Fire Sale Stainless Steel Parts

26 products


  • SSP - Male Elbow Shop All Categories SSP Corporation 1/4-inch

    Male Elbow

    SSP - Male Elbow SSP Instrumentation TruFit® is manufactured from fully-traceable raw material to close tolerances and superior surface finishes. TruFit® provides optimal performance when installed in accordance with SSP’s recommendations and the design parameters appropriate for each type of connection – tapered thread, straight thread, and weld & braze. TruFit® components are cleaned in accordance with SSP documented work instructions using equipment calibrated to NIST standards with environmentally-safe and stable agents, ultrasonics, and heat/ temperature to remove all residual oil, grease, and loose particles. Stainless steel components are passivated to the requirements of MIL QQ-P-35 and ASTM A 967.   ***Note: ALL NPT Threads REQUIRE the user to properly install the fitting by using a thread sealant to prevent leaks. Best Value Vacs recommends GAS PTFE Tape Specifications Connection Type 1 Male NPT Connection Size 1 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Working Pressure (PSIG) 1/4" - 7750 3/8" - 6800 NPT Pressure Rating >10,000PSI ASME B31.3     SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!

  • SSP - Port Connector Shop All Categories SSP Corporation 1/4-inch

    Port Connector - 3/8" X 1/4"

    SSP - Port Connector - 3/8" X 1/4" SSP Instrumentation Duolok® tube fittings are designed, manufactured and quality controlled to be totally “interchangeable” with the Swagelok® brand of tube fittings. Component by component examination plainly shows the two brands as completely “componentintermixable.” The precision manufacturing of both products to stringent tolerances under rigid quality control procedures ensures the safety, performance, and reliability of service whenever Duolok® and Swagelok® component parts are mixed and used in accordance with published installation and service recommendations.   Specifications Connection Type 1 Duolok Tube Fitting Connection Size 1 NLT 99.5% Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Duolok Pressure Rating = Tubing Rating       SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!

    $8.00

  • Sale -36% Gold High Pressure Clamps Shop All Categories BVV 1.5-inch

    Gold High Pressure Clamps

    Gold High-Pressure Clamps     These are the Best Value Vacs faux Gold Plated high-pressure clamps that provide the user with visual wear indicators for the bolts and clamps allowing the user to notice when the clamp is needed to be replaced. It also adds an awesome amount of bling to your system. Fits Tri-clamp Flange fittings.   Best Value Vacs recommends tightening all High Pressure to their specified LBS of torque. We do not recommend tightening high-pressure bolts with an impact gun because this may cause threads to jump or be marred which can cause failure of the bolt or seal. Sizes Available: 1.5" High Pressure Clamp 2" High Pressure Clamp 3" High Pressure Clamp 4" High Pressure Clamp 6" High Pressure Clamp 8" High Pressure Clamp 10" High Pressure Clamp 12" High Pressure Clamp Specifications: Hinge Type: Bolted Material: 304 Stainless Steel with faux gold coating Connection Type: Tri-Clamp Sizes Max Torque (Nm / Ft Lbf / In Lbf) Maximum Pressure @70F Maximum Pressure @250F 1.5" 12-14 / 8.85-10 / 106-124 1500 1200 2" 12-14 / 8.85-10 / 106-124 1000 800 3" 12-14 / 8.85-10 / 106-124 1000 800 4" 12-14 / 8.85-10 / 106-124 600 800 6" 12-14 / 8.85-10 / 106-124 300 200 8" 12-14 / 8.85-10 / 106-124 250 150 10" 12-14 / 8.85-10 / 106-124 200 125 12" 12-14 / 8.85-10 / 106-124 150 100

    $16.00 - $45.00

  • Sale -28% 1LB CO2 Spool - 316SS Shop All Categories BVV

    1LB CO2 Spool - 316SS

    1LB CO2 Spool - 316SS This double wellhead CO2 spool is designed for extreme pressure applications and is made of 316 Stainless Steel. Its maximum working pressure is 6000PSI and comes with a welded on outer jacket to circulate temperature regulating fluid through and maintain a consistent temperature. This spool also has welded brackets to allow the user to attach to a rack system or other mounting surface. Specifications: Material: 316 Stainless Steel Working Pressure: 6000PSI Connection Type: Hammer Union Gasket Material: NBR Wellhead Diameter: 3" Length: 28" End Cap Ports: 1/4" FNPT Jacketed Ports: 1/2" FNPT  

