Shop BVV
12" Vacuum Chamber Digital Heat Pad
12" Vacuum Chamber Digital Heat Pad Please Read Before You Buy! Chamber NOT Included, Sold Separately. Heat Pad must fit correct size of the chamber! Fits a 5 Gallon Chamber This Digital Heat Pad will adhere to the bottom of a chamber vessel with a peel and stick backing. This unit will hold a temperature within a degree to the set temperature (dependent on the environment and air movement). The temperature offset must be found to set the controller accurately. (See ‘Operation’ instructions in the operation manual) Included with this Digital Heat Pad: Instructions on how to operate and set parameters. Simple standoff bumpers (provide thermal separation between the vessel and the work surface) Thermal tape (best method to check and verify temperature) Specs: UL Listed Fahrenheit Digital Controller. Min Temp: Ambient + 5 Max Set Temp: 160°F Ultimate Max Temp: 248°F Voltage: 110VAC Only Power Consumption: 234-watt Digital Control: Increments of 1 Degree. Accuracy: +/- 0.2 Degrees Units: Degrees Fahrenheit Instructions: Fully included Relay Lifespan: Approx. 10 million cycles User can reprogram: Yes
$135.00
BVV™ Filtration Media CRC Starter Bundle
BVV™ Filtration Media CRC Starter Bundle This is the BVV recommended starter bundle for anyone venturing in to closed loop Color Remediation and desiring to make a clear and cleaner end product. This bundle works well with any of our Inline CRC hardware kits. (Seen here: ICRC300) BVV recommends a Pressure Flow through this bundle @ 30PSI. What's Included in the Bundle? BVV™ Silica Gel 60A - BVV™ Chromatographic Silica Gel is as premium as it gets. We recommend this for our Top layer of the CRC to grab fats, waxes and color bodies. It wont take the place of full dewaxing but it does a darn good job on its own. We recommend 30-50g of Silica per lb. biomass as the top layer of your filtration stack depending on the age of your material and the diameter of your filtration column. Pure-Flo® B80 Natural Bentonite for Bleaching - Pure-Flo® B80 will remove chlorophyll, color bodies, fats, waxes. Its natural neutral pH will help retain terpene flavonoids and clarify and remove dark colors from your oils. B80 is the most commonly used CRC media in extraction. We recommend you use 100g of bentonite Clay per lb. biomass above a layer of Activated Alumina. BVV™ Activated Alumina - BVV™ Activated Alumina is granular media excellent for grabbing water and waxes. We recommend Activated Alumina as the bottom layer of your filtration stack to absorb moisture at 30-50g per lb. biomass depending on the diameter of your filtration column.
$74.00 - $161.00
37 Degree MJIC x FJIC
BVV™ MJIC x FJIC This unique 304 stainless steel fitting allows the user to adapt a 1/4" 37 Degree MJIC to a 3/8" 37 Degree MJIC or vise versa without having to replace or back out the fitting or taping the fitting. BVV™ MJIC x FJIC - Data Sheet Specifications Material 304 Stainless Steel Connection Type(s): 1/4" 37° FJIC X 3/8" 37° MJIC 3/8" 37° FJIC X 1/4" 37° MJIC
$6.00 - $7.00
1.5" Open Blast Extractors 45-270g
1.5" Open Blast Extractors 45-270 Gram Capacity Open Blast Extraction is an economical method which allows for instant extraction of plant material. These columns are designed with ease of use in mind. These extractors come with a Material Tube, 1x Mesh Buna Gasket, 1 Regular Buna Gasket, Quadpod, Clamp, Ferrule, 8" x 8" Silicone Pad, and an Open Blast Top Cap. All Stainless Steel components are made out of 304 Grade Stainless Steel. Optional Upgrade(s) and Addons: Showerhead Upgrade: Allows the solvent to be spread more evenly through the plant material inside the column. What's Included?: 1.5" Solid Endcap with 3mm Hole Standard Pressure Clamp Material Tube (User Can Upgrade Capacity Through Dropdown Options) 1.5" Tri-Clamp Quadpod 1.5" Ferrule 8" x 8" Silicone Pad 1.5" Buna N 100 Mesh Gasket (150 Micron) 1.5" Buna-N Gasket *Note: Column capacity may vary depending on the density of packed material and packing density. Capacity is calculated using the industry standard of 4.2g/in3. This is the upper limit for column capacity. Low density, uncut, and/or lightly packed material can reduce capacity by 50%. For best results, we recommend to tightly pack coarse ground material. Material Capacity Cylinder Volume Radius (in) 1.5" 2" 3" 4" 6" 8" 10" 12" Length (in) Volume (in3) Select Material Butane ISO-Butane Propane How Much Will Fit in Cylinder FormulaVolume x Weight of Water x Specific Gravity ConstantsWeight of Water = 0.0360 (lbs / in3)Specific Gravity of = Lbs. of : Recommended: Account for an 80% fill to avoid a hydraulic lock How Much Material Will Fit in the Cylinder Volume Packing Density (g) 2.5 3 3.5 4.3 Grams of Material Lbs. of Material Cans of Butane Cans of Butane by Size Pounds of Butane mL fl oz lbs # of Cans 420 14.2 300 10.1 200 6.7 150 5.07
$70.00 - $100.00
Glass Vac 5 Gallon Aluminum Vacuum Chamber
5 Gallon Vacuum Chamber (Comes with 2 year Limited Warranty) This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Utility Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. Glass Vac Vacuum Chambers are ideal for wood workers using the wood stabilization process because the glass lid will not deteriorate like acrylic or polycarbonate lids. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: Aluminum Vessel Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum. Specifications Chamber Material 3004 Aluminum Gasket Material Silicone Lid Material Glass Internal Dimensions (ID) 10" Tall x 12" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC Hose Platinum Cured Silicone Pad Black 50 Micron Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings. Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Exludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min. For shipping info including Import/Export details visit our Shipping link at the bottom of the page.
