All products
High Pressure Wood Stabilizing Chamber
High Pressure Wood Stabilizing Chamber A BVV EXCLUSIVE! This is our high pressure wood stabilizing column that can perform rapid wood stabilization @ 1600 PSI (1.5" Diameter Tube) & 450 PSI (3"/ 6" Diameter Tube). This extreme pressure makes the toughest woods easy to impregnate with wood stabilizer in as little as 15min. Then its off to the oven for a quick cure and its finished. The blanks in the photo, all 3 were stabilized and cured in less than 1 hour and 15 min, including cleanup. The system is simple. Load your blanks into the column and fill no more than 80% with resin. (make sure the blanks are submerged) Then close the system and turn on the pump set to 1600 psi. Watch the video and check out the instruction manual for details. High Pressure Wood Stabilizing Manual with Assembly The compressor you will need can be ordered from this site (GX Pumps Click This Link). BVV does not yet carry the compressor for this system. But our hose will connect directly to the compressor. If the compressor is out of your reach a high pressure hand pump can be used. (GX Hand Pumps Click This Link) The system comes with an installed safety pressure relief burst disk rated for 1800 PSI. (1.5" Diameter tubes) & 450 PSI. (3"/ 6" Diameter tube) Should you exceed the pressure of the system the disk will rupture releasing pressure. What's Included Wood stabilizing manual *Coming Soon 3/1/24 for 3"/ 6" Diameter. Braided stainless steel hose 2500 psi rated. Main column, stand and top cap valve manifold assembled. Extra safety burst disk, for 1.5" Diameter Tube. 3"/ 6" Tubes self reset. BVV warranties the main column to be free from any defects for 1 year. All other individual components may hold separate warranty periods. BVV does not warranty any claims where resin has been released/backflowed into the manifold hose or valve. Resin is water washable and should be cleaned after each use, especially if resin has accidentally backflowed into the manifold area.
$255.00 - $726.00
Oil Filled Vacuum/Pressure Gauge - Bottom Mount - 1/4" MNPT
Oil Filled Vacuum/Pressure Gauge The Oil Filled Vacuum/Pressure Gauges have internal parts that are permanently lubricated to assist in smooth movement and fine tuning of the needle. All models are bottom mount with a 1/4" MNPT brass connection. All positive pressure is measured in both PSI and Bar. Negative pressure is measured in inHg and Bar. BVV™ Gauge - TDS
$10.00
AFS Ultra Clear Cartridge
BVV™ AFS Disposable Ultra Clear Cartridge Note: Stainless Steel filter housing sold separately. (Click Here for Housing) AFS Instruction Manual Download Here AFS Filters are the first and only disposable color remediation filter cartridges for the botanical extraction industry. The Patent Pending design allows for an easy to use solution implemented into existing extraction systems; and is now available as a standard integration from many equipment manufacturers. AFS Filters are a simple solution that allows for the use of prepackaged filters, which are available in different recipes depending on the application. With the integrated 2.5µm paper filter molded and sealed into the cup there is no media leak through. Pre-packed means there's no need to be an expert in remediation filter media and how to construct filters; as well as eliminates the messy process of building/packing filters yourself. Disposable offers no need for cleaning the filter housings afterwards and trying to un-clog stainless filter screens. Less R&D investment, less mess, and less down time allows for higher throughput and more profit. The media contained in the BVV™ Ultraclear filter cartridge is Ultra-clear is a high-performance granular attapulgite that is effective in removing a wide range of polar impurities including color bodies, surfactants, water, and free fatty acids while maintaining target compounds. As a granular media Ultraclear is easy to use, safe to handle, and does not require baking or wetting before use. Using only made in the USA materials that are FDA-GRAS. Technical Specifications: Life Span: 1 Time use, Good for 5-7 lbs. of dry material. Temperature Rating: -40°C-70°C Top Seal: Induction Sealed (No glue is used) Filter: Cellulose Paper Pressure Rating: Recommended 60psi, Paper will hold 80-90 psi Max. Media: USA Made High-performance granular attapulgite Shell Material: Polypropylene Excellent compatability and Safe for chemicals in our industry (Butane, Propane, Ethanol). Pressure Method: Nitrogen Assist, unless you open blast CRC. Then you can assist with an air compressor. AFS Cup weight: 48g Media Fill Volume: 110-120g Recommend Minimum Biomass: 1lb (lesser biomass will see drastic yield losses) AFS Safety Data Sheets *Please recycle your spent Cartridges. *Yield losses under refinement are to be expected but overall potency will be retained and will proportionally increase.
$55.00
BVV™ Terpenes Goji
BVV™ Terpenes Goji All sales are final. Orders can be refunded prior to fulfillment and shipping but once the order has been fulfilled and/or shipped, no refunds will be issued. Due to the hazardous nature of our product, we are unable to accept returns. BVV™ Terpenes are botanically derived terpenes enhanced with "nature-identical" artificial flavors. These flavors boost the natural flavor profile of the terpenes, providing the user with a more pleasant vaping experience. In order to provide complete transparency and elicit customer confidence, all ingredients are disclosed in the technical data sheet. BVV Goji Safety Data Sheet BVV Apple Jack Technical Data Sheet Goji: Goji OG has a unique fruity aroma. It will not only have soothing effects, but will give an uplifted, energetic focus. This sweet, red berry, licorice scented strain is a cross of Snow Lotus and Nepali OG, creating a sativa-dominant hybrid. FRAGRANCE: Spicy, herbal, sweet, licorice EFFECT: Uplifting, happy, hungry, euphoric Storage Requirements: Keep in the original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials, and hot surfaces. Store below 15℃ (60℉). Improper storage can cause terpenes to degrade. Dilution: Terpenes must be diluted prior to use for flavor and effect (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With Care: Can cause skin irritation, do not ingest PRIOR to dilution.
$10.00 - $150.00
Diamond Sauce Separator Basket Dutch Weave 100 Micron
BVV Diamond Sauce Separator Baskets for your Diamond Sauce Separator sold "A la Carte" The 6" long basket fit the BVV DSS-9 The 8.25" long basket fit the BVV DSS-12 The basket is a Dutch Weave all 304 Stainless Steel basket, and fits inside a 3" tri-clamp spool. The lip perfectly fits the tri clamp flange and works with our Dutch Weave product line gaskets.
