many cold Traps on the market, this one is also made out of 304 Stainless steel and the internal parts are resistant to most chemicals and easily cleaned due to the Tri-Clamp lid design. Specifications Material 304 Stainless Steel Temperature Rating -200 to 200°C Ultimate Vacuum <100millitorr / microns Cold Finger Internal Dimensions 1.85" x 11.75" (Fits Polyscience IP60) Trap Internal Dimensions 5.85" x 10" Outside Dimensions 8" x 14" x 15" (Includes jacket gauge and valve hardware) Weight 28LBS
$465.00 - $508.00
Cold Trap 4" Stainless Steel
Cold Trap 4" Stainless Steel This Stainless Steel Cold is designed and intended for use with the Polyscience IP100 Cold Finger (Can also be used with dry Ice) to create a cold trap that can achieve extremely frigid temperatures. These cold traps have 2 1/4" FNPT ports with one having a dip tube to the bottom of the trap to achieve higher vapor condensing rates with the 4" Diameter Center opening for the IP100. This Cold trap also has an insulating vacuum jacket around the entire container to maintain the subzero temperatures and help achieve the maximum minimal temperature of the IP60. Unlike many cold Traps on the market, this one is also made out of 304 Stainless steel and the internal parts are resistant to most chemicals and easily cleaned due to the Tri-Clamp lid design. Specifications Material 304 Stainless Steel Temperature Rating -200 to 200°C Ultimate Vacuum <100millitorr / microns Cold Finger Internal Dimensions 3.85" x 11.75" (Fits Polyscience IP100) Trap Internal Dimensions 7.85" x 10" Outside Dimensions 10" x 16" x 15" (Includes jacket gauge and valve hardware) Weight 38LBS
$550.00 - $600.00
10" Cold Trap with KF25 Ports
10” X 10” KF25 Cold Trap Kit Cold traps are used in vacuum applications where contaminating vapors may be present, and a cold trap is required to assure vapors are condensed before reaching the vacuum pump. They can be used with any pump but are mostly used with rotary vane pumps. Protecting your pump will greatly increase the life of all your seals and internal components it will also assure that a full vacuum is pulled based on the pump’s capabilities. BVV’s 10”X10” KF25 Cold Trap features 2 qty. KF25 ports. The lower port is connected to the system that is under vacuum and the top to the vacuum pump. The KF25 allows for a larger bore and works great for high flow applications. This kit comes with 2 qty. KF25 rings and 2 qty. KF25 clamps ready to be connected in line with your setup. The internal pot is stainless steel and can hold 1.5 gallons which will hold the dry ice slurry or other method of getting cold. A silicone O-ring sits around the 1.5-gallon pot and creates a seal with the top of the 10”X10” base. For more specifications, please view table and diagrams below. Product Information Sheet **This cold trap comes pre-tested to pull down to 30 microns** **This cold trap is rated for applications down to 30 microns. If your application requires a deeper vacuum, please DO NOT USE THIS COLD TRAP** Specifications Model CTRAP10X10-B Material of Base and Internal Pot Stainless Steel Gasket Material Silicone Lid Material Silicone + Glass Vacuum Rating 30 microns Weight 29lbs Overall Height 11.5” Overall Diameter (Including Ports) 14” Cold Trap Surface Area 234.45 sq.in Internal Pot Volume 1.5 gallons Chemical Compatibility with Glass Lid Ethanol Excellent Acetone Good Water Excellent Propylene Glycol Excellent Isopropyl Alcohol Excellent Chemical Compatibility with Silicone O-Ring and Lid Seal Ethanol Good Acetone Good Pentane Good Hexane Good Heptane Good View of 10” x 10” Cold Trap
$850.00
1.5 Gallon Cold Trap (2QT Tank) Dry Ice, Liquid Nitrogen - GLASS LID
1.5 Gallon Cold Trap (2QT Tank) Dry Ice, Liquid Nitrogen - W/GLASS LID This is a complete Cold Trap and will come assembled for instant use. This Cold Trap is made of 304SS MADE IN USA, utilizing Glass lids for Durability, flexibility and Chemical Resistance to alcohol and solvents. This system is Recommended to protect pump from condensable vapors. This Trap comes with an industrial grade, heat cured silicone gasket designed only for our systems. There is nothing of equal quality in the market. The gasket itself is reversible (doubling the life of our system guaranteed) allowing customers to instantly take it off and flip it over. No adhesives are used! The system will maintain a vacuum seal only under vacuum. The vacuum pump will hold the interior 2 quart container for your Dry Ice Slurry in compression with the larger outer lid. The larger outer Lid will be held in compression with 1.5 gallon outer container. The connections on both sides are 1/4" MJIC flares or 1/4" Barbs that will connect to 1/4" HVAC or FJIC stainless steel hose. The Center Slurry Container has a lid for it, This lid simply helps prevent evaporation of your slurry. Temperature rated for -100-160F This Cold Trap comes assembled and includes: (1) 1.5gl high strength Stainless steel outer container (made of solid 304 stainless made in USA) (1) 2q interior Slurry Container (made of solid 304 stainless made in USA) (2) 1/2" thick clear Glass lids (2) Industrial grade silicone gasket (1) 1/4" HVAC Hose 5' Can withstand max working temps of 392F gasket only 60A durometer density (1) Max vacuum -29.5inHg (+/-.5Hg) (2) 1/4" MJIC or Barb Fittings Outside Container Internal Dimensions: 7.25" Diameter X 8.25" Tall To help remove condensable vapors, or when liquid nitrogen traps are not practical, our Cold Trap is the best option for preventing vapors from getting into your vacuum pump and contaminating it. This 1.5 gallon trap uses Glass lids for durability, flexibility, and chemical resistance. The system doesn’t use adhesives, and comes standard with a reversible gasket for enhanced quality that doubles its life. Made in the USA, the BVV™ Cold Trap comes with all parts pre-assembled, so you can get to work straight out of the box. Inside Container Internal Dimension: 4.75 Diameter by 6.5 Tall
$245.00 - $255.00
1.5 Gallon Cold Trap (2QT Tank) Dry Ice, Liquid Nitrogen
1.5 Gallon Cold Trap (2QT Tank) Dry Ice, Liquid Nitrogen (Comes with 2 Year Limited warranty) This is a complete cold trap and will come assembled for instant use. This cold trap is made of 304SS MADE IN USA, utilizing Polycarbonate lids for durability, flexibility and chemical resistance to Ethanol and Isopropyl (not compatible with Acetone). This system is recommended to protect pump from condensable vapors. This trap comes with an industrial grade, heat cured silicone gasket designed only for our systems. There is nothing of equal quality in the market. The gasket itself is reversible (doubling the life of our system guaranteed) allowing customers to instantly take it off and flip it over. No adhesives are used! The system will maintain a vacuum seal only under vacuum. The vacuum pump will hold the interior 2 quart container for your dry ice slurry in compression with the larger outer lid. The larger outer lid will be held in compression with 1.5 gallon outer container. The connections on both sides are 1/4" MJIC flares or 1/4" Barbs that will connect to 1/4" HVAC or FJIC stainless steel hose. The center slurry container has a lid - this lid simply helps prevent evaporation of your slurry. Temperature rated for -100-160F This cold trap comes assembled and includes: (1) 1.5gl high strength stainless steel outer container (made of solid 304 stainless made in USA) (1) 2q interior slurry container (made of solid 304 stainless made in USA) (2) 1/2" thick clear polycarbonate lids (2) industrial grade silicone gasket (1) 1/4" HVAC hose 5' Can withstand max working temps of 392F gasket only 60A durometer density (1) max vacuum -29.5inHg (+/-.5Hg) (2) 1/4" MJIC or Barb Fittings Outside container internal dimensions: 7.25" diameter X 8.25" tall To help remove condensable vapors, or when liquid nitrogen traps are not practical, our cold trap is the best option for preventing vapors from getting into your vacuum pump and contaminating it. This 1.5 gallon trap uses polycarbonate lids for durability, flexibility, and chemical resistance. The system doesn’t use adhesives, and comes standard with a reversible gasket for enhanced quality that doubles its life. Made in the USA, the BVV™ Cold Trap comes with all parts pre-assembled, so you can get to work straight out of the box. Inside container internal dimension: 4.75" diameter by 6.5" tall
$230.00 - $240.00
BVV™ Dewar Glass Cold Trap
BVV™ Dewar Glass Cold Trap This dewar style glass is designed for maximum vapor condensation and it also has a 24/40 bottom joint and (2) GL-14 8mm Hose Barbs *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement.
$250.00
BVV™ Glass Cold Trap - Ribbed (Made in USA)
BVV™ Glass Cold Trap - Ribbed This dewar style glass is designed to increase surface area for maximum vapor condensation and it also has 24/40 or 34/45 jointed connections to increase vapor flow. Note: The bottom joint will always be 24/40. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement.
