Shop Components
CPS TRS21 Compressor Head Complete Stainless Rebuild Kit
CPS TRS21 Compressor Head Rebuild Stainless Kit Upgrade the compressor head on the TRS21 to be compatible with CBD oils by replacing all the existing O-ring seals with Viton. Replace all brass fittings with Stainless Steel to by inline with FDA on consumable products. Replace springs and valves. Compressor Head Rebuild Instructions
$80.00
Pump Rebuild Kits for 14.1 - 21.2 - 35.3 Pro Series Pumps
Pro Series Vacuum Pump Complete Service Kit This is a complete vacuum pump service kit for the BVV™ Pro Series 14.1, 21.2, 35.3CFM line of vacuum pumps and allows the user to completely rebuild their pump and keep it running like new.
$425.00 - $550.00
1.5" Tri-clamp Thermometer
1.5" Tri-clamp Thermometer High-quality adjustable stainless dial 1.5" Tri-clamp thermometer with back mount orientation. This thermometer is perfect for process temperature monitoring in sanitary applications allowing precise monitoring of temperature. The stainless Dial Thermometer face is 3-inch diameter and reads 0 to 220 degrees in Fahrenheit and 0 to 100 degrees in Celsius. This thermometer is 1.5″ Tri-clamp and the probe depth from the tri-clamp is 2″ long.
$50.00
Female Elbow
SSP - Female Elbow SSP Instrumentation TruFit® is manufactured from fully-traceable raw material to close tolerances and superior surface finishes. TruFit® provides optimal performance when installed in accordance with SSP’s recommendations and the design parameters appropriate for each type of connection – tapered thread, straight thread, and weld & braze. TruFit® components are cleaned in accordance with SSP documented work instructions using equipment calibrated to NIST standards with environmentally-safe and stable agents, ultrasonics, and heat/ temperature to remove all residual oil, grease, and loose particles. Stainless steel components are passivated to the requirements of MIL QQ-P-35 and ASTM A 967. ***Note: ALL NPT Threads REQUIRE the user to properly install the fitting by using a thread sealant to prevent leaks. BVV recommends GAS PTFE Tape Specifications Connection Type 1 Female NPT Connection Size 1 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Working Pressure (PSIG) 1/4" - 7750 3/8" - 6800 NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!
$14.00 - $19.00
12" Collection Base
Pre-Built 12" Collection Base Double your capacity or configure your own custom system with BVV's Pre-Built 12" Collection base. Available in three different variations to suit your application all models of BVV's Pre-Built 12" Collections Base comes standard with high-pressure clamps, borosilicate sight glasses, and full-bore ball valves. Version 1 is the base model equipped with the standard 12" welded base perfect for cost-conscious applications. Version 2 is equipped with a 12"x12" spool & 12" splatter platter to make extract harvesting a breeze, and Version 3 is the top of the line 12" Colleciton base equipped with a 12" jacketed splatter platter for both optimized solvent recovery and ease of harvesting extract. Specifications High Pressure Clamps 2X 2" Borosilicate Sight Glasses 1X 125 PSI ASME Safety Valves 1X -30hg-250PSI Compound Pressure Gauge 1X 1/2" JIC Lid Valve 2X 1/4" JIC Lid Valves Maximum Pressure Rating: 125PSI Variations V1 : 12x12 Base (1200X12B) V2: 12" Splatter Platter base (1200X12S+1200SPL) V3: 12" Jacketed Splatter Platter Base (1200X12S+1200FJS)
$917.00 - $1,291.00
Mastercool Blue 60" HVAC Hose
This HVAC hose will fit 1/4" SAE or JIC fittings. One end of the hose has a fitting made to depress a Schrader valve within the male fitting, the other end of the hose is a standard connection.
