Process Heaters

Express Extractor Heater by BVV™ 1 Year Warranty, Built in house ready to ship in 24hrs! The BVV™ Extractor Heater is our built in house high power extractor heater circulator.  We have 3 model units 3,500, 8,000 & 11,000 WATTS!  Each upright panel comes with 25ft of silicone tubing and a 5 gallon reservoir.  Each system is capable of heating up to 140°F and can exceed the demand of even the largest extraction vessels.  The system operates on an independent nitrile diaphragm pump circulating water @1.5GPM.  The pump can self prime up to 11ft. and within a typical extractor this pump is operating around 30-50psi in circulating pressure.     BVV Part# KW AMPS Voltage Breaker AMPS Installed Plug Rec. Wire Size Temp. Range EEH-3.5KW 3.5 29 120V (1x30)A L5-30P Plug 10 AWG 120°F EEH-8KW 7.3 33 240V (1x40)A 6-50P 8 AWG 80-140°F (adjustable) EEH-11KW 11 46 240V (2x30)A 6-30P (2x12) AWG 80-140°F (adjustable) EEH-5.5KW 5.5 25 220V (1X25)A 6-30P  10 AWG     The 3.5KW unit has a digital temperature display and cannot be adjusted from the standard factory programmed 120°F.  During normal recovery operations used with our extractors this fluctuates between 120-157°F.   Though there is a lack in temperature accuracy we measure at the extractor base a consistent recovery temperature around 122-125°F. These heater are built with an electrical failsafe that prevents them from operating dry, and will auto shut down if the flow is unexpectedly stopped to protect the unit.  The attached in-line filter will prevent any debris from entering the heater.  A clogged filter will also prevent the heater from operating.     General Extractor Size Heater Recommendations for these Models 0-2lbs Biomass EEH-3.5KW 2-5lbs Biomass EEH-8KW 5-20lbs Biomass EEH-11KW      At BVV our favorite model is the 11KW.  The unit does require two 240V 30A Single phase circuits, but its now a permanent fixture in or laboratory.   Every model will pump out lots of heat for any recovery situation, could you use a 3.5KW heater on a 5 or 10lb unit?  Absolutely, Just expect longer times to reach the heaters maximum setting.   For example we heated 3x 6"x48" fully jacketed columns to 140°F (heater temp) in about 11 minutes using the 11KW heater.   Another example is a 1lb Apollo extractor with a fully jacketed collection base heated to 120°F in about 8-9 min. using the 3.5KW extractor heater.    ETL Listed to UL 499 and CSA (Canada) Utilizing all UL approved components for the heater, pump, and emergency stop switches, wiring harnesses, plugs, and electrical housings.  The heater arrive with the specified plugs attached, however all of the models can be hardwired directly if you choose not to use a plug.  *240V units can be used on 208V single phase with 25% reduced temperature output Express Extractor Heater Quick Start Guide

Read more less

LAUDA Integral IN 280 XT Process thermostat   Features Process thermostat with integrated cooling system for dynamic temperature control within external circuits Coloured TFT display for simultaneous indication of actual & set values and graphic illustration of the temperature profile Clear text menu navigation, six selectable languages DE, EN, FR, ES, IT, RU Management of heat transfer liquids with stored properties Easy input via cursor and soft keys. Additional Tmax key for overtemperature protection Self-Check Assistant for system diagnosis Fully electronic continuous controller with PID action for internal & external control Self adapt function for determination of control parameters Power Adapt system for the use of the maximum possible amount of heat permitted by the power supply system Low-level and adjustable over-temperature protection with acoustic alarm for use with flammable and non-flammable liquids Powerful LAUDA Variopump (pressure pump) with 8 selectable output levels or control of outflow pressure USB and Ethernet interface equipped as standard Port for external Pt100 integrated, second external Pt100 feasible via interface module Remote fault indication through floating contact Option for upgrading up to 2 additional interfaces (RS 232/485, Profibus, analogue, contact or EtherCAT module) Integrated and adjustable bypass Programmer with 150 temperature/time segments that can be separated into 5 programs Digital display of pump pressure Integrated web server for browser based operation in local area networks via PC, tablet or smart phone, secure data transfer due to authentication procedure and encryption Very small internal volume and big non-thermostated expansion vessel (cold fluid layer system) SmartCool system for energy-saving digital cooling management including compressor on-off control Condenser cooling Air   Technical Features (according to DIN 12876) Working temperature range -80 ... 220 °C Ambient temperature range 5 ... 40 °C Temperature stability 0.05 ± K Heater power max. 4 kW Power consumption max. 9 kW Current max. 13.5 A Pump Pressure max. 3,1 bar Pump flow rate max. (pressure) 65 L/min In / Outlet connection thread (outside) M30 x 1,5 Inlet/outlet hose size 3/4″ Filling volume min. 4.8 L Filling volume max. 17.2 L Overall dimensions (WxDxH) 560 x 550 x 1325 mm Weight 198 kg Noise level 63 dB(A) Refrigerant stage 1 R-449A (GWP 1397); 0.800 kg; 1.1 t CO2-eq Refrigerant stage 2 R-23 (GWP 14800); 0.400 kg; 5.9 t CO2-eq Power supply 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz Power plug Power cord with plug (IEC 60309, 5-pol, CEE, red, 16 A)       Temperature Pump stage Heat transfer liquid Cooling Capacity 50 Hz Cooling Capacity 60 Hz 200 °C 8 Thermal oil 1.6 kW 1.6 kW 100 °C 8 Thermal oil 1.6 kW 1.6 kW 20 °C 8 Ethanol 1.6 kW 1.6 kW 10 °C 8 Ethanol 1.55 kW 1.55 kW 0 °C 8 Ethanol 1.5 kW 1.5 kW -10 °C 8 Ethanol 1.5 kW 1.5 kW -20 °C 4 Ethanol 1.7 kW 1.7 kW -30 °C 4 Ethanol 1.7 kW 1.7 kW -40 °C 4 Ethanol 1.65 kW 1.65 kW -50 °C 4 Ethanol 1.4 kW 1.4 kW -60 °C 4 Ethanol 0.85 kW 0.85 kW -70 °C 4 Ethanol 0.35 kW 0.35 kW -80 °C 2 Ethanol 0.15 kW 0.15 kW

Read more less

  LAUDA Integral IN 590 XTW Process thermostat   Temperature Control For Processing  Features Process thermostat with integrated cooling system for dynamic temperature control within external circuits Coloured TFT display for simultaneous indication of actual & set values and graphic illustration of the temperature profile Clear text menu navigation, six selectable languages DE, EN, FR, ES, IT, RU Management of heat transfer liquids with stored properties Easy input via cursor and soft keys. Additional Tmax key for overtemperature protection Self-Check Assistant for system diagnosis Fully electronic continuous controller with PID action for internal & external control Self adapt function for determination of control parameters PowerAdapt system for the use of the maximum possible amount of heat permitted by the power supply system Low-level and adjustable over-temperature protection with acoustic alarm for use with flammable and non-flammable liquids Powerful LAUDA Variopump (pressure pump) with 8 selectable output levels or control of outflow pressure USB and Ethernet interface equipped as standard Port for external Pt100 integrated, second external Pt100 feasible via interface module Remote fault indication through floating contact Option for upgrading up to 2 additional interfaces (RS 232/485, Profibus, analogue, contact or EtherCAT module) Integrated and adjustable bypass Programmer with 150 temperature/time segments that can be separated into 5 programs Digital display of pump pressure Very small internal volume and big non-thermostated expansion vessel (cold fluid layer system) Integrated web server for browser based operation in local area networks via PC, tablet or smart phone, secure data transfer due to authentication procedure and encryption SmartCool system for energy-saving digital cooling management including compressor on-off control Condenser cooling Water     Technical Features Working temperature range -90 ... 220 °C Ambient temperature range 5 ... 40 °C Temperature stability 0.05 ± K Heater power max. 8 kW Power consumption max. 11 kW Current max. 16 A Pump Pressure max. 3,1 bar Pump flow rate max. (pressure) 65 L/min In / Outlet connection thread (outside) M30 x 1,5 Inlet/outlet hose size 3/4″ Filling volume min. 8 L Filling volume max. 28.6 L Water cooling connection thread (outside) 3/4 ″ Recommended cooling water temperature 15 °C Cooling water flow rate 15.8 L/min Recommended pressure difference cooling water 3 bar Pressure difference cooling water min. 0.8 bar Max. pressure difference cooling water 10 bar Maximal pressure cooling water 10 bar Overall dimensions (WxDxH) 760 x 650 x 1605 mm Weight 279 kg Noise level 64 dB(A) Refrigerant stage 1 R-449A (GWP 1397); 1.500 kg; 2.1 t CO2-eq Refrigerant stage 2 R-508B (GWP 13400); 1.200 kg; 16.1 t CO2-eq Power supply 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz Power plug Power cord with plug (IEC 60309, 5-pol, CEE, red, 16 A)