$233.00
MOLYKOTE® High Vacuum Grease 150g
Key Properties: NLGI Grade 3-4, translucent white, used primarily in sealing vacuum and pressure systems. Molykote Technical Data Sheet Molykote Safety Data Sheet Applications: Seals and lubricates chemical processing equipment. Lubricating plug valves, control valves, flow meter bearings, ceramic plug cocks, fire extinguisher valves, water treating equipment, synthetic rubber gaskets and seals in high-temperature applications. Sealing vacuum and pressure systems. Lubricating O-rings in binoculars and telescopes; prevents fogging of delicate lenses. Performance Benefits: Reduces wear in plastic-to-metal and rubber-to-metal contact Low volatility Excellent resistance to water, chemicals, and high and low temperatures Meets requirements of FDA 21 CFR 175.300 Good chemical resistance Good oxidation resistance Good plastic & rubber compatibility Good water resistance High tack & adhesion High temperature performance Low temperature performance Wide temperature range Product Details: Product type: Compounds Technology: Silicone NLGI Grade: 3-4 Thickener: Silica Low Temp: (C) -40 High Temp: (C) 204 Color Translucent: White
$46.00
1.9CF ECO Vacuum Oven - 4 Wall Heating, LED display, LED's - 6 Shelves Standard
DISCLAIMER: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in WELL VENTILATED AREAS! 1.9CF ECO Vacuum Oven - LED - 6 Shelves Standard Backed with our 2 Year Parts and Labor warranty The 1.9CF Vacuum Oven Shelf offers guaranteed industry-standard ability to lose less than 1” Hg over a 24 hour period. Our reliable deep vacuum also reaches below 0.1 torr. with stainless steel compression-fit tubing and stainless steel instrumentation valves. Best of all, this device performs uniform heat, which is essential to an effective oven. Our ovens offer 7% temperature uniformity across all shelves with offering ±1⁰ stability in temperature and comes with the maximum number of shelves as well as a well-lit LED interior. Items Included: 5' 37⁰ female flared HVAC hose; USA power cord; and oven operation manual. You’ll get the complete package only with BVV. Our ovens offer: The guaranteed industry standards ability to lose less than 1” Hg over a 24 hour period. Reliable deep vacuum that reaches below 0.1 torr. with stainless steel compression-fit tubing and stainless steel instrumentation valves. Uniform heat which is key to an effective oven. Our ovens offer 7% temperature uniformity across all shelves with offering ±1⁰ stability in temperature. Comes standard with the maximum number of shelves and a well-lit LED interior. Key Oven Features: 1/4" JIC Vacuum Port with included 5' HVAC Hose Easy Vac-Release Dial allows release of vacuum without disconnecting pump or purge Stainless steel interior for a sanitary, easy-to-clean look Overload circuit breaker for electrical protection Comes standard with 4 (0.9CF Eco models) or 6 shelves (1.9CF Eco models) Specifications Electrical 120 VAC / 60Hz / 800W / USA Plug Internal Chamber Material: Polished Stainless Steel Dimensions (LxWxH): 14.25" x 16.5" x 13.75" Temperature Control Four Wall Heating LED PID Controller Temperature Range: RT+18F - 212F Temperature Stability: +/- 1.8F or 1C Automatic Over Shoot Shut Down Over Temp Alarm Vacuum Gauge Ranging From -1inHg to -30inHg Maximum Vacuum Level -29.9inHg / 75.4 cmHg / -1 MPa Shelves Up to 11 Removeable Shelves Shelf Capacity(Area): 129in^2 Total Shelf Capacity: 1035 in^2 or 7.2ft^2 Dimensions (LxW): 11-3/8" x 11-3/16" Door 1/2" Tempered Glass Window Integrated LED's Replaceable Gasket Material: Silicone Window Dimensions: (LxH): 11.75" x 11" Weight & Dimensions Outside Dimensions (LxWxH): 28" x 22" x 21.5 Weight: 205lbs Compliance CE Listing Recognized ISO 9001:2008 ISO 13485" 2003 Manufactured in Acc. w/ Q/TIWY7-2004 IEC68-2-3 Note: This oven does NOT contain a vacuum pump. External pump is required to achieve vacuum pressure. Note: This item is a freight ship item and will ship Via UPS Ground Freight. Expedited freight can only be calculated by calling customer service 331-281-0154. All orders with expedited freight through the website will not be honored and will need to be re-quoted. A valid Phone Number IS REQUIRED to ship, Otherwise UPS freight Cannot Contact you for a delivery setup window. Freight Time is 2-5 Days. West Coast 5 Days, Midwest 2 days, East Coast 3-4 days.
$1,550.00 - $1,650.00
Tri-Clamp Build-A-Lid with BVV 316SS Full Bore Valves
Tri-Clamp/ Tri Clover Build-A-Lid This is the BVV™ Build-A-Lid for standard tri-clamp end caps in which customers are able to make their own lid configuration to suit their needs. The standard lid come with 1/4" 37 Degree Flare and BVV 316SS Full Bore Valves. These lids are pre-assembled and nitrogen tested for leaks at the BVV™ Warehouse to ensure the customer of a leak-free extraction part. Standard Lid Specifications: BVV 316SS Full Bore Valves 1/4" FNPT 316 Stainless Steel Instrumentation Ball Valve -40F to 450F 1/4" 37 Degree JIC 304SS Flare 1/4" Pipe Nipple 304 Stainless Steel End Cap (Size Picked by Customer) Upgrade Specifications: Compound Gauge - 1/4" MNPT Compound Gauge (-30)-0-(150PSI) Sight Glass - 1/4" FNPT Stainless Steel Sight Glass
$58.00 - $182.00
Inland 19 Vacuum Pump Oil
Inland 19 Vacuum Pump Oil Inland 19 is Inland Vacuum’s recommended general-purpose hydrocarbon fluid for mechanical vacuum pumps used in non-corrosive applications. The manufacturing process of Inland 19 includes molecular distillation, which removes light end fractions present in the fluid and gives it the desired properties: lower vapor pressures, reduced backstreaming, and longer fluid life. As a result, it can be used within the same applications as more expensive diffusion pump oils which would otherwise be contaminated by a vacuum oil of lower grade.A durable, long-lasting mechanical pump fluid, Inland 19 is cost-effective in vacuum applications such as mass spectrometers, electron microscopes, thin-film sputtering, UHV systems, and freeze dry systems. Proper use of this oil effects reduced maintenance costs, improved pumping cycles, and a cleaner vacuum system. Inland 19 MSDS Properties: Molecularly distilled Reduced backstreaming Increased fluid life Low vapor pressure Areas of Application: Mass spectrometry Electron microscopy Thin film sputtering UHV systems Freeze dry systems Other non-corrosive general applications Specifications Inland 19 Vapor Pressure at 25ºC (torr) 1x10-5 Boiling Point at .01 torr (ºC) 112 Viscosity at 40ºC (cSt) 55 Pour Point (ºC) -15 Flash Point (ºC) 213 Fire Point (ºC) 244 Density at 25ºC (g/ml) 0.87
$24.00 - $1,275.00
Female Tee
BVV™ Female Tee BVV™ brand stainless steel parts are made with precision 304 Grade Stainless Steel and are clean and free from burrs or debris. These fittings are NPT threads (National Pipe Taper) and will compress against other Female/Male NPT threads creating a tighter and tighter connection. All NPT threads require thread sealant to create a watertight and gas-tight seal between the threads. We recommend using Yellow Gas PTFE Tape because it is rated for gases and is UL listed and it is NOT recommended to use white PTFE tape because it is not rated for gas service. Stainless Steel Female Tees are used to connect 3 Male NPT threaded connections together for either diverting flow in a system or even isolating a section of the extraction system. BVV™ Female Tee - Data Sheet Specifications Material 304 Stainless Steel Connection Type(s): 1/4"-18 FNPT 3/8"-18 FNPT Sizes Available: 1/4" 3/8"
$20.00 - $40.00
Glycerine Filled Vacuum Gauge Custom, for our Chamber Lids Only
Glycerine Filled Vacuum Gauge Custom has a stainless steel housing and brass fittings for ultra-durablility and designed exclusively for our premium Chamber Lids. 5/16-18 Threaded Stem includes washer, nut and gasket.