$790.00
BVV™ Dewar Style Glass Cold Trap Kit
Dewar Style Glass Cold Trap The Dewar Style Glass Cold Trap with GL-14 Barb Fittings allows the user to load dry ice into the inner portion of the cold trap from the top to allow maximum condensation temperatures. This protects your vacuum pump and captures any vapors that were lost during evaporation or distillation. Made in the USA. Dewar Style Glass Cold Traps includes the following: Metal Keck Clip Boss Head Lab Stand Chain Clamp 250ml Round Bottom Flask 24/40 Joint 250-500ml Cork Stand Specifications: USA Made 24/40 Male Ground Joint GL-14 8mm Barb Connections OD = 3.8" ID = 2.75" Height = 14.75" *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$350.00
Polyscience 15 Liter Advanced Digital Refrigerated Circulator (-30°C/200°C)
Polyscience 15 Liter Advanced Digital Refrigerated Circulator (-30°C/200°C) ***Note: This item has a lead time of 2-3 weeks depending on stock availability.*** Description: -30, 15 L Ref. Circulator Controller Type: Advanced Digital Display: 3.75" Touch-Pad LCD Connectivity: Ethernet, USB A & B, RS232/addressable RS485, External Temperature Probe Languages Supported: 4: French, German, Spanish, English Swivel 180 Rotating Controller: Yes Working Temperature Range °C: -30° to 200° Temperature Stability °C: ±0.01° Fluid Optimization/Specific Heat Tuning: Automatic and/or user-adjustable Temperature Calibration Capability: 1-point Working Access (L x W x D) (cm): 21.2 x 27.6 x 14 cm Pump Type: Pressure/Suction External Temperature Control Capability: Yes Flammability Class (DIN 12876-1): III (FL) Specifications Working Temperature Range °F -22° to 392° Working Temperature Range °C -30° to 200° Nominal Cooling Capacity @ +20C (W) 915 Reservoir Capacity (gallons) 3.96 Reservoir Capacity (liters) 15 Reservoir/Tank Material Stainless Steel Reservoir Cover Included DuraTop Yes LidDock Yes Cleanable Air Filter Yes Working Access (L x W x D) (inches) 8.35 x 10.88 x 5.5 in Working Access (L x W x D) (cm) 21.2 x 27.6 x 14 cm Temperature Stability °F ±0.02° Temperature Stability °C ±0.01° Display 3.75" Touch-Pad LCD Display Resolution (Set) 0.01 Display Resolution (Read) 0.01 Pump Type Pressure/Suction Pump Speed Variable Process Connections 1/4" (F) NPT External Temperature Control Capability Yes Flammability Class (DIN 12876-1) III (FL) Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes WhisperCool Environmental Control Technology Yes Cool Command Refrigeration Technology Yes Reservoir Drain Yes Included Software PolyTemp Viewer, USB driver Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 22.4 x 14.5 x 26.9 in Overall Dimensions (L x W x H) (cm) 56.9 x 36.8 x 68.3 cm Refrigerant R404A Environmental Compliance RoHS, WEEE Shipping Weight (pounds) 118.0 Shipping Weight (kilograms) 53.5 60Hz Part Number AD15R-30-A11B Maximum Pressure (psi) 4.3 Maximum Pressure (bar) 0.30 Maximum Pressure Flow Rate (gpm) 5.30 Maximum Pressure Flow Rate (l/min) 20.1 Maximum Suction Flow Rate (gpm) 3.9 Maximum Suction Flow Rate (l/min) 14.7 Cooling Capacity @ -20°C (W) 165 Cooling Capacity @ 0°C (W) 505 Cooling Capacity @ +20°C (W) 915 Included Hardware Nylon hose adapters for 3/8", 1/4", and 3/16" Heater Wattage 1100 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/13 Regulatory Approvals ETL Certifications: Regulatory Approvals: ETL Circulating Bath Operator's Manual
$6,350.00
Polyscience 28 Liter Advanced Digital Refrigerated Circulator (-30°C/200°C)
Polyscience 28 Liter Advanced Digital Refrigerated Circulator (-30°C/200°C) Specification Description -30, 28 L Ref. Circulator Controller Type Advanced Digital Display 3.75" Touch-Pad LCD Connectivity Ethernet, USB A & B, RS232/addressable RS485, External Temperature Probe Languages Supported 4: French, German, Spanish, English Swivel 180 Rotating Controller Yes Working Temperature Range °C -30° to 200° Temperature Stability °C ±0.01° Fluid Optimization/Specific Heat Tuning Automatic and/or user-adjustable Temperature Calibration Capability 1-point Working Access (L x W x D) (cm) 31.4 x 35.9 x 14 cm Pump Type Pressure/Suction External Temperature Control Capability Yes Flammability Class (DIN 12876-1) III (FL) Working Temperature Range °F -22° to 392° Working Temperature Range °C -30° to 200° Nominal Cooling Capacity @ +20C (W) 915 Reservoir Capacity (gallons) 7.4 Reservoir Capacity (liters) 28 Reservoir/Tank Material Stainless Steel Reservoir Cover Included DuraTop Yes LidDock Yes Cleanable Air Filter Yes Working Access (L x W x D) (inches) 12.35 x 14.13 x 5.5 in Working Access (L x W x D) (cm) 31.4 x 35.9 x 14 cm Temperature Stability °F ±0.02° Temperature Stability °C ±0.01° Display 3.75" Touch-Pad LCD Display Resolution (Set) 0.01 Display Resolution (Read) 0.01 Pump Type Pressure/Suction Pump Speed Variable Process Connections 1/4" (F) NPT External Temperature Control Capability Yes Flammability Class (DIN 12876-1) III (FL) Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes Reservoir Drain Yes Cooling Coil Yes Included Software PolyTemp Viewer, USB driver Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 26.5 x 18 x 26.9 in Overall Dimensions (L x W x H) (cm) 67.2 x 45.7 x 68.3 cm Refrigerant R404A Environmental Compliance RoHS, WEEE Shipping Weight (pounds) 146.0 Shipping Weight (kilograms) 66.1 Catalog Page Number 40-41 60 Hz Only Part Number AD28R-30-A11B Maximum Pressure (psi) 4.3 Maximum Pressure (bar) 0.30 Maximum Pressure Flow Rate (gpm) 5.30 Maximum Pressure Flow Rate (l/min) 20.1 Maximum Suction Flow Rate (gpm) 3.9 Maximum Suction Flow Rate (l/min) 14.7 Cooling Capacity @ -20°C (W) 165 Cooling Capacity @ 0°C (W) 505 Cooling Capacity @ +20°C (W) 915 Cooling Capacity @ +100°C (W) 915 Included Hardware Nylon hose adapters for 3/8", 1/4", and 3/16" Heater Wattage 1100 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/10 Regulatory Approvals ETL Key Features: Intuitive 3.75" (9.5cm) display with touch-pad control 4 Languages: French, German, Spanish, English Swivel 180 Rotating Controller On-board connectivity: Ethernet, USB A & B, RS232/addressable RS485, External Temperature Probe On-screen prompts Automatic performance optimization and specific heat tuning Single-point calibration capability Certifications Regulatory Approvals: CE Regulatory Approvals: ETL Operator's Manual
$7,000.00
Polyscience 15 Liter Advanced Digital Refrigerated Circulator (-40°C/200°C)
Polyscience 15 Liter Advanced Digital Refrigerated Circulator (-40°C/200°C) Specification Description -40, 15 L Ref. Circulator Controller Type Advanced Digital Display 3.75" Touch-Pad LCD Connectivity Ethernet, USB A & B, RS232/addressable RS485, External Temperature Probe Languages Supported 4: French, German, Spanish, English Swivel 180 Rotating Controller Yes Working Temperature Range °C -40° to 200° Temperature Stability °C ±0.01° Fluid Optimization/Specific Heat Tuning Automatic and/or user-adjustable Temperature Calibration Capability 1-point Working Access (L x W x D) (cm) 21.2 x 27.6 x 14 cm Pump Type Pressure/Suction External Temperature Control Capability Yes Flammability Class (DIN 12876-1) III (FL) Working Temperature Range °F -40° to 392° Working Temperature Range °C -40° to 200° Nominal Cooling Capacity @ +20C (W) 1000 Reservoir Capacity (gallons) 3.96 Reservoir Capacity (liters) 15 Reservoir/Tank Material Stainless Steel Reservoir Cover Included DuraTop Yes LidDock Yes Cleanable Air Filter Yes Working Access (L x W x D) (inches) 8.35 x 10.88 x 5.5 in Working Access (L x W x D) (cm) 21.2 x 27.6 x 14 cm Temperature Stability °F ±0.02° Temperature Stability °C ±0.01° Display 3.75" Touch-Pad LCD Display Resolution (Set) 0.01 Display Resolution (Read) 0.01 Pump Type Pressure/Suction Pump Speed Variable Process Connections 1/4" (F) NPT Flammability Class (DIN 12876-1) III (FL) Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes WhisperCool Environmental Control Technology Yes Cool Command Refrigeration Technology Yes Reservoir Drain Yes Included Software PolyTemp Viewer, USB driver Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 22.4 x 14.5 x 26.9 in Overall Dimensions (L x W x H) (cm) 56.9 x 36.8 x 68.3 cm Refrigerant R452A Environmental Compliance RoHS, WEEE Shipping Weight (pounds) 118.0 Shipping Weight (kilograms) 53.5 Catalog Page Number 40-41 60 Hz Only Part Number AD15R-40-A11B Maximum Pressure (psi) 4.3 Maximum Pressure (bar) 0.30 Maximum Pressure Flow Rate (gpm) 5.30 Maximum Pressure Flow Rate (l/min) 20.1 Maximum Suction Flow Rate (gpm) 3.9 Maximum Suction Flow Rate (l/min) 14.7 Cooling Capacity @ -20°C (W) 265 Cooling Capacity @ 0°C (W) 650 Cooling Capacity @ +20°C (W) 1000 Cooling Capacity @ +100°C (W) 1000 Included Hardware Nylon hose adapters for 3/8", 1/4", and 3/16" Heater Wattage 1100 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/13 Regulatory Approvals ETL Key Features: Intuitive 3.75" (9.5cm) display with touch-pad control 4 Languages: French, German, Spanish, English Swivel 180 Rotating Controller On-board connectivity: Ethernet, USB A & B, RS232/addressable RS485, External Temperature Probe On-screen prompts Automatic performance optimization and specific heat tuning Single-point calibration capability Operators Manual
$5,850.00
Polyscience 7 Liter MX Refrigerated Circulator (-20°C to 135°C)