Read more less

LAUDA Integral IN 1590 XTW Process thermostat  Temperature Control For Processing  Features Process thermostat with integrated cooling system for dynamic temperature control within external circuits Coloured TFT display for simultaneous indication of actual & set values and graphic illustration of the temperature profile Clear text menu navigation, six selectable languages DE, EN, FR, ES, IT, RU Management of heat transfer liquids with stored properties Easy input via cursor and soft keys. Additional Tmax key for overtemperature protection Self-Check Assistant for system diagnosis Fully electronic continuous controller with PID action for internal & external control Self adapt function for determination of control parameters PowerAdapt system for the use of the maximum possible amount of heat permitted by the power supply system Low-level and adjustable over-temperature protection with acoustic alarm for use with flammable and non-flammable liquids Powerful LAUDA Variopump (pressure pump) with 8 selectable output levels or control of outflow pressure USB and Ethernet interface equipped as standard Port for external Pt100 integrated, second external Pt100 feasible via interface module Remote fault indication through floating contact Option for upgrading up to 2 additional interfaces (RS 232/485, Profibus, analogue, contact or EtherCAT module) Integrated and adjustable bypass Programmer with 150 temperature/time segments that can be separated into 5 programs Digital display of pump pressure Very small internal volume and big non-thermostated expansion vessel (cold fluid layer system) Integrated web server for browser based operation in local area networks via PC, tablet or smart phone, secure data transfer due to authentication procedure and encryption SmartCool system for energy-saving digital cooling management including compressor on-off control Condenser cooling Water     Technical Features Working temperature range -90 ... 220 °C Ambient temperature range 5 ... 40 °C Temperature stability 0.05 ± K Heater power max. 12 kW Power consumption max. 19 kW Current max. 25 A Pump Pressure max. 3,1 bar Pump flow rate max. (pressure) 65 L/min In / Outlet connection thread (outside) M38 x 1,5 Inlet/outlet hose size 1″ Filling volume min. 10 L Filling volume max. 30.6 L Water cooling connection thread (outside) 3/4 ″ Recommended cooling water temperature 15 °C Cooling water flow rate 26 L/min Recommended pressure difference cooling water 3 bar Pressure difference cooling water min. 0.8 bar Max. pressure difference cooling water 10 bar Maximal pressure cooling water 10 bar Overall dimensions (WxDxH) 760 x 650 x 1605 mm Weight 356 kg Noise level 65 dB(A) Refrigerant stage 1 R-449A (GWP 1397); 3.400 kg; 4.7 t CO2-eq Refrigerant stage 2 R-508B (GWP 13400); 1.800 kg; 24.1 t CO2-eq Power supply 400 V; 3/PE; 50 Hz & 460 V; 3/PE; 60 Hz Power plug Power cord with plug (IEC 60309, 5-pol, CEE, red, 32 A)       Temperature Pump stage Heat transfer liquid Cooling Capacity 50 Hz Cooling Capacity 60 Hz 200 °C 8 Thermal oil 18.5 kW 18.5 kW 100 °C 8 Thermal oil 18.5 kW 18.5 kW 20 °C 8 Ethanol 18.5 kW 18.5 kW 10 °C 8 Ethanol 15 kW 16 kW 0 °C 8 Ethanol 11.5 kW 12.2 kW -10 °C 8 Ethanol 8.7 kW 9 kW -20 °C 4 Ethanol 8.5 kW 9 kW -30 °C 4 Ethanol 8.5 kW 9 kW -40 °C 4 Ethanol 7.5 kW 8.5 kW -50 °C 4 Ethanol 6 kW 7 kW -60 °C 4 Ethanol 4 kW 5.2 kW -70 °C 4 Ethanol 2.2 kW 3.4 kW -80 °C 4 Ethanol 0.9 kW 1.5 kW -90 °C 2 Ethanol 0.35 kW 0.5 kW

Read more less

HUBER Unistat T305 with Pilot ONE (Please Note: There is a 2 - 3 weeks lead time) The Unistat range inspires with unique thermodynamic properties and a range of functions to meet the highest demands. Unistat technology guarantees precise, reproducible temperature control results, the shortest possible heating and cooling times and large temperature ranges without the need for fluid change. All Unistats are fitted with the innovative   Because Unistats are hydraulically sealed, the service life of the temperature control fluid is dramatically increased by preventing oil loss through vapours and oxidation, further saving resources. Unistats are fitted with extensive safety equipment and are therefore suitable for unsupervised continuous operation. Relevant operating conditions are constantly monitored and the system is switched off if necessary or with the process safety feature the emergency cooling circuit is activated.   Data sheet  3 Year Warranty Extension    General Information & Temperature Controller Temperature range 65...300 °C Temperature stability ±0,02 °C Temperature control TAC, self-optimizing (True Adaptive Control) Controller Pilot ONE (E-grade "Basic") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 425 x 250 x 631 mm | 16.73 x 9.84 x 24.84 inches Weight 37 kg | 81.59 pounds Heating / Cooling Capacity Heating capacity 4,8 kW Circulation Pump Pressure pump max. 45 lpm ; 0.9 bar | 11.89 gpm ; 13.05 psi Pump connection M24x1,5 AG male Permissible viscosity 50 mm²/s Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating Data Old sku 1003.0022.01 Permissible ambient temp. 5 to 40 °C Filling volume min. 1.45 Liters | 0.38 gal Volume of expansion 2.8 Liters | 0.74 gal Power supply 208V 3~ 60Hz Current max. 15 A Fusing 15,5 A

Read more less

Huber Unistat T330 with Pilot ONE   The Unistat range inspires with unique thermodynamic properties and a range of functions to meet the highest demands. Unistat technology guarantees precise, reproducible temperature control results, the shortest possible heating and cooling times and large temperature ranges without the need for fluid change. All Unistats are fitted with the innovative Pilot ONE controller with a 5.7“ touchscreen colour display and easy menu navigation. All important parameters can be seen at a glance and temperature curves are displayed in graphic real time. Unistats are equipped with the most up-to-date pump technology for optimal heat transfer. The pump self regulates to ensure the best possible circulation and flow and delicate glass reactors are protected from breakage by the pumps soft start-up feature. Unistat technology impresses as a result of economic operation with reduced operating costs and efficient energy management. Because Unistats are hydraulically sealed, the service life of the temperature control fluid is dramatically increased by preventing oil loss through vapours and oxidation, further saving resources. Unistats are fitted with extensive safety equipment and are therefore suitable for unsupervised continuous operation. Relevant operating conditions are constantly monitored and the system is switched off if necessary or with the process safety feature the emergency cooling circuit is activated.       General information & temperature controller Temperature range 65...300 °C Temperature stability ±0,01 °C Temperature control TAC, self-optimizing (True Adaptive Control) Display resolution 0,01 °C Alarm message optical, acoustical Controller Pilot ONE (E-grade "Professional") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 540 x 678 x 1174 mm Weight -- kg Heating / cooling capacity Heating capacity 21 - 24 kW Circulation pump Pressure pump max. 96 l/min ; 3,5 bar Pump connection M30x1,5 AG male Permissible viscosity 50 mm²/s Pump speed adjustable Yes Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating data Permissible ambient temp. 5...40 °C Volume of expansion 24 Litres Power supply 380-460V 3~ 50/60Hz

