Lab Equipment
So-Low -85°C Ultra-Low Chest Freezer - 3 Cubic Ft.
So-Low -85°C Ultra-Low Chest Freezer - 3 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! So-Low Ultra-Low Chest Freezers are second to none in low temp applications to suit any laboratory or application needs. These Ultra-Low Temp freezers feature digital temperature control with 2 temperature displays. One shows the set temperature and the other shows the actual temperature in the freezer. The So-Low C85-3 features a battery operated alarm system that will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Specification Data Sheet Diagram Data Sheet Specification Manufacturer So-Low Temperature Range -40°C to -85°C / -40°F to -121°F Capacity 3 Cubic Ft. / 83 Liters Dimensions: Exterior: 34.5" x 25.25" x 48" Interior: 24" x 12" x 18" Refrigeration System So-Low cascade type. Two hermetic compressors. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish.
$6,300.00 - $7,480.00
Cascade CDO-5 Dry & Decarb Oven, 5 cu ft, 2 Mesh Bags
Cascade CDO-5 Dry & Decarb Oven, 5 cu ft, 2 Mesh Bags This item carries up to a 2 week lead time. Cascade’s CDO-5 is purpose-built for bench-top, R&D drying and decarboxylation of material with additional features: Built-in Humidity Sensor assists in monitoring dryness Adjustable stainless steel shelves – 2 each NRTL Certification 2 each FDA temp rated fine micron mesh bags for ground material – Mesh bags are required to prevent oven contamination and ground material loss. This powerful benchtop forced air laboratory oven uses heated air to remove unwanted compounds from products that are not temperature sensitive. Our ovens feature horizontal airflow that enables more consistent distribution of air. They are designed to have uniform temperatures and airflow across the shelf space from right to left. The CDO-5 includes a built-in humidity sensor and fine micron mesh bags for drying or decarboxylating powders or ground material. Ideal Uses: R&D, laboratory scale forced-air convection drying Decarboxylation processes Drying organic material. Drier material will yield better results than processing wet material. Removing as much moisture as possible pre-processing will save time in in the post process of vacuum purge and winterization. Lab glassware dryer Model CDO-5 Features Horizontal Airflow. The airflow moves uniformity across the shelf space from right to left Digital set-point control, timer and overtemp failsafe protection Humidity sensor displays relative humidity levels during process Stainless steel interior / Food lab-grade construction 1 Year Warranty Includes 2 stainless steel shelves, height adjustable with mounting clips Includes 2 temp rated mesh bags for easy loading & uniform drying of messy powders, ground up or turbulent materials Triple wall construction the CDO-5 meets CE, UL and TUV requirements to keep work-spaces cool Quality made in Oregon USA 120V / 1ph / 14FLA NEMA 5-15P Plug Supplied (220V 1 PH Version available) The Cascade Difference Basic forced-air lab ovens are mass-produced and sold by many large scale laboratory equipment distributors. But there are key differences between Cascade and other less costly, often imported lab ovens: Independent Overtemp Failsafe Protection The Cascade Sciences CDO-5 is equipped with a heating cutoff system that will automatically stop power to the heaters when the overtemp setting is tripped. This protection system will provide peace of mind for overnight or unattended drying processing. NRTL Certification No Extra cost. The CDO-5 Oven comes certified by the Nationally Recognized Test Lab, TUV. This certification is a requirement by many municipalities. CAN/CSA-C22.2 No. 61010-1:2012 +UPD No. 1:2015-07 + UPD No. 2:2016-04 CAN/CSA-C22.2 No. 61010-2-010:2015 UL 61010-1:2012-05 UL 61010-2-010:2015 EN 61010-1:2010 EN 61010-2-010:2014 Rigorous Quality Assurance in an ISO Certified, USA Manufacturing Facility Cascade Sciences manufactures our ovens in Oregon, USA. We are proud of our ISO 9001 Certification/Accreditation. Each oven completes a series of quality assurance procedures before shipment: Electrical & mechanical safety is thoroughly tested in compliance with TUV requirements Functional testing verifies user settable items consistent with most lab protocols/usage models Temperature verification includes calibration & temp chamber uniformity following ASTM standards Units are cleaned and packed in ISTA tested, certified packaging materials Specifications Capacity Volume 4.9 Cubic Ft. / 138 Cubic Liters Interior Dimensions 21” x 19.44” x 20.75”534mm x 494mm x 527mm Exterior Dimensions 34.1” x 28.1” x 38.75”866mm x 711mm x 984mm Temperature Temperature Range +2°C (36°F) above room temp to 180°C (350°F) Temp Stability +/-0.4 °F Temp Uniformity @ 40°C (100°F): +/- .5°C (1°F)@ 115°C (240°F): +/- 1°C (1.5°F)@ 150°C (305°F): +/- 2°C (3°F) Heat up / Stabilization Time from 25°C (77°F) to 115°C (240°F) 40 minutes Air Statistics Airflow Exchanges 220 per hour @ 80°C (176°F) Linear Shelf Space Airflow 145 Feet Per Min (44 Liters Per Min) Air Intake Adjustable side vents. Air Exhaust Adjustable. Top 2.75: Dia Exhaust Airflow @ 80°C (176°F) 18.5 Feet Per Min (523.9 Liters Per Min) Shelving 18.5 Feet Per Min (523.9 Liters Per Min) Fits 5 maximum Surface Area (W x D): 20.75″ x 19″ Weight Capacity: 50lbs Bags Comes with 2 Temp Rated Mesh Bags, fits four max Material Polypropylene (PP) Melt Temperature 161°C (363°F) Softening Point 152°C (305°F) Heat Deflection Temperature 90°C (194°F) Glass Transition Temperature 0°C (32°F) * Mesh bags are REQUIRED to prevent oven contamination and ground material loss. * Polypropylene products produced for some filtration applications are made from resin that complies with FDA regulations for food contact. The regulation compliance is product number dependent / specific. * Impact at cold temperatures is likely to cause strand cracking or breakage Certifications ISO 9001NRTL TUV #U8 170464972 077CAN/CSA-C22.2 No. 61010-1:2012+ UPD No. 1:2015-07 + UPD No. 2:2016-04CAN/CSA-C22.2 No. 61010-2-010:2015UL 61010-1:2012/R:2016-04UL 61010-2-010:2015EN 61010-1:2010EN 61010-2-010:2014 Warranty 1 Year
$7,607.00
30L Glass Axis
30L Glass Axis Oil Filled Vacuum/Pressure Gauge - Bottom Mount *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$140.00
2L BVV™ Rotary Evaporator Turnkey Setup
2L BVV™ Rotary Evaporator Turnkey Setup 2L Electric Lift Rotary Evaporator turnkey setup includes all the necessary components to successfully perform solvent recovery via rotary evaporation. A cold trap should always be used inline between your vacuum system and application to protect the pump from volatile vapors. 2L Rotary Evaporator Turnkey Setup includes: 2L Electric Lift Rotary Evaporator 90-day limited warranty (excludes glassware, consumables & moving parts) BVV NEO 1.4 CFM Diaphragm Pump ETL Rated OR. 3.5CFM Dry Floating Scroll Vacuum Pump Polyscience LS -20C to 40C 1/2HP Chiller w/ Turbine Pump OR BVV NEOCISION 20L Chiller (-40C) - ETL Rated 10ft of Vacuum Tubing 20ft of Chiller Tubing 10 Pack of Adjustable stainless steel hose clamps 3/8" Vacuum Manifold Optional add-on : BVV™ CT40 -40°F 300ml x 3 Cold Trap, BVV™ CT80 -112°F 300ml x 3 Cold Trap Optional add-on: J-KEM DVR-200 Digital Vacuum Regulator Optional add-on: Heat Transfer Fluid -- NuTherm PF-50 or Dynalene HC-50 Rotovap Quick Start Guide This guide gives basic quick start instructions for rotovaps. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs. Clean and assemble unit. Make sure all pieces are cleaned and sterilized using an alcohol solution. Connect chiller to the condenser and set to 0C (32F). Always fill a rotovap condenser from the top down (chiller output to top of the condenser, chiller input to bottom of the condenser). Connect vacuum pump to cold trap and connect cold trap to the vacuum port on rotovap. Turn on heat bath and set to 40C (113F). Once heat bath, chiller, and cold trap have reached desired temperatures, turn on the rotovap motor and set the speed to approximately 100 RPM (does not have to be precise). Keep in mind, higher RPM’s will increase evaporation power but also increase heat load. Start vacuum pump and allow vacuum to pull down for a few minutes before injection. Once the vacuum has been pulled to a sufficient level (does not have to be precise but should be below 100 Torr), using the injection valve, very slowly inject approximately 500 mL of solution into evaporating flask and then close the valve. Allow this small amount to begin evaporating. You may see the chiller begin to rise in temperature, this is called “priming” the rotovap. Once the temperature stops rising or all liquid is almost completely evaporated, open the injection valve again very slowly so that a small amount of liquid begins to enter the evaporating flask. Do not close injection valve this time but continue to allow the solution to enter the evaporating flask. At this point, you must try to match the input speed to the output speed. What this means is that you should be injecting the same amount of liquid into the rotovap that is equal to the amount of liquid dripping from the condenser into the receiving flask. You will know that the input speed and output speed are matched because the chiller will remain at a stable temperature. If the chiller begins to rise, then you are injecting too much liquid. Dial back the valve until the chiller stabilizes. Once everything is stabilized, you may walk away from the rotovap if necessary. Check every so often to make sure temperatures remain stable and evaporation continues efficiently. ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***
$7,000.00 - $13,500.00
20L Neocision ETL Lab Certified Rotary Evaporator Turnkey System
20L Neocision ETL Lab Certified Rotary Evaporator Turnkey System 20L NEO Rotary Evaporator Turnkey System setup includes all the necessary components to successfully perform solvent recovery via rotary evaporation. A cold trap should always be used inline between your vacuum system and application to protect the pump from volatile vapors. To keep your bath heating properly, this unit should only be used with RO or DI water. 10-50L NEO and ECO Rotary Evaporator Diagram 20L NEO Rotary Evaporator Turnkey System setup includes: 20L Neocision ETL Lab Certified Rotary Evaporator Polyscience 6160T 1HP Chiller 3/8" Gum Rubber - 100ft 3/8" Silicone Tubing - 25ft Welch BTpro100 Diaphragm Pump Adjustable Stainless Steel Hose Clamps Rotovap Quick Start Guide This guide gives basic quick start instructions for rotovaps. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs. Clean and assemble unit. Make sure all pieces are cleaned and sterilized using an alcohol solution. Connect chiller to condenser and set to 0C (32F). Always fill a rotovap condenser from the top down (chiller output to top of condenser, chiller input to bottom of condenser). Connect vacuum pump to cold trap and connect cold trap to vacuum port on rotovap. Turn on heat bath and set to 40C (113F). Once heat bath, chiller and cold trap have reached desired temperatures, turn on rotovap motor and set speed to approximately 100 RPM (does not have to be precise). Keep in mind, higher RPM’s will increase evaporation power but also increase heat load. Start vacuum pump and allow vacuum to pull down for a few minutes before injection. Once vacuum has been pulled to a sufficient level (does not have to be precise but should be below 100 Torr), using the injection valve, very slowly inject approximately 500 mL of solution into evaporating flask and then close the valve. Allow this small amount to begin evaporating. You may see the chiller begin to rise in temperature, this is called “priming” the rotovap. Once the temperature stops rising or all liquid is almost completely evaporated, open the injection valve again very slowly so that a small amount of liquid begins to enter the evaporating flask. Do not close injection valve this time but continue to allow solution to enter the evaporating flask. At this point you must try to match the input speed to the output speed. What this means is that you should be injecting the same amount of liquid into the rotovap that is equal to the amount of liquid dripping from the condenser into the receiving flask. You will know that the input speed and output speed are matched because the chiller will remain at a stable temperature. If the chiller begins to rise, then you are injecting too much liquid. Dial back the valve until the chiller stabilizes. Once everything is stabilized, you may walk away from the rotovap if necessary. Check every so often to make sure temperatures remain stable and evaporation continues efficiently. ***Note: All units are inspected for broken glass or parts before unit is shipped. If unit arrives damaged or glass is broken (this does not include minor imperfections or scuffs in glassware), Customer MUST contact BVV™ within 3 days of delivery to file a claim and receive a replacement part. If customer DOES NOT contact BVV™ within 3 days of delivery responsibility for replacement parts falls on the customer and they must pay for replacement pieces.*** ***Note: This item will ship by freight only.*** ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***
$14,750.00 - $17,305.00
10L Premium Short Path Distillation Kit with P10 Distillation Head
10L Short Path Distillation Kit with P10 Distillation Head This unit carries a 2 day lead time. (Note: Stainless Steel Table NOT Included.) The 10L Short Path Distillation Kit features our USA made P10 Distillation Head. Every component in this turnkey is made for precision, throughput, and repeatable results. Also included the Kangaroo digital thermometer which is very rugged and reliable. You will also receive a Ribbed Dewar Style Glass Cold Trap to keep all volatiles and solvents out of your vacuum system. This Kit gives you the basic necessities of a short path distillation system and allows you to add on a temperature control system and vacuum pump to fit your needs. The 10L Neo Kit Includes: 10L Short Path Distillation Kit including glassware, labware, and P10 Distillation Head. 10L Digital Heating and Stirring Mantle. Valved Vacuum Adapter. Ribbed Dewar Style Glass Cold Trap. Kangaroo Digital Thermometer. Distillation Quick Start Guide This guide gives basic quick start instructions for distillation systems. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs, Before beginning distillation, ensure the following steps have been taken: Vacuum Pump is in good working order. Pump should be run against dry load to allow internals to warm up. Oil should be clear. Cloudy or dark oil should be changed. All glass components are in good working order and ready to be assembled A winterization and degassing procedure has been done to prepare oil for distillation The unit's max internal temperature cannot exceed 380C. The recommended max set temperature should not exceed 250C Once all three of these steps have been completed, you are ready to begin distilling. Begin by placing stir bar in boiling flask and then load your material. This should be done using a funnel. A small amount of alcohol in the oil will give it a thinner consistency making it easier to transfer. Assemble all glassware and ensure each joint is properly greased. Do not use too much, as the vacuum pressure might pull some grease into the system. To ensure a full seal, spread grease in a circular motion by rotating glassware Attach circulator to condenser and set temperature to 50C. Allow circulator to reach temperature before beginning distillation. Connect vacuum pump to manifold. The manifold will allow you to isolate each individual component as well as let atmosphere into and out