$21.00 - $26.00
12" x (3) 2" x (2) 1/4 FNPT Endcap with Diptube
12" x (3) 2" x (2) 1/4 FNPT Endcap with diptube This End Cap come with a 11-5/16" long diptube, Two 1/4"-18 FNPT Threaded connection and Three 2" Tri-Clamp/ Tri Clover ferrule welded to the end cap with a sanitary weld with a 0.5" Tube Extension on center ferrule Below the Lid. They allow the user to adapt and connect a threaded connection to the 1/4" port on a Tri-Clamp lid and the 2" Tri-Clamp Connection. These 5 connections are welded on a 12" Tri-Clamp End Cap. Specification Material: 304 Stainless Steel Connection Type: 2" Tri-Clamp - 0.5" Tube Extension on center ferrule Below Lid 11-5/16" Diptube 12" Tri-Clamp 1/4" - 18 FNPT Standard: 3A
$235.00
20L Solvent Pro Rotary Evaporator Nut and Washer Flask Set
Replacement nut and washer flask set for 20L Solvent Pro Rotary Evaporator
$136.00
20L Neocision Dual Short Path Distillation Turnkey System
20L Neocision Dual Short Path Distillation Turnkey System This unit carries a 2 day lead time. (Note: This kit does NOT include the stainless steel table.) The 20L Neocision Distillation Turnkey Setup features our Dual USA made P10V6 Distillation Heads. Every component in this distillation kit is made for precision, throughput, and repeatable results. You will also receive Dual Dewar Style Ribbed Glass Cold Traps to keep all volatiles and solvents out of your vacuum system. This Turnkey Setup gives you everything needed to perform distillation at the highest level. The 20L Neo Kit Includes: 20L Neocision Kit with glassware, labware, and Dual P10V6 Distillation Heads. BVV 15 Liter Advanced Digital Heated Circulator Choice of Vacuum Pump KF-25 Bellow Y Manifold Dual Ribbed Dewar Style Glass Cold Trap Non-Mercury Glass Thermometers 20L Digital Heating and Stirring Mantle Distillation Quick Start Guide This guide gives basic quick start instructions for distillation systems. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs, Before beginning distillation, ensure the following steps have been taken: Vacuum Pump is in good working order. Pump should be run against dry load to allow internals to warm up. Oil should be clear. Cloudy or dark oil should be changed. All glass components are in good working order and ready to be assembled A winterization and degassing procedure has been done to prepare oil for distillation The unit's max internal temperature cannot exceed 380C. The recommended max set temperature should not exceed 250C Once all three of these steps have been completed, you are ready to begin distilling. Begin by placing stir bar in the boiling flask and then load your material. This should be done using a funnel. A small amount of alcohol in the oil will give it a thinner consistency making it easier to transfer. Assemble all glassware and ensure each joint is properly greased. Do not use too much, as the vacuum pressure might pull some grease into the system. To ensure a full seal, spread grease in a circular motion by rotating glassware Attach circulator to condenser and set temperature to 50C. Allow circulator to reach temperature before beginning distillation. Connect vacuum pump to manifold. The manifold will allow you to isolate each individual component as well as let atmosphere into and out of the system. Connect receiving cow to cold trap. Connect cold trap to manifold. Connect vacuum gauge to manifold. At this point, ensure all connections are correct. Also ensure receiving cow is positioned to collect the first fraction in the far-left receiving flask. Circulator should be at its set temperature. Turn on vacuum pump to begin process. Turn on heat and set to 60C. Vacuum pump will begin to pull down and temperature will begin to rise. Watch the gauge to monitor vacuum pressure and stability. Start stir slower and increase speed with temperature. Once you are close to 60C, increase the temperature 20 degrees. Continue to raise the heat incrementally in 20-degree steps, increasing the set temperature as you near your set point. Increase temperatures incrementally until you reach 220C. You will see your first fraction somewhere between 180C and 190C or slightly before. This is the “heads” fraction. You will move to your second fraction when you see an increased reaction in the head, a slight color change toward golden, as well as a thickening of distillate. When this fraction hits, allow the distillate to “self-clean” the head for a minute or two then, rotate the cow to the middle receiving flask. Collect your “main body” fraction. You will see temps between 190-220C during this fraction. Continue to increase stirring speed as necessary. Reaction in the head may vary but it should never stop. As fluid level in the boiling flask decreases, increase stir speed. The final “tails” fraction is a mixture of the first and second fractions and should be saved for re-distillation later. Ideally, you want to turn the cow to the final flask before the tails fraction hits. The “tails” fraction has an obvious color change and will be darker than the “main body” fraction. You will see temps between 200-250C during this fraction. As fluid level in the boiling flask decreases even more, set stirring RPM higher (1000+ RPM). You may need to compensate with a bit more heat to finish of the final fraction as well. Once process is complete, stop heat, stop stir, and stop vacuum. Let atmosphere into the system. Be sure to properly store your distillate as exposure to air and light can cause oxidation. ***Note: This entire setup will ship via motor freight.*** *Notice to Customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. BVV™ is not responsible for the failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail, which can cause bodily harm or damage to the surrounding area.
$13,000.00 - $17,000.00
Welch DryFast Collegiate Diaphragm Pump 2014
DryFast Collegiate Diaphragm Pump 2014 ***Note: This item has a possible 1-2 week lead time depending on stock availability*** Product Details Chemical Resistant Oil-Free Tuneable Vacuum Welch DryFastTM PTFE Diaphragm Vacuum Pumps enable precise vacuum control for organic evaporations with exclusive Advanced Vapor Management (AVM). Oil-Free, portable, chemical resistant, 1 head diaphragm design simplifies maintenance. Choose from seven dry PTFE vacuum pump models with flows up to 70 L / min and adjustable vacuum down to 2 Torr. Economical DryFastTM vacuum pumps are perfect for tough lab applications. Model Number 2014 Applications Vacuum Filtration, SPE, Rotary Evaporations (volatile solvents <80oC B.P., volume <2 liters), pumping harsh vapors & gases, general laboratory vacuum Type Laboratory Vacuum Pump Free Air Displacement cfm (l/min.) @60Hz 1.2(35) Free Air Displacement m3/hr (l/min.) @50Hz 1.75(29) Ultimate Pressure 40(53) Maximum Vacuum 28.3 Motor Horsepower (watts) 1/5(150) Adjustable Vac. / Gas Ballast Yes Tubing Needed 1/4(7) Intake Thread NPT M14(1/8) Overall Dimensions LxWxH in. (cm) 12x7.0x8.3 (30.5x 17.8x21.1) Ship Weight 19(8.6) Shipping Carton Dimensions LxWxH in. (cm) 21x14x15 (52x35x37) Adjustable Vacuum Knob
$1,602.00
HTP The Monster Press - 8 Ton
HTP The Monster Press - 8 Ton If you have a large amount of plant material and are looking for a quality press then the Monster Press is for you! These high-quality presses are built from Aircraft Aluminum and stainless steel designed to be used in conjunction with a unique heating process.The Monster Press exerts 8 Tons of pressure to output a maximum shape of 5”x 7” x 3” thick.High Tech Pipes make quality presses that are manufactured in the U.S.A. using American materials and labor. Each Press is assembled and individually inspected before shipping. Our Presses are designed to be heated to the ideal temperature which is an important aspect of the Pressing process. We design and build our products to stand the test of time and to become a permanent piece of equipment for the end user. We use aircraft aluminum which maintains heat as opposed to other Presses on the market which use steel that either quickly loses heat or heats up too fast thus destroying the material that is being pressed. Each Press comes with full step by step instructions and a video is available as well.
