C1D1 Booths

PBS Industries EXT8810 Extraction Room PBS Industries, LLC is pleased to offer the following proposal for your consideration. (1) Model EXT8810 Extraction Room Interior working dimensions: 8'-0" wide X 8'-0" tall X 10'-0" long. Approximate overall dimensions: 8'-4" wide X 8'-2" tall X 12'-4" long.   Scope: Clean air flows into the room through the filtered ceiling at the front, passing through the work area, and exits through the exhaust plenum located in the rear of the room. Air is drawn through the exhaust plenum and discharged upward into the atmosphere via the exhaust stack(s).   Panels: Panels are fabricated from 18-gauge quality galvanized steel, flanged and precision punched on 6" centers. Panels are fastened together with 5/16 bolts for maximum rigidity. Panel seams and any penetration holes added for extraction equipment must be sealed with provided non-flammable caulk. Meets ATMC-838 Specifications.   A total of (1) Explosion Proof light fixtures will be provided for illumination: Lighting is provided by 4’ long, 3-Row, 68 watt, LED fixture. Fixture is rated for Class I Div. 1 area (Explosion Proof) group C and D. All fixtures are UL844 listed and approved for their intended use and placement. Fixtures are supplied with 120V-277V power, diffused optic, powder coated black, and carry a 5-year limited warranty.   (1) - 18” .75 HP Exhaust fan rated for 2,000 CFM @ 0.5” Static Pressure Total CFM exhausted: 2,000 CFM. (UL Listed, Explosion Proof Motor) A precision balanced, fabricated, tube axial type duct fan with aluminum non-sparking fan blade moves air through the fan. Bearings are mounted in rubber isolators for smooth operation. The motor, drive, and bearings are isolated from the exhaust air stream. The bearings are sized with a minimum average life, per AFBMA, in excess of 200,000 hours when operating at the maximum RPM of the fan size.   Design Note: Purge air flow is calculated at approximately 3 air changes per minute. Constant operational airflow is approximately 800-1000 CFM.   Infrared Gas Detection System:Control panel is housed in a NEMA 4X enclosure that is waterproof, chemical, and weather resistant. The control box includes an audible and visual alarm to alert personnel of gas detection including gas type and concentration level. When gas is detected above the appropriate setting the exhaust fan will increase to full speed to purge gas from the room. UL Listed infrared transmitter – Detects combustibles or CO2. Sensor is pre-calibrated for your specific gas or solvent requirement. Explosion Proof Construction with non-intrusive calibration and is rated for Class 1 Div. 1 Groups B, C, D. Contact us should multiple gases or solvents be required.   (1) - Personnel access door(s): Personnel access door(s) are double wall 18-Ga. galvanized steel units sized at 36" x 84” and are provided pre-hung in a heavy gauge steel frame ready for mounting to the room. The mounting hardware includes an observation window, FM approved panic type safety latch and two 6" door pulls. Room also includes a door closing device that is UL Listed and ADA compliant. Closer can be mounted on the interior or exterior as well as the left or right side of the door. Door closer is constructed of aluminum and is ANSI A156.4 compliant.   UL/ ETL Listed Control Equipment: A NEMA12 enclosure pre-wired and tested by manufacturer for simple hookup. Control panel includes main disconnect switch, class 10 motor protection, light contactor, fuse block, and field wiring terminal strip to easily connect interlock circuits such as door limit switches, and fire suppression. Includes fan failure alarm circuit and auto fan override relay. The class 10 motor protector offers maximum motor protection by being individually calibrated for the smallest and largest current it can handle and includes automatic ambient temperature compensation over a range of -13F to +140F. Code Compliance: All PBS extraction rooms are designed to meet or exceed the requirements and recommendations of the National Fire Protection Association (NFPA), Codes: NFPA 1-2018, 33, 55-2016, 58-2020, 70-2017, 497-2017. NEMA 250-2018. ASME BPVC VIII Div. 1-2019, IBC. IFC-2018. IMC as well as the Occupational Health and Safety Administration (OSHA) CFR 29.1910.107 covering the operation and construction of ventilated rooms. All PBS extraction rooms are peer reviewed and UL 1389 compliant with regard to component operation, placement and intended use. ​ All PBS extraction rooms are designed to meet or exceed the requirements and recommendations of the National Fire Protection Association (NFPA), Codes: NFPA 1-2018, 33, 55-2016, 58-2020, 70-2017, 497-2017. NEMA 250-2018. ASME BPVC VIII Div. 1-2019, IBC. IFC-2018. IMC as well as the Occupational Health and Safety Administration (OSHA) CFR 29.1910.107 covering the operation and construction of ventilated rooms. All PBS extraction rooms are peer reviewed and UL 1389 compliant with regard to component operation, placement and intended use. ​    NOTE PLEASE: If you would like more than one ADD-on please contact us   

