All products
Edwards NXDS10iC 7.5 Cfm Chemical-Resistant Dry Scroll Pump
Edwards NXDS10iC 7.5 Cfm Chemical-Resistant Dry Scroll Pump Dry Scroll Pumps Dry scroll vacuum pumps are positive displacement pumps that use two spiral-shaped scrolls, one fixed and one orbiting, to trap and compress gas molecules. They are oil-free, low maintenance pumps that are commonly used for clean vacuum applications. Since they do not rely on oil for sealing and lubrication, they eliminate the risk of oil contamination and leakage, making them an environmentally-friendly choice. We in Edwards are driving scroll technologies to its best and we are committed to offer the most sustainable solution now and in the future. nXDSi Scroll Pumps Edwards nXDS is the great new shape of dry vacuum pumping. The nXDS has taken scroll vacuum technology to the next level. Improved performance, exceptional pumping capability, quiet operation and extended service intervals make nXDS the ultimate dry choice. The range covers pumping speeds from 6 to 20 m3/h. nXDS10i The nXDS10i same as the nXDS15i are our key products offering a small dry pump solution for most Scientific Applications. Standard variant suitable for a large variety of applications; R-variant with blanked gas ballast and C-variant being corrosion resistant. nXDS10iR - 100-127/200-240V 1Ph 50/60Hz The nXDS10iR has the gas ballast blanked off so it cannot be accidently opened. These variants are available for specialist applications such as gas recirculation, rare gas pumping and recovery or other applications where the dilution of the pumped gas is undesirable, or where sealing is integral to minimising potential gas loss. Features and Benefits Quiet operation - Better working environment Hermetically sealed for a lubricant-free vacuum environment - Contamination free process and no oil to dispose of Low power consumption - Low cost of ownership Intelligent and easy to use controls - Flexibility of operation Superior vapour handling - Wider range of applications Long service intervals - Maximised up-time Specifications Technical Data Power requirements 100-127V~10A or 200-240V~6A, 50/60 Hz, 280 watts Nominal rotational speed 1800 rpm Displacement 12.7 m3h-1/ 7.5 ft3min-1 Peak pumping speed 11.4 m3h-1/ 6.7 ft3min-1 Ultimate vacuum (total pressure) 0.007 mbar / 0.005 Torr / 5 micron Minimum standby rotational speed 1200 rpm Speed control resolution (% of full speed) 1% Maximum inlet pressure for water vapour 35 mbar Maximum water vapour pumping rate 145 gh-1 Maximum continuous inlet pressure 200 mbar Power connector 1-ph IEC EN60320 C13 Recommended fuse 10A, 250Vac rms Unit/shipping weight 57 Lb / 60 Lb Unit/shipping dimensions 16.5x10x12" / 20.5x13x14" (DxWxH) Inlet flange NW25 (KF25) Exhaust flange NW25 (KF25) Noise level 52 dB(A) Vibration at inlet flange < 4.5 mms-1 (rms) Leak tightness (static) < 1x10-6mbar ls-1 Operating temperature range 10 to 40 C / 41 to 104 F Edwards part number A73602983 Certification CE, UL
$10,716.00
Dual Diaphragm Rebuild Kit For ULVAC DTC-41 1.6 Cfm Pumps
Dual Diaphragm Rebuild Kit For ULVAC DTC-41 1.6 Cfm Pumps Overview Dual-diaphragm rebuild kit for DTC-41 1.6 CFM dual-stage chemical duty diaphragm pumps. Standard package Part description Quantity Part image Diaphragm NT 2 pc Suction/discharge Valve A 3 pc Suction/discharge Valve B 2 pc O-Ring (S-28) 4 pc O-Ring (P-10A) 2 pc O-Ring (AS568-110) 4 pc Bill of Material 1 pc
$425.00
Clear Standard 2 Tray Set
Clear Standard 2 Tray Set This is the same 2 trays that your King Kone originally comes with, out the box. The bottom tray packs the 84mm cones also known as the 1 ¼ size and the top thinner tray in supplement with the bottom tray can pack the size 98mm and the 109 King sized cones. Some people like to purchase extra sets of these trays so that while one is in use on the machine, the additional tray set could be loaded with cones for the next run. Having an extra set increases production rates and assures that every minute is being used towards increasing results.
$375.00
SCILOGEX SCI280-Pro, Circular LED Digital Hotplate-Stirrer, ceramic plate, 110V, 50/60Hz, US Plug
SCILOGEX SCI280-Pro Circular-top LED Digital Hotplate Stirrer 280ºC/1500rpm Max Product Description The SCI280 hotplate-stirrer is a very economically priced LED digital hotplate-stirrer ideal for handling small volume task on daily application, as a low temperature magnetic stirrer with max. temperature at 280°C. This compact unit can be used as a hotplate, stirrer or combination. Product Features Heat only, stir only or heat and stir together functions Digital temperature control with max. temperature up to 280°C Digital speed control with max. speed up to 1500rpm, with new brushless motor Stainless steel work plate with ceramic coating provides good chemical resistant performance and easy cleaning LED display shows temperature and speed External temperature control is possible by connecting the temperature sensor(PT1000) with an accuracy at ±0.5°C The “HOT” warning will flash when the work plate temperature is above 50°C even if the hotplate is turned off Accessory reaction blocks for flasks and vessels available Electronic speed control for constant speed even during changes in load Comes with a free 50mm L x 5mm Dia. Magnetic Stir bar cTUVus approved for UL and CSA 2 Year Warranty Product Specifications Work plate dimension[W x D] φ135mm(5 inch) Work plate material stainless steel cover with ceramic Motor type Brushless DC motor Motor input power 5W Motor output power 3W Power 515W Heating output 500W Voltage 100-120V 60Hz Stirring positions 1 Max. stirring quantity 3L Max. magnetic bar[length] 50mm Speed range 200-1500rpm Speed display LED Temperature display LED Speed display resolution ±1rpm Heating temperature range Room Temp.-280°C, increment 1°C Temperature control accuracy ±1°C(100°C) Overheating protection 320°C Temperature display accuracy ±1°C External temperature sensor PT1000 (accuracy ±0.5°C) "Hot" warning 50°C Protection class IP21 Dimension[WxDxH] 150×260×80mm Weight 1.8kg Permissible ambient temperature and humidity 5-40°C, 80%RH Additional Resources and Information Downloadable PDFs SCI280-Pro Manual Hotplates & Stirrers Brochure Hotplate & Stirrers Accessories
$300.00 - $375.00
SCILOGEX SCI6-Pro LCD Digital 5.5 x 5.5 in. Magnetic Stirrer, ceramic plate, 110-240V, 50/60Hz US Plug
SCILOGEX SCI6-Pro 5.5 x 5.5 in. LCD Digital Magnetic Stirrer, 200-1500rpm SCILOGEX SCI6-Pro 5.5 x 5.5 in. LCD Digital Magnetic Stirrer, 110-240V, 50/60 Hz. SCILOGEX SCIS6-Pro 5.5 x 5.5 in. LCD Digital Magnetic Stirrer Features: Easy to read backlit LCD display, with independent heat and stir display Ceramic plate for chemical resistance and easy clean Brushless DC motor is maintenance free Aluminum cover with ceramic work plate, allows for immediate heat transfer External temperature control is possible with temperature sensor PT1000 Electronic speed control for constant speed even during changes in load Comes with a free 50mm L x 5mm Dia. Magnetic Stir bar Max. stirring quantity of H2O at 5L Digital speed control with max. speed up to 1500rpm cTUVus approved for UL and CSA 2 Year Warranty The new MS6-Pro magnetic stirrer is a very economically priced LCD digital stirrer. Digital Magnetic Stirrer Specifications: Work plate dimensions (WXD) 140x140mm Work plate material Aluminum cover with ceramic coating Motor type Brushless DC motor Motor input power 2.4W Motor output power 1.8W Power 10W Voltage 100-240V, 50/60Hz Stirring positions 1 Max. stirring quantity[H2O] 5L Max. magnetic bar[length] 50mm Speed range 200-1500rpm Speed display LCD Protection class IP21 Dimension[WxDxH] 320x180×108mm Weight 2.2kg Permissible ambient temperature and humidity 5-40°C, 80%RH Control accuracy of sensor ±20rpm Additional Resources and Information Downloadable PDFs SCILOGEX Hotplate-Stirrers brochure SCILOGEX SCI6-Pro manual
