Resins & Dyes

Premium Wood Stabilizer  Disclaimer: This product is intended for stabilization of wood products and is not intended for human consumption. Note: This product is compatible with Cactus Juice and can be blended. Precautionary Statement: Store at temperatures not exceeding 20°C /68°F Premium Wood Stabilizer SDS Premium Wood Stabilizer TDS Premium Wood Stabilizer Instructions   BVV Premium Wood Stabilizer is the first heat-curing methacrylate stabilizer developed specifically to satisfy the needs of discriminating woodworkers Previous thermocuring wood stabilizers are actually products developed many years ago for the automotive industry, with properties suited for engine block sealing, not wood stabilization. Characteristics like cloudiness, off-color tint, hardness, fluorescence, and retail availability are of little importance to an engine or transmission manufacturer. However, to a serious woodworker, these characteristics are of utmost importance in guaranteeing the quality of a finished product. Premium Wood Stabilizer cures crystal clear to a tough, hard finish, without the use of fluorescent markers and with low bleed-out. As a result, you’ll see the excellent turning, sanding, polishing, and aesthetic properties you expect. Premium Wood Stabilizer was developed by an international laboratory. Premium Wood Stabilizer works in most vacuum stabilization systems, is easy to use, requires little technical support, and is suitable for use with many water, alcohol, and oil-soluble dyes. Premium Wood Stabilizer is a pre-catalyzed blend of methacrylate esters that, when exposed to heat, will polymerize to a hard, clear finish that can be easily sanded and polished to a brilliant finish. Prior to first use or after an extended period of storage, entire contents should be de-gassed by subjecting contents to a vacuum of at least 25 inches of mercury for 30 minutes. Premium Wood Stabilizer will cure when exposed to 194°F (90°C) for at least 10 minutes. Therefore the time required to completely cure a stabilized blank will depend on factors such as wood thickness and density. The manufacturer makes no guarantee or warranty that Premium Wood Stabilizer is compatible with all dyes and stains and will not be liable for any loss due to incompatibility. It is recommended to test compatibility on a small sample first to reduce the risk of loss of wood or stabilizer. Key Benefits: Cures crystal clear to a tough, hard finish without the use of fluorescent markers and with low bleed-out Easy to use application Liquid Phase: Appearance Clear liquid Viscosity 20° C, Sec/t. Zahn: *(32-34s) Florescent dye added: No Drag Out g/m3: 33 Shelf life: 12 Months when stored properly Odor: Mild Specific Gravity @ 20°C: *(1.006-1.013) Surface tension: 32 dyne/cm Vapor pressure: <1 mm Hg Catalyzation Method: Mix upon use w/ supplied catalyst Gel Time: 2-5 minutes Relative absorption: 36% * Under recommended operating and storage conditions Cured Phase: Cure shrinkage: 13.2% Adhesive strength: 56 N/cm2 Pressure resistance: >12,000 psi Co-efficient/lln/exp: 0.000117 per °C Swelling H20/96hrs: 10.5 % Temperature range: -50/+200° C Storage: Store Premium Wood Stabilizer in a cool dry location below 68° F (20° C), refrigeration preferred. Store in original container or in HDPE. Do not store in copper or its alloys, mild steel, or tin.

Read more less

 Wood Stabilizing Resin with Activator  (Heated Cured)   Commercial Grade heat cured resin designed to penetrate and harden soft porous materials for smooth turning Disclaimer: Activator comes separated from resin wood stabilizer. It is intended for stabilization of wood products and is not intended for human consumption. Note: Spigots/Faucets are only compatible with 5 Gallon Jugs and must be purchased separately Note: This product is compatible with Cactus Juice and can be blended. Precautionary Statement: Store at temperatures not exceeding 20°C /68°F   Wood Stabilizing Resin SDS Wood Stabilizing Resin TDS Wood Stabilizing Resin Instructions     Aerospace approved heat-cured resin for stabilizing and hardening the wood and other porous material. This resin is reusable and does not significantly change the color of most woods. Prior to first use or after an extended period of storage, entire contents should be de-gassed by subjecting contents to a vacuum of at least 25 inches of mercury for 30 minutes. Wood Stabilizer will cure when exposed to 194°F (90°C) for at least 10 minutes. Therefore the time required to completely cure a stabilized blank will depend on factors such as wood thickness and density. Wood Stabilizer is compatible with many dyes and stains. However, BVV™ makes no guarantee or warranty that Wood Stabilizing Resin is compatible with all dyes and stains and will not be liable for any loss due to incompatibility. It is recommended to test compatibility on a small sample first to reduce risk of loss of wood or stabilizer