Read more less

PBS Industries EXT10812 Extraction Room   PBS Industries, LLC is pleased to offer the following proposal for your consideration. (1) Model EXT10812 l Extraction Room Interior working dimensions: 10'-0" wide X 8'-0" tall X 12'-0" long. Approximate overall dimensions: 10'-4" wide X 8'-2" tall X 14'-4" long.   Scope: Clean air flows into the room through the filtered ceiling at the front, passing through the work area, and exits through the exhaust plenum located in the rear of the room. Filtered exhaust air is drawn through the exhaust plenum and discharged upward into the atmosphere via the exhaust stack(s).   Panels: Panels are fabricated from 18-gauge quality galvanized steel, flanged and precision punched on 6" centers. Panels are fastened together with 5/16 bolts for maximum rigidity. Panel seams and any penetration holes added for extraction equipment must be sealed with provided non-flammable caulk. Meets ATMC-838 Specifications.   A total of (1) Explosion Proof light fixtures will be provided for illumination: Lighting is provided by 4’ long, 3-Row, 68 watt, LED fixture. Fixture is rated for Class I Div. 1 area (Explosion Proof) group C and D. All fixtures are UL844 listed and approved for their intended use and placement. Fixtures are supplied with 120V-277V power, diffused optic, powder coated black, and carry a 5-year limited warranty. (1) - 18” .75 HP Exhaust fan rated for 3,000 CFM @ 0.5” Static Pressure Total CFM exhausted: 3,000 CFM. (UL Listed, Explosion Proof Motor) A precision balanced, fabricated, tube axial type duct fan with aluminum non-sparking fan blade moves air through the fan. Bearings are mounted in rubber isolators for smooth operation. The motor, drive, and bearings are isolated from the exhaust air stream. The bearings are sized with a minimum average life, per AFBMA, in excess of 200,000 hours when operating at the maximum RPM of the fan size.   Design Note: Purge air flow is calculated at approximately 3 air changes per minute. Constant operational airflow is approximately 800-1000 CFM.   Infrared Gas Detection System: Control panel is housed in a NEMA 4X enclosure that is waterproof, chemical and weather resistant. The control box includes an audible and visual alarm to alert personnel of gas detection including gas type and concentration level. When gas is detected above the appropriate setting the exhaust fan will increase to full speed to purge gas from the room. UL Listed infrared transmitter – Detects combustibles or CO2. Sensor is pre-calibrated for your specific gas or solvent requirement. Explosion Proof Construction with non-intrusive calibration and is rated for Class 1 Div. 1 Groups B, C, D. Contact us should multiple gases or solvents be required.   (1) - Personnel access door(s): Personnel access door(s) are double wall 18-Ga. galvanized steel units sized at 36" x 84” and are provided pre-hung in a heavy gauge steel frame ready for mounting to the room. The mounting hardware includes an observation window, FM approved panic type safety latch and two 6" door pulls. Room also includes a door closing device that is UL Listed and ADA compliant. Closer can be mounted on the interior or exterior as well as the left or right side of the door. Door closer is constructed of aluminum and is ANSI A156.4 compliant.   UL/ ETL Listed Control Equipment: A NEMA12 enclosure pre-wired and tested by manufacturer for simple hookup. Control panel includes main disconnect switch, class 10 motor protection, light contactor, fuse block, and field wiring terminal strip to easily connect interlock circuits such as door limit switches, and fire suppression. Includes fan failure alarm circuit and auto fan override relay. The class 10 motor protector offers maximum motor protection by being individually calibrated for the smallest and largest current it can handle and includes automatic ambient temperature compensation over a range of -13F to +140F.   Code Compliance: All PBS extraction rooms are designed to meet or exceed the requirements and recommendations of the National Fire Protection Association (NFPA), Codes: NFPA 1-2018, 33, 55-2016, 58-2020, 70-2017, 497-2017. NEMA 250-2018. ASME BPVC VIII Div. 1-2019, IBC. IFC-2018. IMC as well as the Occupational Health and Safety Administration (OSHA) CFR 29.1910.107 covering the operation and construction of ventilated rooms. PBS extraction rooms are UL 1389 compliant with regard to component placement, operation, and intended use. Peer Review included.   NOTE PLEASE: If you would like more than one ADD-on please contact us 