$310.00
SCILOGEX SCI-Spin Stirrer, 100-240V, 50/60Hz, US Plug
SCILOGEX SCI-Spin Stirrer, 15-1500rpm SCILOGEX SCI-Spin Stirrer, 100-240V, 50/60Hz, US plug Product Features A wide range of speed from 15-1000rpm Automatic reverse rotation for excellent stirring Protection class (IP65) PET top provides excellent chemical resistance Slip-proof and stable Ultra silence and vibration-free Multi-voltage cTUVus approved for UL and CSA 2 YEAR WARRANTY The Scilogex SCI-Spin Stirrer is an ultra-flat compact stirrer ideal for stirring applications. Its space saving design minimizes bench space and portable due to its light weight. With excellent stirring functionality, the compact shape of FlatSpin takes less bench space and makes storage easier. Product Specifications Work plate dimension Φ90mm Work plate material PET Motor type Motorless Motor output power 3W Power 5W Voltage 100-120/200-240V,50/60Hz Stirring positions 1 Max. stirring quantity[H2O] 0.8L Max. magnetic bar[length] 40mm Speed range 15-1500rpm Speed display button Protection class IP65 Dimension[WxDxH] 175x120x15mm Weight 0.3kg Permissible ambient temperature and humidity 5-40°C, 80%RH Additional Resources and Information Downloadable PDFs SCI-Spin Stirrer Manual Hotplate-Stirrers Brochure SCILOGEX SCI-Spin Magnetic Stirrer.mp4 from SCILOGEX on Vimeo.
$170.00
SCILOGEX SCI20-Pro Overhead LCD Digital Stirrer, with stand and s/steel cross srirrer, 20L Capacity, 100-220V 50/60Hz, US Plug
SCILOGEX SCI20-Pro Overhead LCD Digital Stirrer, with stand and s/steel cross srirrer, 20L Capacity, 100-220V 50/60Hz, US Plug SCILOGEX SCI20-Pro Overhead LCD Digital Stirrer, 20L Capacity, 100-220V 50/60Hz, US Plug. Includes Stand (Part# 18900131) and Steel Cross-stirrer (Part# 18900071) Product Features Accurate microprocessor stirring speed control guarantees speed precision Anti-spill microprocessor control slow start up prevents accidental spillage and splashing RS232 provides PC control and data transmission with free software A through-shaft design allows for easy adjustment of the impeller positions Brushless DC motor for long life and maintenance free Provides constant speed even with changes in viscosities of the samples LCD display for precise monitoring of set and actual speeds, a wide range of speed from 50 to 2200rpm with control accuracy of ±3rpm. Set value and actual value can be displayed for real-time monitoring of torque and speed Over torque protection automatically stops the motor Torque trend display for real-time information on viscosity changes Pass through stirrer rods accepted Keyless chuck PC software control via RS232 interface, for control and documenting all measured values via PC. Download software here cTUVus approved for UL and CSA 2 YEAR WARRANTY SCILOGEX Overhead Stirrers can accomplish the most demanding tasks and provide high safety and increased performance. They are widely used in chemical synthesis, pharmaceutical synthesis, physical and chemical analysis, petrochemical industries, etc. Product Specification Maximum stirring capacity 20 Liters Maximum torque 40Ncm Viscosity maximum 10000mPas Speed range 50-2200rpm Speed display accuracy ± 3rpm Speed display resolution ± 1rpm Chuck diameter range 0.5-10mm Dimensions 3.3W x 8.7H x 7.3D inches (83W x 220H x 186D mm) Motor rating input 60W Motor rating output 50W Weight 5.5lbs Motor type brushless DC motor Voltage/Power 100-220V, 50/60 Hz/ 70W Speed/Torque display LCD Overload protection display LED lights Protection class IP21 Data connector RS232 Permissible ambient temperature and humidity 5-40°C, 80%RH Additional Resources and Information Downloadable PDFs SCI20-Pro Manual Scilogex OverheadStirrers Brochure Scilogex OverheadStirrers Software SCILOGEX SCI20/40-Pro LCD Digital Overhead Stirrer.mp4 from SCILOGEX on Vimeo.
$1,112.00
True Terpenes Sugar Cookie
True Terpenes Sugar Cookie Get your holiday baking off to a sweet start with Sugar Cookie terpene strain. Notes of soft sugar cookies fresh from the oven lead this dessert strain profile. We then added a swirl of blueberry frosting, a handful of juicy berries, and a hint of soft lavender florals to the mix for a tempting take on the sweet, fruity cross between Crystal Gayle, Blue Hawaiian, and Sensi Star. Recommended Use and Restrictions on Use This product is concentrated and should not be used undiluted. Based on your use of this product, determine appropriate warnings and directions for your products and applications; also determine safety standards and conduct testing. Avoid contact between this undiluted product and skin, eyes, wood surfaces, and fabrics. Keep this undiluted product away from children and pets. Discontinue use if any adverse reaction occurs. This product has not been evaluated for safe use in e-cigarettes, or in any nicotine-containing or smoking-cessation product. Not for use with tobacco or nicotine. This product is not intended for use by those who are pregnant, nursing, or by those with serious health conditions including but not limited to high blood pressure and diabetes. This product is not intended to diagnose, treat, cure or prevent any disease. Store in original container, sealed tightly, in a cool, dry place away from sunlight or heat sources. This product should not be used beyond its stated expiry date. Products made with this item should be tested to determine suitable shelf life. WARNING True Terpenes cannot anticipate all conditions under which this information and this product, or the products of other manufacturers in combination with this product, may be used. It is the user’s responsibility to stay current with respect to applicable laws and regulatory investigations and findings, and to ensure safe conditions for use, handling, storage and disposal of the product. The user assumes all liability for loss, injury, damage or expense due to unauthorized or improper use, and True Terpenes disclaims all such liability. The information in this sheet was written based on knowledge and experience currently available. To date, True Terpenes has not received any evidence confirming that this product has caused any adverse health consequences. The above information relates only to this product and not to its use in combination with any other material or any particular process, and is designed only as guidance for the handling, use, processing, storage, transportation, and disposal. It should not be considered as a guarantee or quality specification. True Terpenes has performed no testing on this product in e-cig/vaping applications. Applying heat to a compound or mixture of compounds may promote new product formation by thermal degradation. New products could include harmful or potentially harmful