$15.00
12" Hemispherical Extractor Lid with 6" Triclamp Center
12" Hemispherical Extractor Lid with 6" Triclamp Center This End Cap comes with Four FNPT Threaded connections, two 2" Tri-Clamp ferrules welded to the end cap, and a 6" Tri-Clamp center port. They allow the user to adapt and connect threaded connections to the NPT ports and Tri-Clamp lid connections to the others. These 7 connections are welded on a 12" Hemispherical Tri-Clamp End Cap. Specifications Material: 304 Stainless Steel Connection Types: 2" Tri-Clamp (2x) 6" Center Tri-Clamp Port 12" Tri-Clamp 1/4" - 18 FNPT (x2) 1/2" - 14 FNPT (x2) Standard: 3A
$300.00
1/4" Fractional Tube Fitting Hose
1/4" Fractional Tube Fitting Hose These chemically resistant PTFE braided hoses are a necessity when dealing with harsh chemicals or solvents and high-pressure applications. They provide a uniquely rugged, durable, and chemically resistant combination of Stainless Steel and PTFE by having an inner core of PTFE and protecting that with a braided stainless steel outer sleeve. These hoses have a tube stub on each end that fits a standard compression fitting. ***Note: Do not exceed the specified hose bend radius or the inner PTFE liner will kink and the hose integrity will become compromised and should not be used. Stainless Steel Hose Technical Data Sheet Specifications: Connection Type(s): 1/4" Tube Stub Liner Material PTFE (Teflon) Braid Material 304 Stainless Steel Swivel Material 304 Stainless Steel Temperature Rating -65°F to 450°F (-54°C - 232°C) Pressure Rating 2100 PSI Chemical Resistance Excellent Max Bend Radius 3"
$48.00 - $70.00
Julabo Adapter 8891609 M16x1 f to NPT 1/2″ f
Julabo Adapter 8891609 M16x1 f to NPT 1/2″ f 2 Adapters M16x1 f. to NPT 1/2″ f.
$233.00
Welch CRVpro Direct Drive Rotary Vane Vacuum Pump CRVpro8
Welch CRVpro Direct Drive Rotary Vane Vacuum Pump CRVpro8 ***Note: This item has a possible 1-2 week lead time depending on stock availability*** Product Details The new CRVpro family of direct drive vacuum pumps offers increased reliability and longer service interval vs. other direct drive rotary vane vacuum pumps. The CRVpro family consumes up to 36% less oil than comparable pumps. Three features drive these benefits: Runs 10°C cooler than comparable pumps. Slows corrosion. Has a 40% larger oil capacity than comparable pumps. Dilutes aggressive chemicals. Has a chemical resistant coating in the oil case and pump module. Protects non-moving parts. The CRVpro family includes all the features you'd expect in a direct drive rotary vane pump: gas ballast, forced oil lubrication, anti-suckback mechanism and thermal overload protection. Suitable applications include freeze drying, degassing, vacuum ovens and concentrators. 3081-01 is wired for North American 115V, 60Hz operation. Includes North American line cord, vacuum inlet hose barb suitable for gum rubber hose from 5/8" to 3/4" ID, and a charge of oil. 3082-01 is wired for North American 230V, 60Hz operation. Includes 230V North American line cord, UK cord, and skuko cord, and a charge of oil. Direct drive pumps are not recommended for filtration, aspiration, drying electrophoresis gels, or other applications requiring sustained operation above 30 torr Specifications Application CRVpro8 Free Air Displacement @ 60 Hz, cfm (L/min) 5.6 (158) Free Air Displacement @ 50 Hz, m³/hr (L/min) 8 (133) Ultimate Pressure, torr (mbar) 5x10⁻⁴ (4x10⁻⁴) Noise Level, dBA 50 Motor Speed, RPM, @60Hz, @50Hz 1740 (1450) Motor Power, HP (kW) 0.4 (0.5) Oil Capacity, mL 1000 Connection Flanges NW 16 Inlet Hose Connection* 5/8" to 3/4" Weight, lbs (kg) 49.6 (22.5) Dimensions, LxWxH, in (mm) 18.2x6.1x9.1 (463x157x230)
$4,150.00
BVV Pro Series Oil Mist Filter/Trap
BVV Pro Series Oil Mist Filter/Trap Pro Series Vacuum Pump Oil Mist Filter allows the user to filter out any oil mist due to the vacuum process and will eliminate your work area from being contaminated with fine oil mist. An oil mist filter also captures the oil and lets it drain back into the vacuum pump after the pump is turned off and making the vacuum pump noticeably quieter during operation. The Oil Mist Filter also has KF25 flange for the 14.1 and 21.2CFM or KF40 flange for the 35.3CFM. A gasket is included with every Pro series pump but standard gaskets and clamps can be purchased separately if needed. These oil mist filters can be used with any vacuum pump with KF25 or KF40connections. We recommend the 14.1 and 21.2CFM for any vacuum pump up to 24CFM. We recommend the 35.3CFM for any vacuum pump up to 40CFM.