$28.00
Compact In-line Sight Glass Female NPT Stainless Steel (Flow Sight)
The body of the flow sight is 304 stainless steel. The glass sight has a pressure tight, solid gasket design with Viton seals. The unit tolerates temperatures up to 180° F. The maximum recommended pressure is 125 PSI. BVV™ FNPT Stainless Steel Sight Glass - Data Sheet Specifications 1/4" 3/8" 1/2" 1" Body Material 304 Stainless Steel Gasket Material Viton Length 2-3/16" 2-1/4" 2-1/2" 2-7/8" Width 7/8" 1" 1-1/4" 2" Viewing Port Size 1" 1-1/8" 1-3/16" 1-1/4" PSI Rating 150 150 100 100
$74.00 - $105.00
1.9CF BVV™ Neocision ETL Lab Certified Vacuum Oven
1.9CF BVV™ Neocision Certified Lab Vacuum Oven - 5 Wall Heating, LED's, 11 Shelves Standard - 3 Year Warranty Disclaimer This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in well-ventilated areas! Backed by our 3 Year Parts and Labor Warranty. Introduction Our vacuum ovens are purpose-built to perform degassing / purging of light hydrocarbon solvents. Using the technique of cold boiling, the oven applies a gentle heat under reduced pressure conditions to expedite solvent degassing while simultaneously preserving color, aroma, and overall solute quality. We've applied our extensive vacuum expertise and industry experience to produce a series of ovens designed exactly for your needs: low consumption, high-throughput, and reliable operation. Performance Capabilities At BVV™, we make every effort to provide oven performance capabilities in a standardized format. We're not interested in juking our stats to make a sale. Instead, our goal is to provide quality, transparent production capabilities that meet the demands of our professional customers. Temperature Stability: ±1.0° Temperature Range: Room Temp+18°F to 212°F Temperature Uniformity: within 5% of the temperature setpoint. Heat-Up Time: 45 minutes to preheat. Optimal saturation reached in 120 minutes, over 30 minutes faster than competitors. Ultimate Vacuum: <500 µmHg / mTorr / micron Time to Vacuum: 4 minutes to 29"Hg using our VE Series 4cfm Dual Stage Vacuum Pump. Vacuum Hold: guaranteed to lose less than 1"Hg (25.4 torr) in 24 hours. Technical Data Electrical Voltage 120V Frequency 60Hz Power 650W Current 10A Plug IEC C13 (unit ships with detachable NEMA 5-15p cable) Internal Chamber Heating Superior 5 Wall Heating (left, right, top, bottom, rear) Chamber Material Stainless Steel Dimensions (LxWxH) 14.5" x 16" x 13.5" Vacuum Gauge Style Glycerin-filled for accuracy and longevity Range (units) -30 to 0 (inHg) / -1 to 0 (bar) Shelving Ships With 11 Slide-in Shelves Shelf Dimensions (LxW) 13" x 15" Shelf Capacity 195 in2 Total Shelf Capacity 2145 in2 / 14.9 ft2 Safety Seal Silicone on Tempered Glass Window Dimensions (LxH) 15.25" x 12.75" Lights 4 strips of LEDs provide clear, bright view of the interior Handle No plastic, all metal parts for lifetime durability Exterior Dimensions (LxWxH) 28.5" x 23" x 22" Weight 160 lbs Support Heavy Duty Casters and Adjustable Leveling Feet Safety Electrical Built-in, resettable, overcurrent circuit breaker Thermal Automatic overtemperature shutoff Compliance CE CE Listing Recognized ISO ISO 9001:2015 ETL Certified Conforms to ANSI/UL STD.61010-1, 61010-2-010 -- Certified to CAN/CSA STD. C22.2 NO.61010-1, 61010-2-010 Connections Vacuum Inlet KF25 / NW25, quarter-turn valve Purge Inlet 5/16" Barbed, 10-turn valve Atmospheric Release Quick-release dial Contains Ships With KF25 x 1/4" JIC Flare with 1/4" vacuum hose and adjusting wrenches. User Manual Included Vacuum Pump Sold Separately. Recommended Pump VE Series 4cfm Dual Stage Vacuum Pump Warranty 3 Years Capacity and Throughput Planning Oven capacity requirements vary widely by the producer. We wanted to create a method to assist in determining the best oven match for your operation, based on a few of the parameters of your extraction and of your desired purge. We based this formula on an expected extraction yield of 25%, with an extract-density of 1 g/in2. Using the following variables, this formula is designed to provide an estimate of your required shelving capacity: Size = Extraction Batch Size (lbs) Number = Runs per 24h Period Purge = Your desired purging duration (hours) Area Required (ft2) = [(Size) * (Number) * (Purge+1)] / 122 Area Required (in2) = (Size) * (Number) * (Purge+1) * 1.18 *Candy Drying with a BVV Vacuum Oven Recipe Guide Note: This item is a freight ship item and will ship Via Ground Freight. Expedited freight can only be calculated by calling customer service 331-281-0154. All orders with expedited freight through the website will not be honored and will need to be re-quoted. A valid Phone Number IS REQUIRED to ship, Otherwise Ground Freight Cannot Contact you for a delivery setup window. Freight Time is 2-5 Days. West Coast 5 Days, Midwest 2 days, East Coast 3-4 days.
$1,990.00
Best Value Vacs 2 Gallon Aluminum Vacuum Chamber
2 Gallon Vacuum & Degassing Chamber (Comes with 2 yr Limited Warranty) This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: Aluminum Vessel Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum. Specification Chamber Material 3004 Aluminum Gasket Material Silicone Lid Material Acrylic Internal Dimensions (ID) 6.5" Tall x 10" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC Hose Platinum Cured Silicone Pad Black 50 Micron Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings. Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Exludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min. For shipping info including Import/Export details visit our Shipping link at the bottom of the page.
$108.00
BVV™ MagSil-PR® Adsorbent for Chromatography
BVV™ MagSil-PR® Adsorbent for Chromatography BVV™ MagSil-PR® Adsorbent for Chromatography is an adsorbent for the separation of lipids and is a commercially prepared magnesia-silica gel. MagSil-PR® has a coarse mesh size which helps with rapid flow rate for column chromatography. It's main benefit is pesticide removal from extracted plant material and will dramatically improve the color and clarity of the material. It also has the provided benefit to bind to polar water-soluble compounds which can be filtered out through a 20-micron mesh screen. Particle Mesh Size: 60/100 BVV™ MagSil-PR® SDS
$148.00 - $1,875.00
Glycerin Filled Compound Gauge with 1/4" NPT Back Mount - (-30)-0-250 PSI.