compounds. It is the sole responsibility of the individual(s) purchasing this product to assess its safety in the final application. The above information is based on data provided by and collected from recognized sources such as distributors, manufacturers, and technical groups and is considered to be accurate to the best of True Terpenes’ knowledge, based upon current information as of the publish date of this document. It is the responsibility of the user to review all safety information about this product and determine its safety and suitability in their own uses, processes, and operations. Appropriate warnings and safe handling procedures should be provided to all handlers and users of this product, taking into account the intended use and the specific conditions and factors relating to such use in accordance with all applicable laws and regulations. COA & Ingredient Disclaimer This Certificate of Analysis contains specifications and results provided by contract laboratories external to True Terpenes. This document does not relieve the purchaser from conducting their own tests in order to verify the suitability of this product for its application and to comply with all relevant legal requirements for any goods into which this product is incorporated. Botanically derived and/or synthetic compounds found in this product may contain trace compounds which can potentially result in a slight variance between lots. The limits in this Certificate of Analysis may not be inclusive of all compound regulations in your region. Shelf Life Disclaimer Unless otherwise stated on the label, COA, or SDS, the intended use for this product is one year from the date of purchase or listed manufacturing date. It is crucial to observe product label directions and store terpenes properly to maintain product integrity. Terpenes are volatile organic compounds (VOCs) and may degrade over time. Customers may contact our quality department at info@trueterpenes.com to obtain further information regarding a specific production lot. Nutritional Statement True Terpenes certifies that, to the best of our knowledge, the product listed above does not contribute to the nutritional value of flavors due to their extremely low usage levels and therefore falls under the nutritional labeling exemption defined in Section 101.9(a) and (j) of Title 21 of the Code of Federal Regulations. Testimonial Disclaimer In accordance with the FTC guidelines concerning the use of endorsements and testimonials in advertising, please be aware of the following: Testimonials appearing on this website are received in various forms via a variety of submission methods. To the best of True Terpenes’ knowledge, the testimonials reflect the real-life experiences of individuals who used our products and/or services. However, individual results may vary. We do not claim, nor should the reader assume, that any individual experience recounted is typical or representative of what any other consumer might experience. Testimonials are not necessarily representative of what anyone else using our products and/or services may experience. The testimonials displayed are given verbatim except for grammatical or typing error corrections. Some testimonials may have been edited for clarity, or shortened in cases where the original testimonial included extraneous information of no relevance to the general public. True Terpenes is not responsible for the opinions or comments posted on this website, and does not necessarily share the opinions, views, or commentary of postings on this website. All opinions expressed are strictly the views of the poster or reviewer. Testimonials on this website are not intended, nor should they be construed, as claims that the products or services mentioned can be used to diagnose, treat, cure, mitigate or prevent any disease. To the contrary, our products are not intended to diagnose, treat, cure, or prevent any disease. No testimonial has been clinically proven or evaluated, and no health, functional or structural claims whatsoever were made and no statements on this website have been evaluated by the FDA or any other regulatory agencies. Intended Purchasers; Dilution Before Use The products offered on this website are intended for purchase by lawfully operating businesses. These products are not intended for purchase by consumers. Each of these products should be carefully diluted prior to use. COA Sugar Cookie COA Lot# 23081108 Sugar Cookie COA Lot# 23080917 Sugar Cookie COA Lot# 23080918 Sugar Cookie COA Lot# 23081608 Sugar Cookie COA Lot# 23081609 SDS Sugar Cookie SDS PDS Sugar Cookie PDS Company Certificates ISO 9001:2015 GMP Certification FSSC 22000 Food Safety True Grade Quality TRUE GRADE™ It is our promise to you. Our isolated terpenes are triple-distilled making them the cleanest terpenes in the world. Fresh out of the bottle, undiluted, every single one of our products bests the most rigorous consumer safety standards. GMP | ISO-9001:2015 | FSSC 22000 Blended in cGMP facilities adhering to the requirements for a Quality Management System (QMS) specified by ISO 9001:2015 and FSSC 22000 standards. Analyzed Tested and passed True Grade™ safety specifications for residual solvents, pesticides and heavy metals. Stability Tested Rigorously tested with mid-grade distillate against separation, cloudiness and unacceptable levels of color change. We Qualify True Terpenes implements supply-chain control for all raw materials and is proud to provide True Terpenes’ qualification documents such as certificates, licenses and registrations to be qualified as your supplier. Undiluted We do not add PG, VG, PEG, MCT or Vitamin E Acetate to any of our products. Food Grade Manufactured in cGMP facilities using food grade ingredients. UV Protected This product is packaged in a cobalt blue, UV deterrent and food grade bottle with tamper evident seal. Made in the USA Formulated, blended, manufactured and fulfilled in the United States. Ships Worldwide True Terpenes ships its botanical aromatic blends worldwide. Refined Isolates This product contains ultra-pure, molecularly-refined terpene isolates. Only the best. Storage RequirementsKeep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store in a cool dry place. Improper storage can cause terpenes to degrade. DilutionTerpene Strain & Flavor-Infused Strain Profiles, Effects-Based Terpene Profiles & Terpene Flavors:The Terpene products above must be diluted prior to use. (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Viscosity Extract Modifier:The Terpene product above must be diluted prior to use. (1-3% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With CareCan cause skin irritation, do not use PRIOR to dilution.
$121.50 - $2,250.00
3000mL Single Neck RBF, 35/25 Socket Joint
3000mL Single Neck RBF, 35/25 Socket Joint Round bottom, HEAVY WALL single short neck flask with a spherical socket joint. Flasks having a 35/20 socket joint are used as replacements for the collection flask on rotary evaporators.
$249.00
1000mL Single Neck RBF, 35/25 Socket Joint
1000mL Single Neck RBF, 35/25 Socket Joint Round bottom, HEAVY WALL single short neck flask with a spherical socket joint. Flasks having a 35/20 socket joint are used as replacements for the collection flask on rotary evaporators.