of the system. Connect receiving cow to cold trap. Connect cold trap to manifold. Connect vacuum gauge to manifold. At this point, ensure all connections are correct. Also ensure receiving cow is positioned to collect the first fraction in the far-left receiving flask. Circulator should be at its set temperature. Turn on vacuum pump to begin process. Turn on heat and set to 60C. Vacuum pump will begin to pull down and temperature will begin to rise. Watch the gauge to monitor vacuum pressure and stability. Start stir slower and increase speed with temperature. Once you are close to 60C, increase the temperature 20 degrees. Continue to raise the heat incrementally in 20-degree steps, increasing the set temperature as you near your set point. Increase temperatures incrementally until you reach 220C. You will see your first fraction somewhere between 180C and 190C or slightly before. This is the “heads” fraction. You will move to your second fraction when you see an increased reaction in the head, a slight color change toward golden, as well as a thickening of distillate. When this fraction hits, allow the distillate to “self-clean” the head for a minute or two then, rotate the cow to the middle receiving flask. Collect your “main body” fraction. You will see temps between 190-220C during this fraction. Continue to increase stirring speed as necessary. Reaction in the head may vary but it should never stop. As fluid level in the boiling flask decreases, increase stir speed. The final “tails” fraction is a mixture of the first and second fractions and should be saved for re-distillation later. Ideally, you want to turn the cow to the final flask before the tails fraction hits. The “tails” fraction has an obvious color change and will be darker than the “main body” fraction. You will see temps between 200-250C during this fraction. As fluid level in the boiling flask decreases even more, set stirring RPM higher (1000+ RPM). You may need to compensate with a bit more heat to finish of the final fraction as well. Once process is complete, stop heat, stop stir, and stop vacuum. Let atmosphere into the system. Be sure to properly store your distillate as exposure to air and light can cause oxidation. ***Note: This entire setup will ship via motor freight.*** *Notice to Customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. BVV™ is not responsible for the failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail, which can cause bodily harm or damage to the surrounding area.
$4,100.00
5L Rotary Evaporator 2L Evaporating Flask (2L Flask that is swap able with the RT5L-V2)
This 2L evaporating flask is made out of borosilicate and designed to fit BVV 5L rotary evaporators. Overall length is about 10-3/4".
$105.00
Gas Plug Clear Mix #02
Gas Plug Clear Mix #02 This special Ethanol Blend is a mixture of minerals that electromagnetically affixes themselves to plant compounds and pigment, removing the bad stuff from extracted oil, and purifying your oil Gas Plug Clear Mix #02 SDS CONTAINS: CARBON, SILICA, MAGNESIUM. * DISCLAIMER * You should only lose yield from your oil in correspondence to the amount of residual plant compound removed. If you lose more than 20% yield from gold oil, you have done it wrong. It is not uncommon to have a 50-60% cannabinoid crude oil that loses 30-40% yield under refinement. The amount of yield loss should be proportionate to the overall potency.
$30.00 - $200.00
5L Neocision Short Path Distillation Kit
5L Neocision Short Path Distillation Kit This unit carries a 2 day lead time. The 5L Neocision Short Path Distillation Kit features our 5L Distillation Kit with P5 Distillation Head and USA made glass. Every component in this turnkey is made for precision, throughput, and repeatable results. You will also receive a Dewar Style Glass Cold Trap to keep all volatiles and solvents out of your vacuum system. The Premium Turnkey Kit Includes: 5L Neocision Kit with P5 Distillation Head KF-25 x 1/4" Barb Adapter Dewar Style Glass Cold Trap Distillation Quick Start Guide This guide gives basic quick start instructions for distillation systems. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs, Before beginning distillation, ensure the following steps have been taken: Vacuum Pump is in good working order. Pump should be run against dry load to allow internals to warm up. Oil should be clear. Cloudy or dark oil should be changed. All glass components are in good working order and ready to be assembled A winterization and degassing procedure has been done to prepare oil for distillation Once all three of these steps have been completed, you are ready to begin distilling. Begin by placing stir bar in boiling flask and then load your material. This should be done using a funnel. A small amount of alcohol in the oil will give it a thinner consistency making it easier to transfer. Assemble all glassware and ensure each joint is properly greased. Do not use too much, as the vacuum pressure might pull some grease into the system. To ensure a full seal, spread grease in a circular motion by rotating glassware Attach circulator to condenser and set temperature to 50C. Allow circulator to reach temperature before beginning distillation. Connect vacuum pump to manifold. The manifold will allow you to isolate each individual component as well as let atmosphere into and out of the system. Connect receiving cow to cold trap. Connect cold trap to manifold. Connect vacuum gauge to manifold. At this point, ensure all connections are correct. Also ensure receiving cow is positioned to collect the first fraction in the far-left receiving flask. Circulator should be at its set temperature. Turn on vacuum pump to begin process. Turn on heat and set to 60C. Vacuum pump will begin to pull down and temperature will begin to rise. Watch the gauge to monitor vacuum pressure and stability. Start stir slower and increase speed with temperature. Once you are close to 60C, increase the temperature 20 degrees. Continue to raise the heat incrementally in 20-degree steps, increasing the set temperature as you near your set point. Increase temperatures incrementally until you reach 220C. You will see your first fraction somewhere between 180C and 190C or slightly before. This is the “heads” fraction. You will move to your second fraction when you see an increased reaction in the head, a slight color change toward golden, as well as a thickening of distillate. When this fraction hits, allow the distillate to “self-clean” the head for a minute or two then, rotate the cow to the middle receiving flask. Collect your “main body” fraction. You will see temps between 190-220C during this fraction. Continue to increase stirring speed as necessary. Reaction in the head may vary but it should never stop. As fluid level in the boiling flask decreases, increase stir speed. The final “tails” fraction is a mixture of the first and second fractions and should be saved for re-distillation later. Ideally, you want to turn the cow to the final flask before the tails fraction hits. The “tails” fraction has an obvious color change and will be darker than the “main body” fraction. You will see temps between 200-250C during this fraction. As fluid level in the boiling flask decreases even more, set stirring RPM higher (1000+ RPM). You may need to compensate with a bit more heat to finish of the final fraction as well. Once process is complete, stop heat, stop stir, and stop vacuum. Let atmosphere into the system. Be sure to properly store your distillate as exposure to air and light can cause oxidation. ***Note: This entire setup will ship via motor freight.*** *Notice to Customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. BVV™ is not responsible for the failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail, which can cause bodily harm or damage to the surrounding area.