$250.00 - $380.00
BVV Thermometer Thermowell
BVV Thermometer Thermowell High quality adjustable stainless dial thermometer that adjusts from straight to a 90 degrees. This thermometer is the one that goes in the top of the still with upgraded thermometer and adjusts to 90 degrees so you can see the temperature at the top of the column. Being adjustable these will also work in the boiler or milk can as well. see photos to see angle of adjustment. Stainless Dial Thermometer face is 3 inch diameter and reads 0 to 300 degrees in Fahrenheit and 0 to 150 degrees in Celsius. Fitting is 1/2″ male threads and these have a 2″ long probe. Calibration screw on the back so if the temperature is off you can adjust it read correctly
$25.00
KF Connection Braided Stainless Steel Bellow Hose
KF Connection Braided Stainless Steel Bellow Hose This KF or (NW) bellow hose is made out of 304-grade stainless steel with braided exterior which allows a high vacuum to be obtained with a large flow diameter for vapors. These bellow hoses are flexible and allow the user to connect a KF flanged vacuum pump to a KF flanged vacuum oven or any other application using adapters. Sizes Available: KF-16 KF-40 KF-50 Lengths Available: 20" 40"
$80.00 - $165.00
KF-25 Stainless Steel 90 Degree Manifold
KF-25 Stainless Steel 90 Degree Manifold This 90 degree stainless steel KF-25 manifold has 2 1/4" FNPT ports and measures 10" x 7".
$65.00
BVV Compression 6" Tri-Clamp x (3) 1.5" TriClamp x (2) 3/8" Compression x 1/4" Compression x 1/2" Compression Hemispherical Lid
BVV Compression 6" Tri-Clamp x (3) 1.5" TriClamp x (2) 3/8" Compression x 1/4" Compression x 1/2" Compression Hemispherical Lid This End Cap comes with (4) Compression connections and Three 1.5" Tri-Clamp ferrules welded to the end cap with a sanitary weld with a 3" Tube Extension Below the Lid. They allow the user to adapt and connect a tube stub connection to the 1/4" port on a Tri-Clamp lid and the 1.5" Tri-Clamp Connection. These 7 connections are welded on a 6" Hemispherical Tri-Clamp End Cap. Specifications Material: 304 Stainless Steel Connection Types: 1.5" Tri-Clamp with 3" Tube Extension Below Lid on Center Tri-Clamp Port 6" Tri-Clamp 1/4" and 1/2" Female Compression Connections Standard: 3A
$195.00
BVV 2 Cylinder Active Closed Loop Recovery Kit ITS/ETL to ANSI/ISA Certified
BVV 2 Cylinder Active Closed Loop Recovery Kit ITS/ETL to ANSI/ISA Certified (Pump comes with 1 yr. limited warranty) This is an Upgrade Kit which can be added to any one of our passive systems making it into an "Active" Closed Loop System. The Active Recovery Upgrade Kit will increase recovery times by condensing the vapor a lot faster than just a hot/cold differential. This will increase efficiency and productivity, many professionals use this method, as this drives profits. This Kit Includes the Following: BVV 2 Cylinder Butane Recovery Pump ITS/ETL to ANSI/ISA Certified BVV Large Condensing Coil 1/2" x 24" SS JIC Braided Hose (2) 1/2" x 48" SS JIC Braided Hose (2) 1/2" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV 5' HVAC Hose BVV Vacuum Tee RECOVER MORE WITH LESS BVV is proud to introduce our new and powerful line-up of Butane & Propane Recovery Pumps. Blending compact design with improved Gen III Pistons from RKMAC, this collection of pumps can help you recover 1lb. of butane every 1:40 Seconds! This pump Assembled in the USA and all the critical parts are domestically made. Finding parts wont be an issue with this pump. The piston seals are rated to 450F and the average operating temperature of the pump is 175F leading to a long service life. Certified by ITS/ETL to ANSI/ISA 12.12.01 for Use in Hazardous locations Class I & II, Division 2 and Class III, Divisions 1 & 2 environments. The computer controlled brushless DC motor operates at 3000 RMP nearly twice as fast as any other pump in its class. BVV Butane/Propane Recovery Pumps are: Process up to 10,000 lbs. of vapor recovery before rebuild Equipped with oil-less reciprocating compressors for a clean product Designed and Assembled in the U.S.A. with domestic and global parts Affordable and highly cost efficient Available in 2-Cylinder, 4-Cylinder, CMEP Retrofit Comes with a 1-year Manufacturer’s Warranty covering Hemp usage Rated universal voltage 100-240V AC 50/60 Hz 1Ph Built with high efficiency Brushless DC Motor used for variable speed control Equipped with Viton O-Ring Seals for Butane/Propane gas and oil compatibility Certified by ITS/ETL to ANSI/ISA 12.12.01 Noise level: 90.3 dB at 1m *Butane recovery results were achieved on a collection base pressure greater than 30psi and using a recovery cylinder with a pressure <10psi. A dry ice coil was used in between the output port of the pump and the recovery cylinder to condense vapor.