$79.00
Extend Protection Plan
Extend Protection Plan
$54.99 - $99.99
The Press Club 1.25" x 4" ROSIN BAGS
1.25" x 4" Rosin Bags The Press Club brings science to the art of rosin pressing. The Press Club Prides themselves in making the toughest and strongest rosin bags on the market. After years of research and lab testing, their rosin bags are now made with our proprietary pink stitch and come with a ZERO BLOWOUT GUARANTEE™. If you ever get one, They will replace the bag. It's that simple. Available in 25, 37, 50, 75, 90, 120, 160 and 220 micron. 1.25” x 4” Inch 10-Pack Pre-Flipped Inside-Out 100% Food-Grade Nylon Solvent & Boil Resistant High Pressure Resistance (Over 20 Tons) High Heat Resistance (Up To 375° F) Reusable Over 5x (Simply Wash With Alcohol) Covered By The Press Club’s Zero Blowout Guarantee Satisfaction Guarantee & 365-Day Return Policy Made In USA General Micron Guideline: Dry Sift & Bubble (5, 10, 15, 25, 37, 50) | Flower (75, 90, 120, 160, 220)
$12.95
BVV Bead Bath
BVV Bead Bath Introducing the BVV's Bead Bath - A cost-effective Bead Bath for Precise and Contamination-Free Laboratory needs. The Bead Bath is a cost-effective bead bath that allows for precise temperature application to warm your extracts, distillates, and isolates faster than a traditional hot plate eliminating water contamination. Unlike traditional water baths, bead baths replace water with reusable metallic beads, eliminating the risk of experimental contamination and ensuring accurate results. With the Bead Bath, you can say goodbye to high electricity consumption and frequent cleanup. The bead bath's efficient design minimizes power usage, as the beads do not evaporate, and require less maintenance, saving you time and resources. Experience rapid start-up times and uniform heating with the Bead Bath's surround heating feature. This cutting-edge technology guarantees even temperature distribution, preventing hotspots and ensuring consistent and reliable outcomes for your samples. Safety is our top priority, and the Bead Bath is no exception. Equipped with over-temperature protection, this bead bath maintains safe and stable conditions for your valuable samples throughout the entire experiment. Discover the benefits of the BVV Bead bath and revolutionize your laboratory work with contamination-free, precise, and efficient temperature control. Join researchers and professionals worldwide in experiencing the power of the #1 bead bath ranked on Google. Upgrade your experiments with the BVV's Bead Bath.* Does not include Beads*
$130.00 - $240.00
1/2" Insulon Vacuum Jacketed Hose, Low Pressure
1/2" Insulon Vacuum Jacketed Hose, Low Pressure Technical Specifications: Hose Size 1/2” ID DN (ISO 10380) 12 Product Category LP (Low Pressure) Inner Hose ID 0.472” Tube Stub OD 0.500” Tube Stub Thickness 0.035” Outer Hose OD 1.27” Static Bend Radius 3.33” Dynamic Bend Radius 10.24” Lengths 2 – 20’ Operating Temperature -270°C to 900°C (-454°F to 1652°F) Material 316L stainless steel Maximum Allowable Working Pressure (MAWP) by Temperature: Product Category Hose Size Max Temperature (C) Max Temperature (F) MAWP (PSI) Low Pressure (LP) 1/2" ID 21 70 72 Low Pressure (LP) 1/2" ID 66 150 67 Low Pressure (LP) 1/2" ID 93 200 64 Low Pressure (LP) 1/2" ID 121 250 62 Low Pressure (LP) 1/2" ID 149 300 60 Low Pressure (LP) 1/2" ID 166 330 58 Low Pressure (LP) 1/2" ID 204 400 56 Low Pressure (LP) 1/2" ID 232 450 56 Low Pressure (LP) 1/2" ID 260 500 55 Low Pressure (LP) 1/2" ID 316 600 55 Low Pressure (LP) 1/2" ID 371 700 55 Low Pressure (LP) 1/2" ID 427 800 54 Low Pressure (LP) 1/2" ID 482 900 53 Low Pressure (LP) 1/2" ID 538 1000 53 Low Pressure (LP) 1/2" ID 593 1100 48 Low Pressure (LP) 1/2" ID 649 1200 44 Low Pressure (LP) 1/2" ID 704 1300 40 Low Pressure (LP) 1/2" ID 760 1400 35 Low Pressure (LP) 1/2" ID 816 1500 28 Low Pressure (LP) 1/2" ID 899 1650 18
$260.00 - $1,172.00
Micro-Cap Filters
ErtelAlsop Micro-Cap Filters 1 Micron Grade M-503P Diatomaceous Earth Micro-Cap 1 Micron Grade MC-55CP Carbon Filled Micro-cap With single-use technology on the rise, our new ErtelAlsop MicroCap Laboratory Cabinet has been created to simplify filtration and separation trials for research and development, as well as, process development laboratories. This attractive and well organized Cabinet easily stores the filters you require. The MicroCap™ suite of single-use capsules provide a uniquely flexible line of disposable depth filter products designed for optimizing and developing processes during scale-up and scale-down studies. The MicroCap 22 capsule enables quick and efficient determination of appropriate media grades in providing the best filtration performance as well as required filtration area to meet process volumes. Each MicroCap Laboratory Cabinet is supplied with forty-eight MicroCap 22 capsules in twelve different grades ranging from a nominal 15 micron to 0.2 micron. All supplied capsules contain 22.5 cm2 (3.48 in2) of filtration area per capsule. These easy to use capsules allow users to test a comprehensive range of depth filter media and efficiently determine the right solution for their process needs. Applications MicroCap capsules are designed for small volume processing of: Primary separations/prefiltration Secondary clarification Cell culture harvest Cell culture clarification DNA removal Endotoxin reduction Host Cell Protien (HCP) reduction Protein aggregate removal Decolorization Performance The MicroCap Laboratory Cabinet incorporates ErtelAlsop’s MicroCap capsules each containing our high performance XL Series, and select MicroMedia series grades of depth filter media to provide the optimum balance of dirt holding capacity and throughput. Containing a high performance grade of diatomaceous earth filter aid, coupled with a strong positive zeta potential, ErtelAlsop’s XL media capsules provide superior contaminant retention. The XL Series of depth filter media exhibits 2-5 times the throughput of competitive media while maintaining equivalent or better product clarity. Reliability As with all ErtelAlsop depth filter products the MicroCap capsules provide performance consistency and lot to lot traceability all in an easy-to-use format. All MicroCap capsules are batch tested in order to meet all quality requirements and meet all applicable USP requirements including the Class VI Plastics. Scalability The MicroCap series of single-use capsules contain six easily scalable sizes of capsules. Additionally each of these capsules readily scale to ErtelAlsop’s 12” and 16” diameter lenticular depth filter modules.
$10.00 - $15.00
4" Sweating Baskets
4" Sweating Baskets Sweat the terpene sauce o of your crystallized compounds or dry out wet sugars using a tri-clamp spool. Specifications: 304 Stainless Steel 25 Micron W: 4” H: 5”
$17.00 - $55.00
ChemTek L550 Centrifuge
ChemTek L550 Centrifuge L550 centrifuges provide excellent performance and easy operation in a compact design that saves valuable time and laboratory space. Specifications: Power Supply:110V 50/60Hz Max Speed:4000 RPM Max RCF:3040xg Max Capacity:4x500ml Time Setting Range:1min - 99min Speed Accuracy:± 10r/min Noise: ≤65dB Power Consumption:750W Net Weight:115lbs Comes with: (16) 50ml Tube (4) Regular Mouth Basket (4) Regular Mouth Stainless Jar Lid/Band (4) Four 50ml Tube Holder Insert (4) Regular Mouth Jar Spacer Insert (1) 50-pack 5”x 7” Double Stitched Fuge Bags (1) Terp SqueeGee (1) 100-Pack of Large Diamond Grip Gloves ChemTek L550 Centrifuge User Manual ChemTek L550 Centrifuge SDS
$4,700.00
Chromatography Column
Chromatography Column Chromatography Column This 3”x24” chromatography column features an internal volume of 2.7L. It’s commonly used for removing pesticides, separating components, and cleaning different chemical compounds. Additional consumables or accessories will be needed depending on the application. Capacity can be increased with an additional reservoir adapted to the top 45/50 Rodaviss joint. Rodaviss joints are great for disconnecting any stubborn joints. Light grease is still recommended when assembling joints. Light grease is still recommended when assembling joints. Features: Needle control valve 3”x24” column with 2.7L capacity 45/50 Rodaviss joint Sintered disk Stop cock For additional information or questions regarding this kit, accessories, and consumables contact our customer support line. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$350.00
Chemical-Resistant Viton® Fluoroelastomer O-Ring
Chemical-Resistant Viton® Fluoroelastomer O-Ring 1/16 Fractional Width, Dash Number 006
$0.95
Caster Wheels for Reactors
Heavy duty replacement wheels to be used on 50L, 150L, and 300L BVV Stainless Steel Reactors.
$30.00
4" Tri-Clamp U-Bend with 2" Side Port
This 4" Tri-Clamp U-Bend is 14" in length from center to center of the 4" ports. There is a 2" port in the middle that is useful to mount sensors, gauges, or sight glasses. The material of this part is 304 Stainless steel.