Read more less

  PBS Industries EXT10815 Extraction Room   (1) Model EXT10815 Extraction Room Interior working dimensions: 10'-0" wide X 8'-0" tall X 15'-0" long. ​ Approximate overall dimensions: 10'-4" wide X 8'-2" tall X 17'-4" long.   Scope: Clean air flows into the room through the filtered ceiling at the front, passing through the work area, and exits through the exhaust plenum located in the rear of the room. Air is drawn through the exhaust plenum and discharged upward into the atmosphere via the exhaust stack(s).   Panels: Panels are fabricated from 18-gauge quality galvanized steel, flanged and precision punched on 6" centers. Panels are fastened together with 5/16 bolts for maximum rigidity. Panel seams and any penetration holes added for extraction equipment must be sealed with provided non-flammable caulk. Meets ATMC-838 Specifications. ​ A total of (3) Explosion Proof light fixtures will be provided for illumination: Lighting is provided by 48" long, 3-row, 73 watts, C1D1 LED lights. Fixtures are rated for Class I Div. 1 area (Explosion Proof) group C and D. All fixtures are UL844 listed and approved for their intended use and placement. Lights will accept either 120V or 277V power and carries a 5-year limited warranty. ​ (1) - 18” 1.5 HP Exhaust fan rated for 4,000 CFM @ 0.5” Static PressureTotal CFM exhausted: 4,000 CFM. (UL Listed, Explosion Proof Motor) A precision balanced, fabricated, tube axial type duct fan with aluminum non-sparking fan blade moves air through the fan. Bearings are mounted in rubber isolators for smooth operation. The motor, drive, and bearings are isolated from the exhaust air stream. The bearings are sized with a minimum average life, per AFBMA, in excess of 200,000 hours when operating at the maximum RPM of the fan size ​ Design Note: Air flow is calculated at approximately 3 air changes per minute. ​ Infrared Gas Detection System: Control panel is housed in a NEMA 4X enclosure that is waterproof, chemical and weather resistant. The control box includes an audible and visual alarm to alert personnel of gas detection including gas type and concentration level. When gas is detected above the appropriate setting the exhaust fan will increase to full speed to purge gas from the room. UL Listed infrared transmitter – Detects combustibles and CO2. Explosion Proof Construction with non-intrusive calibration and is rated for Class 1 Div. 1 Groups B, C, D. ​ (1) - Personnel access door(s): Personnel access door(s) are double wall 18-Ga. galvanized steel units sized at 36" x 84” and are provided pre-hung in a heavy gauge steel frame ready for mounting to the room. The mounting hardware includes an observation window, FM approved panic type safety latch and two 6" door pulls. Room also includes a door closing device that is UL Listed and ADA compliant. Closer can be mounted on the interior or exterior as well as the left or right side of the door. Door closer is constructed of aluminum and is ANSI A156.4 compliant. ​ UL/ ETL Listed Control Equipment: A NEMA12 enclosure pre-wired and tested by manufacturer for simple hookup. Control panel includes main disconnect switch, class 10 motor protection, light contactor, fuse block, and field wiring terminal strip to easily connect interlock circuits such as door limit switches, and fire suppression. Includes fan failure alarm circuit and auto fan override relay. The class 10 motor protector offers maximum motor protection by being individually calibrated for the smallest and largest current it can handle and includes automatic ambient temperature compensation over a range of -13F to +140F. ​ Code Compliance: All PBS extraction rooms are designed to meet or exceed the requirements and recommendations of the National Fire Protection Association (NFPA), Codes: NFPA 1-2018, 33, 55-2016, 58-2020, 70-2017, 497-2017. NEMA 250-2018. ASME BPVC VIII Div. 1-2019, IBC. IFC-2018. IMC as well as the Occupational Health and Safety Administration (OSHA) CFR 29.1910.107 covering the operation and construction of ventilated rooms. All PBS extraction rooms are peer reviewed and UL 1389 compliant with regard to component operation, placement and intended use.