Polyscience 7 Liter MX Refrigerated Circulator (-20°C/135°C) Specification Description -20, 7 L Ref. Circulator Controller Type MX Display 3.25" LCD Working Temperature Range °C -20° to 135° Temperature Stability °C ±0.07° Temperature Calibration Capability 1-point Working Access (L x W x D) (cm) 15.7 x 14.2 x 12.7 cm Pump Type Pressure Flammability Class (DIN 12876-1) I (NFL) Working Temperature Range °F -4° to 275° Working Temperature Range °C -20° to 135° Nominal Cooling Capacity @ +20C (W) 200 Reservoir Capacity (gallons) 1.85 Reservoir Capacity (liters) 7 Reservoir/Tank Material Stainless Steel Reservoir Cover Included DuraTop Yes LidDock Yes Cleanable Air Filter Yes Working Access (L x W x D) (inches) 6.18 x 5.59 x 5 in Working Access (L x W x D) (cm) 15.7 x 14.2 x 12.7 cm Temperature Stability °F ±0.13° Temperature Stability °C ±0.07° Display 3.25" LCD Display Resolution (Set) 0.01 Display Resolution (Read) 0.01 Pump Type Pressure Pump Speed One Process Connections 1/2" O.D. Barbed Tubes Flammability Class (DIN 12876-1) I (NFL) Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes Reservoir Drain Yes Included Software PolyTemp Viewer, USB driver Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 21.3 x 8.7 x 25.4 in Overall Dimensions (L x W x H) (cm) 54.1 x 22.1 x 64.5 cm Refrigerant R134a Environmental Compliance RoHS, WEEE Shipping Weight (pounds) 84.0 Shipping Weight (kilograms) 38.1 Catalog Page Number 44-45 60 Hz Only Part Number MX07R-20-A11B Maximum Pressure (psi) 2.3 Maximum Pressure (bar) 0.16 Maximum Pressure Flow Rate (gpm) 3.60 Maximum Pressure Flow Rate (l/min) 13.5 Cooling Capacity @ -20°C (W) 30 Cooling Capacity @ 0°C (W) 120 Cooling Capacity @ +20°C (W) 200 Cooling Capacity @ +100°C (W) 200 Included Hardware Fitting Kit for External Applications Heater Wattage 1100 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/12 Regulatory Approvals ETL Key Features: Large, Universal icon and English display On-screen prompts Single-point calibration capability Certifications: Regulatory Approvals: ETL Operator's Manual
$3,951.00
Polyscience 45 Liter Advanced Digital Refrigerated Circulator (-25°C/135°C)
Polyscience 45 Liter Advanced Digital Refrigerated Circulator (-25°C/135°C) Specification Description -25, 45 L Ref. Circulator Controller Type Advanced Digital Display 3.75" Touch-Pad LCD Connectivity Ethernet, USB A & B, RS232/addressable RS485, External Temperature Probe Languages Supported 4: French, German, Spanish, English Swivel 180 Rotating Controller Yes Working Temperature Range °C -25° to 135° Temperature Stability °C ±0.01° Fluid Optimization/Specific Heat Tuning Automatic and/or user-adjustable Temperature Calibration Capability 1-point Working Access (L x W x D) (cm) 54.9 x 39.8 x 14 cm Pump Type Pressure/Suction External Temperature Control Capability Yes Flammability Class (DIN 12876-1) III (FL) Working Temperature Range °F -13° to 275° Working Temperature Range °C -25° to 135° Nominal Cooling Capacity @ +20C (W) 1400 Reservoir/Tank Material Stainless Steel Reservoir Capacity (gallons) 11.88 Reservoir Capacity (liters) 45 Reservoir/Tank Material Stainless Steel Reservoir Cover Included DuraTop Yes Cleanable Air Filter Yes Working Access (L x W x D) (inches) 21.6 x 15.68 x 5.5 in Working Access (L x W x D) (cm) 54.9 x 39.8 x 14 cm Temperature Stability °F ±0.02° Temperature Stability °C ±0.01° Display 3.75" Touch-Pad LCD Display Resolution (Set) 0.01 Display Resolution (Read) 0.01 Pump Type Pressure/Suction Pump Speed Variable Process Connections 1/4" (F) NPT External Temperature Control Capability Yes Flammability Class (DIN 12876-1) III (FL) Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes WhisperCool Environmental Control Technology Yes Cool Command Refrigeration Technology Yes Reservoir Drain Yes Included Software PolyTemp Viewer, USB driver Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 35.8 x 22.4 x 42.1 in Overall Dimensions (L x W x H) (cm) 90.9 x 56.8 x 107 cm Refrigerant R134a Environmental Compliance RoHS, WEEE Shipping Weight (pounds) 180.0 Shipping Weight (kilograms) 81.5 Catalog Page Number 40-41 60 Hz Only Part Number AD45R-20-A13D Maximum Pressure (psi) 4.3 Maximum Pressure (bar) 0.30 Maximum Pressure Flow Rate (gpm) 5.30 Maximum Pressure Flow Rate (l/min) 20.1 Maximum Suction Flow Rate (gpm) 3.9 Maximum Suction Flow Rate (l/min) 14.7 Cooling Capacity @ -20°C (W) 250 Cooling Capacity @ 0°C (W) 800 Cooling Capacity @ +20°C (W) 1400 Cooling Capacity @ +100°C (W) 1400 Included Hardware Nylon hose adapters for 3/8", 1/4", and 3/16" Heater Wattage 2200 Electrical Requirements (VAC/Hz/Ph/A) 208-230/60/1/13 Regulatory Approvals ETL Key Features: Intuitive 3.75" (9.5cm) display with touch-pad control 4 Languages: French, German, Spanish, English Swivel 180 Rotating Controller On-board connectivity: Ethernet, USB A & B, RS232/addressable RS485, External Temperature Probe On-screen prompts Automatic performance optimization and specific heat tuning Single-point calibration capability Certifications: Regulatory Approvals: ETL Operator's Manual
$9,938.00
PolyScience LS5 Benchtop Chiller with Turbine Pump, 120V, 60Hz
PolyScience LS5 Benchtop Chiller with Turbine Pump, 120V, 60Hz Key Specifications: Description: LS Series 1/2 HP Benchtop Chiller, Turbine Pump; 43.4 psi; 9.8 l/min Display: LED Connectivity: Optional: RS232 Working Temperature Range °C: -20° to 40° Temperature Stability °C: ±0.1° Temperature Calibration Capability: 1-point Pump Type: Turbine Specifications Working Temperature Range °F -4° to 104° Working Temperature Range °C -20° to 40° Reservoir Capacity (gallons) 0.7 Reservoir Capacity (liters) 2.65 Reservoir Cover Screw-on Cap Cleanable Air Filter Yes Temperature Stability °F ±0.2° Temperature Stability °C ±0.1° Display LED Pump Type Turbine Pump Speed Constant, Single Speed Process Connections 1/2" (F) NPT Over-Temperature Protection / Failsafe Heater Control Yes Reservoir Liquid Level Indicator Yes WhisperCool Environmental Control Technology Yes Cool Command Refrigeration Technology Yes Reservoir Drain Yes Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 23.9 x 10 x 19 in Overall Dimensions (L x W x H) (cm) 60.7 x 25.4 x 48.3 cm Compressor Size (HP) 1/2 Refrigerant R452A Shipping Weight (pounds) 102.0 Shipping Weight (kilograms) 46.3 Catalog Page Number 98-99 Part Number LS51TX1A110C Maximum Pressure (psi) 43.4 Maximum Pressure (bar) 3.00 Maximum Pressure Flow Rate (gpm) 2.60 Maximum Pressure Flow Rate (l/min) 9.8 Cooling Capacity @ -20°C (W) 150 Cooling Capacity @ -10°C (W) 345 Cooling Capacity @ -5°C (W) 395 Cooling Capacity @ 0°C (W) 540 Cooling Capacity @ +10°C (W) 790 Cooling Capacity @ +20°C (W) 900 Cooling Capacity @ +30°C (W) 1020 Cooling Capacity @ +40°C (W) 1140 Included Hardware Two sets of Inlet/Outlet Adapters: ½ inch male NPT, 5/8 inch male NPT Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/12 Regulatory Approvals TUV
$5,161.00
Polyscience LS 1/2HP Chiller, Centrifugal Pump
Polyscience LS 1/2HP Chiller, Centrifugal Pump Note: This item has a lead time of 2-3 weeks depending on stock availability. Key Specifications Description LS Series 1/2 HP Benchtop Chiller, Turbine Pump; 43.4 psi; 9.8 l/min Display LED Connectivity Optional: RS232 Working Temperature Range °C -20° to 40° Temperature Stability °C ±0.1° Temperature Calibration Capability 1-point Pump Type Turbine Working Temperature Range °F -4° to 104° Working Temperature Range °C -20° to 40° Reservoir Capacity (gallons) 0.7 Reservoir Capacity (liters) 2.65 Reservoir Cover Screw-on Cap Cleanable Air Filter Yes Temperature Stability °F ±0.2° Temperature Stability °C ±0.1° Display LED Pump Type Centrifugal Pump Speed Constant, Single Speed Process Connections 1/2" (F) NPT Over-Temperature Protection / Failsafe Heater Control Yes Reservoir Liquid Level Indicator Yes WhisperCool Environmental Control Technology Yes Cool Command Refrigeration Technology Yes Reservoir Drain Yes Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 23.9 x 10 x 19 in Overall Dimensions (L x W x H) (cm) 60.7 x 25.4 x 48.3 cm Compressor Size (HP) 1/2 Refrigerant R452A Shipping Weight (pounds) 102.0 Shipping Weight (kilograms) 46.3 Catalog Page Number 98-99 60 Hz Only Part Number LS51MX1A110C Maximum Pressure (psi) 43.4 Maximum Pressure (bar) 3.00 Maximum Pressure Flow Rate (gpm) 2.60 Maximum Pressure Flow Rate (l/min) 9.8 Cooling Capacity @ -20°C (W) 150 Cooling Capacity @ -10°C (W) 345 Cooling Capacity @ -5°C (W) 395 Cooling Capacity @ 0°C (W) 540 Cooling Capacity @ +10°C (W) 790 Cooling Capacity @ +20°C (W) 900 Cooling Capacity @ +30°C (W) 1020 Cooling Capacity @ +40°C (W) 1140 Included Hardware Two sets of Inlet/Outlet Adapters: ½ inch male NPT, 5/8 inch male NPT Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/12 Regulatory Approvals TUV Key Features: Optimized for high performance at low temperatures Capable of cooling multiple rotary evaporators WhisperCool Environmental Control System Large, easy to read LED display Space-saving design Cooling at ambient temperatures as high as 35C Low flow shutoff and alarm, high and low temperature alarms Simple setup, operation, and maintenance Centrifugal or turbine pump Fluid level indicator RS232 communication and external water filter optional Regulator Approvals: TUV Approvals CE Approvals Operators Manual
$4,834.00
Polyscience 1.5 HP Chiller, Positive Displacement Pump; Air-Cooled