$934.95$895.00
24/29 Valve
24/29 Valve For 10L-50L Best Value Rotary Evaporators. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$35.00
Edwards E2M28 21 CFM Dual-Stage High Capacity Vacuum Pump
Edwards E2M28 21 CFM Dual-Stage High Capacity Vacuum Pump ***Note: This item Will Ship by Freight only*** The EM range of oil‑sealed rotary pumps – renowned for their high ultimate vacuum, rapid pumping speed, quiet operation and ability to handle vapor – have become the industry standard for laboratory and light industrial applications. The pump is a freestanding unit with the drive provided through a flexible coupling by either a single‑phase or three‑phase (four pole) air cooled motor.Each EM pump is supplied with 2 x 1 liter of Ultragrade 19 oil, O ring and centering ring, two Allen keys and spares seal for oil drain and filter plugs. For PFPE prepared FX pumps Fomblin® to be ordered separately. Technology The motor is totally enclosed and is cooled by the motor-cooling fan which directs air along the motor fins. The motors are fitted with a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart.An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior after the pump stops. The pumping chambers are air-tight, so this arrangement also prevents suckback unless the gas ballast valve is open.You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has two oil drain-plugs to allow either gravity oil drain or pressure oil drain. Features and Benefits The pump is designed for reliable, long‑term operation. Thermal overload device prevents overheating (single phase only). The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor. The motors are totally enclosed and are cooled by the motor cooling fan. Full height O ring sealed oil sight glass for easy checking of oil level and condition. Large sight glass and operating oil range. IE3 energy efficient 3 phase motor used with E2M28. Edwards E2M28 21 CFM Dual-Stage High Capacity Vacuum Pump. The EM range of oil-sealed rotary pumps - renowned for its high ultimate vacuum, rapid pumping speed, quiet operation and ability to handle vapour - has become the industry standard laboratory and light industrial applications. The E2M28 pump is a two-stage, direct drive, sliding vane pump. The pump is oil sealed and designed for reliable, long-term operation in both laboratory and industrial environments. The pump is a freestanding unit with the drive provided through a flexible coupling by either a single-phase or three-phase (four-pole) motor. Specifications Displacement 50Hz 32.2 m3h-1 / 19 ft3min-1 60Hz 38.9 m3h-1 / 22.3 ft3min-1 Speed (Pneurop 6602) 50Hz 27.5 m3h-1 / 16.2 ft3min-1 60Hz 33.0 m3h-1 / 19.5 ft3min-1 Ultimate vacuum (total pressure) without gas ballast 1 x 10-3 mbar / 7.5 x 10-4 Torr with gas ballast 1.5 x 10-2 mbar / 1.1 x 10-2 Torr with Fomblin® 1 x 10-2 mbar / 7.5 x 10-3 Torr Inlet connection NW25 flange Outlet connection** Nozzle 15 mm external Ø removable from 3/4 in BSP tapped hole Max allowed pressure at outlet 0.5 bar gauge / 7 psig Max water vapour pumping rate – GB II 220 gh-1 Max inlet pressure for water vapour 30 mbar / 23 Torr Max water vapour pumping rate 0.7 kg h-1 Operating temperature range 13 – 40 °C Nominal rotation speed 1440 / 1720 rpm Motor power 50 Hz 0.75 kW Motor power 60 Hz 0.90 kW Power Connector 1-ph* IEC EN60320 C19 Weight 44 kg / 97 lbs Noise 57 dB(A) @ 50 Hz Oil capacity - max 1.5 litre Oil capacity - min 1.2 litre Recommended oil (supplied) Ultragrade 19 * Pumps listed with IEC connector only ** The FX are supplied with NW25 outlet connection ** POWER CORD NOT INCLUDED. RECOMMEND FOR CUSTOMER TO WIRE PUMP TO OUTLET WITH EXACT LENGTH. DO NOT USE EXTENSIONS** **RECOMMEND FOR CUSTOMER TO HAVE ELECTRICIAN WIRE PUMP TO OUTLET WITH EXACT LENGTH** Pump Warranty Information Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$8,653.00 - $10,402.00
6" x 4" x 3" x (2) 1/4" FNPT Tri-Clamp Skylight
Specifications: 304 Grade Stainless Steel Reducer 'Skylight' w/ High Polish interior 6" Triclamp x 4" Triclamp x 3" Triclamp (Can be used as viewport to see inside) x (2)1/4" FNPT 7" Tall
$175.00
Harvest Right Home Pro Freeze Dryer
Harvest Right™ Home Pro Freeze Dryer Fresh Food Per Batch18-27 lbs. Fresh Food Per YearUp to 5000 lbs. Tray Space1107 sq. inches Features Tray space: 1,107 square inches Freeze dry 18 to 27 lbs. fresh food per batch Freeze dry up to 5,000 lbs. fresh food per year (This would require a person to use the freeze dryer 4 times a week for 50 weeks a year) Dimensions Freeze dryer exterior dimensions: 21.3″ W x 27.5″ D x 31.3″ H Dimensions (without door or vacuum fitting): 20.25" W x 23.75" D x 31.3" H Perfect for counter top, cart, or table. Tray dimensions: 9″ W x 20.5″ x 0.75″ H Weight of freeze dryer: 143 lbs. 10 CFM industrial vacuum pump included/no extra cost ($895 value) Power 110 volt (NEMA 5-20) outlet. A dedicated 20 amp circuit is required Shipping Info The large freeze dryer ships in one package with a total weight of 243 lbs. Item will only be delivered to physical addresses. One freeze dryer package: 29″ W x 38″ D x 48″ H. Maintenance Replace vacuum pump oil every 20 to 30 batches (takes about two minutes) Clean freeze dryer as needed. Warranty Three year limited warranty. What's Included -Large Pro Freeze Dryer -Premier Industrial Vacuum Pump -Vacuum Pump Oil -Oil Filter -Stainless Steel Trays (set of 6) -Guide to Freeze Drying -Mylar Bags (50 ct) -Oxygen Absorbers (50 ct) -Impulse Sealer
$3,595.00 - $5,290.00
Active Air Commercial Humidifier, 75 Pint
Active Air Commercial 75 Pint Humidifier AAHC75PIf you live somewhere with cold, dry air, you know that parched skin and a raspy throat usually come with the territory. In very low humidity conditions the photosynthetic process within the plant slows and this leads to stress, slow growth and compromised yield. Don’t let your plants suffer any longer! The Active Air 75 PPD Humidifier features a multi-directional fogging head and direct water connection. This premium humidifier features an industrial grade motor for many years of use. Connects directly to your water supply (uses 1/4" tubing) Ultra-Fine Mist - up to 75 pints per day output Multi-directional fogging head Industrial-grade motor Coverage up to 320 sq. ft
$473.18$384.46
1" FNPT X 1.5" Tri-Clamp Top Cap
1" FNPT X 1.5" Tri-Clamp Top Cap These tri-clamp end caps: Have a 1" Female NPT connection Are made of 304 stainless steel
$16.00
CHEMTEK W2 Heat Activated Natural Bleaching Clay
CHEMTEK W2 Heat Activated Natural Bleaching Clay W2 is a natural bleaching clay offering mild yet efficient results. It is heat activated to increase its adsorptive power without the use of any acids. The lack of acid prevents terpene isomerization and keeps the terpene profile the same while also slowing the oxidation rate of the oil thus increasing its shelf life. W2 is heavier in bulk density giving it lower oil retention. W2 SDS W2 Technical Data Sheet
$50.00 - $250.00
6" - 12" Dewax Dry Ice Funnel
This stainless steel funnel is meant to help get dry ice into 6" - 12" Dewaxing columns. It simply clips on the side of the dewaxer allowing an easier filling of the dry ice into the dewaxing column.
$65.00
True Terpenes Forbidden Fruit
True Terpenes Forbidden Fruit Fragrance: Cherry Blossom Grape Fruit Cedar Floral Musky Effects: Relaxing Soothing Uplifting Forbidden Fruit delivers on its name. Created by crossing two flavor forward cultivars Cherry Pie and Tangie, this profile is temptingly good. Storage Requirements: Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store in a cool dry place. Improper storage can cause terpenes to degrade. Dilution: Terpene Strain & Flavor-Infused Strain Profiles, Effects-Based Terpene Profiles & Terpene Flavors:The Terpene products above must be diluted prior to use. (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Viscosity Extract Modifier: The Terpene product above must be diluted prior to use. (1-3% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With Care: Can cause skin irritation, do not use PRIOR to dilution. Forbidden Fruit-Specific Certificates: Product Specification Certificate of Analysis Safety Data Sheet Food Safety Company-Specific Certificates: ISO 9001:2015 GMP Certification FSSC 22000
$121.50 - $2,250.00
Glas-Col Stirmantle
Glas-Col Stirmantle Glas-Col offers two types of StirMantles: Electromagnetic (50 to 750 rpm) and Motor Driven (100 to 1850 rpm). The maximum rpms available for each type depends on the viscosity of the solution being heated. Electromagnetic StirMantles are typically used with aqueous solutions like water, while the Motor Driven units use a powerful magnet for higher viscous solution like oils. StirMantles withstands 400°C internal operating temperature. EMS series include the heating mantle, speed control and stir-bar. TEM series only includes the heating mantle and allows the customer in select different speed control options or combined speed/temperature packages like the 104A HS112. WARNING: chemical spillage, overheating, overloading, and general misuse will greatly reduce service life! Note: The temperature probe this mantle comes with can only be used with a thermowell. If you are using it with BVV™ glassware you will need to add SKU: TK1/4-12 or TK1/4-18 depending on what mantle size is selected.