Glycerin Filled Compound Gauge with 1/4" NPT Back Mount BVV™ Glycerin filled compound gauge has a 1/4" MNPT stainless steel connection with a readout of (-30) -250 PSI. BVV™ Compound Gauge - TDS
$26.00
Stainless Steel (316) Ball Valve - 1 Piece Standard Port, 1,000 PSI (WOG)
DuraChoice 316 Stainless Steel Ball Valve - 1000WOG Stainless Steel (316) Ball The standard port VBS01 line is ready for action, with a 1000 psi rating, pure Teflon seats and seals, and a locking handle for added safety. Works with a wide variety of liquids and gasses. - 1pc Standard Port, 1,000 psi (WOG)SS316 Investment casting bodyWorking Pressure 1000 psi (WOG)Pure teflon seals and seatsSuitable for full range of liquids and gasTemperature range: -60 to 450 degree FahrenheitLow operation torque100% individually testedBlowout-proof stemFxF NPT Threaded ends to ANSI B1.20.1Heavy duty locking handles with blue vinyl insulatorDescription - MaterialBody - SS316 (CF8M)Ball - SS316 (CF8M)Cap - SS316 (CF8M)Ball Seat - RPTFEThrust Washer - PTFEStem Packing - PTFEStem - SS 304Packing Ring - SS 304Spring Washer - SS 304Stem Nut - SS 304Handle - SS 304Handle Lock - SS 304Handle Cover - PlasticPlease Note: Brass components in this product contain lead, known to the State of California to cause cancer and birth defects or other reproductive harm. California law requires that this warning be given to consumers.
$27.00 - $30.00
Alumilite Dye
Use Alumilite’s Dyes to color your casting resin. Can be used in the water clear resin to make a translucent colored casting. The dyes are added to the “A” side by weight up to 5%. Use the Flesh tones according to your preference of shade (flesh tones are typically used in Alumilite White to achieve the best results). NOTE: 1 oz. bottle dispensing tip must be cut to dispense dye. Tip may also be removed completely. Disclaimer: Bottle style/label may vary from what is pictured due to mfr. labeling update. Otherwise it is still the same product.
$6.99
Pure-Flo® Perform 6000 Highly Activated Bleaching & Decolorizing Bentonite for Edible Oils *FDA-GRAS
Highly Activated Bentonite Clay for Bleaching & Decolorizing Edible Oils pH: 2.5 Pure-Flo® Perform 6000 is a highly activated bentonite clay that is used to purify extremely difficult to bleach oils with the most challenging levels of chlorophyll and color bodies. Particle Size: 325 Mesh Color: Beige Performance Features & Benefits: Filter Aid Removes phosolipids Excellent Metal adsorption (P, Ca, Fe, Mg, etc.) Effective with all types of difficult-to-bleach oil Top chlorophyll removal in its class & improved red color reduction pH 2.5 FDA GRAS (Generally Recognized as Safe) - This product is safe for processing food, as long as its not part of the end product being consumed. Pure-Flo® Perform 6000 Data Sheet.pdf Pure-Flo® Perform 6000 Safety Data Sheet (SDS).pdf Note: Bulk Bags and Bulk sizes are non-stocked items and will be ordered as needed and carry a several weeks lead time and require a forklift or pallet jack Note: Container style and color may vary. Product is sold by weight which may result in container not being full.
$20.00 - $2,325.00
Best Value Vacs 10 Gallon Aluminum Vacuum Chamber
10 Gallon Shatter Vac Vacuum & Degassing Chamber Comes with 2 yr Limited Warranty This is a complete BestValueVac® vacuum chamber setup designed, built and 100% tested in Naperville, Illinois. With our unique patented gasket design (Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5”Hg/24hrs. Our premium Vac Vacuum & Degassing Chamber is a rigid enclosure that effectively works to remove entrapped air and other gases that could induce failure in the final product. Due to its low-pressure environment and solid vacuum design, this heavy-duty chamber can be used in a variety of vacuum applications. -Please refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart key Features: Aluminum Vessel Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User-friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum. Specification Chamber Material 3004 Aluminum Gasket Material Silicone Lid Material Acrylic Internal Dimensions (ID) 15" Tall x 14" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC Hose Platinum Cured Silicone Pad Black 50 Micro Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings. Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Exludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min. For shipping info including Import/Export details visit our Shipping link at the bottom of the page.
$300.00
BVV™ Neo Brand T-Shirt
BVV™ Neo Brand T-Shirt The newly re-designed BVV™ Neo brand T-shirt is made out of 50% Polyester and 50% Cotton it comes in black and grey and is available in the sizes listed below. Sizes Available: Medium Large X Large 2 XL
$15.00
Milwaukee Valve 316SS FNPT Ball Valve
Milwaukee Valve 316SS FNPT Ball Valve (10SSOD-02-LL) This top of the line 316 Stainless Steel Milwaukee ball valve is a fire safe ball valve and is 1 piece ball valve construction. It also features a straight body style with Female NPT x Female NPT threaded connections with one side being pinned into place for zero movement during installation. The fire safe ball valve features a maximum pressure rating of 2000 PSI CWP and has a blowout proof stem made of 316SS and the temperature range of this ball valve is -20F° to 450F°. Milwaukee 10 Series Ball Valve Spec Sheet Valve Specifications Sizes Available: 1/4" FNPT 3/8" FNPT 1/2" FNPT Pressure Rating 2000 WOG Temperature Range -20°F to 450°F Valve Materials: Body A351-CF8M Ball Retainer A351-CF8M Ball 316 Stainless Steel Stem 316 Stainless Steel Seat 304 Stainless Steel Thrust Washer 316 Stainless Steel Seat RTFE Thrust Washer RTFE Stem Packing GRAPHOIL Gland 316 Stainless Steel Handle 304 Stainless Steel Handle Nut 304 Stainless Steel Handle Nut 304 Stainless Steel Belleville Washer 304 Stainless Steel PIN 304 Stainless Steel
$75.00
BUNA-N 10 Mesh (2000 Micron)