Polyscience 1.5 HP Chiller, Positive Displacement Pump; Air-Cooled Description: 1.5 HP Chiller, Positive Displacement Pump; Air-Cooled Display: LED Connectivity: Optional: RS232, RS485 Working Temperature Range °C: 5° to 35° Temperature Stability °C: ±0.5° Temperature Calibration Capability: 1-point Pump Type: Positive Displacement Key Features High capacity cooling for lasers, electron microscopes, and other laboratory applications Small footprint conserves floor space Displays temperature and pressure or flow rate simultaneously User-adjustable temperature, pressure, and flow rate alarms Simple operation and maintenance Air- or water-cooled Positive displacement (PD) or turbine (T) pump; other pump options also available Common Specifications Working Temperature Range °F 41° to 95° Working Temperature Range °C 5° to 35° Reservoir Capacity (gallons) 3.5 Reservoir Capacity (liters) 13.25 Reservoir/Tank Material Polyethylene Reservoir Cover Screw-on Cap Cleanable Air Filter Yes Cleanable Fluid Filter Yes Temperature Stability °F ±0.9° Temperature Stability °C ±0.5° Display LED Display Resolution (Read) 0.1 Pump Type Positive Displacement Process Connections 1/2" (F) NPT Over-Temperature Protection / Failsafe Heater Control Yes Reservoir Liquid Level Indicator Yes Reservoir Drain Yes Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 30.5 x 19 x 26 in Overall Dimensions (L x W x H) (cm) 78 x 48 x 66 cm Compressor Size (HP) 1.5 Refrigerant R134a Shipping Weight (pounds) 340.0 Shipping Weight (kilograms) 154.0 Catalog Page Number 104 Hz (Hertz) 60 Hz Only 50 Hz Only Part Number 6860P46A270D 6850P46A270E Maximum Pressure (psi) 100.0 83.0 Maximum Pressure (bar) 6.90 5.72 Maximum Pressure Flow Rate (gpm) 3.50 2.90 Maximum Pressure Flow Rate (l/min) 13.2 11.0 Cooling Capacity @ +10°C (W) 4420 3715 Cooling Capacity @ +20°C (W) 5200 4371 Cooling Capacity @ +30°C (W) 5980 5027 Heater Wattage 1000 1000 Electrical Requirements (VAC/Hz/Ph/A) 230/60/1/21.1 240/50/1/20.8 Regulatory Approvals TUV CSA, CUL, CE
$10,243.00
Polyscience 6100 Series 1 HP Chiller, Turbine Pump
Polyscience 6100 Series 1 HP Chiller, Turbine Pump Key Specifications: 6100 Series 1 HP Chiller with Turbine Pump, 100psi; 13.2l/min Display: LED Working Temperature Range C: -10 to 40 Temperature Stability: +/-0.1 Temperature Calibration Capability: 1-point Pump Type: Turbine Key Features: Large, dual displays present temperature and pressure or flow rate simultaneously Compact, portable design takes up less floor space Cooling at ambient temperatures as high as 35C Powerful Turbine Pump User-adjusable temperature, pressure, and flow rate alarms Cool Command, WhisperCool Common Specifications: Working Temperature Range F: 14 to 104 Working Temperature Range C: -10 to 40 Reservoir Capacity (gallons): 1.11 Reservoir Capcity (liters): 4.2 Reservoir Cover: Screw-on cap Cleanable Air Filter: Yes Cleanable Fluid Filter: Yes Temperature Stability F: +/-0.2 Temperature Stability C: +/-0.1 Display: LED Dispplay Resolution (Read): 0.1 Pump Type: Turbine Process Connections: 1/2" FNPT Over-Temperature Protection / Failsafe Heater Control: Yes Reservoir Liquid Level Indicator: Yes Reservoir Drain: Yes Cool Command Refrigeration Technology: Yes WhisperCool Environmental Control Techonology: Yes Maximum Ambient Temperature F: 95 Maximum Ambient Tmeperature C: 35 Overall Dimensions (LxWxH inches): 27.6 x 14.5 x 22.6 Overall Dimensions (LxWxH cm): 70 x 36.8 x 57.5 Compressor Size (HP): 1 Refrigerant: R134a Shipping Weight (pounds): 199 Shipping Weight (kilograms): 90 60 Hz Only Part Number: 6160T21A130D Maximum Pressure (psi): 100 Maximum Pressure (bar): 6.90 Maximum Pressure Flow Rate (gpm): 3.50 Maximum Pressure Flow Rate (l/min): 13.2 Cooling Capacity @ +10C(W): 1925 Cooling Capacity @ +20C(W): 2900 Cooling Capacity @ +30C(W): 3103 Electrical Requirements (VAC/Hz/Ph/A): 230/60/1/12.2 Certifications Regulatory Approvals: TUV
$7,900.00
Polyscience DuraChill 1.5HP Chiller, Turbine Pump
Polyscience DuraChill 1.5HP Chiller, Turbine Pump Note: This item has a lead time of 2-3 weeks depending on stock availability Specification Description 1.5 HP Chiller, Turbine Pump; Air-Cooled Display LED Connectivity Optional: RS232, RS485 Working Temperature Range °C 5° to 35° Temperature Stability °C ±0.5° Temperature Calibration Capability 1-point Pump Type Turbine Working Temperature Range °F 41° to 95° Working Temperature Range °C 5° to 35° Reservoir Capacity (gallons) 3.5 Reservoir Capacity (liters) 13.25 Reservoir/Tank Material Polyethylene Reservoir Cover Screw-on Cap Cleanable Air Filter Yes Cleanable Fluid Filter Yes Temperature Stability °F ±0.9° Temperature Stability °C ±0.5° Display LED Display Resolution (Read) 0.01 Pump Type Turbine Process Connections 1/2" (F) NPT Over-Temperature Protection / Failsafe Heater Control Yes Reservoir Liquid Level Indicator Yes Reservoir Drain Yes Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 30.5 x 19 x 26 in Overall Dimensions (L x W x H) (cm) 78 x 48 x 66 cm Compressor Size (HP) 1.5 Refrigerant R134a Shipping Weight (pounds) 340.0 Shipping Weight (kilograms) 154.0 Catalog Page Number 104 60 Hz Only Part Number 6860T56A270D Maximum Pressure (psi) 100.0 Maximum Pressure (bar) 6.90 Maximum Pressure Flow Rate (gpm) 11.00 Maximum Pressure Flow Rate (l/min) 41.6 Cooling Capacity @ +10°C (W) 4420 Cooling Capacity @ 0°C (W) 120 Cooling Capacity @ +20°C (W) 5200 Cooling Capacity @ +30°C (W) 5980 Heater Wattage 1000 Electrical Requirements (VAC/Hz/Ph/A) 230/60/1/23.1 Regulatory Approvals TUV Key specifications: High capacity cooling for lasers, electron microscopes, and other laboratory applications Small footprint conserves floor space Displays temperature and pressure or flow rate simultaneously User-adjustable temperature, pressure, and flow rate alarms Simple operation and maintenance Air- or water-cooled Positive displacement (PD) or turbine (T) pump; other pump options also available Certifications Regulatory Approvals: TUV Operator's Manual
$11,431.00
Polyscience Durachill Chiller; 4.2 L; 208/230 V
Polyscience Durachill Chiller; 4.2 L; 208/230 V PolyScience CA10A3T1-41AA1N Offers Features: Large, full-color touchscreen display with intuitive interface and support for five different languages Home screen simultaneously displays set temperature, actual temperature, fluid pressure, fluid level, air filter status and timer Self-changing air filter system eliminates preventative maintenance by automatically changing the filter media at user-definable intervals Continuous fluid level monitoring protects pump and prevents freezing Whispercool® noise reduction system reduces operating noise levels to the almost imperceptible levels while maintaining optimal cooling performance Reduced global warming potential through a highly optimized refrigeration system design that greatly reduces the amount of refrigerant gas needed in the chiller and allows for migration to natural refrigerants that have little or no global warming potential Self-diagnostic system compares the chiller's functionality to its operating state the day it was built to minimize operating downtime and unnecessary service calls Compact, portable design takes up less floor space Cooling at ambient temperatures as high as 30°C Components are recyclable and meet or exceed global environmental standards UV Light Biological Growth Inhibitor System eliminates the need for algaecides User-adjustable temperature, pressure, and flow rate alarms Heat up to 70°C, without additional options Front fill reservoir access Externally accessible adjustable pressure regulator valve Full color touch screen display The color touch screen display gives you all the information you need at a glance. The screen will display continuous status of set temperature, actual temperature, reservoir fill level and output pressure as well as the status of your air filter. System messages are provided in easy to read text instead of confusing error codes. Dynamic self-changing filter Preprogrammed to change its own air filter once a month for a two year period, and the change interval can be adjusted to suit your operating environment. This will dramatically reduce downtime and unnecessary service calls and relieve you of the burden of preventative maintenance on your chiller. UV light biological growth inhibitor The UV Light Biological Growth Inhibitor will continuously control biological growth in the fluid path without the need to add chemical growth inhibitors and preventing algicides from being released into the world's waterways. Front fill reservoir The chiller offers a conveniently located front fill reservoir. You no longer have to go to the back of the chiller top open to fill the reservoir. It has the fill port in the front, making it easy to access, avoiding spills and saving time. Continuous liquid level monitoring Because pump seals will fail in as little as 30 seconds of being run dry, the chiller includes a state-of-the-art capacitance liquid level sensor to protect the pump from premature failure. If the fluid level becomes low, the chiller will give you visual and audible alarms. If the fluid level reaches a point where there's a risk of pulling air into the pump, it will shut the chiller down and present another alarm. Whispercool® noise reduction This high-performance chiller utilizes noise reduction system. The Whispercool® system evaluates the demand for cooling from the application then slows the fan speed to the minimum necessary to achieve control point, making the chiller extremely quiet while maintaining optimal temperature control at the same time. Applications Heat removal Specifications Cooling Capacity At 20°C: 2.9 kWAt 10°C: 1.93 kWAt 0°C: 1 kW Fluid Temperature Range 14 to 158°F (-10 to 70°C) Temperature Stability ±0.1°C Displayable Units Temperature: °C or °FPressure: psi or kPa Pump Inlet and Outlet ½" female NPT Connectivity RS-232, USB Serial Port Emulation, USB TMC, Dry Contact On/Off/Status Selectable Operating Languages English, Spanish, French, German, Mandarin Self-Changing Air Filter Yes UV Biological Growth Inhibitor Yes Ambient Air Temperature Tracking Yes Pump Pressure Range 20 to 90 psi (138 to 689 kPa) Maximum Pump Flow Rate 3.5 gpm (13.2 lpm) Power Requirements 230 V, 60 Hz, 13.5 A Dimensions 33 x 22 x 33" (84 x 56 x 84 cm) Weight 177 lbs (80.3 kg) Data sheet Manual
$8,307.00
Polyscience 3 HP High Capacity Chiller; Air-Cooled - Up to 10.5kW @ 20°C