Read more less

Huber Unistat 520w with Pilot ONE (Please Note: There is a shipping lead time of 2 - 3 weeks)   he Unistat range inspires with unique thermodynamic properties and a range of functions to meet the highest demands. Unistat technology guarantees precise, reproducible temperature control results, the shortest possible heating and cooling times and large temperature ranges without the need for fluid change. All Unistats are fitted with the innovative Pilot ONE controller with a 5.7“ touchscreen colour display and easy menu navigation. All important parameters can be seen at a glance and temperature curves are displayed in graphic real time. Unistats are equipped with the most up-to-date pump technology for optimal heat transfer. The pump self regulates to ensure the best possible circulation and flow and delicate glass reactors are protected from breakage by the pumps soft start-up feature. Unistat technology impresses as a result of economic operation with reduced operating costs and efficient energy management. Because Unistats are hydraulically sealed, the service life of the temperature control fluid is dramatically increased by preventing oil loss through vapours and oxidation, further saving resources. Unistats are fitted with extensive safety equipment and are therefore suitable for unsupervised continuous operation. Relevant operating conditions are constantly monitored and the system is switched off if necessary or with the process safety feature the emergency cooling circuit is activated.     The new multi-touch controller Pilot ONE offers a brilliant 5.7" touchscreen with graphic functions and a comfortable navigation menu. All important operating parameters and temperature values are neatly displayed on the touchscreen. Thanks to the new favourites menu, the one-click operation and the integrated technical glossary the operation is very easy, just like on a smartphone. Integrated USB and Ethernet ports allows connection to a PC or network, e.g. for remote control or data transmission.   Data Sheet  3 Years Warranty Extension Operating manuals General information & temperature controller Temperature range -55...250 °C Temperature stability ±0.01 °C Temperature control TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C Alarm message optical, acoustical Controller Pilot ONE (E-grade "professional") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 540 x 604 x 1332 mm | 21.26 x 23.78 x 52.44 inches Weight 212 kg | 467.46 pounds Heating / cooling capacity Heating capacity 9 kW Cooling capacity 250       200    100    20   0   -20   -40   -50   °C           6          6       6        6     6         1,2       0,65    kW          250 200 Cooling machine water-cooled Refrigerant (ASHRAE, GHS) R452A (A1, H280) (1,44 kg) Circulation pump Pressure pump max. 79 lpm ; 1.5 bar | 20.87 gpm ; 21.75 psi Pump connection M30x1,5 AG male Permissible viscosity 50 mm²/s Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating data Permissible ambient temp. 5...40 °C Noise level 61 dB(A) Filling volume min. 4.9 Liters | 1.29 gal Volume of expansion 16 Liters | 4.23 gal Cooling water connection G1/2 AG Cooling water differential pressure min. 1 bar | 14.5 psi Cooling water pressure max. 6 bar | 87 psi Power supply 460V 3~ 60Hz Current max. 13 A

Read more less

HUBER Unistat 815 Dynamic Temperature Control  (Please Note: There is a 2 - 3 weeks lead time)               Unistat Circulators are an ideal solution for fast and precise thermal control of externally connected applications. These systems offer rapid temperature change and a wide temperature range without having to change fluid. The new Pilot ONE controller features a navigation system with easily remembered icons and menus which are sorted by color to make routine work simpler. An amazing software guides you through your set up ensuring all the necessary settings are correct.   Unistat 815 208V Data sheet  Unistat 815 460V Data sheet  3 Year Warranty Extension    General Information & Temperature Controller Unistat 815208V Unistat 815460V Temperature range -85...250 °C -85...250 Temperature stability ±0.01 °C ±0.01 Temperature control TAC, self-optimizing (True Adaptive Control) TAC, self-optimizing (True Adaptive Control) Alarm message optical, acoustical optical, acoustical Controller Pilot ONE (E-grade "Professional") Pilot ONE (E-grade "Professional") Safety class III / FL III / FL Protection class IP20 IP20 Dimensions (W x D x H) 18.11 x 23.78 x 65.55 inches 18.11 x 23.78 x 57.68 inches Weight 331 kg | 729.86 pounds 229 kg | 504.94 pounds Heating / Cooling Capacity Heating capacity 2 kW 2,6 kW Cooling machine air-cooled air-cooled Refrigerant 1. stage R452A (A1, H280) (1,8 kg) R452A (A1, H280) (1,8 kg) Refrigerant 2. stage R23 (A1, H280) (0,39 kg) R23 (A1, H280) (0,39 kg) Circulation Pump Pressure pump max. 40 lpm ; 0.9 bar | 10.57 gpm ; 13.05 psi 40 lpm ; 0.9 bar | 10.57 gpm ; 13.05 psi Pump connection M30x1,5 AG male M30x1,5 AG male Permissible viscosity 50 mm²/s 50 mm²/s Connections Pt100 connection Pt100 Pt100 Digital interface RS232, Ethernet, USB Device, USB Host RS232, Ethernet, USB Device, USB Host Analogue input via optional Com.G@te via optional Com.G@te Analogue output via optional Com.G@te via optional Com.G@te Operating Data Old Sku 1014.0054.01 1014.0055.01 Permissible ambient temp. 5 to 40 °C 5 to 40 °C Noise Level 64 dB(A) 64 dB(A) Filling volume min. 3.8 Liters / 1 gal 3.8 Liters / 1 gal Volume of expansion 3.3 Liters / 0.87 gal 3.3 Liters / 0.87 gal Power supply 208V 3~ 60Hz 460V 3~ 60Hz Current max 21,5 A 11 A

Read more less

HUBER Unistat 825 Dynamic Temperature Control  (Please Note: There is a 2  weeks Shipping  lead time)        Unistat Circulators are an ideal solution for fast and precise thermal control of externally connected applications. These systems offer rapid temperature change and a wide temperature range without having to change fluid. The new Pilot ONE controller features a navigation system with easily remembered icons and menus which are sorted by color to make routine work simpler. An amazing software guides you through your set up ensuring all the necessary settings are correct.   General Information & Temperature Controller Unistat 825208V Unistat 825460V Temperature range -85...250 °C -85...250 Temperature stability ±0.01 °C ±0.01 Temperature control TAC, self-optimizing (True Adaptive Control) TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C 0.01 °C Alarm message optical, acoustical optical, acoustical Controller Pilot ONE (E-grade "Professional") Pilot ONE (E-grade "Professional") Safety class III / FL III / FL Protection class IP20 IP20 Dimensions (W x D x H) 18.11 x 23.78 x 65.55 inches 18.11 x 23.78 x 57.68 inches Weight 696.78 Lb 487.3 Lb Heating / Cooling Capacity Heating capacity 3 kW 4 kW Cooling machine air-cooled air-cooled Refrigerant 1. stage R507 (1,8 kg) R507 (1,8 kg) Refrigerant 2. stage R23 R23 Circulation Pump Pressure pump max. 10.57 gpm ; 13.05 psi 10.57 gpm ; 13.05 psi Pump connection M30x1,5 AG male M30x1,5 AG male Permissible viscosity 50 mm²/s 50 mm²/s Connections Pt100 connection Pt100 Pt100 Digital interface RS232, Ethernet, USB Device, USB Host RS232, Ethernet, USB Device, USB Host Operating Data Permissible ambient temp. 5 to 40 °C 5 to 40 °C Noise level 64 dB(A) 64 dB(A) Filling volume min. 2.9 Liters / 0.77 gal 2.9 Liters / 0.77 gal Volume of expansion 3.6 Liters / 0.95 gal 3.6 Liters / 0.95 gal Power supply 208V 3~ 60Hz 460V 3~ 60Hz Current max 20 A 14,5 A