BUNA-N 10 mesh (2000 micron) Tri-Clamp Tri Clover Gasket MADE IN THE U.S.A Mesh / Micron Filter Chart Note: 'Cinnamon' Smelling Gaskets are Chinese made and are not standardized or regulated Disclaimer: BVV™ recommends no more than a -40F operating temperature and is not responsible for the user running their system with incompatible chemicals Why BUNA-N over Viton? Lower Temperature Range Lower Costs Better Compressibility and Springiness Excellent Resistance to Major/Popular Solvents(Butane/Propane) Better Tear Resistance Better Abrasion Resistance Specifications Materials: BUNA-N (Nitrile) 316 Stainless Steel Mesh Overmold Conformance FDA Compliant / Meets 3A Standards Thermal Properties: Low-Temperature Range: -70°F Minimum for Continuous Use(Static): -40°F Brittle Point: -70°F High-Temperature Range: +210°F to +250°F Maximum for Continous Use (Static): +250°F Gas Permeability: Excellent Durometer or Hardness Range: 20-95 Shore A Tensile Strength Range: 200-3,500 PSI Elongation Range(%): 350%-650% Abrasion Resistance: Excellent Resilience / Rebound: Good Chemical Compatibility Butane A - Excellent Propane A - Excellent Alcohols: Amyl B - Good Benzyl D-Severe Effect Butyl C-Fair Diacetone D-Severe Effect Ethyl C-Fair Hexyl A - Excellent Isobutyl B - Good Isopropyl B - Good Methyl A - Excellent Octyl B - Good Propyl A - Excellent
$15.00 - $118.00
Pipe Cross
BVV™ Pipe Cross BVV™ brand stainless steel parts are made with precision 304 Grade Stainless Steel and are clean and free from burrs or debris. These fittings are NPT threads (National Pipe Taper) and will compress against other Female/Male NPT threads creating a tighter and tighter connection. All NPT threads require thread sealant to create a watertight and gas-tight seal between the threads. We recommend using Yellow Gas PTFE Tape because it is rated for gases and is UL listed and it is NOT recommended to use white PTFE tape because it is not rated for gas service. Stainless Steel Pipe Crosses are used to split flow 4 ways and create manifolds like the Bi-Flow manifold on Bidirectional extraction systems that BVV™ is known for. They can also be connected together creating even larger manifolds when combined with valves and other stainless steel fittings. BVV™ Pipe Cross - Data Sheet Specifications Material 304 Stainless Steel Connection Type 1/4"-18 FNPT 3/8"-18 FNPT 1/2"-14 FNPT Sizes Available: 1/4" 3/8" 1/2"
$20.00 - $25.00
1/4" ID Heavy Wall Spiral Wire Reinforced Clear PVC Vacuum Hose
1/4" Reinforced Clear PVC Vacuum Hose Crystal clear Phthalate Free PVC compound, formulated with ingredients in compliance with applicable FDA(03) requirements, meets USDA(18), 3A(01), NSF(13) and RoHS(16) criteria. This hose is reinforced with helically-wound spring steel wire to prevent it from collapsing under a vacuum and prevent kinking or deformation of the tubing. Key Features: Vacuum Rated to 29.9" HG @ 70°F Spiral wire reinforcement prevents kinking or collapsing and prevent expansion under higher pressure applications Crystal clear tubing allows visual confirmation of product flow Glass smooth interior prevents build-up of material inside the tubing Electrogalvanized helical steel wire can be used for static dissipation. (This product is designed to dissipate static electricity when the metal wire is properly connected to ground through the fitting or other means Resistant to wide range of chemicals Self extinguishing Non-marking Silicone Free One-piece lengths Phthalate Free! Common Applications: Full Vacuum Lines Industrial Vacuum Pumps Food and beverage dispensing Air and water supply lines Pneumatic parts transfer Car wash applications Coolant lines Air breathing lines Deionized water systems Specifications Series K1760 Sized Code 04 Service Temperature Range 25 to 150°F (-4 to 65°C) Nominal ID 1/4" (6.4mm) Nominal OD 0.460" (11.7mm) Max Working Pressure @ 70°F (20°C) 150 Psi Max Working Pressure @ 122°F (50°C) 70 Psi Standard Length Coils 100ft Approx. Wt. per Pkg. 7.0lb Brand Kuri Tec® Packaging Coils Material NSF-51 Applications / Materials Conveyed Air and Water supply lines Air breathing lines Car Wash Applications Coolant Lines Deionized Water Systems Food & Beverage dispensing Full Vacuum Lines Industrial Vacuum Lines Pneumatic Parts Transfer Min. Bend Radius @ 70°F 1" Type Reinforced Water Supply and Food Grade Hose Style Standard Wall PVC Food and Beverage Vacuum/Transfer Hose Inside Tube Material Crystal Clear Phthalate Free PVC Compound Cover Material Crystal Clear Phthalate Free PVC Compound Reinforcement Material Helically-wound spring steel wire Color Crystal Clear Medium Temperature(Min) 25°F (-4°C) Medium Temperature(Max) 150°F (65°C) Weight per Foot 0.07lbs/ft Performance Clear PVC wire reinforced for vacuum; Kink Resistant
$10.00 - $100.00
6" x 1.5" x (2) 1/4" FNPT Tri-clamp Endcap BVV™
6" x 1.5" x (2) 1/4" FNPT Tri-clamp Tri Clover Endcap BVV™ This End Cap come with Two 1/4"-18 FNPT Threaded connection and 1.5" Tri-Clamp ferrule welded to the end cap with a sanitary weld with a 0.5" Tube Extension Below the Lid. They allow the user to adapt and connect a threaded connection to the 1/4" port on a Tri-Clamp lid and the 1.5" Tri-Clamp Connection. These 3 connections are welded on a 6" Tri-Clamp End Cap. Specification Material: 304 Stainless Steel Connection Types: 1.5" Tri-Clamp - 0.5" Tube Extension Below Lid 6" Tri-Clamp 1/4" - 18 FNPT Standard: 3A BVV™ 6" x 1.5" x (2) 1/4" FNPT Tri-clamp Endcap - Drawing BVV™ 6" x 1.5" x (2) 1/4" FNPT Tri-clamp Endcap - End Cap Chart
$99.00
TR21X2 Complete Rebuild Kit
TR21X2 Complete Rebuild Kit. Please note: this item may be backordered at any time due to high volume ordering through CPS. Please excuse this inconvenience. TR21X2 CPS TR21 Oil-less Compressor Rebuild Kit. Includes TR21X4 Head, Pistons, Bearings, Eccentrics, Cylinders, O rings And Bolts. Oil-less Compressor Head Assembly Includes valves assembled ready to install. This kit is compatible with the following CPS pump(s): TRS 21 Recovery Pump TRS 600 Recovery Pump
$360.00
Pipe Nipple
BVV™ Pipe Nipple Fully threaded 304 stainless steel pipe nipple allows the user to configure a system while minimizing the length of the system due the extra hex nipple space that a wrench would need. All NPT threads require thread sealant to create a watertight and gas-tight seal between the threads. We recommend using Yellow Gas PTFE Tape because it is rated for gases and is UL listed and it is NOT recommended to use white PTFE tape because it is not rated for gas service. **NOTE: Pre-Taped option comes from BVV Pre-taped with Yellow UL Listed Gas PTFE Tape on the Male NPT threads ONLY for a +0.50c charge per male npt end. (JIC Threads DO NOT need to be taped.) BVV™ Pipe Nipple - Data Sheet Specifications Material 304 Stainless Steel Connection Type(s): 1/4"-18 MNPT 3/8"-18 MNPT 1/2"-14 MNPT 3/4"-14 MNPT 1"-11-1/2 MNPT
$5.00 - $5.50
37 Degree FJIC Swivel Union