    $900.00$650.00

  • Sale -33% 2LB CO2 Spool - 316SS Shop All Categories BVV

    2LB CO2 Spool - 316SS

    2LB CO2 Spool - 316SS This double wellhead CO2 spool is designed for extreme pressure applications and is made of 316 Stainless Steel. Its maximum working pressure is 6000PSI and comes with a welded on inner jacket to circulate temperature regulating fluid through and maintain a consistent temperature and also a welded on exterior double jacket to create a vacuum and increase temperature stability even further. This spool also has welded brackets to allow the user to attach to a rack system or other mounting surface. Specifications: Material: 316 Stainless Steel Working Pressure: 6000PSI Connection Type: Hammer Union Gasket Material: NBR Wellhead Diameter: 4" Length: 28" End Cap Ports: 1/4" FNPT Jacketed Ports: 1/2" FNPT  

    $1,500.00$1,000.00

  • Sale -60% Mini CO2 Spool - 316SS Shop All Categories BVV

    Mini CO2 Spool - 316SS

    Mini CO2 Spool - 316SS This double wellhead CO2 spool is designed for extreme pressure applications and is made of 316 Stainless Steel. Its maximum working pressure is 6000PSI, Specifications: Material: 316 Stainless Steel Working Pressure: 6000PSI (Hydrostatic pressure tested & serialized)  Connection Type: Hammer Union Gasket Material: NBR Wellhead Diameter: 2" (Inside Diameter)  Length: 19" (inside Length 12") End Cap Ports: 1/4" FNPT 2x end cap filters (stainless steel sintered disc 40 micron)  

    $550.00$220.00

  • 8" Tri-Clamp Dewaxer Column Shop All Categories BVV 36-inch

    8" Tri-Clamp Dewaxer Column

    8" Tri-Clamp/ Tri Clover Dewaxing Columns   This is a 8" Tri-Clamp BVV™ Tri-Clamp Dewaxing Spool. It is intended to have dry ice put into the sleeve to chill the material inside the column. **Note: When selecting a Pipe Hanger choose the size that correlates to the Sleeve OD NOT Spool OD Sizes Available: 8" x 36" Tri-clamp Dewaxer Column 8" x 48" Tri-clamp Dewaxer Column Specifications: Tri-Clamp Size 8" Material 304 Stainless Steel Standard 3A High Polish Sleeve OD 10.000" Spool ID 7.782" Spool OD 8.000" Flange OD 8.570" Bead Center 8.150" Drain Port 1/4"-18 FNPT (Drain Plug Included)   OD = Outer Dimension ID = Inner Dimension Disclaimer to Customer: User assumes all responsibility and risks of the system for all Stainless Steel Parts bought separately to piece together a Closed Loop, Closed Column, or Open Blast Extractors. They DO NOT come with a standard 1 year system warranty, customer assistance on how to run your system, technical help or a guarantee of the system being tested. BVV™ 8" Tri-Clamp Dewaxer Columns - Drawing  

    $500.00 - $600.00

  • Tri-Clamp Ferrule Shop All Categories BVV 1.5-inch

    Tri-Clamp Ferrule

    Tri-Clamp/ Tri Clover Ferrule Tri-clamp ferrules are the bottom of our open blast systems. These ferrules allow the user to use a screened gasket at the end of an open blast spool while providing an open end. Specifications: Material: 304 Stainless Steel Connection Type: Tri-Clamp Standard: 3A Sizes Available: 1.5" 2" 3"    

    $6.00 - $8.00

  • SSP - Street Tee Shop All Categories SSP Corporation 1/4-inch

    Street Tee

    SSP - Street Tee SSP Instrumentation TruFit® is manufactured from fully-traceable raw material to close tolerances and superior surface finishes. TruFit® provides optimal performance when installed in accordance with SSP’s recommendations and the design parameters appropriate for each type of connection – tapered thread, straight thread, and weld & braze. TruFit® components are cleaned in accordance with SSP documented work instructions using equipment calibrated to NIST standards with environmentally-safe and stable agents, ultrasonics, and heat/ temperature to remove all residual oil, grease, and loose particles. Stainless steel components are passivated to the requirements of MIL QQ-P-35 and ASTM A 967.   ***Note: ALL NPT Threads REQUIRE the user to properly install the fitting by using a thread sealant to prevent leaks. Best Value Vacs recommends GAS PTFE Tape Specifications Connection Type 1 Female NPT Connection Size 1 Specified by User Connection Type 2 Female NPT Connection Size 2 Specified by User Connection Type 3 Male NPT Connection Size 3 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Working Pressure (PSIG) 1/4" - 7750 3/8" - 6800 NPT Pressure Rating >10,000PSI ASME B31.3   SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!