Read more less

HUBER Unistat 905 Dynamic Temperature Control  (Please Note: There is 8 week shipping lead time) Disclaimer: This item is Non-Refundable once ordered. Unistat Circulators are an ideal solution for fast and precise thermal control of externally connected applications. These systems offer rapid temperature change and a wide temperature range without having to change fluid. The new Pilot ONE controller features a navigation system with easily remembered icons and menus which are sorted by color to make routine work simpler. An amazing software guides you through your set up ensuring all the necessary settings are correct.   Unistat 905 208V Data sheet  Unistat 905 460V Data sheet      General Information & Temperature Controller Unistat 905 208V Unistat 905 460V Temperature range -90 to 250 °C -90 to 250 °C Temperature stability ±0.01 °C ±0.01 Temperature control TAC, self-optimizing (True Adaptive Control) TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C 0.01 °C Alarm message optical, acoustical optical, acoustical Controller Pilot ONE (E-grade "Professional") Pilot ONE (E-grade "Professional") Safety class III / FL III / FL Protection class IP20 IP20 Dimensions (W x D x H) 540 x 654 x 1738 mm | 21.26 x 25.75 x 68.43 inches 540 x 654 x 1500 mm | 21.26 x 25.75 x 59.06 inches Weight 396 kg | 873.18 pounds 275 kg | 606.38 pounds Heating / Cooling Capacity Heating capacity 6 kW 6 kW Cooling machine air-cooled air-cooled Refrigerant 1. stage R452A (A1, H280) (2,5 kg) R452A (A1, H280) (2,5 kg) Refrigerant 2. stage R23 (A1, H280) (0,75 kg) R23 Circulation Pump Pressure pump max. 48 lpm ; 0.9 bar | 12.68 gpm ; 13.05 psi 10.57 gpm ; 13.05 psi Pump connection M30x1,5 AG male M30x1,5 AG male Permissible viscosity 50 mm²/s 50 mm²/s Connections Pt100 connection Pt100 Pt100 Analogue input via optional Com.G@te via optional Com.G@te Analogue output via optional Com.G@te via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host RS232, Ethernet, USB Device, USB Host Operating Data Old sku 1035.0013.01 1035.0014.01 Permissible ambient temp. 5...35 °C 5...35 °C Filling volume min. 3.2 Liters | 0.85 gal 3.2 Liters | 0.85 gal Volume of expansion 5.3 Liters | 1.4 gal 5.3 Liters | 1.4 gal Power supply 208V 3~ 60Hz 460V 3~ 60Hz Current max 40 A 23,5 A

Read more less

Huber Unistat 915w with Pilot ONE (Please Note: There is a 2 - 3 weeks lead time)               Unistat Circulators are an ideal solution for fast and precise thermal control of externally connected applications. These systems offer rapid temperature change and a wide temperature range without having to change fluid. The new Pilot ONE controller features a navigation system with easily remembered icons and menus which are sorted by color to make routine work simpler. An amazing software guides you through your set up ensuring all the necessary settings are correct.   Precise and reproducible temperature control results Fastest heating and cooling rate Wide temperature ranges with no fluid change Pilot ONE controller with 5.7“ touchscreen and comfortable menu navigation Adaptive temperature control, self-optimising  Efficient circulation pump Data communication via LAN, internet, USB, RS232 and RS485 Efficient operation saves working time and operating costs Proven functionality for the process industry  E-grade "Professional" included     Download Data Sheet  Click Here for 3 Year Warranty Online Registration  Download Operating Manual      General information & Temperature Controller Temperature range -90...250 °C Temperature stability ±0.02 °C ±0.01 °C Temperature control TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C Alarm message optical, acoustical Controller Pilot ONE (E-grade "Professional") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 630 x 704 x 1565 mm | 24.8 x 27.72 x 61.61 inches Weight 364 kg | 802.62 pounds Heating / Cooling Capacity Heating capacity 6 kW Cooling capacity 250 200 100 0 -20 -40 -60 -80 -90 °C 6,5 7,5 9 11 11 11 8,2 4,2 1,3 0,6 kW Cooling machine water-cooled Refrigerant 1. stage R507 (A1, H280) (2,9 kg) Refrigerant 2. stage R23 (A1, H280) (1,23 kg) Circulation Pump Pressure pump max. 110 lpm ; 1.5 bar | 29.06 gpm ; 21.75 psi Pump Connection M30x1,5 AG male Permissible viscosity 50 mm²/s Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating Data Old sku 1055.0011.01 Permissible ambient temp. 5...40 °C Noise level 64 dB(A) Filling volume min. 3.9 Liters | 1.03 gal Volume of expansion 6.5 Liters | 1.72 gal Cooling water connection G3/4 AG Cooling water differential pressure min. 1 bar | 14.5 psi Cooling water pressure max. 6 bar | 87 psi Power supply 460V 3~ 60Hz Current max. 29 A

Read more less

Huber Unistat 510 with Pilot ONE   The Unistat range inspires with unique thermodynamic properties and a range of functions to meet the highest demands. Unistat technology guarantees precise, reproducible temperature control results, the shortest possible heating and cooling times and large temperature ranges without the need for fluid change. All Unistats are fitted with the innovative Pilot ONE controller with a 5.7“ touchscreen color display and easy menu navigation. All important parameters can be seen at a glance and temperature curves are displayed in graphic real time. Unistats are equipped with the most up-to-date pump technology for optimal heat transfer. The pump self regulates to ensure the best possible circulation and flow and delicate glass reactors are protected from breakage by the pumps soft start-up feature. Unistat technology impresses as a result of economic operation with reduced operating costs and efficient energy management. Because Unistats are hydraulically sealed, the service life of the temperature control fluid is dramatically increased by preventing oil loss through vapours and oxidation, further saving resources. Unistats are fitted with extensive safety equipment and are therefore suitable for unsupervised continuous operation. Relevant operating conditions are constantly monitored and the system is switched off if necessary or with the process safety feature the emergency cooling circuit is activated.   The new multi-touch controller Pilot ONE offers a brilliant 5.7" touchscreen with graphic functions and a comfortable navigation menu. All important operating parameters and temperature values are neatly displayed on the touchscreen. Thanks to the new favorite menu, the one-click operation and the integrated technical glossary the operation is very easy, just like on a smartphone. Integrated USB and Ethernet ports allows connection to a PC or network, e.g. for remote control or data transmission.   FEATURES: Precise and reproducible temperature control results        Fastest heating and cooling rates                Wide temperature ranges with no fluid change     Pilot ONE controller with 5.7“ touchscreen and comfortable menu navigation         Adaptive temperature control, self-optimising       Efficient circulation pump                2 x USB (Host and Device), Ethernet and RS232 interfaces                 Efficient operation saves working time and operating costs              Proven functionality for the process industry          E-grade "Professional" include    Data Sheet  3 Year Warranty Extension  Note of Installation    General information & temperature controller Temperature range -50...250 °C Temperature stability ±0.01 °C Temperature stability TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C Alarm message optical, acoustical Controller Pilot ONE (E-grade "Professional") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 560 x 754 x 1457 mm | 22.05 x 29.68 x 57.36 inches Weight 348 kg | 767.34 pounds Heating / cooling capacity Heating capacity 6 kW Cooling capacity 250 200 100 0 -20 -40 -50 C5,3 5,3 5,3 5,3 2,8 0,9 0,25 kW Cooling machine air-cooled Refrigerant (ASHRAE, GHS) R452A (A1, H280) (2,8 kg) Circulation pump Pressure pump max. 112 lpm ; 1.5 bar | 29.59 gpm ; 21.75 psi Pump connection M30x1,5 AG male Permissible viscosity 50 mm²/s Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating data Permissible ambient temp. 5...40 °C Filling volume min. 4.1 Liters | 1.08 gal Volume of expansion 5.5 Liters | 1.45 gal Power supply 208V 3~ 60Hz Current max. 36 A