$2,500.00 - $2,600.00
1/2" Compression End Cap 1.5" Triclamp
1/2" BVV Compression End Caps These End Caps come with a 1/2" Female Compression connection welded to the end cap with a sanitary weld. They allow the user to adapt and connect a 1/2" male tube stub connection to the lid. Specifications Material 304 Stainless Steel Connection Type: Tri-Clamp 1/2" Female Compression Connection Standard: 3A
$52.00
Edwards nXDS Series Dry Scroll Pumps Tip Seal Service Kit
Edwards nXDS Series Dry Scroll Pumps Tip Seal Service Kit The nXDS series is the next generation in completely oil free, dry scroll pumps nXDS improves on legacy XDS pumps by offering increased pumping speeds, combined with lower ultimate pressures, lower power consumption and lower noise. Gas ballast allows for pumping of condensable vapours including, water, solvents, dilute acids and bases. nXDS pumps also feature the latest in tip seal technology giving significantly longer life between tip seal changes. Integrated inverter drive with auto sensing voltage input delivers optimized pumping performance globally. nXDS pumps are designed to be completely field serviceable. Features: Lubricant-free within the vacuum envelope and hermetically sealed means totally clean and dry vacuum to prevent cross contamination No atmosphere to vacuum shaft seals means bearings are completely isolated, which prevents process attack and means the bearings run cooler and last longer Simple single sided scroll arrangement combined with an innovative motor and bearing design allows for easy field service with a minimum of special tooling for low cost of ownership and maximum up-time Improved motor and drive efficiencies for reduced power and cost of ownership Advanced interface provides a variety of traditional, analogue and digital control methods enabling remote control/monitoring via USB, RS232 or RS485 One year warranty, as well as technical
$585.00
Pressure-Relief Valves for Cryogenic Liquids
Pressure-Relief Valves for Cryogenic Liquids Valve Function Pressure Relief For Use With Liquid Carbon Dioxide, Liquid Nitrogen, Liquid Oxygen Activation Pressure Driven Inlet Pipe Size 1/4 Connection Type Pipe Pipe Connection Type Threaded Connection NPT Male Location Bottom Maximum Pressure 600 psi Relief Port Thread Size 3/4"-20 Connection Type Pipe Pipe Connection Type Threaded Connection UNEF Female Location Top Set Pressure Accuracy ±5% Set Pressure Configuration Nonadjustable Temperature Range -320° to 165° F Shape Straight Overall Height 2 5/8" Material Body Brass Valve Type Relief Flow Coefficient (Cv) Not Rated Specifications Met CGA G-4.1 RoHS RoHS 3 (2015/863/EU) compliant with exemption 6(c) - Lead in copper alloy REACH Not Compliant DFARS Specialty Metals COTS-Exempt Country of Origin United States USMCA Qualifying No Schedule B 848140.0000 ECCN EAR99 Cleaned and bagged to meet CGA G-4.1 for oxygen service and other high purity applications, these valves are built to withstand the extreme cold of liquid carbon dioxide, liquid nitrogen, and liquid oxygen. They begin opening at the set pressure and fully open at about 10% over the set pressure. Valves begin closing as pressure drops and fully close when the system pressure is restored below the set pressure. Set pressure is not adjustable. Valves are not intended for direct contact with cryogenic liquids. Risers (sold separately) are required to convert cryogenic liquids into gases before they contact the valve. 3/8 NPT valve requires a 1/2 NPT × 3/8 NPT bushing when using a riser.
$85.00 - $105.00
ASME 250 PSI Brass Safety Valve - 1/2" MNPT
ASME 250 PSI Brass Safety Valve - 1/2" MNPT Model “SB” ASME safety valve is a high capacity safety valve. Unique O-ring seal ensures valve is bubble-tight to within 10% of set pressure. Set pressure tolerance is +/-3%. SB50 Outline Drawing SB Flow Charts Specifications Construction: Brass Stainless Steel Springs FKM O-Ring Seal Set Pressure 250 PSI Max Temp. 250ºF
$70.00
Male Luer to 1/4 NPT Male Nickle Plated Brass
Male Luer to 1/4 NPT Male, Fitting Material Brass- Nickle Plated.