$6,950.00
Cascade CVO-10 Vacuum Oven
Cascade CVO-10 Vacuum Purge Oven (On Stand) This item carries up to a 1-2 week lead time. Cascade’s Model CVO-10 offers incredible temperature stability for vacuum drying and purging of pharmaceuticals, botanicals, and slurries – especially temperature sensitive material. This vacuum oven liberates solvents, water, and other unwanted compounds. It’s ideal for large batch production environments. Processing Temperature Sensitive Material? The CVO-10 comes in both low temp & high temp versions. Be sure to get the low temp CVO-10 version that has excellent temperature uniformity for products such as pharmaceuticals, slurries or any product that can be damaged or destroyed by temperature fluctuations. CVO-10 Vacuum Oven Features NRTL Certified by TUV 9 sliding, removable shelves that pull out and stay in place for easy load/unload Stable temperature control. Digital temperature readout with temp sensor INSIDE the oven Easy mobility as oven sits on heavy duty industrial cart. Pump sits underneath at base of cart. VITON door gasket Bright LED lights in window for visibility of sensitive material Digital vacuum gauge reads in inches of mercury or torr Smooth, quarter-turn vent valve Rear KF-25 port includes MAX EVAP Connection Kit for rapid vacuum drying or running feedthroughs inside oven for monitoring 220V / 1ph / 10AMPS Quality Tempered Rated Glass NGI-US to ANSI Z97.1.2007 156CFR/201 11 SGCC -2577 ½ UA Ergonomic. Turn vacuum pump on/off from oven control panel Fast Venting with larger ½” diameter vent line Rear vent barb allows for nitrogen or other inert gas connection Touch Panel LED control screen with user settable features The Cascade Difference Vacuum ovens have been around for decades. Basic vacuum ovens are mass-produced and sold by many large laboratory equipment distributors. But there are key differences between Cascade and other less costly, often imported vacuum ovens. Exceptional Temperature Control & Stability The Cascade CVO-10 uses a unique control logic not found in most lab grade vacuum ovens. The temperature probe is INSIDE the oven, which minimizes temperature overshoot and delivers best-in-class temperature stability and uniformity particularly in the low temperature ranges. Accurate, stable temps throughout the CVO-10 eliminate hot and cold spots, making accurate use of every inch of shelf space. Independent Overtemp Failsafe Protection The Cascade Sciences CVO-10 is equipped with a heating cutoff system that will automatically stop power to the heaters when the oven shelf temps exceed 392°F or 200°C. This protection system will provide peace of mind for overnight processing or unattended vacuum bake outs. NRTL Certification #U8 170464972 077. No Extra cost. The CVO-10 Vacuum Oven comes certified by the Nationally Recognized Test Lab, TUV. This certification is a requirement by many municipalities. CAN/CSA-C22.2 No. 61010-1:2012 +UPD No. 1:2015-07 + UPD No. 2:2016-04 CAN/CSA-C22.2 No. 61010-2-010:2015 UL 61010-1:2012/R:2016-04 UL 61010-2-010:2015 EN 61010-1:2010 EN 61010-2-010:2014 Rigorous Quality Assurance in an ISO Certified, USA Manufacturing Facility Cascade Sciences manufactures our ovens in Oregon, USA. We are proud of our ISO 9001 Certification/Accreditation. Each oven completes a series of quality assurance procedures before shipment. Chambers are vacuum tested after welding for vacuum integrity Electrical & mechanical safety is thoroughly tested in compliance with TUV requirements Functional testing verifies user settable items consistent with most lab protocols/usage models Temperature verification includes calibration & temp chamber uniformity following ASTM standards Units are cleaned and packed in ISTA tested, certified packaging materials Digital Vacuum Gauge The digital vacuum gauge installed on the CVO-10 displays in is factory default set to read in inches of mercury (“Hg) or torr. Log Temperature & Vacuum With Data Port The CVO-10 features a rear mounted data port which outputs a digital log line once per minute. Viewing/logging this data requires terminal emulator software such as the open source (BSD License) emulator Tera Term. Equipped for Inert Gas Backfill. Built-In Safety Relief Introduce inert gasses such as nitrogen, argon, helium, etc. as part of your process via the ¼” rear vent barb. The maximum backfill pressure is 15PSI. In an overpressure situation, a simple, built-in safety relief allows gasses to escape via a spring loaded tempered window. Flexible Pumping / Feedthru Connection Ports For faster evaporation, purging or drying the CVO-10 includes Cascade’s MAX EVAP connection kit. The MAX EVAP connection kit secures to the oven’s rear 1” dia KF-25 port located on the back center of the chamber. The MAX EVAP connection never reduces flow by continuing with 1” diameter vacuum rated clear lines, a 1” dia KF-25 side mounted vacuum valve and KF-25 fittings and hardware. This KF-25 port can also be used to run temperature feedthrus, or monitoring sensors inside the vacuum chamber during processing. Ergonomically Designed, Easy Quarter-Turn Valves For anyone that has struggled with consistently turning the small, round, low-quality vacuum/vent valves, relief is in sight. You will love our large, quarter-turn vent valve. Your wrists will thank you! Faster Venting With Large ½” Diameter Vent Lines For large capacity production environments, time is money. The CVO-10 vacuum oven has larger than industry standard vent lines. ½” diameter vent lines means operators spend less time venting the oven. ANSI Rated Tempered Glass + USA Made Steel Cascade ovens are made in Oregon, USA with high quality materials. Our glass is NGI-USA Tempered and certified to ANSI Z97.1.2007 16CFR / 201 11. Our door handles are rugged brushed steel, not plastic. Our vacuum vessels are constructed with American made steel. We’ve tried lower cost, imported steel. But over time, vacuum chambers made of lesser quality/lower tolerance material cannot withstand the flex and pressure changes of vacuum pumping/venting/purging. This can deteriorate vacuum integrity and the oven will lost its ability to hold vacuum. Need A Complete CVO-10 Vacuum Drying or Purge System? Cascade has taken the guesswork out of pairing the right vacuum oven with the proper pump. We offer two complete 10 cubic foot vacuum oven packages that have everything you need to begin vacuum drying on a large scale. The CVO-10 PRO Package pairs the CVO-10 with the clean, quiet, powerful Agilent IDP15 vacuum pump. Purchase the CVO-10 PRO Package and save $1642.86 over retail. The CVO-5 DOUBLE UP Package offers the same 10 cubic foot processing capacity, but in two ovens for smaller, multiple batch management. The TVO-5 DOUBLE UP Package is also self-contained on its own mobile, industrial cart. The