Read more less

Huber Unistat 510 with Pilot ONE   The Unistat range inspires with unique thermodynamic properties and a range of functions to meet the highest demands. Unistat technology guarantees precise, reproducible temperature control results, the shortest possible heating and cooling times and large temperature ranges without the need for fluid change. All Unistats are fitted with the innovative Pilot ONE controller with a 5.7“ touchscreen color display and easy menu navigation. All important parameters can be seen at a glance and temperature curves are displayed in graphic real time. Unistats are equipped with the most up-to-date pump technology for optimal heat transfer. The pump self regulates to ensure the best possible circulation and flow and delicate glass reactors are protected from breakage by the pumps soft start-up feature. Unistat technology impresses as a result of economic operation with reduced operating costs and efficient energy management. Because Unistats are hydraulically sealed, the service life of the temperature control fluid is dramatically increased by preventing oil loss through vapours and oxidation, further saving resources. Unistats are fitted with extensive safety equipment and are therefore suitable for unsupervised continuous operation. Relevant operating conditions are constantly monitored and the system is switched off if necessary or with the process safety feature the emergency cooling circuit is activated.   The new multi-touch controller Pilot ONE offers a brilliant 5.7" touchscreen with graphic functions and a comfortable navigation menu. All important operating parameters and temperature values are neatly displayed on the touchscreen. Thanks to the new favorite menu, the one-click operation and the integrated technical glossary the operation is very easy, just like on a smartphone. Integrated USB and Ethernet ports allows connection to a PC or network, e.g. for remote control or data transmission.   FEATURES: Precise and reproducible temperature control results        Fastest heating and cooling rates                Wide temperature ranges with no fluid change     Pilot ONE controller with 5.7“ touchscreen and comfortable menu navigation         Adaptive temperature control, self-optimizing       Efficient circulation pump                2 x USB (Host and Device), Ethernet and RS232 interfaces                 Efficient operation saves working time and operating costs              Proven functionality for the process industry          E-grade "Professional" include   Data Sheet 3 Year Warranty Extension Notes on Installation      General information & temperature controller Temperature range -50...250 °C Temperature stability ±0.01 °C Temperature stability TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C Alarm message optical, acoustical Controller Pilot ONE (E-grade "Professional") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 560 x 754 x 1457 mm | 22.05 x 29.68 x 57.36 inches Weight 233 kg | 513.76 pounds Heating / cooling capacity Heating capacity 6 kW Cooling capacity 250 200 100 0 -20 -40 -50 C5,3 5,3 5,3 5,3 2,8 0,9 0,25 kW Cooling machine air-cooled Refrigerant (ASHRAE, GHS) R452A (A1, H280) (2,8 kg) Circulation pump Pressure pump max. 112 lpm ; 1.5 bar | 29.59 gpm ; 21.75 psi Pump connection M30x1,5 AG male Permissible viscosity 50 mm²/s Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating data Permissible ambient temp. 5...40 °C Filling volume min. 4.1 Liters | 1.08 gal Volume of expansion 5.5 Liters | 1.45 gal Power supply 460V 3~ 60Hz Current max. 16 A

Read more less

PRESTO W55 JULABO PRESTO® Highly Dynamic Temperature Control Systems for highly precise temperature control of external applications. Systems offer rapid heating and cooling rates for fast compensation of external events. The hydraulically sealed heat exchanger design afford a wide working temperature range without changing fluids. All units feature a 5.7″ industrial color TFT touch screen interface for unit operation, external integration and programming. These instruments cover a working temperature range of -30 to +250°C to -92 to 250 °C. Up to three user levels with password management enable safe, repeatable operation. Systems incorporate USB (host and device), Ethernet, SD-card slot, RS232 port, stand-by input and Pt100 external temperature sensor port. The graphite bearing centrifugal pressure pump is lubricated by the bath fluid. All models (except for A30) can operate under pressure control to safeguard pressure sensitive applications (such as jacketed glass reactors). Air and water-cooled versions available. Use only with approved JULABO fluids. Systems can operate with silicone fluids (Thermal P60 and Thermal P90) and HFEs (Fluorinert® and Galden®). Single stage PRESTO systems can operate with 1:1 ethylene glycol/water mixtures from -30 to +90 °C. Additional accessories available.   Product Data Sheet    Key Benefits   For highly precise, external temperature applications Rapid heating and cooling Fast compensation of exothermic reaction Wide working temperature ranges without changing fluids Highest performance with small footprint Space-saving design optimizes space utilization in your lab NEW 5,7” industrial color TFT touch screen well-organized view of important information with unmatched, intuitive user friendliness Up to 3 user level with password management NEW USB (Host und Device) NEW Ethernet NEW SD-Card slot RS232 / optional RS485 / optional Profibus DP Stand-by input Filling system accessible from the top     Specifications Cooling Capacity °C 200 20 0 -10 -20 -30 -40 -50 kW 13.5 15 10 6.5 4 2.5 1.2 0.3 Heating or Cooling Capability Both Working Temp Range (°C) -55 … +250 Pump Capacity Flow Rate (l/min) 35…80 External Devices External Temp Probe, Remote Control Dimensions W x L x H (in) 24 x 33.3 x 49.2 Fluid Type Silicone, Fluorinert/Galden, Other Weight (lbs) 634.9 Power Options 208 V – 230 V / 3 Ph. / 60 Hz, 400 V / 3 Ph. / 50 Hz Heating Capacity (kW) 12.5 @ 208 V, 15 @ 230 V, 15 @ 400 V

Read more less

PRESTO W56 PRESTO W56 water-cooled highly dynamic temperature control unit. Range -56…+250 °C with 27 kW heating power and 25.8 kW cooling power at 20 °C. Powerful circulating pumps, electronically adjustable in stages or by setting the pressure valueChoose between a magnetically coupled centrifugal pump or a magnetically coupled gear pump for pressures up to 3.2 bar and virtually constant flow rate at any pressure Integrated 5.7” industrial color touchscreen displays all essential information and enables simple fingertip control Extensive warning, protection, and monitoring functions with detailed self-explanatory messages  ICC cascade control for extraordinary precision, temperature stability ±0.05 °C ... ±0.2 °C Ambient temperature range +5 °C to +40 °C Integrated programmer with real-time clock Filling level indicator and pump capacity displayed electronically  Interface for SD memory card  Connections for USB, Ethernet, RS232, and Alarm output Integrated Modbus  Optional analog connections, RS485, Profibus DP  1-stage water-cooled refrigeration system Sealed design enables operation to 150 °C with glycol/water and accessories     Specifications Colling Capacity °C 200 20 0 -10 -20 -30 -40 -50 kW 19 25.8 23.1 16.9 11.5 7.1 3.5 1.4 Heating or Cooling Capability Both Dimensions W x L x H (in) 23.6 x 37 x 64.6 External Devices External Temp Probe, Remote Control Fluid Type Silicone, Water/Glycol, Fluorinert/Galden Heating Capacity (kW) 27 Power Options 480 V / 3 PPE / 60 Hz, 400 V / PPE / 50 Hz Pump Capacity Flow Pressure (psi) 7…46.4 Pump Capacity Flow Rate (l/min) 35…80 Weight (lbs) 849 Working Temp Range (°C) -56 … +250     Data Sheet    Brochure      Please note:  NRTL will require the units to be inspected before shipping and will add a few weeks to any units in stock, if not in stock lead time is 22-26 weeks