Polyscience 3 HP High Capacity Chiller; Air-Cooled - Up to 10.5kW @ 20°C Key Specifications Description: 3 HP Chiller; Air-Cooled; Up to 10.5kW @ 20°C Display: LED Connectivity: Standard: RS232; Optional: RS485 Working Temperature Range °C: 5° to 35° Temperature Stability °C: ±0.5° Temperature Calibration Capability: 1-point Key Features Chillers 2HP and up are not available outside of the United States High capacity cooling for lasers, EDM equipment, injection molding, and other heat removal applications Displays temperature and pressure or flow rate simultaneously User-adjustable temperature, pressure, and flow rate alarms Simple operation and maintenance Air- or water-cooled (3 HP models) Wide variety of pump options available Common Specifications Working Temperature Range °F 41° to 95° Working Temperature Range °C 5° to 35° Cooling Capacity Up to 10.5kW @ 20°C Reservoir Capacity (gallons) 7 Reservoir Capacity (liters) 26.5 Reservoir/Tank Material Contact PolyScience for Options Reservoir Cover Screw-on Cap Cleanable Air Filter Yes Cleanable Fluid Filter Yes Temperature Stability °F ±0.9° Temperature Stability °C ±0.5° Display LED Display Resolution (Read) 0.1 Pump Type Contact PolyScience for Options Process Connections 3/4" (F) NPT Over-Temperature Protection / Failsafe Heater Control Yes Reservoir Liquid Level Indicator Yes Cool Command Refrigeration Technology Yes Reservoir Drain Yes Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 30.5 x 37 x 42 in Overall Dimensions (L x W x H) (cm) 78 x 94 x 107 cm Compressor Size (HP) 3 Refrigerant R134a Shipping Weight (pounds) 570.0 Shipping Weight (kilograms) 259.0 Catalog Page Number 105 Operator's Manual PDF Version
$15,350.00
Polyscience IP-60 Low Temperature Cooler, 1.5" Rigid Coil Probe
Polyscience IP-60 Low Temperature Cooler, 1.5" Rigid Coil Probe ***Note: This item has a possible lead time of 2-3 weeks depending on stock availability.*** Specification Description Immerson Probe-60, 1.5" Rigid Coil Working Temperature Range °C -60° to -20° Temperature Control (°C) Fixed at -60° Working Temperature Range °F -76° to -4° Working Temperature Range °C -60° to -20° Temperature Control (°F) Fixed at -76° Temperature Control (°C) Fixed at -60° Maximum Ambient Temperature °F 86° Maximum Ambient Temperature °C 30° Overall Dimensions (L x W x H) (inches) 11 x 10 x 9 in Overall Dimensions (L x W x H) (cm) 27.9 x 25.4 x 22.9 cm Refrigerant R404A & R508B Immersion Probe Type Rigid Coil Probe Diameter (inches) 1.5 Probe Diameter (cm) 3.81 Probe Length (inches) Coil: 4 / Exposed: 15 Probe Length (cm) Coil: 10.2 / Exposed: 38.1 Flexible Hose Diameter (inches) 1.5 Flexible Hose Diameter (cm) 3.81 Flexible Hose Length (feet) 4 Flexible Hose Length (m) 1.22 Shipping Weight (pounds) 49.0 Shipping Weight (kilograms) 22.0 Catalog Page Number 114-115 60 Hz Only Part Number P60N2A101B Cooling Capacity @ -60°C (W) 0 Cooling Capacity @ -40°C (W) 100 Cooling Capacity @ -30°C (W) 125 Cooling Capacity @ -20°C (W) 150 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/5 Key Features: Continuous cooling to temperatures as low as -60C Designed to run at maximum cooling An economic alternative to dry ice or liquid nitrogen Excellent for trapping applications, freeze drying, and rapidly cooling small volumes of liquids Operator's Manual
$2,144.00
Polyscience IP-100 Low Temperature Cooler, 3" Rigid Coil Probe
Polyscience IP-100 Low Temperature Cooler, 3" Rigid Coil Probe ***Note: This item has a lead time of 2-3 weeks depending on stock availability.*** Key Specifications Description Immersion Probe-100, 3" Rigid Coil Display Temperature Working Temperature Range °C -100° to -60° Working Temperature Range °F -148° to -76° Working Temperature Range °C -100° to -60° Temperature Control (°F) Fixed at -148° Temperature Control (°C) Fixed at -100°C Cleanable Air Filter Yes Display Temperature Maximum Ambient Temperature °F 86° Maximum Ambient Temperature °C 30° Overall Dimensions (L x W x H) (in) 20.1 x 15 x 22.3 in Overall Dimensions (L x W x H) (cm) 51.1 x 38.1 x 56.6 cm Refrigerant R404A & R508B Immersion Probe Type Rigid Coil Probe Diameter (inches) 3 Probe Diameter (cm) 7.62 Probe Length (inches) Coil: 9 / Exposed: 17 Probe Length (cm) Coil: 22.9 / Exposed: 43.2 Flexible Hose Diameter (inches) 2.83 Flexible Hose Diameter (cm) 7.14 Flexible Hose Length (feet) 6 Flexible Hose Length (m) 1.83 Shipping Weight (pounds) 162.0 Shipping Weight (kilograms) 73.5 Catalog Page Number 114-115 60 Hz Only Part Number P10N6A101B Cooling Capacity @ -100°C (W) 0 Cooling Capacity @ -80°C (W) 35 Cooling Capacity @ -65°C (W) 85 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/11.5 Key Features: Continuous cooling to temperatures as low as -100C Designed to run at maximum cooling An economical alternative to dry ice or liquid nitrogen Excellent for trapping applications, freeze drying, and rapidly cooling small volumes of liquids Operator's Manual
$6,091.00
LAUDA Ultracool UC 4 Circulation chiller 230 V; 50 Hz
LAUDA Ultracool UC 4 Circulation Chiller Features Process circulation chiller for industrial applications Suitable for operation at ambient temperatures from -15 °C to 50 °C 1-line LED display for display of actual or set temperature User-friendly menu guidance with simplest 2-key operation Electronic 2-point temperature control with hysteresis Safety elements for refrigerant pressure and tank level Protection level IP 54 (for outdoor installation) Industrial block pump with high pressure and high flow rate Evaporator and pump in stainless steel construction Integrated water filter and antibacterial additive for heat transfer liquid Start-up Systems for low ambient temperatures Antifreeze protection thermostat Integrated motor fan speed regulation Insulated water tank made of polyethylene Operation with refrigerant R 134a Versatile options available Options included Reinforced pump Product LAUDA Ultracool UC 4 Working temperature max. °C 25 Working temperature min. °C -5 Temperature stability ±K 2 Ambient temperature min. °C -15 Ambient temperature max. °C 50 Cooling output at 25 °C kW 6.9 Cooling output at 20 °C kW 6.9 Cooling output at 15 °C kW 5.9 Cooling output at 10 °C kW 4.9 Cooling output at 5 °C kW 4.1 Cooling output at 0 °C kW 3.4 Cooling output at -5 °C kW 2.8 Pump pressure max. bar 3.4 Pump flow max. L/min 42 Pump pressure nominal bar 2.8 Pump flow nominal L/min 13.8 Pump connection thread mm Rp 1/2 Volume water tank L 19 Dimensions (WxDxH) mm 640x640x635 Protection rating IP 44 Noise level dB (A) 50.4 Weight kg 85 Loading max. kW 1.8
$7,875.00
LAUDA Ultracool UC 24 Circulation chiller 400 V; 3/PE; 50 Hz
LAUDA Ultracool UC 24 Circulation Chiller Features Highly efficient industrial chiller LCD remote control with 8 m cable Operation possible via web server Electronic 2-point temperature control Protection level IP 54 (for outdoor installation) Industrial block pump with high pressure and high flow rate Integrated water filter Integrated Ethernet interface Inlet and outlet water connections in stainless steel Operates with non flammable liquids (water,water/glycol) Meeting the energy efficiency requirements of the EcoDesign directive 2009/125/EC Condenser cooling Air Options includedReinforced pump in stainless steel (5bar) Technical Features Working temperature range -10 ... 35 °C Ambient temperature range -15 ... 50 °C Temperature stability 0.5 ± K Filling volume max. 35 L Pump Pressure max. 5,8 bar Pump Pressure nominal 4.9 bar Pump flow rate max. (pressure) 200 L/min Pump flow rate nominal 84.1 L/min In / Outlet connection thread (inside) Rp 1 Overall dimensions (WxDxH) 720 x 910 x 1250 mm Weight 180 kg Noise level 64.7 dB(A) Refrigerant stage 1 R-410A (GWP 2088); 2.200 kg; 4.6 t CO2-eq SEPR 5.63 Power supply 400 V; 3/PE; 50 Hz Power plug ---
$26,015.00
LAUDA Ultracool UC 50 Circulation chiller 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz
LAUDA Ultracool UC 50 Circulation Chiller Features Highly efficient industrial chiller LCD remote control with 8 m cable Operation possible via web server Electronic 2-point temperature control Protection level IP 54 (for outdoor installation) Industrial block pump with high pressure and high flow rate Integrated water filter Integrated Ethernet interface Inlet and outlet water connections in stainless steel Operates with non flammable liquids (water,water/glycol) Meeting the energy efficiency requirements of the EcoDesign directive 2009/125/EC Condenser cooling Air Technical Features Working temperature range -10 ... 35 °C Ambient temperature range -15 ... 50 °C Temperature stability 0.5 ± K Filling volume max. 210 L Pump Pressure max. 4,6 bar (50 Hz), 6,8 bar (60 Hz) Pump Pressure nominal 3.3 bar (50 Hz); 5.5 bar (60 Hz) Pump flow rate max. (pressure) 230 L/min (50 Hz); 300 L/min (60 Hz) Pump flow rate nominal 150 L/min In / Outlet connection thread (inside) Rp 1 1/2 Overall dimensions (WxDxH) 1040 x 1435 x 1890 mm Weight 340 kg Noise level 68.7 dB(A) Refrigerant stage 1 R-410A (GWP 2088); 6.000 kg; 12.5 t CO2-eq SEPR 5.37 Power supply 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz Power plug --- Part Number: L002856 Temperature Cooling Capacity 50 Hz Cooling Capacity 60 Hz 25 °C 67.5 kW 67.5 kW 20 °C 65.6 kW 65.6 kW 15 °C 59.4 kW 59.4 kW 10 °C 51.2 kW 51.2 kW 5 °C 43.7 kW 43.7 kW 0 °C 36.4 kW 36.4 kW -5 °C 30.4 kW 30.4 kW -10 °C 25.2 kW 25.2 kW
$40,810.00
LAUDA Ultracool UC 65 Circulation chiller 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz
LAUDA Ultracool UC 65 Circulation Chiller Features Highly efficient industrial chiller LCD remote control with 8 m cable Operation possible via web server Electronic 2-point temperature control Protection level IP 54 (for outdoor installation) Industrial block pump with high pressure and high flow rate Integrated water filter Integrated Ethernet interface Inlet and outlet water connections in stainless steel Operates with non flammable liquids (water,water/glycol) Meeting the energy efficiency requirements of the EcoDesign directive 2009/125/EC Condenser cooling Air Technical Features Working temperature range -10 ... 35 °C Ambient temperature range -15 ... 50 °C Temperature stability 0.5 ± K Filling volume max. 210 L Pump Pressure max. 5,0 bar (50 Hz), 7,2 bar (60 Hz) Pump Pressure nominal 3.3 bar (50 Hz); 5.7 bar (60 Hz) Pump flow rate max. (pressure) 250 L/min (50 Hz); 300 L/min (60 Hz) Pump flow rate nominal 196 L/min In / Outlet connection thread (inside) Rp 1 1/2 Overall dimensions (WxDxH) 1040 x 1435 x 1890 mm Weight 440 kg Noise level 69.5 dB(A) Refrigerant stage 1 R-410A (GWP 2088); 6.000 kg; 12.5 t CO2-eq SEPR 5.16 Power supply 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz Power plug --- --> Part Number: L002857 Temperature Cooling Capacity 50 Hz Cooling Capacity 60 Hz 25 °C 87.5 kW 87.5 kW 20 °C 85.2 kW 85.2 kW 15 °C 77.4 kW 77.4 kW 10 °C 66.9 kW 66.9 kW 5 °C 57.3 kW 57.3 kW 0 °C 47.8 kW 47.8 kW -5 °C 40.1 kW 40.1 kW -10 °C 33.3 kW 33.3 kW
$49,185.00
LAUDA Integral IN 280 XT Process thermostat 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz
LAUDA Integral IN 280 XT Process thermostat Features Process thermostat with integrated cooling system for dynamic temperature control within external circuits Coloured TFT display for simultaneous indication of actual & set values and graphic illustration of the temperature profile Clear text menu navigation, six selectable languages DE, EN, FR, ES, IT, RU Management of heat transfer liquids with stored properties Easy input via cursor and soft keys. Additional Tmax key for overtemperature protection Self-Check Assistant for system diagnosis Fully electronic continuous controller with PID action for internal & external control Self adapt function for determination of control parameters Power Adapt system for the use of the maximum possible amount of heat permitted by the power supply system Low-level and adjustable over-temperature protection with acoustic alarm for use with flammable and non-flammable liquids Powerful LAUDA Variopump (pressure pump) with 8 selectable output levels or control of outflow pressure USB and Ethernet interface equipped as standard Port for external Pt100 integrated, second external Pt100 feasible via interface module Remote fault indication through floating contact Option for upgrading up to 2 additional interfaces (RS 232/485, Profibus, analogue, contact or EtherCAT module) Integrated and adjustable bypass Programmer with 150 temperature/time segments that can be separated into 5 programs Digital display of pump pressure Integrated web server for browser based operation in local area networks via PC, tablet or smart phone, secure data transfer due to authentication procedure and encryption Very small internal volume and big non-thermostated expansion vessel (cold fluid layer system) SmartCool system for energy-saving digital cooling management including compressor on-off control Condenser cooling Air Technical Features (according to DIN 12876) Working temperature range -80 ... 220 °C Ambient temperature range 5 ... 40 °C Temperature stability 0.05 ± K Heater power max. 4 kW Power consumption max. 9 kW Current max. 13.5 A Pump Pressure max. 3,1 bar Pump flow rate max. (pressure) 65 L/min In / Outlet connection thread (outside) M30 x 1,5 Inlet/outlet hose size 3/4″ Filling volume min. 4.8 L Filling volume max. 17.2 L Overall dimensions (WxDxH) 560 x 550 x 1325 mm Weight 198 kg Noise level 63 dB(A) Refrigerant stage 1 R-449A (GWP 1397); 0.800 kg; 1.1 t CO2-eq Refrigerant stage 2 R-23 (GWP 14800); 0.400 kg; 5.9 t CO2-eq Power supply 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz Power plug Power cord with plug (IEC 60309, 5-pol, CEE, red, 16 A) Temperature Pump stage Heat transfer liquid Cooling Capacity 50 Hz Cooling Capacity 60 Hz 200 °C 8 Thermal oil 1.6 kW 1.6 kW 100 °C 8 Thermal oil 1.6 kW 1.6 kW 20 °C 8 Ethanol 1.6 kW 1.6 kW 10 °C 8 Ethanol 1.55 kW 1.55 kW 0 °C 8 Ethanol 1.5 kW 1.5 kW -10 °C 8 Ethanol 1.5 kW 1.5 kW -20 °C 4 Ethanol 1.7 kW 1.7 kW -30 °C 4 Ethanol 1.7 kW 1.7 kW -40 °C 4 Ethanol 1.65 kW 1.65 kW -50 °C 4 Ethanol 1.4 kW 1.4 kW -60 °C 4 Ethanol 0.85 kW 0.85 kW -70 °C 4 Ethanol 0.35 kW 0.35 kW -80 °C 2 Ethanol 0.15 kW 0.15 kW
$54,220.00
LAUDA Integral IN 590 XTW Process thermostat 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz
LAUDA Integral IN 590 XTW Process thermostat Temperature Control For Processing Features Process thermostat with integrated cooling system for dynamic temperature control within external circuits Coloured TFT display for simultaneous indication of actual & set values and graphic illustration of the temperature profile Clear text menu navigation, six selectable languages DE, EN, FR, ES, IT, RU Management of heat transfer liquids with stored properties Easy input via cursor and soft keys. Additional Tmax key for overtemperature protection Self-Check Assistant for system diagnosis Fully electronic continuous controller with PID action for internal & external control Self adapt function for determination of control parameters PowerAdapt system for the use of the maximum possible amount of heat permitted by the power supply system Low-level and adjustable over-temperature protection with acoustic alarm for use with flammable and non-flammable liquids Powerful LAUDA Variopump (pressure pump) with 8 selectable output levels or control of outflow pressure USB and Ethernet interface equipped as standard Port for external Pt100 integrated, second external Pt100 feasible via interface module Remote fault indication through floating contact Option for upgrading up to 2 additional interfaces (RS 232/485, Profibus, analogue, contact or EtherCAT module) Integrated and adjustable bypass Programmer with 150 temperature/time segments that can be separated into 5 programs Digital display of pump pressure Very small internal volume and big non-thermostated expansion vessel (cold fluid layer system) Integrated web server for browser based operation in local area networks via PC, tablet or smart phone, secure data transfer due to authentication procedure and encryption SmartCool system for energy-saving digital cooling management including compressor on-off control Condenser cooling Water Technical Features Working temperature range -90 ... 220 °C Ambient temperature range 5 ... 40 °C Temperature stability 0.05 ± K Heater power max. 8 kW Power consumption max. 11 kW Current max. 16 A Pump Pressure max. 3,1 bar Pump flow rate max. (pressure) 65 L/min In / Outlet connection thread (outside) M30 x 1,5 Inlet/outlet hose size 3/4″ Filling volume min. 8 L Filling volume max. 28.6 L Water cooling connection thread (outside) 3/4 ″ Recommended cooling water temperature 15 °C Cooling water flow rate 15.8 L/min Recommended pressure difference cooling water 3 bar Pressure difference cooling water min. 0.8 bar Max. pressure difference cooling water 10 bar Maximal pressure cooling water 10 bar Overall dimensions (WxDxH) 760 x 650 x 1605 mm Weight 279 kg Noise level 64 dB(A) Refrigerant stage 1 R-449A (GWP 1397); 1.500 kg; 2.1 t CO2-eq Refrigerant stage 2 R-508B (GWP 13400); 1.200 kg; 16.1 t CO2-eq Power supply 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz Power plug Power cord with plug (IEC 60309, 5-pol, CEE, red, 16 A)
$94,310.00
LAUDA Integral IN 1590 XTW Process thermostat 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz
LAUDA Integral IN 1590 XTW Process thermostat Temperature Control For Processing Features Process thermostat with integrated cooling system for dynamic temperature control within external circuits Coloured TFT display for simultaneous indication of actual & set values and graphic illustration of the temperature profile Clear text menu navigation, six selectable languages DE, EN, FR, ES, IT, RU Management of heat transfer liquids with stored properties Easy input via cursor and soft keys. Additional Tmax key for overtemperature protection Self-Check Assistant for system diagnosis Fully electronic continuous controller with PID action for internal & external control Self adapt function for determination of control parameters PowerAdapt system for the use of the maximum possible amount of heat permitted by the power supply system Low-level and adjustable over-temperature protection with acoustic alarm for use with flammable and non-flammable liquids Powerful LAUDA Variopump (pressure pump) with 8 selectable output levels or control of outflow pressure USB and Ethernet interface equipped as standard Port for external Pt100 integrated, second external Pt100 feasible via interface module Remote fault indication through floating contact Option for upgrading up to 2 additional interfaces (RS 232/485, Profibus, analogue, contact or EtherCAT module) Integrated and adjustable bypass Programmer with 150 temperature/time segments that can be separated into 5 programs Digital display of pump pressure Very small internal volume and big non-thermostated expansion vessel (cold fluid layer system) Integrated web server for browser based operation in local area networks via PC, tablet or smart phone, secure data transfer due to authentication procedure and encryption SmartCool system for energy-saving digital cooling management including compressor on-off control Condenser cooling Water Technical Features Working temperature range -90 ... 220 °C Ambient temperature range 5 ... 40 °C Temperature stability 0.05 ± K Heater power max. 12 kW Power consumption max. 19 kW Current max. 25 A Pump Pressure max. 3,1 bar Pump flow rate max. (pressure) 65 L/min In / Outlet connection thread (outside) M38 x 1,5 Inlet/outlet hose size 1″ Filling volume min. 10 L Filling volume max. 30.6 L Water cooling connection thread (outside) 3/4 ″ Recommended cooling water temperature 15 °C Cooling water flow rate 26 L/min Recommended pressure difference cooling water 3 bar Pressure difference cooling water min. 0.8 bar Max. pressure difference cooling water 10 bar Maximal pressure cooling water 10 bar Overall dimensions (WxDxH) 760 x 650 x 1605 mm Weight 356 kg Noise level 65 dB(A) Refrigerant stage 1 R-449A (GWP 1397); 3.400 kg; 4.7 t CO2-eq Refrigerant stage 2 R-508B (GWP 13400); 1.800 kg; 24.1 t CO2-eq Power supply 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz Power plug Power cord with plug (IEC 60309, 5-pol, CEE, red, 32 A) Temperature Pump stage Heat transfer liquid Cooling Capacity 50 Hz Cooling Capacity 60 Hz 200 °C 8 Thermal oil 18.5 kW 18.5 kW 100 °C 8 Thermal oil 18.5 kW 18.5 kW 20 °C 8 Ethanol 18.5 kW 18.5 kW 10 °C 8 Ethanol 15 kW 16 kW 0 °C 8 Ethanol 11.5 kW 12.2 kW -10 °C 8 Ethanol 8.7 kW 9 kW -20 °C 4 Ethanol 8.5 kW 9 kW -30 °C 4 Ethanol 8.5 kW 9 kW -40 °C 4 Ethanol 7.5 kW 8.5 kW -50 °C 4 Ethanol 6 kW 7 kW -60 °C 4 Ethanol 4 kW 5.2 kW -70 °C 4 Ethanol 2.2 kW 3.4 kW -80 °C 4 Ethanol 0.9 kW 1.5 kW -90 °C 2 Ethanol 0.35 kW 0.5 kW