Read more less

PBS Industries EXT101012 Extraction Room (1) Model EXT101012 Extraction Room Interior working dimensions: 10'-0" wide X 10'-0" tall X 12'-0" long. ​ Approximate overall dimensions: 10'-4" wide X 10'-2" tall X 14'-4" long. ​ Scope: Clean air flows into the room through the filtered ceiling at the front, passing through the work area, and exits through the exhaust plenum located in the rear of the room. Air is drawn through the exhaust plenum and discharged upward into the atmosphere via the exhaust stack(s). ​ Panels: Panels are fabricated from 18-gauge quality galvanized steel, flanged and precision punched on 6" centers. Panels are fastened together with 5/16 bolts for maximum rigidity. Panel seams and any penetration holes added for extraction equipment must be sealed with provided non-flammable caulk. Meets ATMC-838 Specifications. ​ A total of (2) Explosion Proof light fixtures will be provided for illumination: Lighting is provided by 48" long, 3-row, 73 watts, C1D1 LED lights. Fixtures are rated for Class I Div. 1 area (Explosion Proof) group C and D. All fixtures are UL844 listed and approved for their intended use and placement. Lights will accept either 120V or 277V power and carries a 5-year limited warranty. ​ (1) - 18” 1.5 HP Exhaust fan rated for 4,000 CFM @ 0.5” Static PressureTotal CFM exhausted: 4,000 CFM. (UL Listed, Explosion Proof Motor) A precision balanced, fabricated, tube axial type duct fan with aluminum non-sparking fan blade moves air through the fan. Bearings are mounted in rubber isolators for smooth operation. The motor, drive, and bearings are isolated from the exhaust air stream. The bearings are sized with a minimum average life, per AFBMA, in excess of 200,000 hours when operating at the maximum RPM of the fan size. ​ Design Note: Air flow is calculated at approximately 3 air changes per minute. ​ Infrared Gas Detection System: Control panel is housed in a NEMA 4X enclosure that is waterproof, chemical and weather resistant. The control box includes an audible and visual alarm to alert personnel of gas detection including gas type and concentration level. When gas is detected above the appropriate setting the exhaust fan will increase to full speed to purge gas from the room. UL Listed infrared transmitter – Detects combustibles and CO2. Explosion Proof Construction with non-intrusive calibration and is rated for Class 1 Div. 1 Groups B, C, D. ​ (1) - Personnel access door(s): Personnel access door(s) are double wall 18-Ga. galvanized steel units sized at 36" x 84” and are provided pre-hung in a heavy gauge steel frame ready for mounting to the room. The mounting hardware includes an observation window, FM approved panic type safety latch and two 6" door pulls. Room also includes a door closing device that is UL Listed and ADA compliant. Closer can be mounted on the interior or exterior as well as the left or right side of the door. Door closer is constructed of aluminum and is ANSI A156.4 compliant. ​ UL/ ETL Listed Control Equipment: A NEMA12 enclosure pre-wired and tested by manufacturer for simple hookup. Control panel includes main disconnect switch, class 10 motor protection, light contactor, fuse block, and field wiring terminal strip to easily connect interlock circuits such as door limit switches, and fire suppression. Includes fan failure alarm circuit and auto fan override relay. The class 10 motor protector offers maximum motor protection by being individually calibrated for the smallest and largest current it can handle and includes automatic ambient temperature compensation over a range of -13F to +140F. ​ Code Compliance: All PBS extraction rooms are designed to meet or exceed the requirements and recommendations of the National Fire Protection Association (NFPA), Codes: NFPA 1-2018, 33, 55-2016, 58-2020, 70-2017, 497-2017. NEMA 250-2018. ASME BPVC VIII Div. 1-2019, IBC. IFC-2018. IMC as well as the Occupational Health and Safety Administration (OSHA) CFR 29.1910.107 covering the operation and construction of ventilated rooms. All PBS extraction rooms are peer reviewed and UL 1389 compliant with regard to component operation, placement and intended use.  