Read more less

PRESTO W80     JULABO PRESTO® Highly Dynamic Temperature Control Systems for highly precise temperature control of external applications. Systems offer rapid heating and cooling rates for fast compensation of external events. The hydraulically sealed heat exchanger design afford a wide working temperature range without changing fluids. All units feature a 5.7″ industrial color TFT touch screen interface for unit operation, external integration and programming. These instruments cover a working temperature range of -30 to +250°C to -92 to 250 °C. Up to three user levels with password management enable safe, repeatable operation. Systems incorporate USB (host and device), Ethernet, SD-card slot, RS232 port, stand-by input and Pt100 external temperature sensor port. The graphite bearing centrifugal pressure pump is lubricated by the bath fluid. All models (except for A30) can operate under pressure control to safeguard pressure sensitive applications (such as jacketed glass reactors). Air and water-cooled versions available. Use only with approved JULABO fluids. Systems can operate with silicone fluids (Thermal P60 and Thermal P90) and HFEs (Fluorinert® and Galden®). Single stage PRESTO systems can operate with 1:1 ethylene glycol/water mixtures from -30 to +90 °C. Additional accessories available.   Product Data Sheet    Key Benefits   For highly precise, external temperature applications Rapid heating and cooling Fast compensation of exothermic reaction Wide working temperature ranges without changing fluids Highest performance with small footprint Space-saving design optimizes space utilization in your lab NEW 5,7” industrial color TFT touch screen well-organized view of important information with unmatched, intuitive user friendliness Up to 3 user level with password management NEW USB (Host und Device) NEW Ethernet NEW SD-Card slot RS232 / optional RS485 / optional Profibus DP Stand-by input Filling system accessible from the top Water cooled     Specifications Cooling Capacity °C 200 100 20 0 -20 -40 -60 -80 kW 1.2 1.2 1.2 1.2 1.1 1.1 0.65 0.1 Heating or Cooling Capability Both Working Temp Range (°C) -80 … +250 Pump Capacity Flow Rate (l/min) 16…40 Pump Capacity Flow Pressure (psi) 1.45…18.85 External Devices External Temp Probe, Remote Control Dimensions W x L x H (in) 16.9 x 25.6 x 49.5 Fluid Type Silicone, Fluorinert/Galden Weight (lbs) 351 Power Options 208 V / 60 Hz, 230 V / 50 Hz Heating Capacity (kW) 1.5 @ 208 V / 60 Hz, 1.8 @ 230 V / 50 Hz

Read more less

Julabo PRESTO A40 Reactor temperature control, tests for all kinds of substances or temperature simulation – Presto A30 are made for highly precise temperature control and rapid temperature changes, providing large heating and cooling capacities covering a working temperature range from -92 °C to +250 °C. Highly efficient components allow extremely fast  compensation of exothermic and endothermic reactions. Lab users benefit from high flow rates, constant pressure and a controlled build-up of pump pressure. Changes in the temperature-control fluid viscosity are balanced dynamically. Permanent internal monitoring and self-lubricating pumps contribute to the new PRESTO’s long service life. A special feature of the PRESTO is the integrated 5.7’’ industrial color touch screen.      Specifications Shipping Weight 231 lbs Shipping Dimensions 40 x 24 x 40 in Order No. 9420401 Model Series PRESTO Working Temperature Range (°C) -40° to +250° Temperature Stability (°C) ±0.01 … ±0.05 Temperature Control ICC intelligent cascade control, TCF temperature controlfeatures, Absolute temperature calibration 1-point Display Resolution 0.01 °C Integrated Programmer 8 x 60 steps Temperature Display TFT Touchscreen Heating Capacity (kW) 2.3 Cooling Capacity °C 200 100 20 0 -20 -30 -40kW 1.2 1.2 1.2 0.9 0.6 0.3 0.1 Pump capacity Flow Rate (l/min) 16 to 40 Pump Capacity Flow Pressure (psi) 1.45 to 18.85 Pump Connections M24x1.5 Filling Volume Liters 3.5 (1.7 Internal Expansion) Refrigerant R507 External Pt100 integrated Digital Interface RS232, Optional Profibus, SD memory card, USB, Ethernet, Modbus, Optional RS485 Ambient Temperature 5…40 °C Noise Level (dBA) 55 Classification Classification III (FL)according to DIN 12876-1 Analog Connection Input / Output Optional Cooling of Compressor 1-stage Air Filling Volume Expansion Vessel Liters 2.7 Power requirement V / Hz / A 208/60/15 Alarm Signal acoustically & optical Temperature Selection / Display °C / °F Outer dimensions W x L x H inch 12.7 x 22.9 x 26 Other Characteristics GB version with 1800 W heater Characteristics / Display State-of-the-art display technology: TFT Display for comfortable user guidance, colored display of

Read more less

Julabo PRESTO A45 Reactor temperature control, tests for all kinds of substances or temperature simulation – Presto A30 are made for highly precise temperature control and rapid temperature changes, providing large heating and cooling capacities covering a working temperature range from -92 °C to +250 °C. Highly efficient components allow extremely fast  compensation of exothermic and endothermic reactions. Lab users benefit from high flow rates, constant pressure and a controlled build-up of pump pressure. Changes in the temperature-control fluid viscosity are balanced dynamically. Permanent internal monitoring and self-lubricating pumps contribute to the new PRESTO’s long service life. A special feature of the PRESTO is the integrated 5.7’’ industrial color touch screen.     Key Benefits: For highly precise, external temperature applications Rapid heating and cooling Fast compensation of exothermic reaction Wide working temperature ranges without changing fluids Highest performance with small footprint Space-saving design optimizes space utilization in your lab NEW 5,7” industrial color TFT touch screen well-organized view of important information with unmatched, intuitive user friendliness Up to 3 user level with password management NEW USB (Host und Device) NEW Ethernet NEW SD-Card slot RS232 / optional RS485 / optional Profibus DP Stand-by input Filling system accessible from the top Removable venting grid for simplified removal of dust   Specifications Shipping Weight 251 lbs Shipping Dimensions 40 x 24 x 40 in Order No. 9420452 Model Series PRESTO Working Temperature Range (°C) -45°...+250° Temperature Stability (°C) ±0.05 … ±0.1 Temperature Control ICC intelligent cascade control, TCF temperature controlfeatures, Absolute temperature calibration 1-point Display Resolution 0.01 °C Integrated Programmer 8 x 60 steps Temperature Display TFT Touchscreen Heating Capacity (kW) 2.3 Cooling Capacity Pump capacity Flow Rate (l/min) 35...76 Pump Capacity Flow Pressure (psi) 6.74 … 43.5 @ 208V, 6.74 Pump Connections M30x1.5 Filling Volume Liters 7.5 (7.5 internal expansion) Refrigerant R507 External Pt100 integrated Digital Interface RS232, Optional Profibus, SD memory card, USB, Ethernet, Modbus, Optional RS485 Ambient Temperature 5…40 °C Noise Level (dBA) 69 Classification Classification III (FL)according to DIN 12876-1 Analog Connection Input / Output Optional Cooling of Compressor 1-stage Air Filling Volume Expansion Vessel Liters 7.5 Power requirement V / Hz / A 3x 208/60/23 Alarm Signal acoustically & optical Temperature Selection / Display °C / °F Outer dimensions W x L x H inch 20.9 x 26.2 x 49.6   Product Data Sheet

Read more less

Julabo PRESTO A45T Reactor temperature control, tests for all kinds of substances or temperature simulation – Presto A30 are made for highly precise temperature control and rapid temperature changes, providing large heating and cooling capacities covering a working temperature range from -92 °C to +250 °C. Highly efficient components allow extremely fast  compensation of exothermic and endothermic reactions. Lab users benefit from high flow rates, constant pressure and a controlled build-up of pump pressure. Changes in the temperature-control fluid viscosity are balanced dynamically. Permanent internal monitoring and self-lubricating pumps contribute to the new PRESTO’s long service life. A special feature of the PRESTO is the integrated 5.7’’ industrial color touch screen.      Specs-At-A-Glance Cooling Capacity °C 200 20 0 -10 -20 -30 -40 kW 3.4 3.5 3.3 2.6 1.8 1 0.3 Heating Capacity (kW) 5.5 @ 208V, 6 @ 230V, 6 @ 400V Heating or Cooling Capability Both Working Temp Range (°C) -45 … +250 Pump Capacity Flow Rate (l/min) 35 … 76 Pump Capacity Flow Pressure (psi) 6.74 … 43.5 @ 208V, 6.74 … 46.4 @ 230V, 6.74 … 46.4 @ 400V External Devices External Temp Probe, Remote Control Dimensions W x L x H (in) 20.9 x 26.2 x 49.6 Fluid Type Silicone, Fluorinert/Galden, Other Weight (lbs) 463