$1,000.00 - $1,450.00
Straight Inlet Adapter with Hose Barb
Straight Inlet Adapter with Hose Barb This straight inlet adapter allows the user to connect a male and female 24/40 jointed connection and attached a flexible hose for vacuum if needed. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$30.00
P2V4 Neocision Distillation Head - USA Made
P2V4 Neocision Distillation Head P2V4 Short Path Distillation Head includes 4 sets of Vigreux with 24/40 Joints and GL-14 Barb Connections. Key Features: MADE IN THE USA Designed for 1 & 2 Liter Flasks Set of 4 Vigreux to allow for better seperation of fractions without packing material Larger vacuum jacket allows for less heat loss during distillations Larger vapor path to allow for gas/vapor phase flow Increased internal diameter for faster, more efficient fractioning as well as packing and unpacking of media Increased condenser length and diameter for more efficient condensation of vapor with zero clogging *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$800.00
5L Short Path Distillation Kit with P5 Distillation Head
5L Short Path Distillation Kit with P5 Distillation Head This unit carries a 2 day lead time. The 5L Distillation Kit includes everything needed to perform distillation excluding the vacuum pump and chiller. This kit features our USA made P5 Distillation Head, as well as USA, made glass. This Kit is designed for high volume production with the highest quality components for precise, repeatable results time and again. This Kit Does NOT include a vacuum pump or chiller. Please see the below recommendations for both as well as recommended add-ons. Recommended Vacuum Pumps: Pro Series 11.3CFM Corrosion Resistant Two Stage Vacuum Pump (recommended option) Just Better 6 CFM 2 Stage Deep Vacuum Pump (economy option) Recommended Chillers: Polyscience 7 Liter MX Heated Circulator (economy option) Polyscience 7 Liter Refrigerated Circulator (premium option with chilling capability) Recommended Add-Ons: Glass Dewar Style Cold Trap (recommended cold trap) Bullseye Precision Vacuum Gauge (premium vacuum gauge for measuing depth) CT40 or CT80 Electronic Cold Trap (electronic cold trap, dry ice replacement) J-KEM Digital Vapor Temp Monitor (digital vapor temp monitor with data-logging capabilites) Specifications: Boiling Flask Size: 5L Receiving Flask Size: 2x 500mL, 1000mL Batch Capacity approximate: 1000-2500 grams Run time: 4 to 8 hours dependent upon material composition and throughput Distillation Temperature Range: 140-250C (Do not exceed 250C) Recommended Condenser Temperature: 40-50C This Kit Includes: Glass components: 5L Boiling Flask P5V6 Distillation Head Triple Neck Cow 2x 500mL Receiving Flask 1L Receiving Flask 120mm Glass Funnel Accessories: PTFE Magnetic Stir Bar Retriever 5 Pack of Metal Keck Clips Dow Corning High Vacuum Silicone Grease Tripod Stand 5L Digital Heating and Stirring Mantle 3-Finger Adjustable Clamp 0-77mm 6" x 6" Scissor Jack 500-1000mL Cork Stand 2x 24/40 ChemglassPTFE Thermometer Inlet Adapter 10ft of Gum Rubber Vacuum Hose 10ft of Silicone Chiller Hose 1/4" Vacuum Manifold Traceable Kangaroo Thermometer - Digital 10 Pack of Adjustable Stainless Steel Tubing Clamps Fiberglass Insulation Rope 10 Feet 1.5 Gallon Cold Trap (2QT Tank) Dry Ice, Liquid Nitrogen w/ 2x 1/4" Barb Adapters Distillation Quick Start Guide This guide gives basic quick start instructions for distillation systems. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs, Before beginning distillation, ensure the following steps have been taken: Vacuum Pump is in good working order. Pump should be run against dry load to allow internals to warm up. Oil should be clear. Cloudy or dark oil should be changed. All glass components are in good working order and ready to be assembled A winterization and degassing procedure has been done to prepare oil for distillation The unit's max internal temperature cannot exceed 380C. The recommended max set temperature should not exceed 250C Once all three of these steps have been completed, you are ready to begin distilling. Begin by placing stir bar in boiling flask and then load your material. This should be done using a funnel. A small amount of alcohol in the oil will give it a thinner consistency making it easier to transfer. Assemble all glassware and ensure each joint is properly greased. Do not use too much, as the vacuum pressure might pull some grease into the system. To ensure a full seal, spread grease in a circular motion by rotating glassware Attach circulator to condenser and set temperature to 50C. Allow circulator to reach temperature before beginning distillation. Connect vacuum pump to manifold. The manifold will allow you to isolate each individual component as well as let atmosphere into and out of the system. Connect receiving cow to cold trap. Connect cold trap to manifold. Connect vacuum gauge to manifold. At this point, ensure all connections are correct. Also ensure receiving cow is positioned to collect the first fraction in the far-left receiving flask. Circulator should be at its set temperature. Turn on vacuum pump to begin process. Turn on heat and set to 60C. Vacuum pump will begin to pull down and temperature will begin to rise. Watch the gauge to monitor vacuum pressure and stability. Start stir slower and increase speed with temperature. Once you are close to 60C, increase the temperature 20 degrees. Continue to raise the heat incrementally in 20-degree steps, increasing the set temperature as you near your set point. Increase temperatures incrementally until you reach 220C. You will see your first fraction somewhere between 180C and 190C or slightly before. This is the “heads” fraction. You will move to your second fraction when you see an increased reaction in the head, a slight color change toward golden, as well as a thickening of distillate. When this fraction hits, allow the distillate to “self-clean” the head for a minute or two then, rotate the cow to the middle receiving flask. Collect your “main body” fraction. You will see temps between 190-220C during this fraction. Continue to increase stirring speed as necessary. Reaction in the head may vary but it should never stop. As fluid level in the boiling flask decreases, increase stir speed. The final “tails” fraction is a mixture of the first and second fractions and should be saved for re-distillation later. Ideally, you want to turn the cow to the final flask before the tails fraction hits. The “tails” fraction has an obvious color change and will be darker than the “main body” fraction. You will see temps between 200-250C during this fraction. As fluid level in the boiling flask decreases even more, set stirring RPM higher (1000+ RPM). You may need to compensate with a bit more heat to finish of the final fraction as well. Once process is complete, stop heat, stop stir, and stop vacuum. Let atmosphere into the system. Be sure to properly store your distillate as exposure to air and light can cause oxidation. *Notice to Customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. BVV™ is not responsible for the failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail, which can cause bodily harm or damage to the surrounding area.