$275.00
Part A 2" Stubby Metric Cam Lock Adaptor
Part A 2" Stubby Metric Cam Lock Adaptor This adapter converts 2" (50mm) male buttress pipe threads to a 2" male camlock. The adapter incorporates female buttress threads on one end and a male Camlock (also known as a quick-disconnect or QD) on the other for connecting pipes and valves with different ends. Made of tough polypropylene (PP), this adapter also incorporates an ethylene propylene diene monomer (EPDM) gasket for a leak-tight connection. Shallow profile ensures valve does not protrude past IBC tote cage. Key benefits: Converts 2" male buttress pipe thread to a 2" male quick-disconnect 2" long profile does not protrude past IBC cage during transport Combo camlock/NPT end allows use of a shallow NPT cap Made of PP EPDM gasket ensures a secure seal Suitable for use in a wide variety of liquid handling applications Proudly Made in the USA Material: Polypropylene (PP) is a tough plastic that has good chemical resistance. PP is translucent in its natural state but can have a glossy finish when produced with color. Some examples of common products made with PP are dairy and medication containers. Polypropylene is suitable for hot fill applications of up to 165°F and is therefore great for autoclaving. It is not recommended for cold or sub-freezing temperatures. The Cary Company has an assortment of polypropylene plastics available for purchase, such as plastic caps and jars, which have a higher tolerance for chemical products. Disclaimer: This information has been provided as a general guide. It is the customer's responsibility to select the proper container for product and application compatibility. Material PP Dimensions 2.4" Dia. x 1.02" H Weight 0.1 lbs. Case Pack 200 ea. Case Dimensions 15" L x 15" W x 16" H Case Weight 20 lbs. Pallet Pack 4,800 ea. (24 Cases) Pallet Dimensions 40" L x 48" W x 60" H Pallet Weight 480 lbs. Country of Manufacture United States Gasket EPDM Rubber Gasket
$14.00
2" Stubby Buttress to NPT Adaptor
2" Stubby Buttress to NPT Adaptor This adapter converts 2" (50mm) male buttress pipe threads to 2" male NPT pipe threads. The adapter incorporates female buttress threads on one end and male NPT threads on the other for connecting pipes and valves with different ends. Made of tough polypropylene (PP), this adapter also incorporates an ethylene propylene diene monomer (EPDM) gasket for a leak-tight connection. Shallow profile ensures valve does not protrude past IBC tote cage. Key benefits: Converts 2" male buttress pipe thread to a 2" male NPT pipe thread 2" long profile does not protrude past IBC cage during transport Made of PP EPDM gasket ensures a secure seal Suitable for use in a wide variety of liquid handling applications Proudly Made in the USA Material: Polypropylene (PP) is a tough plastic that has good chemical resistance. PP is translucent in its natural state but can have a glossy finish when produced with color. Some examples of common products made with PP are dairy and medication containers. Polypropylene is suitable for hot fill applications of up to 165°F and is therefore great for autoclaving. It is not recommended for cold or sub-freezing temperatures. The Cary Company has an assortment of polypropylene plastics available for purchase, such as plastic caps and jars, which have a higher tolerance for chemical products. Disclaimer: This information has been provided as a general guide. It is the customer's responsibility to select the proper container for product and application compatibility. Material PP Dimensions 2.4" Dia. x 1.02" H Weight 0.135 lbs. Case Pack 200 ea. Case Dimensions 15" L x 15" W x 16" H Case Weight 27 lbs. Pallet Pack 4,800 ea. (24 Cases) Pallet Dimensions 40" L x 48" W x 60" H Pallet Weight 648 lbs. Country of Manufacture United States Gasket EPDM Rubber Gasket Note: Color may vary.
$12.00
BVV 2540 Nanofiltration Skid
BVV 2540 Nanofiltration Skid Note: This product carries 8 - 12 week lead time Perform organic solvent recovery or botanical extract decolorization with ease with our 2540 nanofiltration skid. BVV's 2540 Nanofiltration Skid is designed to meet Class 1 Division 1 standards. With the ability to recover 30 gallons of ethanol per hour without the application of heat preserving target compounds and utilizing a fraction of the energy consumption of a traditional falling film. Processing Power Capacity: 15 GPH or 30 GPH of solvent recovery. Solvents: Ethanol, Methanol Specifications 4X 2540 nanofiltration housings Stainless steel 6GPM pump with PTFE seals 7.5HP C1D1 1750 RPM Motor 7.5HP VFD 1/60/230 NEMA 4X enclosure (13A) Insulated 2"x18" Heat Exchanger Polyscience 1.5HP Chiller 230/60/1/23.1 700PSI Pressure Relief Valve C1D1 Flowmeter 2X 0-1000 PSI Pressure Gauges 1.5" Intake & Retentate Lines 1/2" Permeate & Pressure Relief Lines Footprint (DxWxH) 30"x39"x79" Weight: 400 lb Maximum Pressure Rating: 700PSI Performance Variable Frequency Drive-based flow control Complete pressure control with manual pressure controls Retentate cooling with inline Heat exchanger & chiller 700PSI pressure relief valve with diversion line *Components shown are subject to change**This unit is meant for bulk solvent recovery, 90% of the total volume of solvent an additional solvent recovery apparatus is recommended to evaporate to dryness*
$41,000.00 - $45,000.00
Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 25 Cubic Feet - ETL Rated
Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 25 Cubic Feet - ETL Rated The brand new Neocision ETL Rated 25 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting. Every unit accompanies various safety and protection features taking into consideration user and item safety. These highlights incorporate high and low-temperature alerts. These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. Key Features: ETL Rated Durable Powder Coated Exterior Touch Screen LCD with Datalogging Capabilities Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters (3) 1" ID Ports for putting lines through the freezer Backup battery Included. Specifications Model Number BVV™-86C25 Voltage 115V / 60Hz / 15A Wattage 1800w Capacity 25cu ft. / 730L Internal Dimensions 34.5" x 51.5" x 23.5" Exterior Dimensions 43" x 76" x 36" Temperature Range -40°C to -86°C Weight 700lbs Rating ETL Rated
$8,000.00$7,000.00
BVV M24 - 1/2" MNPT Huber Adapter
BVV M24 - 1/2" MNPT Huber Adapter This zinc plated adapter is meant to be used on Huber Unistats with male M24 threads to adapt to 1/2" MNPT. These fittings must be used in conjunction with M24 Bonded seal washers to create a complete seal. Bonded Seal Specifications For Thread Type Metric For Gender Male For Thread Size M24 Washer Material Steel Gasket Material Buna-N Rubber Temperature Range -20° to 230° F Thickness 2mm RoHS RoHS 3 (2015/863/EU) compliant with exemption 6(a)-I - Lead as an alloying element in steel
$285.00
Jacketed Reactor with Motor and Collection Vessel
Jacketed Reactor with Motor and Collection Vessel This jacketed reactor kit includes your choice of a C1D1 motor, standard motor, or non-electric air powered motor (air compressor required). If using an electric motor it will require wiring to the included speed controller. Using the jacketed reactor to heat your solution, use your reactor to mix your solution during the heating process. The condenser and collection vessel allow you to recover residual solvents up to 100L. The collection vessel includes a dip tube to empty the vessel and a 1/4" JIC flare to input pressure into the base to assist in emptying the tank through the dip tube. This system does NOT include a heater or chiller, please inquire with your account representative for recommendations based on your application! Jacket connections are 1/2" hose barbs. Mixer Type Pneumatic Electric C1D1 Electric Horsepower 3/4 HP 3/4 HP 1 HP Power Air Compressor 120V 220V 1ph Reactor Size 150L Collection Size 50L / 100L Jacket Connections 1/2" Hose Barb
$7,022.00 - $13,690.00
Adapter M30x1.5 male to male
Adapter M30x1.5 male to male Adapter M30x1.5 male to male
$238.00
Compressor Head BARE for BVV Recovery Pump/ CMEP Retrofit
This is a replacement compressor head for the BVV2CYL, BVV4CYL, and BVVCMEP-RETRO. It is a full stainless steel head and has all the proper holes drilled to fit on our recovery pumps.