BVV™ 37° FJIC Swivel Union BVV™ brand stainless steel parts are made with precision 304 Grade Stainless Steel and are clean and free from burrs or debris. These fittings are 37° JIC threads and will create a seal by compressing the flared end against an opposite female/male flared connection. JIC connections do not require thread sealant because they seal off the flared surface of the fitting JIC Fittings are also not the same size as NPT fittings but do have the same size nomenclature. When connecting JIC fittings to one another it is recommended by BVV™ to use 2 wrenches - 1 to tighten the fitting and 1 to hold back against the force applied to create resistance and ensure a better seal. Female JIC Swivel union allows users to attach Male JIC connectors or convert a MJIC connection to a female connection. Swivels are unique because they can be oriented to the direction the part needs to be facing. BVV™ FJIC Swivel Union - Data Sheet Specifications Material 304 Stainless Steel Connection Type(s): 1/4" 37° FJIC (7/16-20) 3/8" 37° FJIC (9/16-18) Sizes Available: 1/4" 3/8" x 1/4" 3/8"
$15.00
2" Standard Closed Column Extractor 115-200g
DISCLAIMER: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in extremely well ventilated areas. DO NOT USE INDOORS Our dewaxing closed column extractor is the primary tool for extracting maximum solvent, and is designed to increase productivity. This closed system can be filled about 85% with solvent before the internal pressure will equal the pressure of the can propellant. Adding dry ice to the dewaxing column on the outside of the extractor decreases the temperature of the extractor, which filters out coagulated waxes and lipids from being extracted. This provides a more efficient and productive extraction process. With a 2” stainless steel tube, this unit can be customized to your needs, handling everything from 90-270g of material. Pressure gauge, shower head, and sight glass can all be added to increase ease of use. Key Features and Description: Closed Column Pressure Extractor (Comes with 1 yr. Limited warranty, excludes gaskets and screens) Compound Gauge with (-30)-160 PSI readout. This system allows the user to build up solvent pressure by closing the valve, pulling a vacuum and filling the extractor, Extractor will fill about 85% with solvent before the internal pressure will equal the pressure of the can propellant. The solvent can will fit into either port with a tip adapter supplied with some butane cans, tip adapter required, not included Solvent Soak is expected to be between 30-90 min, but this all depends on material, starting with frozen cans of solvent is recommended This system allows the user to soak the material before opening the bottom valve to release the solvent and oil. Professional Kit Adds the following: Compound Gauge Sight Glass Shower Head Explorer Kit Includes the Following: 8" x 8" Platinum Cured Silicone Non-Stick Pad 2" Tri-Clamp 304 Stainless Steel Material Tube Spool Sizes Specifications: 2" x 12" = 115G 2" x 18" = 150G 2" x 24" = 200G 304 Stainless Steel Flare End Caps with Heavy Duty Stainless Steel Miniature Ball Valves (1) 2" Standard Pressure Tri-Clamp Clamps 2" Tri-Clamp Quadpod (1) Buna-N Tri-Clamp Gaskets Buna-N 100 Mesh (150 Micron) Gasket *Note: Column capacity may vary depending on the density of packed material and packing density. Capacity is calculated using the industry standard of 4.2g/in3. This is the upper limit for column capacity. Low density, uncut, and/or lightly packed material can reduce capacity by 50%. For best results, we recommend to tightly pack coarse ground material. ***Note: Parts and components can be subject to substitutions. Any substituted parts will have the same function and will be of equal or greater value.**** Material Capacity Cylinder Volume Radius (in) 1.5" 2" 3" 4" 6" 8" 10" 12" Length (in) Volume (in3) Select Material Butane ISO-Butane Propane How Much Will Fit in Cylinder FormulaVolume x Weight of Water x Specific Gravity ConstantsWeight of Water = 0.0360 (lbs / in3)Specific Gravity of = Lbs. of : Recommended: Account for an 80% fill to avoid a hydraulic lock How Much Material Will Fit in the Cylinder Volume Packing Density (g) 2.5 3 3.5 4.3 Grams of Material Lbs. of Material Cans of Butane Cans of Butane by Size Pounds of Butane mL fl oz lbs # of Cans 420 14.2 300 10.1 200 6.7 150 5.07
$152.00 - $219.00
2" Tri-Clamp Spools
2" Tri-Clamp/ Tri Clover Spools Sizes Available: 2" x 2" Tri-Clamp Spool 2" x 12" Tri-Clamp Spool 2" x 18" Tri-Clamp Spool 2" x 24" Tri-Clamp Spool Specifications: Tri-Clamp Size 2" Material 304 Stainless Steel Standard 3A High Polish Spool OD 2" Spool ID 1.87" Flange OD 2.516" Bead Center 2.218" OD = Outer Dimension ID = Inner Dimension Disclaimer to Customer: User assumes all responsibility and risks of the system for all Stainless Steel Parts bought separately to piece together a Closed Loop, Closed Column, or Open Blast Extractors. They DO NOT come with a standard 1 year system warranty, customer assistance on how to run your system, technical help or a guarantee of the system being tested. BVV™ 2" Tri-Clamp Spools - Drawing Material Capacity Cylinder Volume Radius (in) 1.5" 2" 3" 4" 6" 8" 10" 12" Length (in) Volume (in3) Select Material Butane ISO-Butane Propane How Much Will Fit in Cylinder FormulaVolume x Weight of Water x Specific Gravity ConstantsWeight of Water = 0.0360 (lbs / in3)Specific Gravity of = Lbs. of : Recommended: Account for an 80% fill to avoid a hydraulic lock How Much Material Will Fit in the Cylinder Volume Packing Density (g) 2.5 3 3.5 4.3 Grams of Material Lbs. of Material Cans of Butane Cae by Size Pounds of Butane mL fl oz lbs # of Cans 420 14.2 300 10.1 200 6.7 150 5.07
$19.00 - $42.00
Tested Valve Manifold - HVAC Flare
Tested Valve Manifold - HVAC Flare Specifications: Material: Nickel Plated Brass Connection Type 1: 1/4" SAE Flare Connection Type 2: 1/4" FNPT Connection Type 3: 5/16-18 Screw thread Valve Type: 1/4 Turn Includes washer, O-ring, Nylon Locknut
$22.00
Best Value Vacs 7 Gallon Aluminum Vacuum Chamber
7 Gallon Vacuum & Degassing Chamber (Comes with 2 Year Limited Warranty) This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: Aluminum Vessel Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum 3003 Grade Aluminum Body, lightweight and durable Precision lip edge at the top for the protection of silicone gasket Specification Chamber Material 3004 Aluminum Gasket Material Silicone Lid Material Acrylic Internal Dimensions (ID) 8" Tall x 16" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC Hose Platinum Cured Silicone Pad Black 50 Micro Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings.