$2,200.00
Economy Recirculating Heater Kit
Economy Recirculating Heater Kit The Economy Recirculating Heater Kit is designed to provide efficient heating and circulation at an affordable price. The kit includes a submersible water pump for fluid circulation, an LX or MX immersion heater, and all tubing and hose clamps needed to pair with your system. The tubing is 1/2" ID x 5/8" OD and the pump fitting is 1/2". The pump will circulate up to 594 GPH. Economy Recirculating Heater Kit Includes: Polyscience LX or MX Immersion Circulator EcoPlus Eco 633 Fixed Flow Submersible/Inline Pump 594 GPH 5 Gallon Aluminum Pot 10 Feet of 1/2" Silicone Tubing 10 Pack of Adjustable Stainless Steel Tubing Clamps
$1,700.00
Welch 6.1 cfm Full Chemical-Resistant 8-Head Diaphragm Pump
Welch 6.1 cfm Full Chemical-Resistant 8-Head Diaphragm Pump The Welch 6.1CFM Full Chemical-Resistant 8-Head Diaphragm Pump is the ideal choice for 50L Rotary Evaporators and large oven systems. This high capacity, full chemical resistant pump gives users the ability to vac down large capacity spaces quickly, efficiently, and cleanly without worrying about contamination of pump oil. The inner diaphragm is lined with PTFE making it highly chemical resistant and long lasting. It is one of the quietest and cleanest running vacuum pumps on the market. Key Features: Fully Chemical-Resistant Oil-less diaphragm style vacuum pump High capacity vacuum capability Specifications: Electrical Requirements: 110v 60Hz single phase Pumping Rate: 6.1cfm / 174L/min Gasket Material: All-PTFE Ultimate Vacuum level: 6 torr / 8 mbar Maximum Vacuum: 29.9 inHg Inlet / Outlet: KF16 Flange Adjustable vac. / gas ballast: No Unit dimensions (LxWxH in): 21x10x12 in Shipping dimensions (LxWxH in): 28x15x20 in Shipping weight (lbs): 90 Technical Data Free Air Displacement @ 60 Hz, cfm (L/min) 6.1 (173) Ultimate Pressure, torr 6 Motor Power, HP (kW) at 60 Hz Motor Power, HP (kW) at 60 Hz Inlet (Exhaust) Connection Thread NPT NW16 - 1/4" NPT Tubing Needed, I.D. in. (mm) Hose Connector Available Weight, lbs (kg) 72.3 (32.8) Dimensions, LxWxH, in (mm) 21x11x12 (530x280x310) 115V Order Number 2064B-01 ***Note: Purchase of this pump is subject to End User Verification. A certification form must be filled out before completion of purchase.***
$5,864.00
5L BVV™ Rotary Evaporator Glass Axis
Glass axis for 5L BVV™ Rotary Evaporator *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$50.00
Branch Tee
SSP - Branch Tee SSP Instrumentation TruFit® is manufactured from fully-traceable raw material to close tolerances and superior surface finishes. TruFit® provides optimal performance when installed in accordance with SSP’s recommendations and the design parameters appropriate for each type of connection – tapered thread, straight thread, and weld & braze. TruFit® components are cleaned in accordance with SSP documented work instructions using equipment calibrated to NIST standards with environmentally-safe and stable agents, ultrasonics, and heat/ temperature to remove all residual oil, grease, and loose particles. Stainless steel components are passivated to the requirements of MIL QQ-P-35 and ASTM A 967. ***Note: ALL NPT Threads REQUIRE the user to properly install the fitting by using a thread sealant to prevent leaks. BVV recommends GAS PTFE Tape Specifications Connection Type 1 Female NPT Connection Size 1 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Working Pressure (PSIG) 1/4" - 7750 3/8" - 6800 NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA! Dimensions A 1.76 in E 0.28 in H 3/4 in P 1/4 in L 0.88 in S 1.09 in
$30.00
Dry Utility Vacuum/Pressure Gauge - Center Back Mount
Dry Utility Vacuum/Pressure Gauge - Center Back Mount 1/8" MNPT brass Connection
$12.00$7.00
Pipe Cap
SSP - Pipe Cap SSP Instrumentation TruFit® is manufactured from fully-traceable raw material to close tolerances and superior surface finishes. TruFit® provides optimal performance when installed in accordance with SSP’s recommendations and the design parameters appropriate for each type of connection – tapered thread, straight thread, and weld & braze. TruFit® components are cleaned in accordance with SSP documented work instructions using equipment calibrated to NIST standards with environmentally-safe and stable agents, ultrasonics, and heat/ temperature to remove all residual oil, grease, and loose particles. Stainless steel components are passivated to the requirements of MIL QQ-P-35 and ASTM A 967. ***Note: ALL NPT Threads REQUIRE the user to properly install the fitting by using a thread sealant to prevent leaks. Best Value Vacs recommends GAS PTFE Tape Specifications Connection Type 1 Female NPT Connection Size 1 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Working Pressure (PSIG) 1/4" - 7750 3/8" - 6800 NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!
$5.00 - $6.00
Edwards RV8 6.9 CFM Dual-Stage Vacuum Pump
Edwards RV8 6.9 CFM Dual-Stage Vacuum Pump Edwards RV pumps have become the industry standard for scientific primary pumping applications. RV pumps are uniquely capable of delivering high or low throughputs with high ultimate vacuum. This, combined with ultra-low noise levels, makes them ideal for a wide range of applications including GCMS and other small bench top type applications.All pumps are approved to UL standards by an external test house. Edwards has a global network, providing world-wide support for product applications and service.Supplied with: 1 litre of Ultragrade 19 oil, inlet filter and O-ring. Fomblin must be purchased separately for PFPE RV pumps. Technology All our RV pumps are significantly quieter noise levels of 48 dBA 50Hz are typically half the noise of a conventional pump and have been achieved by extensive work on the drive train and motor. The pumps have the unique ability to deliver excellent ultimate vacuum in both high vacuum and high throughput modes with or without gas ballast. This gives the user an unrivalled opportunity to select the optimum pumping performance without compromising the application. In its high vacuum mode, the RV pump is ideal for analytical instruments, electron microscopes, physics research, backing turbo pumps, TV tube pumping and leak detection applications. Configure the same pump in the high throughput mode, and it becomes suitable for mass spectrometer inlet systems, distillation, laboratory furnaces, backing vapor pumps, solvent concentration, freeze drying and other drying applications. The simple to use mode selector and accessible, three-position gas ballast control allow the pump to be reconfigured at any time, even when the pump is running. Applications Analytical instruments Centrifuges, ultra-high speed Coating Degassing/curing - oil, epoxy resin Distillation/extraction/filtration Freeze drying Furnaces Gas bottle filling/emptying Gel drying Glove boxes, ovens Laboratory bench top vacuum Leak detectors, Helium Load locks and transfer chambers Refrigeration manufacture Research and development Rotary, centirfugal evaporators Scanning electron microscopes - SEM SEM/FIB (ion beam repair) Solvent recovery Surface science instruments Turbomolecuar backing pumps Specifications Model RV8 Vacuum pump type Dual stage rotary vane Power 110V 50/60Hz 1-PH 5A or 220V 50/60Hz 1-PH 2.1A Power connection US standard 3-prong plug (NEMA 5-15P) Motor power at 50Hz 450 watts Motor power at 60Hz 550 watts Peak pumping speed 6.9 CFM at 60Hz Ultimate vacuum without gas ballast 1.5 micron/millitorr Ultimate vacuum with gas ballast 60 micron/millitorr Unit dimensions (WxDxH) 18.5 x 6.2 x 8.9" Shipping dimensions (WxDxH) 31 x 11.5 x 19" Max water vapor inlet pressure 28.5 torr (38 mbar) Max allowed pressure at outlet 0.2 bar gauge/2.8 psig Operating temperature range 54°F to 104°F (12°C to 40°C) Oil capacity Minimum 0.48 quart (0.45 L), maximum 0.8 quart (0.75 L) Oil type Ultragrade 19 Nominal rotation speed at 50/60Hz 1500/1800 rpm Noise level 48 dB(A) Inlet connection NW25/KF25 Outlet connection NW25/KF25 Unit weight 57 Lbs Shipping weight 70 Lbs Users manual Click here to download Certification CE, UL
$4,637.00 - $5,042.00
Solvent Pro Series 18/35 Gasket
Solvent Pro Series 18/35 Gasket This is a replacement Gasket for 5, 10, 30, and 50L Solvent Pro Rotary Evaporators. This gasket fits an 18mm(0.71") Inner Diameter and 35mm(1.38") Outer Diameter joint. The gasket material is made of Silicone surrounded by a PTFE Envelope.
$13.00
Agrobrite Standing LED Plant Lamp, 14w
The Agrobrite Standing Plant Lamp offers exceptional illumination and versatility! With a flexible neck and adjustable height (48" to 61") this lamp provides bright, natural light that will help plants thrive. Full spectrum light enhances the color of ornamental flowering indoor plants.Great for at work or to show off plants at home.