    $35.00 - $40.00

  • Sale -38% Butterfly Valve - 316 Stainless - VITON Seals New Products BVV 1-inch

    Butterfly Valve - 316 Stainless - VITON Seals

    Butterfly Valve - 316 Stainless Steel - VITON Seals Butterfly Valve - 316 Stainless Steel  VITON Seals is a valve that isolates or regulates the flow of a fluid. The closing mechanism is a disk that rotates Properties: Tri-Clamp / Tri Clover Sanitary butterfly valve 4 positions pull handle Stainless steel 316 Viton seal Meets 3 A Standard Operating Temperature: 15º F to 200º F   Gasket Properties VITON Heat resistant Excellent (400°F) Cold resistant Good-Excellent (-30°F) Steam Excellent Abrasion-resistant Good Alkali Poor-Good Acid resistance Good Vegetable oil Excellent Petroleum oil Excellent Oxonia Excellent

    $30.00 - $65.00

  • Mastercool 1/4" FNPT Vacuum Pump Exhaust Adapter Shop All Categories BVV

    Mastercool 1/4" FNPT Vacuum Pump Exhaust Adapter

    Mastercool 1/4" FNPT Vacuum Pump Exhaust Adapter This fitting allows the user to connect a 1/4" NPT fitting to the exhaust for the desired application such as a carbon exhaust filter. It is made of brass and comes with a Viton O-ring.

    $10.00

  • 3/4" 37 Degree x 48" Length JIC Stainless Steel Hose Shop All Categories BVV

    3/4" 37 Degree x 48" Length JIC Braided Stainless Steel Hose

    3/4" 37 Degree JIC Braided Stainless Steel Hose These chemically resistant PTFE braided hoses are a necessity when dealing with harsh chemicals or solvents and high-pressure applications. They provide a uniquely rugged, durable, and chemically resistant combination of Stainless Steel and PTFE by having an inner core of PTFE and protecting that with a braided stainless steel outer sleeve. These hoses have female JIC swivel on each end and they DO NOT require Teflon tape to create a seal and they should always be tightened and untightened using 2 wrenches. ***Note: Do not exceed the specified hose bend radius or the inner PTFE liner will kink and the hose integrity will become compromised and should not be used. Specifications: Connection Type(s): 3/4" 37° Female JIC Swivel (1 1/16"-12) Liner Material PTFE (Teflon) Braid Material 304 Stainless Steel Swivel Material 304 Stainless Steel Temperature Rating -65° to 450°F Pressure Rating 1200 PSI Chemical Resistance Excellent Max Bend Radius 7-3/4"

    $160.00

  • Sale -23% Nai-Lok - Adjustable Pressure Relief Valve Shop All Categories Nai-Lok 10-250 PSIG

    Nai-Lok - Adjustable Pressure Relief Valve

    Nai-Lok - Adjustable Pressure Relief Valve. 1/4" MNPT Inlet x 1/4" FNPT Outlet made out of 316 Stainless Steel

    $110.00$85.00

  • Sale -36% 3 Piece Heavy Duty Tri-Clamp 304SS Shop All Categories BVV 1.5-inch

    3 Piece Heavy Duty 8" Tri-Clamp 304SS

    3 Piece Heavy Duty Tri-Clamp/Tri Clover 304SS This 3 Piece Heavy Duty Tri-Clamp is made out of 304 stainless steel and has a 3 segment locking function allowing even pressure around the connection point gasket so it does not bulge out in a certain direction creating a better overall seal on the system. This clamp will fit a standard 8" tri-clamp connection    