Read more less

Advanced Extraction Labs Micro Series C1D1 Indoor Booth Micro Series This advanced extraction labs is designed for small to medium-level extraction production businesses, the walk-in style for C1D1 indoor baths or C1D2 environments, for those using ethanol, post-extraction process, and various solvents. ***Note: C1D2 option, Duct Package, Mechanical Installation, Fire suppression, and Electrical Installation available upon request.   

Read more less

Advanced Extraction Labs Mega Economy Series C1D1 Indoor booth Mega Economy Series The Mega Economy series advanced extraction labs are the only choice for an affordable, functional lab. This unit is turnkey and ready to go, equipped with everything you need, from safety features to gas detection. Labs can be configured to meet your needs! This booth is legitimate if you're just starting out in the Extraction business with C1D1. All the trimmings you're going to need at a one-time cost. You buy it; you start using it. We're experts at setting these up to meet your requirements. Call us, and we'll walk you through this from start to finish. ***Note: C1D2 option, Duct Package, Mechanical Installation, Fire suppression, and Electrical Installation available upon request. 

Read more less

Advanced Extraction Labs Mega Deluxe Series C1D1 Indoor Booth Mega Deluxe Series The Mega Deluxe series extraction lab is made for medium to large extraction environments. These labs are modular and can be disassembled and reassembled with ease. They are fully equipped and come with an optional permit package, too. ***Note: C1D2 option, Duct Package, Mechanical Installation, Fire suppression, and Electrical Installation available upon request. 

Read more less

Advanced Extraction Labs DYS Economy Series C1D1 Indoor Booth DYS Series DYS Series advanced extraction labs are our most economical model, and they are made without compromising product quality. These C1D1 booth Labs come fully equipped with all necessary gas detection and safety features, high-efficiency filtration, and a variety of sizes. ***Note: C1D2 option, Duct Package, Mechanical Installation, Fire suppression, and Electrical Installation available upon request. 

Read more less

Advanced Extraction Labs EXXA Series C1D1 Indoor Booth Exxa Series Exxa Series is the perfect choice for labs with a high output. This Advanced Extraction Labs unit is made with accessibility and safety in mind. Our large front doors are ideal for moving equipment in and out of the c1d1 extraction booth. This lab is compatible with all extraction types and can be made into a dual-zone environment. This lab has all safety and gas detection systems and can be made in multiple configurations to best suit your needs. One of our larger extraction booths, our Exxa series is a C1D1 Extraction lab and can be used for CBD, THC, and various other extraction types. These labs are modular and can be expanded.    ***Note: C1D2 option, Duct Package, Mechanical Installation, Fire suppression, and Electrical Installation available upon request. 

Read more less

Advanced Extraction Labs ZETA Extra Large Series C1D1 Indoor Booth Zeta Labs Indoor Booth Series Zeta advanced extraction labs are the largest size and are made to handle large extraction environments. Regarding big XL labs and extraction systems, the Zeta Series lab is up to the task.  These units can be as large as you can imagine and come in many configurations. Like our other modular units, these units are expandable and can be made larger anytime. These labs come fully equipped and can be used for CBD, THC, and various other extraction types. ***Note: C1D2 option, Duct Package, Mechanical Installation, Fire suppression, and Electrical Installation available upon request. 

Read more less