TVO-5 DOUBLE UP Package saves $1642.86 over retail. A Vacuum Cold Trap for High Production Environments For high production environments, adding a vacuum cold trap keeps the vacuum pump running optimally, extends time between maintenance and allows reclamation of outgassed materials. Cascade’s MAXTRAP50 is ideally suited for trapping in these high production environments where typical lab grade traps, with small inlets and outlets can slow things down. Specifications Capacity Volume 9.3 Cubic Ft. / 264 Liters Interior 28”W x 24”D x 24”H 711mm x 609mm x 609mm Exterior (Not Including Rack) 44”W x 42”D x 40”H 1118mm x 1067mm x 1016mm 67.6”H with stand Temperature Ranges Low-Temp Processing Range 26°F to 250°F (121°C) Temperature Uniformity +/- 1.5°F @ 105°F (40.5°C) Temperature Stability +/- 0.4°F @ 105°F(40.5°C) Heat Up / Stabilization Time to 250°F 120 minutes (to minimize overshoot) High-Temp CVO-10 (SVAC 9.3) to 428°F / 220°C Available Temperature Uniformity +/- 6.5% of setpoint *Note that ambient laboratory conditions can affect temp performance. Vacuum Valve Type Side Mounted Round Vent Valve Sizes ¼ Turn Lever ½” diameter line Lighting Interior LED Strips (Rated to 150C) On low temp CVO-10 only Window Type Glass Tempered NGI-US to ANSI Z97.1.2007 Vacuum Gauge Indication Reads in inches mercury or torr(Selectable) Temperature Controller Screen Type Touch Screen Accuracy Accurate Within 1°F Failsafe Independent Overtemp Failsafe Ports-Rear Vacuum KF-25 Port Vent 1/2” Barb Data Log temp & vacuum levels Inert Gas Introduction Yes. Via 3/8” Vent Barb 15 psi max inlet pressure Power Options Power 220V – 240V / 1ph / 10A 50/60Hz Cord? Cord Included Outlet Type NEMA 6-15R Power Outlet Shelving Removable? Removable Quantity Included Comes with 9 Each. Fixed. Detail Slide on rails, extend, stay in place. Surface Area 28″W x 24″D Weight Capacity 50 lbs Weight Net Weight 663 lbs / 300.1 Kg Shipping Weight 995 lbs / 351.5 Kg Shipping Details Dimensions 63″L x 60″W x 88″H Class Class 110 Certifications - ISO 9001 - NRTL TUV #U8 170464972 077 - CAN/CSA-C22.2 No. 61010-1:2012 - + UPD No. 1:2015-07 + UPD No. 2:2016-04 - CAN/CSA-C22.2 No. 61010-2-010:2015 - UL 61010-1:2012/R:2016-04 - UL 61010-2-010:2015 - EN 61010-1:2010 - EN 61010-2-010:2014 Warranty Length 1 Year Exclusions Gaskets Not Incuded Dimensional Drawing Download Oven Manual Download DCS Controller Manual View NRTL Certification Contoller Software
$24,997.00
10L Solvent Pro Series Glass Axis
10L Solvent Pro Series Glass Axis. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***
$90.00
10-20L Solvent Pro Rotary Evaporator Bump Trap
10-20L Solvent Pro Rotary Evaporator Bump Trap 10-20L Solvent Pro Rotary Evaporator Bump Trap *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement.
$180.00
20L Solvent Pro Rotary Evaporator Main Condenser
20L Solvent Pro Rotary Evaporator Main Condenser 20L Solvent Pro Rotary Evaporator Main Condenser *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. *Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$400.00
Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 25 Cubic Feet - ETL Rated
Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 25 Cubic Feet - ETL Rated The brand new Neocision ETL Rated 25 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting. Every unit accompanies various safety and protection features taking into consideration user and item safety. These highlights incorporate high and low-temperature alerts. These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. Key Features: ETL Rated Durable Powder Coated Exterior Touch Screen LCD with Datalogging Capabilities Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters (3) 1" ID Ports for putting lines through the freezer Backup battery Included. Specifications Model Number BVV™-86C25 Voltage 115V / 60Hz / 15A Wattage 1800w Capacity 25cu ft. / 730L Internal Dimensions 34.5" x 51.5" x 23.5" Exterior Dimensions 43" x 76" x 36" Temperature Range -40°C to -86°C Weight 700lbs Rating ETL Rated
$9,000.00
Swivel Bosshead
This swivel boss head is made out of die-cast alloy is nickel plated and will fit rod diameters up to 16mm. The boss head can be adjusted and locked to any angle (360°). It is also designed to carry heavy loads and prevent torque damage. Note:Clamps and rods are NOT included.
$14.00
Glas-Col 12L Stir Mantle
Glas-Col 12L Stir Mantle Specifications Body Material Material Max temperature C 400 Height (in) 9 Outside Diameter (od)(in) 16.5 Capacity 12 L Volts 115 Watts 1 @ 1300 Includes: Separable 4-ft., 2-wire cord and locking connector.
$1,788.00
Gas Plug L-5 Bentonite Clay
Purify and prepare your oil with Bentonite Clay ‘L-5’ Gas Plug L-5 Bentonite Clay SDS
$78.00$45.00
J-Kem Gemini-2 Dual Temperature Controller
J-Kem Gemini-2 Dual Temperature Controller Gemini-2 Dual Temperature Controller displays two temperature controllers in a single cabinet to regulate two independent reactions. Each channel is 1200 Watts MAX (1800 Watts total), 15 Amps @ 120VAC, The Gemini is one of J-KEM’s most versatile controllers featuring high power outlets and a 100 hour digital timer (on channel 1) to turn heating OFF (or ON) at a user entered time. Features Included: Over-temperature protection circuits with audible alarms, dual temperature displays, selectable operating modes, double fused, and 100% solid state design. The USB port on the back panel of the controller is an interface to J-KEM’s KEM-Net software. Safety features include: 100% solid state, double fused, audible error alarm, and over temperature circuitry that disconnects power if an over temperature condition occurs. Specifications: Dimensions: 3.5" H x 7.75" W x 8.75" D Power: 15 Amps @ 120VAC, 1200 Watts MAX/Channel, 1800 Watts (Total) Weight: 7 lbs Complete System Includes: One controller Two Teflon thermocouples (12″ long, 1/8″ diameter) Two connecting cords Two 14/20 joint adapters
$1,569.00 - $1,921.00
PolyScience Floating Ball Cover; 3/4" (19 mm) diameter
PolyScience Floating Ball Cover; 3/4" (19 mm) diameter Description Covers top of any open tank. Reduces fumes, splashing hazard and heat loss by 75% and evaporation by 87%. Usable to 95°C. Package of 400 Quantity: 1 pkg Part Number: 060301 For use with: Circulating Baths Stainless Steel Open Bath Systems Polycarbonate Open Bath Systems General Purpose Water Baths
$133.00
Raschig Ring 1LB
Raschig Ring 1LB Raschig rings are pieces of tube used in large numbers as a packed bed within columns for distillation. These glass rings provide a large surface area within the volume of the column for interaction between liquid and gas vapors. Our rings are made from borosilicate glass and are food grade quality. 8mm X 8mm *BVV recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. *BVV is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal.