    $140.00$90.00

  • Sale -20% Sanitary 3-Way Ball Valve Shop All Categories BVV

    Sanitary 3-Way Ball Valve 4" Tri-Clamp

    Sanitary 3-Way Ball Valve These 3 way ball valves are typically used to drain a system that needs to be routed to multiple different places. The internal ball is an L shape meaning that the middle port should be used as the in and it can be routed to the left or right port. The valve can also be closed off so that the liquid will not move any direction. It can be easily attached to any system using Tri-Clamp flanges. Housing Material: 304 SS Seat Material: PTFE Temperature Range: 0-100°C

    $750.00$600.00

  • Sale -61% 5 Micron Stainless Steel Sintered Filter Disk with Viton O-ring  1.5-inch

    5 Micron Stainless Steel Sintered Filter Plate with Viton O-ring

    5 Micron Stainless Steel Sintered Filter Disk with Viton O-ring What is a 5 Micron Stainless Steel Sintered Filter Disk With Viton O-Ring? BVV™ has custom-designed a 5 Micron Stainless Steel Sintered Filter Disk With Viton O-Ring fit to provide you with extreme levels of filtration or refinement. The stainless steel material can stand up to high pressure without tearing or ripping like regular paper filtration media, but, we recommend you use it with a  filter paper on top to prevent clogging and maintain its longevity. Offered as a la carte parts, each of these 5 Micron Stainless Steel Sintered Filter Disks has a Viton O-ring around their outer edges for a snug fit within our Tri-Clamp Spools. This allows you to pressurize the system and force a faster filtration rate than what it was previously capable of.  The Benefits of 5 Micron Stainless Steel Sintered Filter Disk With Viton O-Ring You can’t go wrong with this filter disk model: it successfully combines precise permeability with a high dirt-holding capacity. This means its filtration rate will be accurate whether it’s running at a steady pace or a quicker one. It’s also highly resistant to elevated pressure, temperatures, acidity, and alkalinity, as well as corrosion and abrasion.  The impressive rigidity and stability of the 5-micron stainless steel sintered filter disk with a Viton O-ring gives it a longer length of service than other mediums. Meanwhile, its surface makes it reusable through a simple wash, saving you a lot of time and money over the course of its life. Product Uses Stainless steel sintered filter disks are perfect for advanced screening and refinement processing in a wide variety of application methods. They have been used to desalinate seawater for drinking purposes and sterilize air filtration in breweries. You can find them mixing and purifying gas in chemical fiber as well as filtering pressurized gas for aviation and transportation industries and catalytic gas for the oil industry. Sintered metal filter discs can also remove dust, corrosive liquid, and gases; and perform precious metal catalyst recovery, steam processing, and gas-liquid sparging. See additional industrial sectors disks like these are used in below: Electronics Petroleum and Petrochemical Chemicals Plastics Automotive Environmental Protection Metallurgy Sewage Treatment Pharmaceutical Natural Remedies Food and Beverage Shop all filtration equipment on BVV  

    $89.00 - $230.00

  • SSP - 2 Way Ball Valve - Fractional Tube Fitting Shop All Categories SSP Corporation 1/4-inch

    2 Way Ball Valve - Fractional Tube Fitting

    SSP - 2 Way Ball Valve - Fractional Tube Fitting SSP Instrumentation Flolok® manually operated two-way ball valves provide quick ¼ turn directional flow control of fluids in instrumentation and process systems. Features: Directional handle indicates flow direction Panel Mountable 90-degree actuation Straight through flow path Micro-finished ball provides positive seal Free-floating ball design provides compensation for seat wear for repetitive sealing Blow-out proof ball & stem Standard Product Testing - Every ball valve is assembled and tested @ 1000 psi (68.9 bar) with Nitrogen   Specifications Body Material 316 Stainless Steel Pressure Rating @ 100F 3000 PSIG @37C 208 BAR @300F 2500 PSIG @148C 172 BAR Connection Type 1 Duolok Tube Fitting Connection Size 1 Specified by User Connection Type 2 Duolok Tube Fitting Connection Size 2 Specified by User Handle Type Nylon-Stainless Steel Insert Handle Color Black Packing Material PTFE   SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!