$86.39$76.67
Baffled Condenser - 6" x 36" with 1.5" Tri-Clamp Side Ports
Baffled Condenser - 6" x 36" with 1.5" Tri-Clamp Side Ports This 304 Stainless Steel Tri-Clamp condenser allows the user to condense hot vapors and solvent while running an extraction system or use it as a heat exchanger if needed. It features internal baffles in the system allowing for better overall heat exchange, 6" Tri-Clamp connections on each end and (2) 1.5" Tri-Clamp ports on the side to allow various connections the user may need. From end to end it is 36" in length. The inside diameter of the tubing measures 7.5mm.
$3,000.00
5L ECO Nut and Washer Flask Set
Replacement nut and washer flask set for 5L Eco Rotary Evaporator
$45.00
PTFE Valve Core for 5/10/20L for Solvent Pro Rotary Evaporator
PTFE Valve Core for 5/10/20L for Rotary Evaporator This PTFE valve core is a direct replacement for Solvent Pro Series 5L, 10L, and 20L rotary evaporators. They are used on the injection valve, drain valve, and collection flask ancillary valves. The body and seal are made of PTFE making it chemical resistant. **Please confirm you have BVV Solvent Pro Series 5L, 10L, 20L rotary evaporator before purchasing this part. If you need help identifying which model you have, please call in.**
$75.00
Toluene Lab Grade, 99.8% Purity
Toluene Lab Grade 99.8% Purity Toluene, also called methylbenzene is a colorless liquid with a flash point 40 °F. It is Less dense than water (7.2 lb / gal) and insoluble in water. Hence floats on water. This is an aromatic hydrocarbon that has a smell you would associate with paint thinners. It is a naturally occurring hydrocarbon found in crude oil. Toluene is volatile, flammable, and evaporates quickly. Toluene is the simplest member of the class toluenes consisting of a benzene core which bears a single methyl substituent. It is a non-polar solvent, Due to the presence of the methyl group, toluene is more reactive compared to benzene alone in the presence of electrophiles. Chemical Formula: C6H5CH3 Molecular Weight: 92.141 CAS Registry Number: 108-88-3 Appearance Colorless Liquid Odor: sweet, pungent, benzene-like Density 0.8623 g/ml Boiling Point: 110.60C/231.08F Solubility in water: 0.519 g/L (25 °C) GHS Pictograms: GHS Signal Word: Danger GHS Hazard Statements: H225, H304, H315, H336, H361d, H373 GHS Precautionary Statements P210, P240, P301+P310, P302+P352, P308+P313, P314, P403+P233 UN Identification Number: 1294 Proper Shipping Name: Toluene Transport Hazard Class: 3 Packing Group: II DOT Placard: What is Toluene? Toluene is a colorless, volatile, and flammable liquid aromatic hydrocarbon. It has a benzene ring substituted with a methyl group (-CH3), making its chemical formula C6H5CH3. Toluene is also known by other names such as methylbenzene or phenylmethane. It has a sweet, pungent odor and is miscible with many organic solvents but only slightly soluble in water. How Is Toluene Produced? Toluene is primarily produced as a byproduct of the petroleum refining process, specifically during the catalytic reforming of naphtha fractions. The main steps involved in the production of toluene include: Naphtha Fractionation: The process begins with the distillation of crude oil to separate it into various fractions, including naphtha. Naphtha is a mixture of hydrocarbons with carbon chain lengths typically ranging from C5 to C12. Catalytic Reforming: The naphtha fraction undergoes catalytic reforming, which is a process that involves subjecting the hydrocarbons to high temperature and pressure in the presence of a catalyst. The catalyst, often composed of platinum or platinum-rhenium on an alumina support, promotes various reactions such as dehydrogenation, isomerization, and cyclization. Aromatic Hydrocarbon Formation: During catalytic reforming, some of the naphtha molecules undergo dehydrogenation and cyclization reactions, leading to the formation of aromatic hydrocarbons, including benzene, toluene, and xylene (BTX). Toluene is specifically formed through the methylation of benzene, where a methyl group (-CH3) is added to the benzene ring. Separation and Purification: After catalytic reforming, the product stream is subjected to fractionation to separate the various components, including toluene, from other hydrocarbons. Distillation and other separation techniques are used to isolate and purify toluene from the mixture. Further Processing: The purified toluene can undergo further processing, such as hydrogenation to produce other chemicals like benzene or mixed xylenes. Toluene itself is used as a feedstock in the production of chemicals such as benzene, toluene diisocyanate (TDI), and polyurethanes. Overall, the production of toluene is closely linked to the refining of crude oil, with catalytic reforming being the primary method for its synthesis from petroleum-derived feedstocks. Other sources of toluene include coal tar and certain biomass conversion processes, although these are less common compared to petroleum-based production. What is Toluene used for? Toluene is a versatile chemical compound with numerous industrial and commercial applications. Some of the common uses of toluene include: Solvent: Toluene is primarily used as a solvent in various industries, including paint manufacturing, coatings, adhesives, and printing. It effectively dissolves other substances, making it valuable in these applications. Fuel Additive: Toluene is used as an octane booster in gasoline, improving its performance and reducing knocking in internal combustion engines. It is sometimes added to racing fuels and aviation fuels for this purpose. Production of Chemicals: Toluene serves as a precursor in the production of various chemicals, including benzene, which is used in the manufacture of plastics, synthetic fibers, and rubber. It's also used in the synthesis of toluene diisocyanate (TDI), which is a precursor to polyurethane foams. Rubber and Tire Manufacturing: Toluene is used in the production of rubber and tires as a solvent and as a component of rubber adhesives. Ink Manufacturing: Toluene is used as a solvent in the formulation of printing inks for newspapers, magazines, and packaging materials. Cleaning Products: It's used in some cleaning products, such as degreasers and spot removers, due to its excellent solvent properties. Nail Polish and Nail Polish Removers: Toluene is used as a solvent in nail polish and nail polish removers to dissolve and suspend other ingredients. Dye Production: Toluene is used in the production of dyes and as a solvent in the dyeing process for textiles and leather. Medicinal Uses: In some cases, toluene is used in pharmaceutical manufacturing processes as a solvent or as a precursor to certain drugs. These are just a few examples of the diverse range of applications for toluene. Its versatility and effectiveness as a solvent make it an essential chemical in many industries. However, Is Toluene Dangerous? Toluene poses several potential dangers to human health and the environment, especially when handled improperly or in high concentrations. Some of the key dangers associated with toluene include: Health Effects: Toluene vapor can be harmful if inhaled in high concentrations over a prolonged period. Short-term exposure to high levels of toluene vapor can cause symptoms such as headaches, dizziness, nausea, fatigue, confusion, and irritation of the eyes, nose, and throat. Long-term exposure to toluene may lead to more serious health issues, including damage to the central nervous system, liver, kidneys, and respiratory system. Flammability: Toluene is highly flammable and can form explosive mixtures with air. It has a low flash point, which means it can ignite