$120.00
So-Low Flammable Material Storage Refrigerators 1°C to 10°C, 14 Cu.Ft, MV4-6UCFMSR
So-Low Flammable Material Storage Refrigerators 1°C to 10°C, 14 Cu.Ft, MV4-6UCFMSR Please note: This Product may carry up to an 11 week lead time! Our Flammable Refrigerators and Freezers are designed to meet National Fire Protection Agency NFPA and OSHA guidelines for the refrigerated storage of flammable (volatile) material storage in general laboratory work areas. Designed exclusively to control flammable material, The So-Low Flammable Material Storage Freezers and Refrigerators are ideal for storage of any flammable material products. There are no electrical components located in the interior of the unit and the compressor's electrical components have been sealed in a vapor-proof enclosure for additional safety. Units are supplied with a power cord to ease installation. Temperature control and temperature recorder options allow for an individualized intensity of temperature control and monitoring. Adjustable legs and shelves add more availability and storage options to fit your laboratories needs. Features Solid Polyurethane Foam Insulated Doors Epoxy Coated Shelves Adjustable Shelves Adjustable Legs CFC-Free Refrigerant and Insulation Adjustable Thermostat Manual Defrost UL Listed Product Specification Manufacturer So-Low Temperature Range 1°C to 7°C Capacity 6.1 Cufic Feet Exterior w x d x h (inches) 23.625" x 24.25" x 32.187" Exterior w x d x h (cm) 68 x 62 x 82 Door Single Solid, locking Interior Finish Anodized aluminum Leg Four Leveling Legs Insulation Polyurethane foam Refrigerant R134A CFC free Compressor 1/5 hp Condenser Static Defrost Manual Voltage:Domestic 115/60/1 Running Amps/Breaker 2.5/15 Supply Plug 5-15P NEMA UL listed Shipping weight 150lbs Warranty -(Domestic) 12 months parts and labor Compressors additional 4 years, no labor. Specification Data Sheet
$2,160.00
So-Low -85°C Ultra-Low Upright Freezer - 18 Cubic Ft.
So-Low -85°C Ultra-Low Upright Freezer - 18 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! So-Low Ultra-Low Upright Freezers are second to none in low temp applications to suit any laboratory or application needs. These Ultra-Low Temp freezers feature digital temperature control with 2 temperature displays. One shows the set temperature and the other shows the actual temperature in the freezer. The So-Low U85-18 features a battery operated alarm system that will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Product Specifications Temperature Control Digital control with two temperatures displays. one display shows the set temperature, the other shows the actual temperature in the freezer. Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Dimensions: Exterior: 40"" x 36" x 79.5" Interior: 23" x 26" x 51.25" Capacity 18 Cubic Ft. / 505 Liters Temperature Range -40°C to -85°C / -40°F to -121°F Shelving 4 Adjustable Shelves (5 Compartments) Inventory Rack Capacity 20 Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Refrigeration System So-Low cascade type. Two hermetic compressors. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$9,995.00 - $11,544.50
So-Low -80°C Ultra-Low Chest Freezer - 21 Cubic Ft.
So-Low -80°C Ultra-Low Chest Freezer - 21 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! So-Low Ultra-Low Chest Freezers are second to none in low temp applications to suit any laboratory or application needs. These Ultra-Low Temp freezers feature digital temperature control with 2 temperature displays. One shows the set temperature and the other shows the actual temperature in the freezer. The So-Low C80-21 features a battery operated alarm system that will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch Product Specifications Temperature Control Digital Control with two temperature displays. One display shows the set temperature, the other shows the actual temperature in the freezer. Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Dimensions: Exterior: 91" x 36" x 49" Interior: 81" x 21.5" x 21" Capacity 21 Cubic ft. / 594 Liters Temperature Range -40°C to -80°C / -40°F to -112°F Shelving N/A Inventory Rack Capacity 36 Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Refrigeration System So-Low cascade type. Two hermetic compressors. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$12,995.00 - $14,844.50
So-Low -85°C Ultra-Low Chest Freezer - 9 Cubic Ft.
So-Low -85°C Ultra-Low Chest Freezer - 9 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! So-Low Ultra-Low Chest Freezers are second to none in low temp applications to suit any laboratory or application needs. These Ultra-Low Temp freezers feature digital temperature control with 2 temperature displays. One shows the set temperature and the other shows the actual temperature in the freezer. The So-Low C85-9 features a battery operated alarm system that will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Product Specifications Temperature Control Digital Control with two temperature displays. One display shows the set temperature, the other shows the actual temperature in the freezer. Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Dimensions: Exterior: 57.5" x 29" x 46.5" Interior: 46" x 16" x 20" Capacity 9 Cubic Ft. / 255 Liters Temperature Range -40°C to -85°C / -40°F to -121°F Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Refrigeration System So-Low cascade type. Two hermetic compressors. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$7,995.00 - $9,344.50
50L Auxiliary Condenser
Auxiliary condenser for 50L Best Value Rotary Evaporator. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$370.00
5L Solvent Pro Series Glass Axis
5L Solvent Pro Series Glass Axis. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$45.00
10L Solvent Pro Rotary Evaporator Main Condenser
10L Solvent Pro Rotary Evaporator Main Condenser 10L Solvent Pro Rotary Evaporator Main Condenser *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement.
$350.00
CDA 12A w/ Toluene High Purity Extraction Solvent
CDA 12A w/ Toluene HAZMAT ITEMS ARE NON-REFUNDABLE. ALL SALES ARE FINAL (Note: Container style and color may vary) BVV's Ultra High Purity Toluene Denatured Ethanol (CDA 12A) is distinguished by its exceptional purity, Our CDA 12A formulation combines 95% Food Grade/USP/ACS 200 Proof Ethanol, derived from corn, with ~5% high-purity Toluene. Adhering to stringent industry standards, ensuring it meets the precise requirements of our customers, our Ultra High Purity Toluene Denatured Ethanol excels across diverse applications widely adopted as an effective botanical extraction solvent. Being that our Ultra High Purity Denatured Ethanol is made unfit for consumption when denatured with Toluene it is not subject to the Federal Excise Tax on alcohol saving you a huge cost without compromising on it suitability for top-tier extractions. Primarily utilized as pure ethanol in extraction processes, this solvent is favored for its cost-effectiveness and extraction efficiency. Reduce manufacturing costs and increase extraction efficiency with BVV's Ultra High Purity Toluene Denatured Ethanol. Disclaimer: Prices may vary due to market value and for orders of 4 totes or more and a tanker there could be up to a 2 week lead time. Call in for more accurate lead times. Spigots/Faucets are only compatible with 5 Gallon Plastic Jugs and must be purchased separately Trigger Sprayer is only compatible with 1QT and 1 Gallon sizes Key Features: Significantly Reduced Cost due to the absence of Federal Tax Produces Exceptional Quality Extractions Leaves No Residuals or Tastes Evaporates Completely in a Rotary Evaporator Specifications Vapor Pressure: 40.9mmHg at 20°C UN Numbe 1170 Density: 0.7905g/cm³ Specific Gravity 0.7905 Flash Point: 13.9°C (57°F) Boiling Point: 78.5°C (173°F) Melting Point: -90.0°C (-130°F) Chemical Formula: Ethanol C2H6ON-Heptane C7H16 CAS#(s) Ethanol 64-17-5N-Heptane142-82-5 Chemical Formula: Ethanol C2H6ON-Heptane C7H16 Molecular Weight: 72.1057 CAS Registry Number: Ethanol 64-17-5N-Heptane142-82-5 Appearance Colorless Liquid Odor: Mint or acetone-like Density 0.7905g/cm³ Boiling Point: 78.5c/173.3F Solubility in water: Miscible GHS Pictograms: GHS Signal Word: Danger GHS Hazard Statements: H225, H319 GHS Precautionary Statements P210, P233, P240, P241, P242, P243, P261, P264, P271, P280, P303+P361+P353, P304+P340, P305+P351+P338, P312, P337+P313, P370+P378, P403+P233, P403+P235, P405, P501 UN Identification Number: 1987 Proper Shipping Name: Alcohols Transport Hazard Class: 3 Packing Group: I DOT Placard: What is Denatured Ethanol? Denatured ethanol, also known as denatured alcohol, is ethanol (ethyl alcohol) that has been rendered unfit for human consumption by the addition of denaturants. Denaturants are typically chemicals that make the ethanol taste bad or have toxic effects, and they are added to discourage people from drinking the substance. The denaturation process is done to avoid the high taxes and regulations associated with beverage alcohol, as denatured ethanol is intended for industrial, pharmaceutical, or cosmetic uses rather than for consumption. Common denaturants include heptane, methanol, isopropyl alcohol, acetone, and other chemicals. Denatured ethanol is widely used in various industries, such as in the production of paints, solvents, cleaning products, and as a fuel for alcohol burners. Why is Ethanol Denatured? Ethanol is denatured, or rendered undrinkable, for several reasons: Tax Purposes: Denaturing ethanol allows for the imposition of lower taxes on industrial or non-beverage alcohol compared to potable alcohol. Governments often place higher excise taxes on alcohol intended for human consumption. Regulatory Compliance: Denaturing ethanol is a regulatory requirement to discourage the illegal diversion of tax-free industrial alcohol for beverage use. The addition of denaturants makes it unpalatable and unsafe for consumption. Public Safety: Making ethanol undrinkable helps prevent accidental or intentional ingestion of industrial alcohol, which can be toxic. Denaturing agents are chosen to deter people from attempting to use denatured alcohol as a substitute for beverage alcohol. Industrial Use: Denatured ethanol is widely used in various industries, including pharmaceuticals, cosmetics, and manufacturing. It serves as a solvent, fuel, or raw material in these applications. Common denaturants include substances like heptane, methanol, isopropanol, and various chemicals that make the alcohol unsuitable for human consumption while maintaining its usability in industrial processes. The specific denaturing formulations, such as CDA 12-A mentioned earlier, are defined by regulatory agencies to ensure compliance with safety and tax regulations. What is denatured ethanol used for? Denatured ethanol is used for various industrial and commercial purposes where the alcohol is needed for its properties but should not be consumed. Here are some common applications: Industrial Solvent: Denatured ethanol is widely used as a solvent in industries such as pharmaceuticals, cosmetics, and manufacturing. It is effective in dissolving a variety of substances. Cleaning Agent: Due to its solvent properties, denatured ethanol is used as a cleaning agent for surfaces, equipment, and machinery in industrial and commercial settings. Fuel Additive: Denatured ethanol is sometimes used as a fuel additive, especially in the blending of gasoline. It can improve combustion efficiency and reduce emissions. Paint and Coating Industry: It is used as a solvent in the formulation of paints, varnishes, and coatings. Pharmaceuticals: Denatured ethanol is used in the pharmaceutical industry for various purposes, including the extraction of medicinal compounds. Laboratory Use: In laboratories, denatured ethanol is often used for tasks like sterilization and as a solvent for experiments. Inks and Dyes: It is employed in the production of inks and dyes due to its ability to dissolve pigments. Adhesives and Sealants: Denatured ethanol is used in the formulation of adhesives and sealants. Window Cleaning: It is used in commercial window cleaning solutions. Automotive Industry: In the automotive industry, denatured ethanol is used for cleaning and degreasing. What can be used to denature ethanol? Here are examples of common Completely Denatured Alcohol (CDA) formulations used to denature ethanol: CDA 12-A To every 100 gallons of alcohol, add either: Five gallons of n-heptane or 5 gallons of toluene. CDA-19 To every 100 gallons of ethyl alcohol (not less than 160 proof), add: 4.0 gallons of either methyl isobutyl ketone, mixed isomers of nitro propane, or methyln-butyl ketone 1.0 gallon of either kerosene, deodorized kerosene, gasoline, unleaded gasoline, rubber hydrocarbon solvent, or heptane. CDA-20 To every 100 gallons of ethyl alcohol (not less than 195 proof), add a total of: 2.0 gallons of either unleaded gasoline, rubber hydrocarbon solvent, kerosene, or deodorized kerosene, or any combination of these. What does CDA mean? Completely Denatured Alcohol (CDA) is a type of denatured alcohol that has been rendered unfit for human consumption by the addition of denaturing agents. Denatured alcohol is ethanol (ethyl alcohol) that has been intentionally adulterated to make it toxic, foul-tasting, or otherwise undrinkable. This denaturing process is done to exempt the alcohol from excise duty and other taxes, as it's not intended for use in beverages. The denaturing agents used in CDA can vary, but they often include chemicals such as methanol, isopropanol, or other substances that make the alcohol unpalatable and potentially harmful if ingested. The specific formulation of denatured alcohol may be regulated by government authorities to ensure it meets safety standards and legal requirements. CDA is commonly used in industrial applications, as a solvent, fuel, or as a cleaning agent. It's important to note that due to the addition of denaturing agents, CDA should not be used for purposes that involve contact with the human body or ingestion. Safety precautions, including proper ventilation, should be followed when working with denatured alcohol. What is CDA 12A? CDA 12-A is a formulation specified by the Alcohol and Tobacco Tax and Trade Bureau (TTB) for Completely Denatured Alcohol (CDA). The formula is defined under §21.26 as Formula No. 12-A. The composition of CDA 12-A is as follows: For every 100 gallons of alcohol, add either: 5 gallons of n-heptane or 5 gallons of toluene. This denaturing process renders the ethanol unfit for consumption while meeting regulatory requirements for various industrial applications. CDA formulations, including CDA 12-A, are used to denature ethanol for purposes such as industrial solvents, cleaning agents, and manufacturing processes. Can you remove heptane from CDA 12A? When n-Heptane is added to ethanol it creates an azeotrope between the ethanol and n-heptane. An azeotrope is defined as a mixture of two liquids that have a constant boiling point and composition through distillation. This azeotrope results in the ethanol and n-heptane evaporating at the same temperature, making it extremely difficult to separate the two through distillation. While these azeotropic solvents are still easily recovered from a botanical extract at a relatively low boiling point around 78C/173F using a rotary evaporator or falling film evaporator, it is near impossible to separate the two via distillation. What is an Azeotrope? An azeotrope is a mixture characterized by having identical concentrations in both its vapor and liquid phases. This stands in contrast to ideal solutions, where one component is usually more volatile than the other, allowing for separation through distillation. When an azeotrope forms, the concentrations in both phases remain the same, hindering separation through traditional distillation methods. Azeotropes consist of a blend of at least two different liquids, and this mixture can exhibit either a higher or lower boiling point than either of its individual components. Azeotropes become relevant when certain liquid fractions resist alteration through distillation processes. In typical mixtures, components can be extracted using Fractional Distillation, a process involving repeated distillation stages. The more volatile component vaporizes and is collected separately, while the less volatile component remains in the distillation container, resulting in two distinct, pure solutions.