    $120.00 - $300.00

  • Sale -22% 8" Hemispherical End Cap with Coil Shop All Categories BVV used with 150L-COL

    8" Hemispherical End Cap with Coil

    8" Hemispherical End Cap with Coil This 8" Hemispherical End Cap with Coil comes standard with our 150L Conical Reactor. Complete with 2X 1/2" NPT accessory ports, 2X 1/4" NPT accessory ports, 2X 1/2" NPT ports for the coil, and a single 1.5" tri-clamp top port. This versatile part is perfect for those looking to add extra surface area to their heating or cooling application.  From the 8" tri-clamp to the bottom of the coil measures 34".

    $450.00$350.00

  • EPDM Tri-Clamp Gaskets Shop All Categories BVV

    EPDM Tri-Clamp Gaskets

    EPDM Tri-Clamp Gaskets EPDM Tri-Clamp gaskets are the preferred choice of material for brewing and similar alcohol based applications. EPDM Gaskets offer a low temperature rating and have better physical properties than Viton gaskets; the best part is that they cost less than Viton and provide the same chemical resistance to many alcohols Note: EPDM is not recommended for use with hydrocarbons   Key Features: Low temperature range Low costs Better compressibility and springiness Excellent resistance to alcohols Good tear resistance Good abrasion resistance FDA CFR 177.2600 – Rubber and Rubber-Like Material for Repeated Use/Contact with Food. FDA CFR 177.1550 – Fluorocarbon Resins for Repeated Use/Contact With Food, Dairy & Pharmaceutical Products. Sizes Available: 1.5" 2" 3" 4" 6" 8" - easy on flanged 10" - easy on flanged 12" - easy on flanged   Technical Specifications: Material EPDM Color Black Connection Type Tri-Clamp Conformance FDA Compliant / Meets 3A Standards Thermal Properties: -Low Temperature Range -55°F -Minimum for Continuous Use (Static) -40°F -Brittle Point -55°F -High Temperature Range +275°F -Maximum for Continuous Use (Static) +275°F Gas Permeability Excellent Durometer or Hardness Range 65 Shore A Tensile Strength Range 200-3500PSI Elongation Range (%) 350-650% Abrasion Resistance Excellent Tear Resistance Excellent Resilience / Rebound Good Thread Style Female Chemical Compatibility: Butane D - Severe Effect Propane (liquified) D - Severe Effect Alcohols: -Amyl A - Excellent -Benzyl B - Good -Butyl B - Good -Diacetone A - Excellent -Ethyl A - Excellent -Hexyl C - Fair -Isobutyl A - Excellent -Isopropyl A - Excellent -Isopropyl A - Excellent -Methyl A - Excellent -Octyl C - Fair -Propyl A - Excellent   No more than a -40 F operating temperature should be used with EPDM. BVV is not responsible if incompatible chemicals, solvents, or operating temperatures are used in the user's system.

    $1.00 - $43.00

  • Sale -50% Light Mounted Standard Pressure Clamps Shop All Categories BVV 1.5-inch

    Light Mounted Standard Pressure Clamps

    LED Light Mounted Standard Pressure Clamps (Batteries Not Included) LED light mounted clamps offer the user convenience when trying to look into the base of their system because they don't have to fumble around and find a flashlight. These lights are directly mounted to the clamp and allow you to angle them directly into the sight glass on most of our extraction bases. Best Value Vacs recommends tightening all Standard Pressure Clamps (Non-High Pressure) to finger tight and then use either a screwdriver or wrench to tighten them 2 full turns. It is not recommended to over tighten the clamp and bottom it out as this will cause the gasket to be over-compressed and put too much tension on the clamp threads, which could cause it to fail. Sizes Available: 1.5" Standard Pressure Clamp 2" Standard Pressure Clamp 3" Standard Pressure Clamp Specifications: Hinge Type: Double/Single Material: 304 Stainless Steel Connection Type: Tri-Clamp Light Specifications: Battery Powered LED Sizes Maximum Pressure @70F (PSI) Maximum Pressure @250F (PSI) 1.5" 500 250 2" 450 250 3" 350 150