$35.00$23.00
Carbon Chemistry ALX (Alumicel N)
Carbon Chemistry ALX (Alumicel N) An acidic powder media designed for powerful polar adsorption and separation processes. This finely-milled activated alumina provides superior removal of basic compounds and color bodies, making it ideal for precise purification and filtration applications. Its optimized acidic surface chemistry enhances control in separations of basic compounds and targeted impurity removal. Neutral; pH 6.7 Used for Chromatography Commonly used as an aid for decolorizing Download Safety Data Sheet
$200.00 - $960.00
True Terpenes Lemon Kush
True Terpenes Lemon Kush Fragrance: Lemon Mango Pepper Florals Effects: Soothing Focused Lemon Kush brings the tangy sweet of lemons together with the skunky, earthy flavors that Kush is known for. The blending continues to the effects. Lemon Kush may put you on the couch, but you’ll be ready to talk. Storage Requirements: Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store in a cool dry place. Improper storage can cause terpenes to degrade. Dilution: Terpene Strain & Flavor-Infused Strain Profiles, Effects-Based Terpene Profiles & Terpene Flavors:The Terpene products above must be diluted prior to use. (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Viscosity Extract Modifier: The Terpene product above must be diluted prior to use. (1-3% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With Care: Can cause skin irritation, do not use PRIOR to dilution. Lemon Kush-Specific Certificates: Product Specification All Natural Certificate of Analysis Safety Data Sheet Food Safety Company-Specific Certificates: ISO 9001:2015 GMP Certification FSSC 22000
$121.50 - $2,250.00
True Terpenes Jack
True Terpenes Jack All sales are final. Orders can be refunded prior to fulfillment and shipping but once the order has been fulfilled and/or shipped, no refunds will be issued. Due to the hazardous nature of our product, we are unable to accept returns. (Please Note: This product has 2 week lead time) Fragrance: Gas Lemon Clove Effects: Uplifting Insightful Named for a legendary activist, this profile is a legend itself. Heavy fuel aroma spills out with pepper, citrus balancing it out. Storage Requirements: Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store in a cool dry place. Improper storage can cause terpenes to degrade. Dilution: Terpene Strain & Flavor-Infused Strain Profiles, Effects-Based Terpene Profiles & Terpene Flavors:The Terpene products above must be diluted prior to use. (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Viscosity Extract Modifier: The Terpene product above must be diluted prior to use. (1-3% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With Care: Can cause skin irritation, do not use PRIOR to dilution. Jack-Specific Certificates: Product Specification Certificate of Analysis Safety Data Sheet Food Safety Company-Specific Certificates: ISO 9001:2015 GMP Certification FSSC 22000
$121.50 - $2,250.00
True Terpenes Grape Ape
True Terpenes Grape Ape Fragrance: Grape Berry Lavender Pine Effects: Peaceful Serene The Grape Ape cultivar that inspired our terpene profile is descended from cultivars as varied as Mendocino Purps, Skunk, and a legendary Afghani landrace. The combination of these parents has created a profile that gives the aroma of grapes, tropical fruit, earth and a pine forest. These varied smells merge into a soothing wave. Linalool and ocimene lend a hand with floral, fruity tones and enhance the chill vibe of myrcene. Storage Requirements: Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store in a cool dry place. Improper storage can cause terpenes to degrade. Dilution: Terpene Strain & Flavor-Infused Strain Profiles, Effects-Based Terpene Profiles & Terpene Flavors:The Terpene products above must be diluted prior to use. (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Viscosity Extract Modifier: The Terpene product above must be diluted prior to use. (1-3% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With Care: Can cause skin irritation, do not use PRIOR to dilution. Grape Ape-Specific Certificates: Product Specification Certificate of Analysis Safety Data Sheet Food Safety Company-Specific Certificates: ISO 9001:2015 GMP Certification FSSC 22000
$121.50 - $2,250.00
True Terpenes Grandaddy Purple
True Terpenes Grandaddy Purple Fragrance: Sweet Floral Earth Effects: Soothed Tired Hungry Euphoria Grandaddy Purple (GDP) is a low from California with deep purple blooms. It is a cross between Big Bud and Purple Urkle. The effects of this sweet, grape/berry flavored, powerful strain are both euphoric and soothing. In addition to feeling soothed, patients describe feeling tired, happy, and hungry. Storage Requirements: Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store in a cool dry place. Improper storage can cause terpenes to degrade. Dilution: Terpene Strain & Flavor-Infused Strain Profiles, Effects-Based Terpene Profiles & Terpene Flavors:The Terpene products above must be diluted prior to use. (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Viscosity Extract Modifier: The Terpene product above must be diluted prior to use. (1-3% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With Care: Can cause skin irritation, do not use PRIOR to dilution. Grandaddy Purple-Specific Certificates: Product Specification All Natural Certificate of Analysis Safety Data Sheet Food Safety Company-Specific Certificates: ISO 9001:2015 GMP Certification FSSC 22000
$121.50 - $2,250.00
True Terpenes God's Gift
True Terpenes God's Gift Fragrance: Earthy Pine Berry Effects: Soothing Couch-Lock God’s Gift is as the name implies descended from heaven. It’ll put your head in the clouds. Earthy musk and pine aromas mix with a floral, berry sweetness. Storage Requirements: Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store in a cool dry place. Improper storage can cause terpenes to degrade. Dilution: Terpene Strain & Flavor-Infused Strain Profiles, Effects-Based Terpene Profiles & Terpene Flavors:The Terpene products above must be diluted prior to use. (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Viscosity Extract Modifier: The Terpene product above must be diluted prior to use. (1-3% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With Care: Can cause skin irritation, do not use PRIOR to dilution. God's Gift-Specific Certificates: Product Specification Certificate of Analysis Safety Data Sheet Food Safety Company-Specific Certificates: ISO 9001:2015 GMP Certification FSSC 22000
$121.50 - $2,250.00
True Terpenes Forbidden Guava
True Terpenes Forbidden Guava Fragrance: Hybrid Fruity Citrus Effects: Rest Calm Bold and juicy, Forbidden Guava fills the nose with guava, cherry, and papaya. The complex profile marries sweetness, warm florals, and a distinctly tropical richness, from the aroma’s yeasty cheese base. Storage Requirements: Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store in a cool dry place. Improper storage can cause terpenes to degrade. Dilution: Terpene Strain & Flavor-Infused Strain Profiles, Effects-Based Terpene Profiles & Terpene Flavors:The Terpene products above must be diluted prior to use. (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Viscosity Extract Modifier: The Terpene product above must be diluted prior to use. (1-3% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With Care: Can cause skin irritation, do not use PRIOR to dilution. Forbidden Guava-Specific Certificates: Product Specification Certificate of Analysis Safety Data Sheet Food Safety Company-Specific Certificates: ISO 9001:2015 GMP Certification FSSC 22000
$121.50 - $2,250.00
BVV Compression 10" Tri-Clamp x (2) 2" Tri-Clamp x (1) 1.5" TriClamp x (2) 3/8" Compression x 1/4" Compression x 1/2" Compression Hemispherical Lid
BVV Compression 10" Tri-Clamp x (2) 2" Tri-Clamp x (1) 1.5" TriClamp x (2) 3/8" Compression x 1/4" Compression x 1/2" Compression Hemispherical Lid This End Cap comes with (4) Compression connections and (2) 1.5" and (1) Tri-Clamp ferrules welded to the end cap with a sanitary weld with a 3" Tube Extension Below the Lid. They allow the user to adapt and connect a tube stub connection to the (1) 1/4", (2) 3/8", and (1) 1/2" port on a Tri-Clamp lid and the Tri-Clamp Connections. These 7 connections are welded on a 10" Hemispherical Tri-Clamp End Cap. Specifications Material: 304 Stainless Steel Connection Types: (2) 2" and (1) 1.5" Tri-Clamp with 3" Tube Extension Below Lid on Center Tri-Clamp Port 10" Tri-Clamp (1)1/4", (2) 3/8" and (1)1/2" Female Compression Connections Standard: 3A
$320.00
BVV Replacement Centrifuge EX Motors
BVV replacement centrifuge EX motors for BVV 45L and 475L centrifuges.