easily in the presence of a spark, flame, or heat source. Handling toluene near open flames, hot surfaces, or other ignition sources can result in fires or explosions. Environmental Hazards: Toluene can contaminate soil, water, and air if released into the environment. It is volatile and can evaporate quickly from spills or during use, leading to air pollution. Toluene is also persistent in the environment and can bioaccumulate in aquatic organisms, potentially causing harm to ecosystems. Occupational Hazards: Workers in industries where toluene is used, such as paint manufacturing, printing, and chemical production, may be at risk of exposure to high levels of toluene vapor. Proper safety measures, including ventilation, personal protective equipment, and training on safe handling practices, are essential to minimize occupational exposure and prevent health issues. Reproductive and Developmental Effects: There is evidence to suggest that exposure to toluene may have adverse effects on reproductive health and fetal development. Pregnant women exposed to high levels of toluene may be at increased risk of miscarriage, premature birth, or birth defects in their offspring. Addiction Potential: Toluene abuse, primarily through intentional inhalation of its vapors for recreational purposes (known as "huffing" or "sniffing"), poses significant health risks, including addiction, neurological damage, and sudden death due to cardiac arrest or asphyxiation. Given these dangers, it is important to handle toluene with care, follow safety guidelines and regulations, and take appropriate precautions to minimize exposure to protect both human health and the environment. What Gaskets are recommended for Toluene? Toluene is a chemical solvent that can have compatibility issues with certain gasket materials, especially over prolonged exposure or at elevated temperatures. Some gasket materials that are generally considered compatible with toluene include: PTFE (Polytetrafluoroethylene): PTFE gaskets, commonly known as Teflon gaskets, are highly resistant to a wide range of chemicals, including toluene. They offer excellent chemical resistance and can withstand high temperatures, making them suitable for many toluene applications. Viton (Fluoroelastomer): Viton gaskets are known for their excellent chemical resistance and can often withstand exposure to toluene. They are commonly used in applications requiring resistance to fuels, oils, and solvents. Fluorocarbon (FKM): FKM gaskets are known for their exceptional chemical resistance, high temperature stability, and resistance to oils and fuels. They are often used in applications where exposure to toluene and other aggressive chemicals is expected, such as in the automotive, aerospace, and chemical processing industries. Is Toluene Polar or Nonpolar? Toluene is considered to be a nonpolar molecule.The reason for this is its symmetrical molecular structure. Toluene consists of a benzene ring (which is a hexagonal ring of carbon atoms with alternating single and double bonds) with a methyl group (-CH3) attached. The bonds between carbon and hydrogen in the methyl group are nonpolar, and the carbon-carbon bonds in the benzene ring are relatively nonpolar due to the similar electronegativities of carbon and hydrogen.Because of this symmetrical arrangement and the similar electronegativities of the atoms involved, the overall distribution of charge in the molecule is relatively uniform, resulting in a nonpolar molecule. As a nonpolar solvent, toluene is often used to dissolve nonpolar substances and is immiscible with polar solvents such as water Tolene Lab Grade SDS
$22.00 - $840.00
Upgraded TRS21 Compressor Head Complete, Stainless Fittings, Viton
Upgraded TRS21 Compressor Head Complete, Stainless Fittings, Viton Upgrade your TRS21 by purchasing a new Compressor Head with Viton O-rings for butane and propane gas compatibly and stainless steel fittings to meet FDA guidelines on handling of consumable products. This head is assembled here in the USA and is a direct replacement for any TRS21 Compressor Head.
$195.00
5L Solvent Pro Rotary Evaporator Nut and Washer Flask Set
Replacement nut and washer flask set for 5L Solvent Pro Rotary Evaporator
$45.00
Best Value Vacs 1 Gallon Flat Stainless Steel Vacuum Chamber W/GLASS LID
1 Gallon Shatter Vac Flat Stainless Steel Vacuum Chamber W/ GLASS LID (Comes with 2 Year Limited warranty) This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: High Strength Stainless Steel Chamber Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum. Specification Chamber Material 304 Stainless Steel Gasket Material Silicone Lid Material Glass Internal Dimensions (ID) 3" Tall x 10.25" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC Hose Platinum Cured Silicone Pad Black 50 Micro Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. DOES NOT APPLY TO GLASS LID VERSION ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings. Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Exludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min. For shipping info including Import/Export details visit our Shipping link at the bottom of the page.
$135.00
Bore Through 1/2" Compression Fitting x 1/2" MJIC
Bore Through 1/2" Compression Fitting x 1/2" MJIC made out of 304 stainless steel.
$12.00
True Terpenes Thin Mint Cookies Infused
True Terpenes Thin Mint Cookies Infused All sales are final. Orders can be refunded prior to fulfillment and shipping but once the order has been fulfilled and/or shipped, no refunds will be issued. Due to the hazardous nature of our product, we are unable to accept returns. (Please Note: This product has 1 week lead time) Thin Mint Cookies is yet another Girl Scout Cookies descending profile. FRAGRANCE: The peppery, sweet scent of a bakery forms the base of this profile while notes of lemon and fuel hit the nose first. EFFECT: Thin Mint Cookies is known for a peaceful yet uplifting experience. CERTIFICATES: COA | SDS | FOOD GRADE Storage Requirements Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. Store below 15℃ (60℉). Improper storage can cause terpenes to degrade. DilutionTerpenes must be diluted prior to use for flavor and effect (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With CareCan cause skin irritation, do not ingest PRIOR to dilution. TRUE GRADE™ It is our promise to you. Our isolated terpenes are triple-distilled making them the cleanest terpenes in the world. Fresh out of the bottle, undiluted, every single one of our products bests the most rigorous consumer safety standards. GMP | ISO-9001:2015 | FSSC 22000 Blended in cGMP facilities adhering to the requirements for a Quality Management System (QMS) specified by ISO 9001:2015 and FSSC 22000 standards. Analyzed Tested and passed True Grade™ safety specifications for residual solvents, pesticides and heavy metals. Stability Tested Rigorously tested with mid-grade distillate against separation, cloudiness and unacceptable levels of color change. We Qualify True Terpenes implements supply-chain control for all raw materials and is proud to provide True Terpenes’ qualification documents such as certificates, licenses and registrations to be qualified as your supplier. Undiluted We do not add PG, VG, PEG, MCT or Vitamin E Acetate to any of our products. Food Grade Manufactured in cGMP facilities using food grade ingredients. UV Protected This product is packaged in a cobalt blue, UV deterrent and food grade bottle with tamper evident seal. Made in the USA Formulated, blended, manufactured and fulfilled in the United States. Refined Isolates This product contains ultra-pure, molecularly-refined terpene isolates. Only the best.