$280.00
37 Degree MJIC Tee
BVV™ 37° MJIC Tee BVV™ brand stainless steel parts are made with precision 304 Grade Stainless Steel and are clean and free from burrs or debris. These fittings are 37° JIC threads and will create a seal by compressing the flared end against an opposite female/male flared connection. JIC connections do not require thread sealant because they seal off the flared surface of the fitting JIC Fittings are also not the same size as NPT fittings but do have the same size nomenclature. When connecting JIC fittings to one another it is recommended by BVV™ to use 2 wrenches - 1 to tighten the fitting and 1 to hold back against the force applied to create resistance and ensure a better seal. A MJIC Tee allows the user to connect multiple JIC hoses to their system and use it as a splitter or any other type of extractor accessory with Female JIC ends. BVV™ 37° MJIC Tee - Data Sheet
$15.00 - $17.00
Hex Adapter
BVV™ 304 SS Hex Adapter FNPT. For connection of different size/length pipes or to off the end of a pipe. Allows for pipes to be connected in a straight line, increase/decrease flow, change the direction of flow or stop the overall flow by closing the pipe. Made of durable stainless steel 304 material for long-lasting strength. BVV™ Hex Adapter - Data Sheet
$6.00 - $24.00
BVV™ Filter Dryer
BVV Filter Dryer (Compare to Mastercool 69500-DR Filter Dryer) 1/4" In-Line Liquid filter drier model SDML-032 DM Core - 100% molecular sieves recommended for HFC's with POE and PAG oils.
$15.00
4" Tri-Clamp Dewaxer Columns
4" Tri-Clamp/ Tri Clover Dewaxing Columns This is a 4" Tri-Clamp BVV™ Tri-Clamp Dewaxing Spool. It is intended to have dry ice put into the sleeve to chill the material inside the column. **Note: When selecting a Pipe Hanger choose the size that correlates to the Sleeve OD NOT Spool OD Sizes Available: 4" x 8" Tri-clamp Dewaxer Column 4" x 24" Tri-clamp Dewaxer Column 4" x 36" Tri-clamp Dewaxer Column Specifications: Tri-Clamp Size 4" Material 304 Stainless Steel Standard 3A High Polish Sleeve OD 6.000" Spool ID 3.834" Spool OD 4.000" Flange OD 4.682" Bead Center 4.344" Drain Port 1/4"-18 FNPT (Drain Plug Included) OD = Outer Dimension ID = Inner Dimension Disclaimer to Customer: User assumes all responsibility and risks of the system for all Stainless Steel Parts bought separately to piece together a Closed Loop, Closed Column, or Open Blast Extractors. They DO NOT come with a standard 1 year system warranty, customer assistance on how to run your system, technical help or a guarantee of the system being tested. BVV™ 4" Tri-Clamp Dewaxer Columns - Drawing
$105.00 - $260.00
6" Tri-Clamp Hemispherical Extractor Lid
6" Tri-Clamp Tri Clover x (3) 1.5" TriClamp x (4) FNPT Hemispherical Lid This End Cap comes with Four FNPT Threaded connection and Three 1.5" Tri-Clamp ferrule welded to the end cap with a sanitary weld with a 3" Tube Extension Below the middle port on the lid. These allow the user to adapt and connect a threaded connection to the NPT ports and three 1.5" Tri-Clamp Connections on a 6" Hemispherical Tri-Clamp lid. With this versatile Tri-Clamp Extractor Lid, users can quickly create a leak-proof connection allowing easy assembly or disassembly for routine maintenance and inspection. Specification SKU: 600HEL 600HEL-V2 Material: 304 Stainless Steel 304 Stainless Steel Connection Types: 6" Tri Clamp 3x 1.5" Tri Clamp (Tube Extension Below Center Port) 4x 1/4" FNPT 2x 1/4" FNPT - 2x 1/2" FNPT Standard: 3A BVV™ 6" Tri-Clamp x (3) 1.5" TriClamp x (4) 1/4" FNPT Hemispherical Lid - Drawing BVV™ 6" Tri-Clamp x (3) 1.5" TriClamp x (4) 1/4" FNPT Hemispherical Lid - End Cap Chart
$160.00 - $175.00
Jacketed Hemispherical Reducers with 1/2" FNPT Drain Port
Jacketed Hemispherical Reducers Jacketed Hemispherical Reducers allow the user to circulate water around the bowl and keep extracted material liquefied for easier flow through the bottom port. These jacketed reducers have 1/2" FNPT ports on either side and a 1/2" FNPT port through the bottom of the dish. These reducers are made out of 304 stainless steel with a high polish interior. Specifications Material 304 Stainless Steel Connection Type(s): Tri-Clamp 1/2" FNPT Sizes Available: 6" 10" 12"
$240.00 - $340.00
Glass Vac™ 3 Gallon WIDE Stainless Steel Vacuum Chamber
3 Gallon Wide Stainless Steel Vacuum Chamber (Comes with 2 Year Limited Warranty) This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. Glass Vac Vacuum Chambers are ideal for wood workers using the wood stabilization process because the glass lid will not deteriorate like acrylic or polycarbonate lids. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: High Strength Stainless Steel Chamber Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum. Specification Chamber Material 304 Stainless Steel Gasket Material Silicone Lid Material Glass Internal Dimensions (ID) 8" Tall x 10.5" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC Hose Platinum Cured Silicone Pad Black 50 Micro Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings. Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Exludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min. For shipping info including Import/Export details visit our Shipping link at the bottom of the page.
$145.00
1/4" Gum Rubber Tubing for Vacuum
1/4" Gum Rubber Tubing Pure gum rubber tubing is tear-resistant, ideal for vacuum applications and will not collapse under a vacuum-like other soft/low durometer tubing on the market. Please refer to this chemical compatibility chart: Cole-Parmer Chemical Compatibility - Natural Rubber Key Features: Tear Resistant Retains Memory Safely conducts many acids, chemicals, and gases Resistant to cold and hot temperature variations Very versatile Flexible and soft Developed especially for mechanical vacuum pumps Specifications Hardness Rating Soft Hardness Durometer 45A Material Gum Rubber ID 1/4" OD 3/4" Wall Thickness 1/4" Flexibility Very Flexible Temperature Range -70° to 180°F Maximum Vacuum 29 in. of Hg @ 72°F Compatible Tube Fittings Barbed Connections Color Beige
$40.00 - $400.00
1.5 Gallon Resin Trap Vacuum Chamber
1.5 Gallon High Strength Stainless Steel Chamber (Comes with 2 Year Limited warranty) Designed, built, and 100% tested in Chicago, Illinois, the Resin Trap Vacuum Chamber is the perfect application for a successful, high-quality end product. With its unique, patent pending gasket design (Utility Patent #14/533,548), this shatter chamber can easily withstand 10,000 uses with proper care and maintenance. The gasket itself is reversible, doubling the system's life by allowing customers to instantly take it off and flip it over. No adhesives necessary. The maximum allowed temperature of this chamber is 160f. The individual components of this chamber are rated at higher temperatures, however, as a vacuum vessel, we limit maximum operational temperature to 160f. Every chamber is tested prior to shipping to lose no more than 2.5inHg/24hrs. Specifications Key Features: Comes with 2 year limited warranty Resin traps come complete with glycerin-filled vacuum gauge, fittings for use with 1/4" vacuum tubing, nickel plated brass ball valve and instruction manual. Capture excess resin and protect your pump! Unique Catch Port Design: An additional hose can be installed at the port inside the tank to facilitate accurate collection of resin. 5 Feet Reinforced Vacuum Hosing to Connect Directly to the Vacuum Pump 1/4" SAE port. Measuring range of vacuum gauge：0-29.25inHg Silicone gasket to be used over 10,000 times without deterioration. This Kit Includes: (1) 1.5 Gallon High strength Stainless Steel Chamber (1) Industrial grade silicone gasket Gasket can withstand 390°F max temp. 60A durometer density (1) Glycerin filled vacuum gauge (must be regulated upon arrival) Max vacuum -29Hg (+/-.5Hg) at sea level (1) Leak free nickel plated 1/4" Hvac Flare Valve (1) ¼” Barbed Connection (1) 5' Purple BVV™ Hvac Hose (1) 5' Clear Vacuum Tubing Internal Dimensions: 8-5/8” Tall X 7-1/8” Diameter Lid Material: Acrylic Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization. The lid may be cleaned with any solvent or cleaning agent. Pump Facts: We recommend the oil is changed every 50-75 of operating hours. CFM is a measure of cubic feet per minute. Single stage pumps reach a max vacuum of 50-75 microns (0=complete vacuum). Dual/Two stage pumps reach a max vacuum of 10-15 microns (0=complete vacuum). See FAQ at the top for product safety warnings. For shipping info including Import/Export details visit our Shipping link at the bottom of the page.