$112,200.00
HUBER CS Chillers
HUBER CS Chillers The new CS chillers expand the Huber product range with compact and highly affordable recirculating coolers. The Huber CS chillers combine cool and smart technology in one unit. The new chillers further reduce water consumption and lower the operating costs for many applications. The investment pays itself off after a short time because of the water savings and the low purchase price. Your advantages: Working temperature from -20 °C to +15 °C Cooling power up to 70 kW Pump performance up to 125 l/min Quiet operation less than 79 db Economic and ecological solution to eliminate costly water waste Easy to use and maintenance free With a cooling power up to 70 kW, the devices are particularly suited for constant temperature control for laboratory applications, e.g. for cooling vacuum pumps, rotary evaporators, electron microscopy, AAS-devices, ICP-devices, extraction, distillation and many more. Sku Model Temperature Range Pump Vapacity Max/Pump Connection Cooling power(kW) at (°C) HeatingPower NoiseLevel Dimensions Voltage Data Sheet (°C) (l/min) (bar) 15 10 0 -10 -20 (kW) (dB) W x D x H (inch) PDF VDH1100664 CS 25 -20...15 50 4.5 1/2" 3.5 2.5 1.6 0.98 0.7 - 60 22.8 x 26.0 x 32.3 208V 2~ 60Hz VDH1101336 CS 35 -20...15 30 4.0 1/2" 4.0 3.5 2.1 2.0 0.8 62 22.8 x 26.0 x 32.3 208V 2~ 60Hz VDH1100689 CS 50 -20...15 83 4.0 3/4" 8 5 4.2 3.5 2 - 63 26.8 x 28.7 x 59.8 460V 3~ 60Hz VDH4100126 CS 50-H -20...85 83 3.7 3/4" 8 5 4.2 3.5 2 2.8 63 26.8 x 28.7 x 59.8 460V 3~ 60Hz VDH1100690 CS 100 -20...15 83 4.0 3/4" 18 10 9.5 7.5 4.5 - 70 31.5 x 33.5 x 65.6 460V 3~ 60Hz VDH4100106 CS 100-H -20...85 83 3.7 3/4" 18 10 9.5 7.5 4.5 5.5 70 31.5 x 33.5 x 65.6 460V 3~ 60Hz VDH1100688 CS 200 -20...15 125 4.2 1" 28 20 18 15 9.5 - 78 55.1 x 39.4 x 70.9 460V 3~ 60Hz VDH4100091 CS 200-H -20...85 125 4.2 1" 28 20 18 15 9.5 5.5 78 55.1 x 39.4 x 70.9 460V 3~ 60Hz
$14,700.00 - $54,400.00
HUBER Unistat T305 with Pilot ONE
HUBER Unistat T305 with Pilot ONE (Please Note: There is a 2 - 3 weeks lead time) The Unistat range inspires with unique thermodynamic properties and a range of functions to meet the highest demands. Unistat technology guarantees precise, reproducible temperature control results, the shortest possible heating and cooling times and large temperature ranges without the need for fluid change. All Unistats are fitted with the innovative Because Unistats are hydraulically sealed, the service life of the temperature control fluid is dramatically increased by preventing oil loss through vapours and oxidation, further saving resources. Unistats are fitted with extensive safety equipment and are therefore suitable for unsupervised continuous operation. Relevant operating conditions are constantly monitored and the system is switched off if necessary or with the process safety feature the emergency cooling circuit is activated. Data sheet 3 Year Warranty Extension General Information & Temperature Controller Temperature range 65...300 °C Temperature stability ±0,02 °C Temperature control TAC, self-optimizing (True Adaptive Control) Controller Pilot ONE (E-grade "Basic") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 425 x 250 x 631 mm | 16.73 x 9.84 x 24.84 inches Weight 37 kg | 81.59 pounds Heating / Cooling Capacity Heating capacity 4,8 kW Circulation Pump Pressure pump max. 45 lpm ; 0.9 bar | 11.89 gpm ; 13.05 psi Pump connection M24x1,5 AG male Permissible viscosity 50 mm²/s Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating Data Old sku 1003.0022.01 Permissible ambient temp. 5 to 40 °C Filling volume min. 1.45 Liters | 0.38 gal Volume of expansion 2.8 Liters | 0.74 gal Power supply 208V 3~ 60Hz Current max. 15 A Fusing 15,5 A
$22,800.00 - $23,300.00
Huber Unistat T330 with Pilot ONE
Huber Unistat T330 with Pilot ONE The Unistat range inspires with unique thermodynamic properties and a range of functions to meet the highest demands. Unistat technology guarantees precise, reproducible temperature control results, the shortest possible heating and cooling times and large temperature ranges without the need for fluid change. All Unistats are fitted with the innovative Pilot ONE controller with a 5.7“ touchscreen colour display and easy menu navigation. All important parameters can be seen at a glance and temperature curves are displayed in graphic real time. Unistats are equipped with the most up-to-date pump technology for optimal heat transfer. The pump self regulates to ensure the best possible circulation and flow and delicate glass reactors are protected from breakage by the pumps soft start-up feature. Unistat technology impresses as a result of economic operation with reduced operating costs and efficient energy management. Because Unistats are hydraulically sealed, the service life of the temperature control fluid is dramatically increased by preventing oil loss through vapours and oxidation, further saving resources. Unistats are fitted with extensive safety equipment and are therefore suitable for unsupervised continuous operation. Relevant operating conditions are constantly monitored and the system is switched off if necessary or with the process safety feature the emergency cooling circuit is activated. General information & temperature controller Temperature range 65...300 °C Temperature stability ±0,01 °C Temperature control TAC, self-optimizing (True Adaptive Control) Display resolution 0,01 °C Alarm message optical, acoustical Controller Pilot ONE (E-grade "Professional") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 540 x 678 x 1174 mm Weight -- kg Heating / cooling capacity Heating capacity 21 - 24 kW Circulation pump Pressure pump max. 96 l/min ; 3,5 bar Pump connection M30x1,5 AG male Permissible viscosity 50 mm²/s Pump speed adjustable Yes Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating data Permissible ambient temp. 5...40 °C Volume of expansion 24 Litres Power supply 380-460V 3~ 50/60Hz
$54,050.00
Huber Unistat 520w with Pilot ONE
Huber Unistat 520w with Pilot ONE (Please Note: There is a shipping lead time of 2 - 3 weeks) he Unistat range inspires with unique thermodynamic properties and a range of functions to meet the highest demands. Unistat technology guarantees precise, reproducible temperature control results, the shortest possible heating and cooling times and large temperature ranges without the need for fluid change. All Unistats are fitted with the innovative Pilot ONE controller with a 5.7“ touchscreen colour display and easy menu navigation. All important parameters can be seen at a glance and temperature curves are displayed in graphic real time. Unistats are equipped with the most up-to-date pump technology for optimal heat transfer. The pump self regulates to ensure the best possible circulation and flow and delicate glass reactors are protected from breakage by the pumps soft start-up feature. Unistat technology impresses as a result of economic operation with reduced operating costs and efficient energy management. Because Unistats are hydraulically sealed, the service life of the temperature control fluid is dramatically increased by preventing oil loss through vapours and oxidation, further saving resources. Unistats are fitted with extensive safety equipment and are therefore suitable for unsupervised continuous operation. Relevant operating conditions are constantly monitored and the system is switched off if necessary or with the process safety feature the emergency cooling circuit is activated. The new multi-touch controller Pilot ONE offers a brilliant 5.7" touchscreen with graphic functions and a comfortable navigation menu. All important operating parameters and temperature values are neatly displayed on the touchscreen. Thanks to the new favourites menu, the one-click operation and the integrated technical glossary the operation is very easy, just like on a smartphone. Integrated USB and Ethernet ports allows connection to a PC or network, e.g. for remote control or data transmission. Data Sheet 3 Years Warranty Extension Operating manuals General information & temperature controller Temperature range -55...250 °C Temperature stability ±0.01 °C Temperature control TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C Alarm message optical, acoustical Controller Pilot ONE (E-grade "professional") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 540 x 604 x 1332 mm | 21.26 x 23.78 x 52.44 inches Weight 212 kg | 467.46 pounds Heating / cooling capacity Heating capacity 9 kW Cooling capacity 250 200 100 20 0 -20 -40 -50 °C 6 6 6 6 6 1,2 0,65 kW 250 200 Cooling machine water-cooled Refrigerant (ASHRAE, GHS) R452A (A1, H280) (1,44 kg) Circulation pump Pressure pump max. 79 lpm ; 1.5 bar | 20.87 gpm ; 21.75 psi Pump connection M30x1,5 AG male Permissible viscosity 50 mm²/s Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating data Permissible ambient temp. 5...40 °C Noise level 61 dB(A) Filling volume min. 4.9 Liters | 1.29 gal Volume of expansion 16 Liters | 4.23 gal Cooling water connection G1/2 AG Cooling water differential pressure min. 1 bar | 14.5 psi Cooling water pressure max. 6 bar | 87 psi Power supply 460V 3~ 60Hz Current max. 13 A