$20.00
1/2" Clear Reinfornced PVC Tubing
1/2" Clear Reinforced PVC Tubing Crystal clear Phthalate, BPA Free PVC compound, formulated with ingredients in compliance with applicable ratings: NSF-51 Certified USP Class VI Rated Compound, FDA Ingredients, Self-Extinguishing and Reinforced with braided polyester yarn. Key Features: Constructed with Phthalate Free compounds. NSF-51 certified material. Crystal clear - allows visual confirmation of product flow. Longitudinally reinforced to reduce elongation under pressure. Lightweight. Self-extinguishing. Non-marking. Silicone-free. Non-conductive. One-piece lengths. Resistant to chemicals (see chemical-resistance chart). Compound hardness 80A Phthalate Free! Common Applications: Food & beverage. Agriculture Drain Line Hose/Tubing Bundling Industrial Air and Water Hose Light Vacuum Liquid and Powder Transfer Medical and Pharmaceutical Sight Gauge Water Lines
$11.00 - $37.00
Spark Free Safety Tools- 200mm Adjustable Wrench
200mm Adjustable Wrench This adjustable crescent wrench is made of aluminum bronze, a material that will not spark when accidentally knocked against steel and stainless steel materials. This will limit the sources of possible ignition within a solvent rich environment. The jaws on this wrench will fit on a nut or bolt up to 31/32" or 24mm.
$25.00
Pump Part - MVP - 60 PSI, 150 PSI, Liquid, XL150 - Diaphragm Cover Bolts - 8 pack
Pump Part - MVP - 60 PSI, 150 PSI, Liquid, XL150 - Diaphragm Cover Bolts - 8 pack All sales final
$110.00
1/4" Cap
SSP Instrumentation Duolok® tube fittings are designed, manufactured and quality controlled to be totally “interchangeable” with the Swagelok® brand of tube fittings. Component by component examination plainly shows the two brands as completely “componentintermixable.” The precision manufacturing of both products to stringent tolerances under rigid quality control procedures ensures the safety, performance and reliability of service whenever Duolok® and Swagelok® component parts are mixed and used in accordance with published installation and service recommendations. Specifications Connection Type 1 Duolok Tube Fitting Connection Size 1 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Duolok Pressure Rating = Tubing Rating SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA! Dimensions A 0.92 in C 0.70 in D 0.60 in G 9/16 in H 1/2 in T 1/4 in B 0.63 in
$5.00
6" x 1.5" x (2) 1/4" FNPT Tri-clamp Endcap Terpenator Style
This terpenator style endcap goes way back to 2012. With this lid you can use either passive heat and cold techniques for recovery, or a butane pump to reduce cycle time. This lid has tubes installed to direct the flow, and this lid is used for bottom fill extraction techniques. Connections: 1.5" Tri-Clamp (with 6" dip tube) 1/4" NPT (with 6" dip tube) 1/4" NPT
$85.00
KF-50 Stainless Steel FNPT End Cap
KF-50 Stainless Steel FNPT End Cap This is a FNPT KF-50 (NW50) Endcap to adapt a KF50 fitting to Female NPT Threads for 1/4", 3/8", and 1/2" NPT.
$30.00 - $35.00
Scilogex DS-500 Homogenizer Probe
Scilogex DS-500 Homogenizer Probe (Probe ONLY - Motor NOT Included) This is the Scilogex DS-500 Homogenizer probe with either coarse teeth for solid/liquid media or fine slot teeth for Water in Oil/Oil in Water emulsions both probes are good for volumes from 10-5000ml and will attach to the D500 drive motor. Each probe is 20mm in diameter and has a 215mm immerse length with flat head-open slots. DS-500/5 generator 5mm dia. generator, flat head-open slot, 60mm immerse length for solid/liquid media, volumes 1-50ml Slot Type Specifications: Probe Slot Type Specifications Model # Slot Type Media Type DS-500/1 Flat Head-Open COARSE Solid/Liquid DS-500/2 Flat Head-Open FINE Water in Oil/Oil in Water Emulsions DS-500/5 Flat Head-Open slot Solid/Liquid medium,
$804.00 - $924.00
BVV Vacuum Pump Mechanism Rebuild Kits
This rebuild kit is the entire pump mechanism for the BVV vacuum pump. It includes all gaskets and vanes already installed and ready to bolt on the vacuum pump. Select your pump model in the dropdown list.