$134.00
Replacement Gasket for Dutch Weave Sintered Filter Disks - Buna-N
Replacement Gasket for Dutch Weave Sintered Filter Disks This is a replacement buna-n gasket for dutch weave sintered filter disks.
$8.00 - $22.00
BVV™ 16.75" Vacuum Chamber Gasket
BVV™ 16.75" Vacuum Chamber Gasket With our unique patented gasket design (Patent #9475627) this chamber gasket is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible, allowing customers to instantly take it off and flip it over. This Gasket fits the following Vacuum Chamber Lids: Best Value Vacs 7 Gallon Aluminum Vacuum and Degassing Chamber Best Value Vacs 15 Gallon Aluminum Vacuum and Degassing Chamber
$53.00
Mini Dry Ice Shaker
Miniature Dry Ice Shaker Miniature Dry Ice Shaker for creating a faster and cleaner extract. This is a fully sealed extraction system that only requires Dry Ice to Operate. It features a removable collection cap and interchangeable filter screens. This kit includes the following filter screens: 2x -- 100 Micron Screens 2x -- 120 Micron Screens 2x -- 160 Micron Screens 2x -- 190 Micron Screens
$39.00$30.00
Hemispherical Filter Plate Reducer with 1/4" FNPT Side Port
Hemispherical Filter Plate Reducer with 1/4" FNPT Side Port This hemispherical reducer has a built-in filter plate with a 1/4" FNPT Side Port. This unique design allows the user to save even more space by combining a filter plate, hemispherical reducer, and a side port. Made out of 304 stainless steel the filter plate is welded into the hemispherical reducer and has Tri-Clamp connections on both ends of the reducer along with the 1/4" FNPT side port. Specifications Material 304 Stainless Steel Sizes Available: 3" x 1.5" x 1/4" FNPT 4" x 1.5" x 1/4" FNPT 4" x 2" x 1/4" FNPT 6" x 2" x 1/4" FNPT
$45.00 - $99.00
TRS21 Valve Rebuild Kit TR21X1
Specifications: CPS TR21 Oilless Compressor Valve Rebuild Kit includes valves, valve springs, seals and o-rings and inlet screen. This kit is compatible with the following CPS pumps: TRS 21 Recovery Pump TRS 19 Recovery Pump TRS 600 Recovery Pump
$70.00
0.9CF ECO Vacuum Oven - 4 Wall Heating, LED display, LED's - 4 Shelves Standard
DISCLAIMER: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in WELL VENTILATED AREAS! Backed with our 2 Year Parts and Labor warranty. For the easy and efficient degassing and purging light hydrocarbon solvents, look no further than our purpose-built ECO vacuum oven with LED display. Using cold-boiling, this oven applies gentle heat under reduced pressure to expedite solvent degassing while preserving color, aroma, and overall quality. The ECO vacuum oven has four (4) spacious shelves with optimal heat distribution and perfect uniformity across each shelf surface. It’s low consumption, high-throughput, and reliable, so you’ll spend less money and time getting the job done. This oven comes with a touchscreen and LEDs for easy operation, and two-year parts and labor warranty. Our ovens offer: The guaranteed industry standards ability to lose less than 1” Hg over a 24 hour period. Reliable deep vacuum that reaches below 0.1 torr. with stainless steel compression-fit tubing and stainless steel instrumentation valves. Uniform heat which is key to an effective oven. Our ovens offer 7% temperature uniformity across all shelves with offering ±1⁰ stability in temperature. Comes standard with the maximum number of shelves and a well-lit LED interior. Items Included: 5' 37⁰ female flared HVAC hose; USA power cord; and oven operation manual. You’ll get the complete package only with Best Value Vacs. Key Oven Features: 1/4" JIC Vacuum Port with included 5' HVAC Hose Easy Vac-Release Dial allows release of vacuum without disconnecting pump or purge Stainless steel interior for a sanitary, easy-to-clean look Overload circuit breaker for electrical protection Comes standard with 4 (0.9CF Eco models) or 5 shelves (1.9CF Eco models) Specifications Electrical 120 VAC / 60Hz / 700W / USA Plug Internal Chamber Material: Polished Stainless Steel Dimensions (LxWxH): 11.5" x 11.75" x 10.75" Temperature Control Four Wall Heating LED PID Controller Temperature Range - 212F Temperature Stability: +/- 1.8F or 1C Automatic Over Shoot Shut Down Over Temp Alarm Vacuum Gauge Ranging From -1inHg to -30inHg Maximum Vacuum Level -29.9inHg / 75.4 cmHg / -1 MPa Shelves Up to 8 Sliding Shelves at one Time Reinforced Steel with sides to secure product Shelf Capacity(Area): 129in^2 Total Shelf Capacity: 1034 in^2 or 7.2ft^2 Dimensions (LxW): 11-3/8" x 11-3/16" Door 1/2" Tempered Glass Window Integrated LED's Window Dimensions (LxH): 11.75" x 11" Replaceable Gasket Material: Silicone Weight & Dimensions Outside Dimensions (LxWxH): 23x18x18 Weight: 115lbs Compliance CE Listing Recognized ISO 9001:2008 ISO 13485" 2003 Manufactured in Acc. w/ Q/TIWY7-2004 IEC68-2-3 Note: This oven does NOT contain a vacuum pump. External pump is required to achieve vacuum pressure Note: This item is a freight ship item and will ship Via UPS ground Freight. Expedited freight can only be calculated by calling customer service 331-281-0154. All orders with expedited freight through the website will not be honored and will need to be re-quoted. A valid Phone Number IS REQUIRED to ship, Otherwise UPS freight Cannot Contact you for a delivery setup window. Freight Time is 2-5 Days. West Coast 5 Days, Midwest 2 days, East Cost 3-4 days.
$1,225.00 - $1,275.00
You have seen 144 out of 805 products