$750.00 - $1,750.00
Swivel Bosshead
This swivel boss head is made out of die-cast alloy is nickel plated and will fit rod diameters up to 16mm. The boss head can be adjusted and locked to any angle (360°). It is also designed to carry heavy loads and prevent torque damage. Note:Clamps and rods are NOT included.
$10.00
Siemens Touch Screen Controller with Explosion Proof Housing for Centrifuges
Siemens Touch Screen Controller with Explosion Proof Housing for Centrifuges Disclaimer: When bought separately and NOT with our Centrifuge this item will have no warranty and all sales are final. Industrial Centrifuges are used to separating liquids from solids and this style of centrifuge excels at alcohol extraction by forcefully separating the alcohol from the biomass. Controller: This centrifuge is controlled by a Siemens Smart Line PLC. This PLC is pre-programmed to have both a soaking cycle, shown as AGITATION TIME on the screen, and a spin drying cycle, made of 4 separate specifications. SPIN TIME 1 through 4 allow the user to choose four different speeds and however long they wish to be at each speed. All four parameters labeled as SPIN TIME combine to make one spin cycle when the Spin button is pressed. To change a parameter, simply tap on the number to be changed and type in the desired value when prompted on screen. Any number displayed within a white box can be adjusted. SPEED SET: This number represents the RPM as a percentage of the machine max speed. In this case the max speed is 1500RPM. SET: This column will dictate how long the centrifuge spins for a cycle or at a specified speed within the cycle. For the Agitation Time, the Set value will control the total length of the agitation cycle. The FWD/REV TIME will control how long the basket will spin in one direction before reversing to cause agitation. The “current” value will only count up while at the set speed for the agitation cycle. CURRENT: The “current” column will give a readout of how long the basket has been spinning at the set speed. This value will not increase while the centrifuge is increasing speed between SPIN TIME values. When running the agitation cycle, it will be complete when the count of seconds in the CURRENT reaches the value in the SET column. The centrifuge will stop automatically. For the spin cycle, the centrifuge will go through all 4 set SPIN TIME values, the CURRENT column will only begin to count when the centrifuge is at the set speed. The cycle time will not account for time taken to get up to speed. Temperature: Shows a live readout of the temperature inside the centrifuge.Inlet Valve and Drain Valve: These are two pre-programmed buttons that can be used with electronic valves. This unit does not come standard with these valves, but leaves the option open for them to be added. Electrical Power Size Specification 45L Input: 240V 1ΦOutput: 240V 3Φ 4kW 160L Input: 240V 1ΦOutput: 460V 3Φ 7kW 280L Input: 240V 1ΦOutput: 460V 3Φ 11kW 475L Input: 240V 3ΦOutput: 460V 3Φ 11kW
$7,900.00 - $9,500.00
Corken T-491 Oil-Free Gas Compressor
Corken T-491 Corken hydrocarbon gas compressor are used to handle butane, propane and isobutane. Benefits of Corken's Gas Compressor: Cost effective: Motor driven unit does not require a pneumatic driver/air compressor Fast recovery time: High Capacity design shortens recovery time and increases production. Low evacuation pressure: 0 psig or lower evacuation pressure Space Saving: Eliminates the need for a separate air compressor, Oil-free Compression: No contamination of gas products Food Grade material: PTFE trim nickel coating for gas wetter parts. Quiet: Noise rating of approximately 85dBa os beneficial to an enclosed explosion proof processing area. T-491 OUTLINE Drawing T-491 SPECIFICATION D / T Model
$45,000.00
Refurbished Water Circulation Vacuum Pump
Refurbished Water Circulation Vacuum Pump ***NOTE: Refurbished items are 100% re-tested at our warehouse to be fully functional. The customer acknowledges that by buying a refurbished product may or may not have imperfections or slight damage to the item such as: Major/Minor Scratches Major/Minor Dents Smells or Odors (cleaned as much as possible at warehouse) This Circulation and Vacuum Pump combines the best of both worlds by using the circulating water to pull a vacuum which requires no oil at all and has very low maintenance requirements overall due to this unique process and design. Each vacuum port on the unit pulls vacuum separately from one another so the user can use it for different applications at the same time or combined to increase the vacuum. This pump will also circulate water through the backports as needed to cool and application and dissipate heat as needed. Specifications Vacuum Degree 0.0980Mpa (735 Torr) @ 25°C Single Tap Exhaustion 10L/min Voltage 110V / 50Hz USA Plug Noise <50DB Number of Vacuum ports: 2qty (independent vacuum po Vacuum Port Size: 3/8" Vacuum Depth: 16 torr Number or Water Circulation inlet: 1qty Number or Water Circulation Outlet: 1qty Pumping Speed: 6.5 L/min Reservoir Capacity: 12L Overall Dimensions: 15.5" x 11.5" x 17" Decibel: 62 dB Weight (no water): 17lbs 10oz
$340.00$175.00
3′ Fisher American Fume Hood
3′ Fisher American Fume Hood sku NLS - 301 NLS - 302 NLS - 303 NLS - 304 NLS - 305 NLS-306 Color White White White Blue Blue Blue Fume Hood Exterior Dimensions: Width: 36″ 36″ 36″ 36″ 36″ 36″ Depth: 31 1/2″ 31 1/2″ 31 1/2″ 31.5″ 31 1/2″ 31 1/2″ Height: 54 1/2″ and 89 1/2″ with cabinet 54 1/2″ and 89 1/2″ with cabinet 54 1/2″ and 89 1/2″ with cabinet 54.5″ 54 1/2″ and 89 1/2″ with cabinet 54 1/2″ and 89 1/2″ with cabinet Work Area (Interior) Dimensions: Width: 26″ 26″ 26″ 26″ 26″ 26″ Depth: 23″ 23″ 23″ 23″ 23″ 23″ Height: 46″ 46″ 46″ 46″ 46″ 46″ Fume Hood Accessories: Light on/off Switch Light on/off Switch Light on/off Switch 1 Light on/off Switch Light on/off Switch Light on/off Switch 1 AC Power Plug 1 AC Power Plug 1 AC Power Plug 1 AC Power Plug 1 AC Power Plug 1 AC Power Plug 1 Cold Water Valve 1 Cold Water Valve 1 Cold Water Valve 1 Cold Water Valve 1 Cold Water Valve 1 Cold Water Valve 1 Gas Valve 1 Gas Valve 1 Gas Valve 1 Gas Valve 1 Gas Valve 1 Gas Valve 1 Horizontal sliding glass door 1 Horizontal sliding glass door 1 Horizontal sliding glass door 1 Vertical Sliding Sash Door with 2 horizontal sliding glass windows 1 Horizontal sliding glass door 1 Horizontal sliding glass door 1 General Storage 1 ACID Storage 1 Flammable Storage 1 Flammable Storage 1 Acid Storage 1 General Storage
$6,825.00 - $8,525.00
Huber adapter M16x1f-1/2"m
Huber adapter M16x1f-1/2"m Adapter M16x1 f - R1/2 m Adapter M16x1 f - R1/2 m M16x1 female thread to R1/2 male thread
$135.00
DigiVac SNAP Vacuum Controller | Simple, Nimble, Automatic Process Control | Up to 8 Recipes