$35.00 - $64.00
Tri-Clamp Direct Drive Mixers
Tri-Clamp Direct Drive Mixers 3/4 HP Air Direct Drive Tri-Clamp Mixer, (1) 4" PRL, 1" x 28" Exposed, Comp Mech Seal 3/4HP Shaft Length: 28" (From bottom of Tri-clamp) Air inlet port: 1/4" NPT Air adjustment valve to control speed Requires 30CFM @ 100 PSI air supply 3/4 HP Variable Speed Electric Direct Drive Tri-Clamp Mount Mixer 3/4 HP 115V Power supply Shaft Length: 28" (From bottom of Tri-clamp) 1 HP XP Direct Drive Tri-Clamp Mixer, Mech. Seal, (1) 5.5" HEI, 0.625" x 28" Exposed Shaft, VFD Motor: 1 HP, XPFC Inverter Duty, Class 1, Div 1, Group C&D; Class 2,Div 1, Group F&G, Temp Code T4, 10:1 Turndown, 208-230/460V,3Ph, 1760 RPM VFD Controler: 1HP Speed Controller with Digital RPM Readout in Outdoor Rated NEMA 4X Enclosure, 240V/1Ph (Mounted Outside of XP Area)w/ Local XP Control Package, 352 to 1760 RPM, Mounted to Motor ,Bare Wire Leads Mount: 3'' Sanitary Mount, 316SS Wetted faces Seal: 316 SS 60 Series 2-Piece Mechanical Inside Seal w/Viton ORings; Carbon-Graphite Rotary, Sintered Silicon Carbide Stationary, Hastelloy C-276 Springs, Dry Running, Sealed for Pressure/Vacuum Wetted Surface Finish: Mill Shaft: 0.625'' x 28'' Exposed Length, 316SS Bottom Impeller: 5.5'' High Efficiency Impeller, 3 Blades, Low Shear,316SS **On Site Wiring Required**
$4,200.00 - $7,400.00
2" Plastic Drum Faucet
Recommended for dispensing light oils, acids and cleaning solutions. FDA approved high-density polyethylene (HDPE) plastic faucet. The faucet is designed to fit 2" NPT threads and can be used to dispense most non-flammable liquids. Use with plastic and steel drums. Tough polyethylene. FDA compliant. Material: High density polyethylene (HDPE ) is the most commonly used resin. This economical plastic has good impact resistant, is naturally translucent, flexible, and typically used for personal care products, such as shampoo bottles. Adding color will give HDPE an opaque look that will result in an increase in weight and rigidness. We have a variety of these rigid and tough high density polyethylene products in stock, from containers, pails, bottles, caps, tubs, and jugs. HDPE works well in below freezing temperatures. HDPE heat compatibility varies. Generally, it should not be used with products filled at over 145°F.
$25.00
Welch 2062/2064/2067 8 Head Diaphragm Replacement Kit
Welch 2062/2064/2067 8 Head Diaphragm Replacement Kit Service kit for 2064/2067/2062/2163 (8-head)
$1,160.00
Viton Replacement O-ring for TRS21 and BVV 2/4CYL Suction Valves
Viton Replacement O-rings for TRS21 and BVV 2/4CYL Suction Valves sold as single O-ring.
$2.00
TRS21 Valve Head Complete Viton O-ring Kit
Replacement kit with Viton O-rings for the TRS21 head. Compatible for use with the Oil Extraction Market, Butane and Propane Extraction solvents.
$25.00
Pump Part - MVP - 60 PSI, 150 PSI, Liquid, XL150 - CO2 Regulator
Pump Part - MVP - 60 PSI, 150 PSI, Liquid, XL150 - CO2 Regulator All sales final
$440.00
Pump Part - MVP - 60 PSI & Liquid - Shaft Assembly Kit
Pump Part - MVP - 60 PSI & Liquid - Shaft Assembly Kit All sales final
$1,400.00
KPR Fitting Port Reducer
KPR Fitting Port Reducer The KPR Fitting Port Reducer is made out of 316 stainless steel and reduces the port from 1/2"FJIC to a 1/4" MJIC. The connection type is a 37° JIC with a 7/16-20 UNF rated thread. BVV™ KPR Fitting Port Reducer - Data Sheet
$18.00
KF-25 Stainless Steel 90 Degree Manifold - Long
KF-25 Stainless Steel 90 Degree Manifold - Long This 90 degree stainless steel KF-25 manifold has 2 1/4" FNPT ports and measures 10" x 36".
$80.00
4" x 24" Dry Ice Heat Exchanger
This 304 stainless steel heat exchanger is used as a condenser for your extractor setup. It has a sleeve around the heat exchanging tubes and a wide opening at the top to allow users to pour in dry ice to super chill the exchanger. For best results, use dry ice mixed with ethanol to get the most possible contact across the surface area of the tubes. The bottom of the sleeve has a 1/4" NPT drain plug that can be removed to drain ethanol. Connection flanges on top and bottom are 4" Tri-Clamp. We offer a pre built stand alone version that comes with hemispherical caps and JIC connections, but we will be happy to help you configure it any way that you want!