    $25.00 - $27.00

  • Sale -30% Light Mounted High Pressure Clamps Shop All Categories BVV 1.5-inch

    Light Mounted High Pressure Clamps

    High Pressure Clamps (Batteries Not Included) LED light mounted clamps offer the user convenience when trying to look into the base of their system because they don't have to fumble around and find a flashlight. These lights are directly mounted to the clamp and allow you to angle them directly into the sight glass on most of our extraction bases. Best Value Vacs recommends tightening all High Pressure to their specified LBS of torque. We do not recommend tightening high-pressure bolts with an impact gun because this may cause threads to jump or be marred which can cause failure of the bolt or seal. Sizes Available: 1.5" High Pressure Clamp 2" High Pressure Clamp 3" High Pressure Clamp Specifications: Hinge Type: Bolted Material: 304 Stainless Steel Connection Type: Tri-Clamp Light Specifications: Battery Powered LED Sizes Max Torque Maximum Pressure @70F Maximum Pressure @250F 1.5" 130 1500 1200 2" 130 1000 800 3" 130 1000 800

    $40.00$28.00

  • Sale -60% BVV Brewing SS304 Parrot Shop All Categories BVV

    BVV Brewing SS304 Parrot

    BVV Brewing SS304 Parrot  SS304 Parrot w 3/4" TC Drain Port  High quality product collector (also known as parrot or parrot body) made of stainless steel. This essential part of a still can easily be mounted with tri-clamps. Shape and angle of the product outlet take care of a clean fluid friction directly into a collection jar or funnel.   Specifications Material: Stainless Steel Weight 1.10 Height 10.11-inch Connection 1 3/4 " Tri-Clamp Connection 2 3/4 " Tri-Clamp (with 3/8" bore)

    $150.00$60.00

  • Sale -43% BVV Brewing Whiskey Helmet Shop All Categories BVV 4" X 4" TC w/1/2npt Thermo Connection

    BVV Brewing Whiskey Helmet

    BVV Brewing Whiskey Helmet  The Whiskey Helmet, onion Head comes comes with a 1/2npt Thermo connection.  Traditional whisky helmets help to blend vapors and produce a better quality products. Can work with a reflux column or as a part of pot still. Copper naturally aids the distillation, the helmet will help remove the unwanted things in alcohol vapor and bring more flavor to your final product. Sizes Available  4" x 4" Whiskey Helmet , Onion head 11L (approximately),  Pure Copper 99.99% 6" x 6" Whiskey Helmet , Onion head  30L (approximately) , Pure Copper 99.99%  

    $700.00$400.00

  • Sale -39% BVV 6" Copper Bubble Cap Plate BVV

    BVV Brewing Copper Bubble Cap Plate

    BVV Copper Bubble Cap Plate  Copper Bubble Cap Plate. These copper bubble plates are used in a flute still column positioned between sections to help with separation of alcohol and waters. The alcohol water bubbles up on the plates allowing the distiller to see the action happening in the still column. More bubble cap plates in a column and a taller column with a reflux condenser or dephleg create a high percentage neutral spirit. Copper bubble plates can be taken apart and cleaned with citric acid or mild acid solution.    Sizes Available  4" 99.9% Red Copper bubble plate 6" 99.9% Red Copper bubble plate

    $35.00 - $115.00

  • Sale -38% BVV Brewing 4" Copper Sight Glass Union Tri-Clamp Tee Shop All Categories BVV

    BVV Brewing 4" Copper Sight Glass Union Tri-Clamp Tee

    BVV Brewing  4" Copper Sight Glass Union Tri-Clamp Tee   4" Copper Sight Glass Union Tri-Clamp Tee 4"x 4"x 3",Distillation Lens Column For Home Brewing ,Length 150mm. Specifications Material Red Copper/Stainless Steel Connection method: Clamp Connection Pipe size: 4" Surface treatment Mirror Surface Medium Oil Chemical industry water conservancy electric power boiler, machinery metallurgy sanitary construction etc.

    $200.00$125.00

  • 304 Stainless Steel Ball Bearings Packs 1/8-inch Diameter

    304 Stainless Steel Ball Bearings Packs

    304 Stainless Steel Ball Bearings - Packs 304 Stainless Steel Ball Bearings are a great addition to aiding in filtration because they increase the surface area inside a system and allow fats and lipids to cling to them. After a run is complete, they are easily cleanable. These ball bearings come pre-packaged in 140-gram packets and may have a quantity +/- the stated quantity per pack. Sizes Available: 1/8" Diameter - ~1150 Ball Bearings Per Pack 1/4" Diameter - ~150 Ball Bearings Per Pack 7/16" Diameter - ~25 Ball Bearings Per Pack

    $7.00 - $31.00

Login

Forgot your password?

Don't have an account yet?
Create account