Read more less

Cactus Juice Wood Stabilizing Resin Cactus Juice Stabilizing Resin is the original premium professional grade heat cured resin for stabilizing and hardening wood and other porous material. This makes the wood harder, and much more resistant to moisture.  It is especially effective on those beautiful, punky, spalted woods that are just too soft to work with! Cactus Juice is easy to use and does not significantly change the color of most woods. It is NOT solvent-based and cures 99.99% from liquid to solid by weight, far superior to typical home stabilizing solutions such as Minwax Wood Hardener or polyurethane. Stop throwing away those punky blanks and give Cactus Juice a try!  Cactus Juice MSDS Key Benefits:  Stabilizes and hardens soft woods Minimal color change Lasts for months Reuse again and again Non-flammable Sizes Available: Pint Cactus Juice - Ready To Use 1 Quart Cactus Juice - Ready To Use 1/2 Gallon Cactus Juice - Activator Included 1 Gallon Cactus Juice - Activator Included   UNCURED PROPERTIES Composition/type: methacrylate ester monomersAppearance/Color: translucent, very light amber liquidViscosity @25ºC : 4-6 cpsSpecific Gravity: 1.03Flash Point: >200ºFVapor Pressure: Less than 5mm Hg at 72° FFlorescence: No CURED PROPERTIES Appearance: hard, translucent, plasticHardness Shore D (ASTM D2240): 80-85 CURING METHOD Cactus Juice is heat cured at temperatures between 80ºC -96ºC, (177º F -205º F ). Cactus Juice cures when the temperature of the resin within the blank reaches 90º C for 6-8 minutes.  The typical small shop method for curing is in a counter top toaster oven until internal blank temperature reaches the cure temperature  for 10 minutes or more. This usually take 1-1.5 hours for a typical small batch of 10 pen blanks.  Blanks with large cross section areas or larger batches of blanks may require longer processing times to achieve the required cure temperature. SERVICE TEMPERATURE RANGE Cactus Juice is formulated from the highest quality monomers to maximize the service operating range of the polymer. Cactus Juice is recommended for continuous service from –54ºC, (-65ºF) to 189ºC, (372ºF). STORAGE Activated Cactus Juice is easy to store and will exhibit an approximately 12 month shelf life under proper storage conditions. The resin should be stored in its original container and away from direct sunlight or other sources of UV light.  Storage temperatures should be maintained below 29ºC (85ºF).  Storage in a refrigerator is recommended. HANDLING ALL CHEMICALS SHOULD BE HANDLED WITH CARE!.Cactus Juice resin can be safely handled using normally accepted practices for handling non-toxic industrial chemicals. Rubber gloves should be worn when handling liquid Cactus Juice. Avoid excessive skin contact and wash thoroughly with water and mild soap if contact occurs. If dermatitis occurs, seek medical attention and avoid further exposure.  Avoid accidental contact with the eyes by using safety glasses. If accidental contact with the eyes should occur, flush immediately with copious amounts of clean water and obtain medical attention as necessary. WASTE TREATMENT Cured Cactus Juice is inert and can be disposed of as ordinary industrial trash. Uncured resin should be cured before disposal. Resin in solution in wash water effluent is biodegradable.    NOTES Information presented herein has been compiled from sources considered to be accurate and reliable, but is not guaranteed to be so. Nothing herein shall be considered as recommending practices or products in violation of any patent, law or regulation. It is the user's responsibility to determine the suitability of any material for a specific purpose and to adopt such safety precautions as may be necessary. TURNTEX, LLC MAKES NO WARRANTIES REGARDING THE PRODUCTS AND DISCLAIM ALL EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Read more less