$1,250.00
Safety Tools - The Extractor's Kit (AlCu)
The Extractor’s Safety Tool Kit These tools are forged out of 100% Aluminum Bronze (GB EX IIB). The material hardness is 20-30 HRC, which is still very durable for normal day to day work. They will not generate a spark when knocked against or dropped on steel parts. We have optimized the kit to only include what you will need on our equipment. This kit includes: -Combination Wrenches: 5/8” ¾” -Double End Wrenches: 19/17 mm 17/14 mm 14/10 mm -200mm Adjustable Wrench -250mm Adjustable Wrench -3/8” Drive Socket Wrench -Sockets: ½ 14mm 5/8 11/16 ¾ -Allen Keys: 3/16 ¼ -Phillips #2 Screwdriver-6mm Flathead Screwdriver-500g Cross-Peen Hammer
$500.00
12" x 12" Hemi Lid with Coil V2
12" x 12" Hemi Lid with Coil V2 This 12" Hemi Lid has a built in coil that can be used with a heated circulator to assist with internal temperature control during the recovery process. This hemi lid must be used with our 1200X12S and 1200FJS for proper fitment. PDF DRAWING
$475.00
Distribution Plate - 6"
Distribution Plate - 6" The 6" distribution plate is designed to be placed above a tube in shell heat exchanger to help evenly distribute liquid around the heat exchanger. It has a borosilicate sight glass to give you a visual of flow and dispersion into the heat exchanger.
$500.00
BVV 4 Cylinder Active Closed Loop Recovery Kit
BVV 4 Cylinder Active Closed Loop Recovery Kit (Pump comes with 1 yr. limited warranty) This is an Upgrade Kit which can be added to any one of our passive systems making it into an "Active" Closed Loop System. The Active Recovery Upgrade Kit will increase recovery times by condensing the vapor a lot faster than just a hot/cold differential. This will increase efficiency and productivity, many professionals use this method, as this drives profits. This Kit Includes the Following: BVV 4 Cylinder Butane Recovery Pump ITS/ETL to ANSI/ISA Certified BVV Large Condensing Coil 1/2" x 24" SS JIC Braided Hose (2) 1/2" x 48" SS JIC Braided Hose (2) 1/2" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV 5' HVAC Hose BVV Vacuum Tee RECOVER MORE WITH LESS BVV is proud to introduce our new and powerful line-up of Butane & Propane Recovery Pumps. Blending compact design with improved Gen III Pistons from RKMAC, this collection of pumps can help you recover 1lb. Butane / 0:51 Seconds! This pump Assembled in the USA and all the critical parts are domestically made. Finding parts wont be an issue with this pump. The piston seals are rated to 450F and the average operating temperature of the pump is 175F leading to a long service life. Certified by ITS/ETL to ANSI/ISA 12.12.01 for Use in Hazardous locations Class I & II, Division 2 and Class III, Divisions 1 & 2 environments. The computer controlled brushless DC motor operates at 3000 RMP nearly twice as fast as any other pump in its class. BVV Butane/Propane Recovery Pumps are: Process up to 10,000 lbs. of vapor recovery before rebuild Equipped with oil-less reciprocating compressors for a clean product Designed and Assembled in the U.S.A. with domestic and global parts Affordable and highly cost efficient Available in 2-Cylinder, 4-Cylinder, CMEP Retrofit Comes with a 1-year Manufacturer’s Warranty covering Hemp usage Rated universal voltage 100-240V AC 50/60 Hz 1Ph Built with high efficiency Brushless DC Motor used for variable speed control Equipped with Viton O-Ring Seals for Butane/Propane gas and oil compatibility Certified by ITS/ETL to ANSI/ISA 12.12.01 Noise level: 93.0 dB @ 1m *Butane recovery results were achieved on a collection base pressure greater than 30psi and using a recovery cylinder with a pressure <10psi. A dry ice coil was used in between the output port of the pump and the recovery cylinder to condense vapor.
$2,500.00
Williams Double Open End Chrome Wrench Set
Williams Double Open End Chrome Wrench Set Williams Double Open End Chrome Wrench Set is made in the USA and the two openings in each wrench with 45° chamfer on wrench ends allow easy placement of wrench on the fastener. Continuous arc design minimizes spreading and is stronger than V design. Satin provides good grip and cleans easily. This Kit Includes the following wrench sizes: 9/16" x 5/8" Double Open End Chrome 5/8" x 11/16" Double Open End Chrome 5/8 x 3/4" Double Open End Chrome
$40.00
Boss Head - Double Swivel
Boss Head - Double Swivel Made of high strength powder coated alloy and can support up to 16mm rods. The boss head can be adjusted and locked to any angle (360°). It is also designed to carry heavy loads and prevent torque damage. Furthermore, it has three wide pad metal screws to easily secure itself to a clamp and support apparatus. Note:Clamps and rods are NOT included.