$121.50 - $2,250.00
BVV™ Extraction RACK # 5
BVV™ Extraction RACK # 5 (Assembled units come with a 30-day warranty) Note: The unit does not come assembled - select "pre-assembled" from the drop-down menu to have the unit assembled by BVV before shipping Pipe hangers are not included There is no warranty on unassembled units Shipping Notice: If the customer orders the rack as assembled, then the item will only ship via freight and there will be additional shipping charges. Extraction Rack 5 Technical Drawing BVV™ Extraction RACK # 5 is similar to Extraction Rack #3 but with thicker vertical support beams. This rack fits the following BVV™ Extraction Systems: 10LB Mercurius 30LB Closed Loop Extraction System Specifications (Does not include height with casters) Main Base Dimensions 39" X 30" Vertical Dimensions 39" X 48"
$1,620.00 - $1,845.00
7.5CF BVV™ Neocision ETL Lab Certified Vacuum Oven
7.5CF BVV™ Neocision Certified Lab Vacuum Oven, 5 Individually Heated Shelves, LED's - 3 Year Warranty Disclaimer: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in well-ventilated areas! Introduction Our vacuum ovens are purpose-built to perform degassing / purging of light hydrocarbon solvents. Using the technique of cold boiling, the oven applies a gentle heat under reduced pressure conditions to expedite solvent degassing while simultaneously preserving color, aroma, and overall solute quality. We've applied our extensive vacuum expertise and industry experience to produce a series of ovens designed exactly for your needs: low consumption, high-throughput, and reliable operation. Performance Capabilities At Best Value Vacs, we make every effort to provide oven performance capabilities in a standardized format. We're not interested in juking our stats to make a sale. Instead, our goal is to provide quality, transparent production capabilities that meet the demands of our professional customers. Temperature Stability: ±1.0° Temperature Uniformity: within 4% of the temperature setpoint. Heat-Up Time: 20 minutes. Ultimate Vacuum: <500 µmHg / mTorr / micron. Time to Vacuum: 10 minutes to 29"Hg using our VE Series 12cfm Dual Stage Vacuum Pump. Vacuum Hold: guaranteed to lose less than 1"Hg (25.4 torr) in 24 hours. Technical Data Electrical Voltage 120V Frequency 60Hz Power 1960W Current 20A Plug IEC C13 (unit ships with detachable NEMA 5-20 cable) Internal Chamber Heating Individual direct-heat shelves Chamber Material Stainless Steel Dimensions (LxWxH) 22" x 23.25" x 25.25" Vacuum Gauge Style Glycerin-filled for accuracy and longevity Range (units) -30 to 0 (inHg) / -1 to 0 (bar) Shelving Ships With 5 Heated Shelves Shelf Dimensions (LxW) 21.5" x 21.5" Shelf Capacity 462 in2 Total Shelf Capacity 2311 in2 / 16.1 ft2 Safety Seal Silicone on Tempered Glass Window Dimensions (LxH) 20.25" x 23.75" Lights 4 strips of LEDs provide a clear, bright view of the interior Handle No plastic, all metal parts for lifetime durability Exterior Dimensions (LxWxH) 35" x 33" x 34.5" Weight 430 lbs Support Locking Casters Safety Electrical Built-in, resettable, overcurrent circuit breaker Thermal Automatic overtemperature shutoff Compliance CE CE Listing Recognized ISO ISO 9001:2015 ETL Certified Conforms to ANSI/UL STD.61010-1, 61010-2-010 -- Certified to CAN/CSA STD. C22.2 NO.61010-1, 61010-2-010 Connections Vacuum Inlet KF25 / NW25, quarter-turn valve Purge Inlet 5/16" Barbed, 10-turn valve Atmospheric Release Quick-release dial Contains Ships With KF25 x 1/4" JIC Flare with 1/4" vacuum hose User Manual Included Vacuum Pump Sold Separately. Warranty 3 Years Capacity and Throughput Planning Oven capacity requirements vary widely by the producer. We wanted to create a method to assist in determining the best oven match for your operation, based on a few of the parameters of your extraction and of your desired purge. We based this formula on an expected extraction yield of 25%, with an extract-density of 1 g/in2. Using the following variables, this formula is designed to provide an estimate of your required shelving capacity: Size = Extraction Batch Size (lbs) Number = Runs per 24h Period Purge = Your desired purging duration (hours) Area Required (ft2) = [(Size) * (Number) * (Purge+1)] / 122 Area Required (in2) = (Size) * (Number) * (Purge+1) * 1.18 Note: This item is a freight ship item and will ship Via UPS Ground Freight. Expedited freight can only be calculated by calling customer service 331-281-0154. All orders with expedited freight through the website will not be honored and will need to be re-quoted. A valid Phone Number IS REQUIRED to ship, Otherwise UPS freight Cannot Contact you for a delivery setup window. Freight Time is 2-5 Days. West Coast 5 Days, Midwest 2 days, East Coast 3-4 days.
$8,100.00
Minor Repair Kit for Welch 1400 DuoSeal
Minor Repair Kit for Welch 1400 DuoSeal This minor repair kit enables refurbishment of DuoSeal pump model 1400. Includes gaskets, seals, valves, o-rings, springs, and mechanical shaft seal. All parts are Welch Original equipment with enhanced chemical resistance. Manufactured to design specifications for top pump durability and performance.
$298.00
Dry Ice Condenser for 2L Electric Lift Rotary Evaporator
Dry Ice Condenser for 2L Best Value Electric Lift Rotary Evaporators. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$375.00
1L Standard Distillation Turnkey Setup
1L Standard Distillation Turnkey Setup The Standard Distillation Turnkey Setup includes all the components necessary to successfully perform distillation at an entry level price point. The Standard Turnkey Setup Includes: 1L Distillation Kit 1/4" Flare x 1/4" Barb Adapter BVV™ 5L Heated Circulator BVV™ V9D 9CFM Two Stage Vacuum Pump Distillation Quick Start Guide This guide gives basic quick start instructions for distillation systems. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs, Before beginning distillation, ensure the following steps have been taken: Vacuum Pump is in good working order. Pump should be run against dry load to allow internals to warm up. Oil should be clear. Cloudy or dark oil should be changed. All glass components are in good working order and ready to be assembled A winterization and degassing procedure has been done to prepare oil for distillation Once all three of these steps have been completed, you are ready to begin distilling. Begin by placing stir bar in boiling flask and then load your material. This should be done using a funnel. A small amount of alcohol in the oil will give it a thinner consistency making it easier to transfer. Assemble all glassware and ensure each joint is properly greased. Do not use too much, as the vacuum pressure might pull some grease into the system. To ensure a full seal, spread grease in a circular motion by rotating glassware Attach circulator to condenser and set temperature to 50C. Allow circulator to reach temperature before beginning distillation. Connect vacuum pump to manifold. The manifold will allow you to isolate each individual component as well as let atmosphere into and out of the system. Connect receiving cow to cold trap. Connect cold trap to manifold. Connect vacuum gauge to manifold. At this point, ensure all connections are correct. Also ensure receiving cow is positioned to collect the first fraction in the far-left receiving flask. Circulator should be at its set temperature. Turn on vacuum pump to begin process. Turn on heat and set to 60C. Vacuum pump will begin to pull down and temperature will begin to rise. Watch the gauge to monitor vacuum pressure and stability. Start stir slower and increase speed with temperature. Once you are close to 60C, increase the temperature 20 degrees. Continue to raise the heat incrementally in 20-degree steps, increasing the set temperature as you near your set point. Increase temperatures incrementally until you reach 220C. You will see your first fraction somewhere between 180C and 190C or slightly before. This is the “heads” fraction. You will move to your second fraction when you see an increased reaction in the head, a slight color change toward golden, as well as a thickening of distillate. When this fraction hits, allow the distillate to “self-clean” the head for a minute or two then, rotate the cow to the middle receiving flask. Collect your “main body” fraction. You will see temps between 190-220C during this fraction. Continue to increase stirring speed as necessary. Reaction in the head may vary but it should never stop. As fluid level in the boiling flask decreases, increase stir speed. The final “tails” fraction is a mixture of the first and second fractions and should be saved for re-distillation later. Ideally, you want to turn the cow to the final flask before the tails fraction hits. The “tails” fraction has an obvious color change and will be darker than the “main body” fraction. You will see temps between 200-250C during this fraction. As fluid level in the boiling flask decreases even more, set stirring RPM higher (1000+ RPM). You may need to compensate with a bit more heat to finish of the final fraction as well. Once process is complete, stop heat, stop stir, and stop vacuum. Let atmosphere into the system. Be sure to properly store your distillate as exposure to air and light can cause oxidation. ***Note: This entire setup will ship via motor freight.*** *Notice to Customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. BVV™ is not responsible for the failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail, which can cause bodily harm or damage to the surrounding area.
$2,100.00 - $2,350.00
BVV™ 8 Ton 304SS Puck Press
BVV™ 8 Ton 304SS Puck Press This BVV™ 8 Ton 304SS Puck Press allows users to compress material into an easily manageable puck. Specifications: 304 Stainless Steel Components (Excludes Jack) External Dimensions - 7-1/8" x 7-1/8" x 14" Internal Puck Mold Diameter - 3.75" Mold Height - 3-1/4" Weight - 34LBS
$315.00
BVV 280L Centrifuge Bags
This nylon bag is designed to fit in our BVV brand centrifuges to contain material and be easily swappable after runs to speed up processing times. These bags come with 2 zippers and come in 1, 10, 50, 100, and 200 micron filtration levels. For use with 280L Centrifuges Appx. Size : 39.25" Diameter x 14" Height Specifications SKU Appx. Diameter In. Appx. Height in. CFB-45L-XXX 17.5" 11.75" CFB-160L-XXX 32.25" 13" CFB-280L-XXX 39.25" 14" CFB-475L-XXX 47.25" 16.75"
$206.00 - $398.00
You have seen 1008 out of 2683 products