$59,900.00 - $60,400.00
HUBER Unistat 815 Dynamic Temperature Control / Circulation Thermostat
HUBER Unistat 815 Dynamic Temperature Control (Please Note: There is a 2 - 3 weeks lead time) Unistat Circulators are an ideal solution for fast and precise thermal control of externally connected applications. These systems offer rapid temperature change and a wide temperature range without having to change fluid. The new Pilot ONE controller features a navigation system with easily remembered icons and menus which are sorted by color to make routine work simpler. An amazing software guides you through your set up ensuring all the necessary settings are correct. Unistat 815 208V Data sheet Unistat 815 460V Data sheet 3 Year Warranty Extension General Information & Temperature Controller Unistat 815208V Unistat 815460V Temperature range -85...250 °C -85...250 Temperature stability ±0.01 °C ±0.01 Temperature control TAC, self-optimizing (True Adaptive Control) TAC, self-optimizing (True Adaptive Control) Alarm message optical, acoustical optical, acoustical Controller Pilot ONE (E-grade "Professional") Pilot ONE (E-grade "Professional") Safety class III / FL III / FL Protection class IP20 IP20 Dimensions (W x D x H) 18.11 x 23.78 x 65.55 inches 18.11 x 23.78 x 57.68 inches Weight 331 kg | 729.86 pounds 229 kg | 504.94 pounds Heating / Cooling Capacity Heating capacity 2 kW 2,6 kW Cooling machine air-cooled air-cooled Refrigerant 1. stage R452A (A1, H280) (1,8 kg) R452A (A1, H280) (1,8 kg) Refrigerant 2. stage R23 (A1, H280) (0,39 kg) R23 (A1, H280) (0,39 kg) Circulation Pump Pressure pump max. 40 lpm ; 0.9 bar | 10.57 gpm ; 13.05 psi 40 lpm ; 0.9 bar | 10.57 gpm ; 13.05 psi Pump connection M30x1,5 AG male M30x1,5 AG male Permissible viscosity 50 mm²/s 50 mm²/s Connections Pt100 connection Pt100 Pt100 Digital interface RS232, Ethernet, USB Device, USB Host RS232, Ethernet, USB Device, USB Host Analogue input via optional Com.G@te via optional Com.G@te Analogue output via optional Com.G@te via optional Com.G@te Operating Data Old Sku 1014.0054.01 1014.0055.01 Permissible ambient temp. 5 to 40 °C 5 to 40 °C Noise Level 64 dB(A) 64 dB(A) Filling volume min. 3.8 Liters / 1 gal 3.8 Liters / 1 gal Volume of expansion 3.3 Liters / 0.87 gal 3.3 Liters / 0.87 gal Power supply 208V 3~ 60Hz 460V 3~ 60Hz Current max 21,5 A 11 A
$55,550.00 - $63,250.00
HUBER Unistat 825 Dynamic Temperature Control / Circulation Thermostat
HUBER Unistat 825 Dynamic Temperature Control (Please Note: There is a 2 weeks Shipping lead time) Unistat Circulators are an ideal solution for fast and precise thermal control of externally connected applications. These systems offer rapid temperature change and a wide temperature range without having to change fluid. The new Pilot ONE controller features a navigation system with easily remembered icons and menus which are sorted by color to make routine work simpler. An amazing software guides you through your set up ensuring all the necessary settings are correct. General Information & Temperature Controller Unistat 825208V Unistat 825460V Temperature range -85...250 °C -85...250 Temperature stability ±0.01 °C ±0.01 Temperature control TAC, self-optimizing (True Adaptive Control) TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C 0.01 °C Alarm message optical, acoustical optical, acoustical Controller Pilot ONE (E-grade "Professional") Pilot ONE (E-grade "Professional") Safety class III / FL III / FL Protection class IP20 IP20 Dimensions (W x D x H) 18.11 x 23.78 x 65.55 inches 18.11 x 23.78 x 57.68 inches Weight 696.78 Lb 487.3 Lb Heating / Cooling Capacity Heating capacity 3 kW 4 kW Cooling machine air-cooled air-cooled Refrigerant 1. stage R507 (1,8 kg) R507 (1,8 kg) Refrigerant 2. stage R23 R23 Circulation Pump Pressure pump max. 10.57 gpm ; 13.05 psi 10.57 gpm ; 13.05 psi Pump connection M30x1,5 AG male M30x1,5 AG male Permissible viscosity 50 mm²/s 50 mm²/s Connections Pt100 connection Pt100 Pt100 Digital interface RS232, Ethernet, USB Device, USB Host RS232, Ethernet, USB Device, USB Host Operating Data Permissible ambient temp. 5 to 40 °C 5 to 40 °C Noise level 64 dB(A) 64 dB(A) Filling volume min. 2.9 Liters / 0.77 gal 2.9 Liters / 0.77 gal Volume of expansion 3.6 Liters / 0.95 gal 3.6 Liters / 0.95 gal Power supply 208V 3~ 60Hz 460V 3~ 60Hz Current max 20 A 14,5 A
$79,350.00 - $87,400.00
HUBER Unistat 905 Dynamic Temperature Control / Circulation Thermostat
HUBER Unistat 905 Dynamic Temperature Control (Please Note: There is 8 week shipping lead time) Disclaimer: This item is Non-Refundable once ordered. Unistat Circulators are an ideal solution for fast and precise thermal control of externally connected applications. These systems offer rapid temperature change and a wide temperature range without having to change fluid. The new Pilot ONE controller features a navigation system with easily remembered icons and menus which are sorted by color to make routine work simpler. An amazing software guides you through your set up ensuring all the necessary settings are correct. Unistat 905 208V Data sheet Unistat 905 460V Data sheet General Information & Temperature Controller Unistat 905 208V Unistat 905 460V Temperature range -90 to 250 °C -90 to 250 °C Temperature stability ±0.01 °C ±0.01 Temperature control TAC, self-optimizing (True Adaptive Control) TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C 0.01 °C Alarm message optical, acoustical optical, acoustical Controller Pilot ONE (E-grade "Professional") Pilot ONE (E-grade "Professional") Safety class III / FL III / FL Protection class IP20 IP20 Dimensions (W x D x H) 540 x 654 x 1738 mm | 21.26 x 25.75 x 68.43 inches 540 x 654 x 1500 mm | 21.26 x 25.75 x 59.06 inches Weight 396 kg | 873.18 pounds 275 kg | 606.38 pounds Heating / Cooling Capacity Heating capacity 6 kW 6 kW Cooling machine air-cooled air-cooled Refrigerant 1. stage R452A (A1, H280) (2,5 kg) R452A (A1, H280) (2,5 kg) Refrigerant 2. stage R23 (A1, H280) (0,75 kg) R23 Circulation Pump Pressure pump max. 48 lpm ; 0.9 bar | 12.68 gpm ; 13.05 psi 10.57 gpm ; 13.05 psi Pump connection M30x1,5 AG male M30x1,5 AG male Permissible viscosity 50 mm²/s 50 mm²/s Connections Pt100 connection Pt100 Pt100 Analogue input via optional Com.G@te via optional Com.G@te Analogue output via optional Com.G@te via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host RS232, Ethernet, USB Device, USB Host Operating Data Old sku 1035.0013.01 1035.0014.01 Permissible ambient temp. 5...35 °C 5...35 °C Filling volume min. 3.2 Liters | 0.85 gal 3.2 Liters | 0.85 gal Volume of expansion 5.3 Liters | 1.4 gal 5.3 Liters | 1.4 gal Power supply 208V 3~ 60Hz 460V 3~ 60Hz Current max 40 A 23,5 A
$101,900.00 - $113,800.00
Huber Unistat 915w with Pilot ONE
Huber Unistat 915w with Pilot ONE (Please Note: There is a 2 - 3 weeks lead time) Unistat Circulators are an ideal solution for fast and precise thermal control of externally connected applications. These systems offer rapid temperature change and a wide temperature range without having to change fluid. The new Pilot ONE controller features a navigation system with easily remembered icons and menus which are sorted by color to make routine work simpler. An amazing software guides you through your set up ensuring all the necessary settings are correct. Precise and reproducible temperature control results Fastest heating and cooling rate Wide temperature ranges with no fluid change Pilot ONE controller with 5.7“ touchscreen and comfortable menu navigation Adaptive temperature control, self-optimising Efficient circulation pump Data communication via LAN, internet, USB, RS232 and RS485 Efficient operation saves working time and operating costs Proven functionality for the process industry E-grade "Professional" included Download Data Sheet Click Here for 3 Year Warranty Online Registration Download Operating Manual General information & Temperature Controller Temperature range -90...250 °C Temperature stability ±0.02 °C ±0.01 °C Temperature control TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C Alarm message optical, acoustical Controller Pilot ONE (E-grade "Professional") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 630 x 704 x 1565 mm | 24.8 x 27.72 x 61.61 inches Weight 364 kg | 802.62 pounds Heating / Cooling Capacity Heating capacity 6 kW Cooling capacity 250 200 100 0 -20 -40 -60 -80 -90 °C 6,5 7,5 9 11 11 11 8,2 4,2 1,3 0,6 kW Cooling machine water-cooled Refrigerant 1. stage R507 (A1, H280) (2,9 kg) Refrigerant 2. stage R23 (A1, H280) (1,23 kg) Circulation Pump Pressure pump max. 110 lpm ; 1.5 bar | 29.06 gpm ; 21.75 psi Pump Connection M30x1,5 AG male Permissible viscosity 50 mm²/s Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating Data Old sku 1055.0011.01 Permissible ambient temp. 5...40 °C Noise level 64 dB(A) Filling volume min. 3.9 Liters | 1.03 gal Volume of expansion 6.5 Liters | 1.72 gal Cooling water connection G3/4 AG Cooling water differential pressure min. 1 bar | 14.5 psi Cooling water pressure max. 6 bar | 87 psi Power supply 460V 3~ 60Hz Current max. 29 A
$131,900.00 - $132,400.00
You have seen 48 out of 187 products