$10.00
Welch ChemStar 1400N 0.9 cfm 0.1 Micron Belt Drive 2-Stage Pump
Welch ChemStar 1400N 0.9 cfm 0.1 Micron Belt Drive 2-Stage Pump ***Note: This item has a possible 1-2 week lead time depending on stock availability.*** Product Details Low rotation speed for longer service life Vital parts corrosion resistant Large oil reservoir dilutes contaminants ChemStar belt-driven Vacuum Pump is designed to tolerate harsh chemical contamination. Vital pump parts are corrosion resistant. The large oil reservoir with PTFE surfaces dilutes contamination and the low pump rotational speed lessens friction to reduce operating temperature and chemical effects. PTFE surfaces, fluorcarbon gaskets and seals, Nitrogen purge to cool and degas oil. ChemStar system comes with Gold Oil, a synthetic lubricant designed to minimize effects of chemical contaminants. Specifications Model Number 1400N Application Vacuum Manifolds, (Schlenk Lines), High boiling point evaporations (to 195 deg. C), General laboratory. HCl, O3, H2SO4*HBr, HOAC, SOx*Br2, F3CCO2H, H2S*Cl2, CH2O, HNO3*SF6, CF4 Fragments and other gases; Type Belt-Drive Vacuum Pump, chemical resistant Free Air Displacement cfm (l/min.) @60Hz 0.9(25) Ultimate Pressure 1 x10-4(0.00013) Pump RPM 580 Oil Capacity 0.62(0.59) Motor Horsepower (watts) 1/3(250) Adjustable Vac. / Gas Ballast Yes Tubing Needed 7/16(11) ISO Exhaust / Intake Flange NW 16 Overall Dimensions LxWxH in. (cm) 17.8x9x12.6 (45.2x22.9x32) Ship Weight 71(32.3) Shipping Carton Dimensions LxWxH in. (cm) 20.5x13.8x14.5 (52.1x35.1x36.8)
$3,425.00 - $4,350.00
Welch ProBoost Air-Cooled Diffusion Pump
Welch ProBoost Air-Cooled Diffusion Pump Product Details Use Welch ProBoost in conjunction with a backing pump like the CRVpro to get deeper vacuum and higher flow. High Vacuum to 10⁻⁵ torr Use with high vacuum and Schlenk lines Employs air cooled diffusion pump Easy Attachment to backing pump Welch ProBoost is an air cooled gas jet pump (commonly called a diffusion pump). The gas jet is formed by directing boiling silicone vapors through a hollow cone. There are no internal moving parts. The pumping action commences when the vacuum pressure in the still (i.e. wiped film) goes below 0.2 torr (200 millitorr). On an empty, leak free still, ProBoost backed by a rotary vane pump lowers the vacuum pressure to 0.00002 torr (20x lower in pressure than a 2-stage rotary vane vacuum pump can do alone). ProBoost backed by a rotary vane vacuum pump will lower vacuum pressure to below 0.0001 torr in high vacuum and Schlenk lines. This high vacuum is invaluable to improve the results from reactions using air-sensitive compounds such as organometallics, metal amides, and hydrides. ProBoost has a built-in control board for fan and heater. When you turn on ProBoost, the fan and heater both turn on. When you turn off ProBoost, the heater turns off immediately and the fan runs for another 20 minutes to cool the pump. Specifications Maximum Pumping Speed, Air 80 l/sec Ultimate Vacuum Pressure 0.00002 torr Minimum Back Pump FAD at 60 Hz 2.8 CFM Maximum Discharge Pressure 0.2 torr Ambient Environmental Temp 10–30°C Heat-up time 7 minutes Inlet Connection NW50 Discharge Connection NW25 Silicone Oil Capacity Approximately 30 ml Cool Down Time 20 minutes Pump Dimensions, L x W x H 5.5 x 5.4 x 7.5 in Weight 5.6 lbs (2.5 kg) Download Manual
$3,850.00
Adapter from VE filters to BVV/CPS pumps
This adapter will fit the exhaust ports on BVV VRD series vacuum pumps and adapt them to fit our BVV carbon exhaust filter.
$15.00
You have seen 624 out of 814 products