Read more less

Julabo PRESTO A80 Reactor temperature control, tests for all kinds of substances or temperature simulation – Presto A30 are made for highly precise temperature control and rapid temperature changes, providing large heating and cooling capacities covering a working temperature range from -92 °C to +250 °C. Highly efficient components allow extremely fast  compensation of exothermic and endothermic reactions. Lab users benefit from high flow rates, constant pressure and a controlled build-up of pump pressure. Changes in the temperature-control fluid viscosity are balanced dynamically. Permanent internal monitoring and self-lubricating pumps contribute to the new PRESTO’s long service life. A special feature of the PRESTO is the integrated 5.7’’ industrial color touch screen.    Key Benefits: For highly precise, external temperature applications Rapid heating and cooling Fast compensation of exothermic reaction Wide working temperature ranges without changing fluids Highest performance with small footprint Space-saving design optimizes space utilization in your lab NEW 5,7” industrial color TFT touch screen well-organized view of important information with unmatched, intuitive user friendliness Up to 3 user level with password management NEW USB (Host und Device) NEW Ethernet NEW SD-Card slot RS232 / optional RS485 / optional Profibus DP Stand-by input Filling system accessible from the top Removable venting grid for simplified removal of dust   Specs-At-A-Glance Cooling Capacity °C 200 100 0 -20 -40 -60 -80 kW 1.2 1.1 1.2 1.1 1.1 0.65 0.1 Heating Capacity (kW) 10 @ 208V, 12 @ 230V, 12 @ 400V Heating or Cooling Capability Both Working Temp Range (°C) -45 … +250 Pump Capacity Flow Rate (l/min) 35 … 76 Pump Capacity Flow Pressure (psi) 6.74 … 43.5 @ 208V, 6.74 … 46.4 @ 230V, 6.74 … 46.4 @ 400V Filling Volume Liters 3.9 (1.7 internal expansion) Digital Interface RS232, Optional Profibus, SD memory card, USB, Ethernet, Modbus, Optional RS485 Noise Level (dBA) 68 Power requirement V / Hz / A 208/60/15 Cooling of Compressor 2-stage Air External Devices External Temp Probe, Remote Control Dimensions W x L x H (in) 20.9 x 26.2 x 49.6 Fluid Type Silicone, Fluorinert/Galden, Other Weight (lbs) 463   Product Data Sheet 

Read more less

Julabo PRESTO A85 Reactor temperature control, tests for all kinds of substances or temperature simulation – Presto A30 are made for highly precise temperature control and rapid temperature changes, providing large heating and cooling capacities covering a working temperature range from -92 °C to +250 °C. Highly efficient components allow extremely fast  compensation of exothermic and endothermic reactions. Lab users benefit from high flow rates, constant pressure and a controlled build-up of pump pressure. Changes in the temperature-control fluid viscosity are balanced dynamically. Permanent internal monitoring and self-lubricating pumps contribute to the new PRESTO’s long service life. A special feature of the PRESTO is the integrated 5.7’’ industrial color touch screen.    Key Benefits: For highly precise, external temperature applications Rapid heating and cooling Fast compensation of exothermic reaction Wide working temperature ranges without changing fluids Highest performance with small footprint Space-saving design optimizes space utilization in your lab NEW 5,7” industrial color TFT touch screen well-organized view of important information with unmatched, intuitive user friendliness Up to 3 user level with password management NEW USB (Host und Device) NEW Ethernet NEW SD-Card slot RS232 / optional RS485 / optional Profibus DP Stand-by input Filling system accessible from the top Removable venting grid for simplified removal of dust     Specs-At-A-Glance Temperature Stability (°C) ±0.05 … ±0.1 Cooling Capacity °C 200 20 0 -20 -40 -60 -80 kW 2.8 2.5 2.4 2.4 2.4 2.2 0.4 Heating Capacity (kW) 6 @ 400V, 6 @ 230V, 5.5 @ 208V Heating or Cooling Capability Both Working Temp Range (°C) -85 … +250 Pump Capacity Flow Rate (l/min) 35 … 76 Pump Capacity Flow Pressure (psi) 6.96 … 46.42 @ 400V, 6.96 … 46.42 @ 230V, 6.96 … 43.51 @ 208V Filling Volume Liters 9.5 (7 internal expansion) Digital Interface RS232, Optional Profibus, SD memory card, USB, Ethernet, Modbus, Optional RS485 Noise Level (dBA) 69 Power requirement V / Hz / A 3x 208/60/30 Cooling of Compressor 2-stage Air External Devices External Temp Probe, Remote Control Dimensions W x L x H (in) 24.1 x 42.6 x 49.3 Fluid Type Silicone, Fluorinert/Galden, Other Weight (lbs) 805   Product Data Sheet 

Read more less

Julabo Adapter 8891609 M16x1 f to NPT 1/2″ f 2 Adapters M16x1 f. to NPT 1/2″ f.

Read more less

Julabo Adapter M16x1 f to NPT 1/2″     2 Adapters M16x1 f. to NPT 1/2″ m.

Read more less

Julabo Triple Insulated Metal Tubing -100°C to 350°C This flexible metal tubing can be bolted together with the circulator and the external system thus avoiding slipping. The integrated insulation avoids loss of performance. Triple insulated for wide temperature ranges. Connection size is a M16x1 female fitting on each end and comes in varying lengths from 0.5 to 3m long.

Read more less

Adapters M24x1.5 female to NPT 1/2" male   2 Adapters M24x1.5 female to NPT 1/2″ male

Read more less

Adapter M30x1.5 male to male   Adapter M30x1.5 male to male

Read more less

Huber adapter M16x1f-1/2"m Adapter M16x1 f - R1/2 m Adapter M16x1 f - R1/2 m M16x1 female thread to R1/2 male thread

Read more less

PolyScience polyclean CLARIFIER      - 8 oz  Description Keeps reservoirs clean and odor-free. Concentrated: 8 oz (237 ml) treats approximately 200 gallons (757 liters). Quantity: 8oz (237 ml) Temperature Range: n/a Part Number: 004-300040 Safety Data Sheet (SDS) For use with:  Circulating Baths Refrigerated Circulating Baths Heating Circulating Baths Stainless Steel Open Bath Systems Polycarbonate Open Bath Systems Viscosity Bath Calibration Bath 75L Refrigerated Circulating Bath Coliform Bath General Purpose Water Baths LM Series Benchtop LS Series Benchtop MM Series Benchtop 6000 Series Chiller 3370 Liquid-to-Air Cooler 4100 Liquid-to-Liquid Cooler