DigiVac SNAP Vacuum Controller | Simple, Nimble, Automatic Process Control | Up to 8 Recipes Description SNAP Vacuum Controller | Simple, Nimble, Automatic Process Controller with up to 8 Recipes SNAP: Automatic Vacuum Process Controller | Vacuum control and venting with the touch of a button or twist of a dial Vent your vacuum chamber or equalize your system with the touch of a button instead of pulling hoses or turning valves Treat material in chamber more gently by implementing kinder ramp rate controls which is ideal for freeze drying, vacuum drying or lyophilization applications Vacuum Controller with onboard ramp rate recipe control. Set up to 8 recipes based on time and pressure setpoints. Dashboard pushbutton control for START, STOP functionality for each channel allows you to automatically vent or isolate your system with a push of a button Ideal for automating and simplifying vacuum chamber pressure control. SIMPLE – SIMPLIFY YOUR LAB & CONTROL MORE WITH LESS Applications: vacuum chamber (from 1 liter to 1000 liters) research, vacuum ovens/vacuum drying, vacuum furnaces, large scale food processing, microwave drying, composites, rotary evaporators, falling film systems Fine control of target vacuum pressure for more precise processing and research Enables using reliable and long lasting rotary vane pumps & dry scroll pumps in applications where diaphragmpumps were previously required Keeps vacuum pumps near their base pressure resulting in greater longevity NIMBLE – MAXIMIZES THROUGHPUT & PUMPDOWN SPEED Largest flow paths available to insure maximum flow for faster evaporation Maximize throughput and pump down speed with a 20 mm vacuum path (almost full KF25 orifice) AUTOMATIC PROCESS – PRECISION CONTROL & INTUITIVE DESIGN Automatic Vacuum Process Controller | precise automated control with programmable recipes and graphing of vacuum levels Innovative valve control performs both proportional throttle and bleed vacuum control (vent to atmosphere) The integrated bleed design allows you to quickly vent to atmosphere to stop bumping during processing Numerical readings right on the LCD screen and one touch buttons: VENT, CLOSE (isolate, close all valves) and FULL VAC (fully opens the valve for vacuum pump and closes the vent valve) SNAP Vacuum Controller Wetted Material Options Aluminum (6061) wetted surfaces Stainless steel (304) wetted surfaces Measurement and Control Range: 1 Torr to 775 Torr (standard) Need millitorr range?: SNAP has a RJ45 Port for adding an additional sensor to extend the measurement range. We recommend the addition of the DCP Quantum to be able to monitor and control from 0.01 Torr to 1000 Torr. DigiVac SNAP Data Sheet DigiVac SNAP Operational Manual DigiVac SNAP Quick Start Guide
$5,100.00$4,650.00
PTFE WFE Wipers - 3 Pack
PTFE WFE Wipers These wipers are designed for wiped film evaporators spinning counterclockwise. Pack of 3 Dimensions: 15.375L x .38W x .42D
$350.00
Beaker & Wrench 40L Complete Dosing System
Beaker & Wrench 40L Complete Dosing System Please note: This Product has 1 week lead time For Wiped Film Evaporators The 40L Complete Dosing System by Beaker & Wrench® is a continuous feed system that connects to any Wiped Film Evaporator effortlessly. Optimize your time and end results by dialing into your feed system. The Feed Gear Pump by Beaker & Wrench® gives the operator control over flow rate and freedom to load material into the flask without breaking deep vacuum. Once attuned with the flow rate, calculations become less of a guessing game and more of a formula. Distill as slow or as fast as needed! The contents of this system include: Heated 40L feed flask Crude Cozy™ Digitally operated, heated Feed Gear Pump 4″ tri-clamp port on feed lid Inlet adapter (for your still) 6′ Heated Transfer Line (not pictured) Wattage: 90/ft, 120 Volts Maximum Temp: 150°C UL Listed 3 Channel PID Temperature Controller UL: E510826 How does it work?Crude is loaded into a heated feed flask, which then flows through the heated Gear Pump. The Gear Pump moves fluid through the gears while maintaining vacuum. Oil is then pulled towards the still body, ready for distillation! Cleaning:Every Operator has their own preference in how they clean their Wiped Film Evaporator. Ethanol, Isopropyl alcohol or vegetable oil are viable options when looking to clean your Wiped Film. Step-by-step instructions are included in the manual! Installation: Are you interested in having a Beaker & Wrench® technician install your Complete Dosing System? Click here for a quote! The advantage with having a technician perform installation is you can ask any and all questions necessary on how to process with your Wiped Film Evaporator! What is the warranty?1 year manufacturer’s warranty on parts for exchange. Customer has 5 days from day of delivery to inspect equipment for breakages or damage. ** Please indicate the inlet size of your still in the Notes section of your purchase. This will help us adapt to your set-up.
$13,500.00
Polyscience 3 HP High Capacity Chiller; Air-Cooled - Up to 10.5kW @ 20°C
Polyscience 3 HP High Capacity Chiller; Air-Cooled - Up to 10.5kW @ 20°C Key Specifications Description: 3 HP Chiller; Air-Cooled; Up to 10.5kW @ 20°C Display: LED Connectivity: Standard: RS232; Optional: RS485 Working Temperature Range °C: 5° to 35° Temperature Stability °C: ±0.5° Temperature Calibration Capability: 1-point Key Features Chillers 2HP and up are not available outside of the United States High capacity cooling for lasers, EDM equipment, injection molding, and other heat removal applications Displays temperature and pressure or flow rate simultaneously User-adjustable temperature, pressure, and flow rate alarms Simple operation and maintenance Air- or water-cooled (3 HP models) Wide variety of pump options available Common Specifications Working Temperature Range °F 41° to 95° Working Temperature Range °C 5° to 35° Cooling Capacity Up to 10.5kW @ 20°C Reservoir Capacity (gallons) 7 Reservoir Capacity (liters) 26.5 Reservoir/Tank Material Contact PolyScience for Options Reservoir Cover Screw-on Cap Cleanable Air Filter Yes Cleanable Fluid Filter Yes Temperature Stability °F ±0.9° Temperature Stability °C ±0.5° Display LED Display Resolution (Read) 0.1 Pump Type Contact PolyScience for Options Process Connections 3/4" (F) NPT Over-Temperature Protection / Failsafe Heater Control Yes Reservoir Liquid Level Indicator Yes Cool Command Refrigeration Technology Yes Reservoir Drain Yes Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 30.5 x 37 x 42 in Overall Dimensions (L x W x H) (cm) 78 x 94 x 107 cm Compressor Size (HP) 3 Refrigerant R134a Shipping Weight (pounds) 570.0 Shipping Weight (kilograms) 259.0 Catalog Page Number 105 Operator's Manual PDF Version
$15,350.00
You have seen 1488 out of 1820 products