Please note: Signature required by legal adult   Clear Casting and Coating System Alumilite's Amazing Clear Cast is a clear casting and coating system that cures to a rigid, durable, clear plastic. Use Amazing Clear Cast for coating or finishing applications such as bar tops, floors, taxidermy scenery, lenses, and all sorts of other clear casting or coating applications. Amazing Clear Cast is an easy to use, 1:1 mix ratio system that cures overnight which allows time for air bubbles to evacuate prior to curing. Amazing Clear Cast can be colored with Alumilite dyes, alcoholic inks, or other non-water base colorants. Complies with FDA CFR 177.2600 Continue to utilize a 1:1 Ratio of the Clear Cast even if the item may appear different as Side A & Side B are determined by weight.Temperature changes cause volumes to look different between Side A & Side B however this does not change the weight of the item.The Resin may cure faster when utilizing this product as heat will be produced.To slow down curing time refrigerate before use.   Shelf Life ACC has a shelf life of 1 year. Once ACC is opened, this time can be shorter based on moisture contamination from humidity. Amazing Clear Cast B side will naturally yellow over time and when exposure to air. While this can cause a yellow hue to cured coatings, it does not have an effect on the ultimate cure of the product. *Alumilite warns that this epoxy can begin to yellow as soon as 30-60 days after pouring. So, this epoxy is recommended for use over colorful backgrounds where slight yellowing won’t be noticed. Pouring over a stark white background may show the yellowing of the epoxy more.*   Specifications: Product Amazing Clear Cast Color Clear Mix Ratio 1:1 by **VOLUME** Pot Life 30-40 mins Demold Time(100 gr Mass) 24-48 hrs Mixed Viscosity (cps.) 2600 Specific Gravity 1.08 Shore Hardness (ASTM D-2240) 80 D Shrinkage (in./in.) .003 Tensile Strength (ASTM D-638)(psi) 8,000 Elongation (in./in.) 1-3% Temp Resistance n/a    * Item cannot be returned or exchanged

Read more less

Alumilite White (also known and sold as Amazing Casting Resin) is an easy to use white urethane resin that creates a durable casting with perfect cosmetics and intricate details. Transitions from clear to opaque white when curing Easily dyed or painted   Technical Data Sheet Safet Data Sheet TECHNICAL SPECIFICATIONS Product: Alumilite White Color: White Mix Ratio: 1:1 by weight or volume Pot Life: 2 minutes Demold Time (100 gram mass): 5-10 minutes Mixed Viscosity (cps): 90 Specific Gravity: 1.05 Shore Hardness (ASTM D2240): 72 D Shrinkage (in./in.): .006 Tensile Strength (ASTM D638, psi): 4500 Elongation (in./in.): 10% Temperature Resistance: 185º F

Read more less

Use Alumilite’s Dyes to color your casting resin. Can be used in the water clear resin to make a translucent colored casting. The dyes are added to the “A” side by weight up to 5%. Use the Flesh tones according to your preference of shade (flesh tones are typically used in Alumilite White to achieve the best results). NOTE: 1 oz. bottle dispensing tip must be cut to dispense dye. Tip may also be removed completely.   Disclaimer: Bottle style/label may vary from what is pictured due to mfr. labeling update. Otherwise it is still the same product.  

Read more less

High Pressure Wood Stabilizing Chamber A BVV EXCLUSIVE! This is our high pressure wood stabilizing column that can perform rapid wood stabilization @ 1600 PSI (1.5" Diameter Tube) & 450 PSI (3"/ 6" Diameter Tube).  This extreme pressure makes the toughest woods easy to impregnate with wood stabilizer in as little as 15min.  Then its off to the oven for a quick cure and its finished.  The blanks in the photo, all 3 were stabilized and cured in less than 1 hour and 15 min, including cleanup.  The system is simple.  Load your blanks into the column and fill no more than 80% with resin.  (make sure the blanks are submerged) Then close the system and turn on the pump set to 1600 psi.   Watch the video and check out the instruction manual for details.  High Pressure Wood Stabilizing Manual with Assembly The compressor you will need can be ordered from this site (GX Pumps Click This Link).  BVV does not yet carry the compressor for this system.  But our hose will connect directly to the compressor. If the compressor is out of your reach a high pressure hand pump can be used. (GX Hand Pumps Click This Link) The system comes with an installed safety pressure relief burst disk rated for 1800 PSI. (1.5" Diameter tubes)  & 450 PSI. (3"/ 6" Diameter tube) Should you exceed the pressure of the system the disk will rupture releasing pressure.   What's Included Wood stabilizing manual *Coming Soon 3/1/24 for 3"/ 6" Diameter. Braided stainless steel hose 2500 psi rated. Main column, stand and top cap valve manifold assembled. Extra safety burst disk, for 1.5" Diameter Tube.  3"/ 6" Tubes self reset.  BVV warranties the main column to be free from any defects for 1 year. All other individual components may hold separate warranty periods. BVV does not warranty any claims where resin has been released/backflowed into the manifold hose or valve.  Resin is water washable and should be cleaned after each use, especially if resin has accidentally backflowed into the manifold area.

Read more less