Read more less

MVP - Fuego 240v Heater - Ethanol All sales final

Read more less

Huber Unistat Tango with Pilot ONE (Please Note: There is  2-3  weeks Shipping  lead time)          Unistats are predestined for applications in process and chemical engineering, such as temperature control of reactors, autoclaves, Miniplant/Pilot systems, reactor blocks and calorimeters. Unistat temperature control systems with their unique thermodynamics provide highly accurate and reproducible results, guaranteeing the shortest heating and cooling times and a wide temperature range without fluid change. Environmentally and economically Unistats stand out, offering natural refrigerants and an efficient energy management system for reduced operating costs. .  Precise and reproducible temperature control results Fastest heating and cooling rates Wide temperature ranges with no fluid change Pilot ONE controller with 5.7“ touchscreen and comfortable menu navigation Adaptive temperature control, self-optimising Efficient circulation pump 2 x USB (Host and Device), Ethernet and RS232 interfaces Efficient operation saves working time and operating costs Proven functionality for the process industry E-grade "Professional" included      Download Data sheet Unistat tango  Download Data Sheet Unistat tango w Download Data Sheet Unistat tango wl Operating Manual  Click here 3 year Warranty Register    General Information & Temperature Controller Unistat Tango Unistat Tango w Unistat Tango wl Temperature range -45...250 °C -45...250 °C -45...250 °C Temperature stability ±0.01 °C ±0.01 ±0.01 °C Temperature control TAC, self-optimizing (True Adaptive Control) TAC, self-optimizing (True Adaptive Control) TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C 0.01 °C 0.01 °C Alarm message optical, acoustical optical, acoustical optical, acoustical Controller Pilot ONE (E-grade "Professional") Pilot ONE (E-grade "Professional") Pilot ONE (E-grade "Professional") Safety class III / FL III / FL III / FL Protection class IP20 IP20 IP20 Dimensions (W x D x H) 16.77 x 12.87 x 24.84 inches 16.77 x 12.87 x 24.84 inches 16.77 x 12.87 x 24.84 inches Weight 141.12 pounds 119.07 pounds 132.3 pounds Heating / Cooling Capacity Heating capacity 3 kW 3 kW 3 kW Cooling capacity 250 200 100 0 -20 -40 °C0,7 0,7 0,7 0,7 0,4 0,06 kW 250 200 100 0 -20 -40 °C0,7 0,7 0,7 0,7 0,4 0,06 kW 250 200 100 0 -20 -40 °C0,7 0,7 0,7 0,7 0,4 0,06 kW Cooling machine air-cooled water-cooled air- and water-cooled Refrigerant R1270 (0,15 kg) R1270 (0,09 kg R1270 (0,15 kg) Circulation Pump Pressure pump max. 55 lpm ; 0.9 bar | 14.53 gpm ; 13.05 psi 55 lpm ; 0.9 bar | 14.53 gpm ; 130.5 psi 55 lpm ; 0.9 bar | 14.53 gpm ; 130.5 psi Pump connection M24x1,5 AG male M24x1,5 AG male M24x1,5 AG male Permissible viscosity 50 mm²/s 50 mm²/s Connections Pt100 connection Pt100 Pt100 Pt100 Analogue input via optional Com.G@te via optional Com.G@te via optional Com.G@te Analogue outpu via optional Com.G@te via optional Com.G@te via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host RS232, Ethernet, USB Device, USB Host RS232, Ethernet, USB Device, USB Host Operating Data Permissible ambient temp. 5 to 40 °C 5 to 40 °C 5 to 40 °C Noise level 62 dB(A) - 62 dB(A) Filling volume min. 1.5 Liters | 0.4 gal 1.5 Liters | 0.4 gal 1.5 Liters | 0.4 gal Volume of expansion 2.8 Liters | 0.74 gal 2.8 Liters | 0.74 gal 2.8 Liters | 0.74 gal Cooling water connection - G1/2 AG G1/2 AG Cooling water consumption - 24 l/h 30 l/h Cooling water differential pressure min. - 0,5 bar | 72.5 psi 0,5 bar | 72.5 psi Cooling water pressure max. - 6 bar | 87 psi 6 bar | 87 psi Power supply 208V 2~ 60Hz 208V 2~ 60Hz 208V 2~ 60Hz Current max 18 A 16,5 A 17,5 A Fusing 20 A 2x20 A 2x20 A

Read more less

Huber Unistat T402 with Pilot ONE    The Unistat range inspires with unique thermodynamic properties and a range of functions to meet the highest demands. Unistat technology guarantees precise, reproducible temperature control results, the shortest possible heating and cooling times and large temperature ranges without the need for fluid change. All Unistats are fitted with the innovative Pilot ONE controller with a 5.7“ touchscreen color display and easy menu navigation. All important parameters can be seen at a glance and temperature curves are displayed in graphic real time. Unistats are equipped with the most up-to-date pump technology for optimal heat transfer. The pump self regulates to ensure the best possible circulation and flow and delicate glass reactors are protected from breakage by the pumps soft start-up feature. Unistat technology impresses as a result of economic operation with reduced operating costs and efficient energy management. Because Unistats are hydraulically sealed, the service life of the temperature control fluid is dramatically increased by preventing oil loss through vapors and oxidation, further saving resources. Unistats are fitted with extensive safety equipment and are therefore suitable for unsupervised continuous operation. Relevant operating conditions are constantly monitored and the system is switched off if necessary or with the process safety feature the emergency cooling circuit is activated.     Precise and reproducible temperature control results   Wide temperature ranges with no fluid change   Pilot ONE controller with 5.7“ touchscreen and comfortable menu navigation Adaptive temperature control, self-optimizing  Efficient circulation pump 2 x USB (Host and Device), Ethernet and RS232 interfaces   Efficient operation saves working time and operating costs  Proven functionality for the process industry  E-grade "Professional" included   General Information & Temperature Controller Temperature range 65...300 °C Temperature stability ±0.05 °C Temperature control TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C Alarm message optical, acoustical Controller Pilot ONE (E-grade "Basic") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 505 x 400 x 765 mm | 19.88 x 15.75 x 30.12 inches Weight 54 kg | 119.07 pounds Heating / Cooling Capacity Heating capacity 4,8 kW Circulation Pump Pressure pump max. 45 lpm ; 0.9 bar | 11.89 gpm ; 13.05 psi Pump connection M24x1,5 AG male Permissible viscosity 50 mm²/s Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating Data Old sku 1038.0004.01 Permissible ambient temp. 5 to 40 °C Filling volume min. 1.45 Liters | 0.38 gal Volume of expansion 2.8 Liters | 0.74 gal Power supply 208V 3~ 60Hz Cooling water Connection G1/2 AG

Read more less

HUBER KISS K6 Refrigerated Heating Bath     ( Please Note: There is a shipping lead time 2-3 weeks )        The Kiss K6 Refrigerated Heating Baths is ideal for a variety of heating and cooling tasks in research and industry such as sample temperature control, materials testing, quality control, analyses, etc. This unit consist of a stainless steel bath, immersion thermostat, pressure and suction pump with wetted materials made from industrial plastic or stainless steel, and air cooled refrigeration unit. In addition, the cooling circulators include automatic refrigeration capacity adjustment which reduces energy consumption and waste heat down to the absolute essential. New KISS controller combines state-of-the-art technology with stylish design. The simple to navigate menu makes operating these baths as easy as pushing a few buttons.   Download Data Sheet  Click Here 3 Year Warranty Register  Please observe the notes on installation and/or the space requirements of our products.   General Information & Temperature Controller Temperature range -25 to 200 °C Temperature stability ±0.05 °C Temperature Display OLED Display Alarm message optical, acoustical Controller KISS Safety class III / FL Protection class IP20 Dimensions (W x D x H) 210 x 400 x 546 mm | 8.27 x 15.75 x 21.5 inches Weight 25 kg | 55.12 pounds Heating / Cooling Capacity Heating capacity 1,5 kW Cooling capacity 20 0 -10 -20 °C0,2 0,15 0,1 0,05 kW Cooling machine air-cooled Refrigerant R290 (A3, H220) (0,047 kg) Circulation Pump Pressure pump max. 14 lpm ; 0.25 bar | 3.7 gpm ; 3.62 psi Suction pump max. 10.5 lpm ; 0.17 bar | 2.77 gpm ; 2.47 psi Pump connection M16x1 AG male Connections Digital interface USB, RS232 Operating Data Old sku 2008.0023.99 Permissible ambient temp. 5 to 40 °C Bath opening W x D / BD 5.51 x 4.72 / 5.91 inches Bath volume 4.5 Liters | 1.19 gal Power supply 110-120V 1~ 50/60Hz Current max. 15 + 3,2 A

Read more less