$24.00 - $2,050.00
Neocision ULTRA-Low Upright Style Freezer with Touch Screen LCD (-86°C) 17.3 Cubic Feet - ETL Rated
Neocision ULTRA-Low Upright Style Freezer with Touch Screen LCD (-86°C) 17.3 Cubic Feet - ETL Rated The BVV™ Neocision Freezers offer optimal temperature control conditions to use in laboratories and medical facilities. The freezers have a quiet operating noise of less than 53 decibels. This freezer has a user friendly touch screen that can be used to monitor many different aspects of the internal systems. The screen will display any errors such as temperature faults or power faults. There is a backup battery that will keep the screen operational though a facility power outage, and it will display the internal temperatures. This information can help the user input dry ice or liquid nitrogen to assist in cooling sensitive materials through a prolonged power outage. The internal chamber has 4 sections that can be used individually or the shelves can be removed or adjusted to fit larger items. Features: Backup Battery Data Logging Gasket Heating Locking Handle Vent Port Interior Chamber Probe High Condenser Temperature Alarm Power Failure Alarm Temperature Sensor Failure Alarm Low Battery Alarm High/Low Temperature Alarm Door Alarm Specifications: Model NEO-86L490 Temperature Range (°C) -50 ~ -86 Temperature Uniformity (°C) ≤6 Cooldown time (hours) ≤6 Capacity (ft^3) 17.3 Exterior Dimensions (LxWxH) (in) 35.8 x 36.5 x 78.3 Interior Dimensions (LxWxH) (in) 23.1 x 25 x 51.5 Door Opening (LxH) (in) 23.1 x 51.5 Insulation thickness (in) 5 Interior Material Stainless Steel Door Sections 4 Shelves 3 Levels 4 Refrigerant Type Non HCFC Voltage 220V AC Power 1500 W Weight (lbs) 732
$8,500.00
Neocision ULTRA-Low Upright Style Freezer with Touch Screen LCD (-86°C) 27 Cubic Feet - ETL Rated
Neocision ULTRA-Low Upright Style Freezer with Touch Screen LCD (-86°C) 27 Cubic Feet - ETL Rated The BVV™ Neocision Freezers offer optimal temperature control conditions to use in laboratories and medical facilities. The freezers have a quiet operating noise of less than 53 decibels. This freezer has a user friendly touch screen that can be used to monitor many different aspects of the internal systems. The screen will display any errors such as temperature faults or power faults. There is a backup battery that will keep the screen operational though a facility power outage, and it will display the internal temperatures. This information can help the user input dry ice or liquid nitrogen to assist in cooling sensitive materials through a prolonged power outage. The internal chamber has 4 sections that can be used individually or the shelves can be removed or adjusted to fit larger items. Features: Backup Battery Data Logging Gasket Heating Locking Handle Vent Port Interior Chamber Probe High Condenser Temperature Alarm Power Failure Alarm Temperature Sensor Failure Alarm Low Battery Alarm High/Low Temperature Alarm Door Alarm Specifications: Model NEO-86L770 Temperature Range (°C) -50 ~ -86 Temperature Uniformity (°C) ≤6 Cooldown time (hours) ≤8 Capacity (ft^3) 27 Exterior Dimensions (LxWxH) (in) 43 x 41.5 x 78.3 Interior Dimensions (LxWxH) (in) 30.7 x 29.9 x 51.5 Door Opening (LxH) (in) 30.7 x 51.5 Insulation thickness (in) 5 Interior Material Stainless Steel Door Sections 4 Shelves 3 Levels 4 Refrigerant Type Non HCFC Voltage 220V AC Power 1800 W Weight (lbs) 1080
$10,000.00
Single Neck Cow Distribution Adapter 24/40 Joints
This distribution adapter is used in a short path distillation setup to attach to a single receiving flask and to the vacuum system. The two ground joints are 24/40 to fit the distillation head and receiving flask. The vacuum connection is a GL-14 threaded port.
$160.00$120.00
Glas-Col Mantle and Controller
Glas-Col Mantle and Controller Specifications Material Aluminum Housed Max Temperature C 400 Height (in) 10 Outside Diameter (od)(in) 13.66 Capacity 22L Volts 115 Watts 2 @ 770 Includes: Separable 4-2ft., 2-wire cord and locking connector
$3,253.00
STM RocketBox 2.0
STM RocketBox 2.0 The STM Canna Rocketbox 2.0 is the world’s most advanced commercial pre-roll machine, producing over 453 pre-rolled cones in a 60-second cycle. Designed to maximize pre-rolled joint production while significantly decreasing labor costs, the RocketBox 2.0 is the pinnacle of pre-rolled cone machines. Features 453 Pre-Rolled Joints in 60 Seconds Compatible with 84, 98 and 109 MM Cones Proprietary Smart Density Software to Measure & Achieve Weight Accuracy Variable Frequencies of Vibrations for Even Filling & Packing Built-In Training Mode with Tutorials Adjustable Top Tray for Adjusting Height of Fill Lift Plate to Ensure Cones Sit Flush with One Another Precise, Consistent and Repeatable Results Benefits 6x to 7x's Faster, Decreases Labor for All Size Operations Durable for Long-Term Commercial Use Easy On-Boarding and/or Training After Turnover Density Calculator for Scientifically Accurate Weights Up to 25,000 Joints Daily (grow, scale & co-pack) Attachment-Capable (Sifter Launching 2021) Renowned Training & Support Dedicated STM Client Services Team Exclusive Client Portal with Library of Training Videos and Information What's Included 1 x STM RocketBox 2.0 Pre-Roll Machine 1 x Bottom Tray (in size of choice) 1 x Adjustable Top Tray 1 x Loading Box 1 x Finishing Base 1 x Density Testing Beaker 1 x 12-Month Parts and Labor Warranty RocketBox Comparison Chart RocketBox User Manual RocketBox Brochure RocketBox Technical Specifications
$18,750.00 - $24,950.00
STM Revolution 2.0
STM Revolution 2.0 Designed specifically for flower, the Revolution 2.0 delivers a homogenous, consistent grind, optimal for evenly packed pre-rolls and high-yield extraction. No plastic whips, meat grinders, blenders or flour mills that heat and pulvarize months of your hard work. Chosen by small craft cultivators and start-ups up to the largest brands and facilities around the world, the STM Revolution 2.0 is an asset that grows with your business, allowing your facility to scale as needed and maintain the highest product integrity (retaining your trichomes & terpenes). Features 15-30 LBS Per Hour of Dry Flower Interchangeable Fine & Coarse Particle Screens for Extraction & Pre-Rolls Minimizes Terpene Loss Self-Regulating, Closed-Loop System to Prevent Clogs Auto-Blade Oscillation Creating Scissor-Like Cuts Auger Timing & Blade Speed Control 7%-10% Optimal Moisture Content Consistent and Repeatable Results What's Included Dual Blade System Fine Partical Screen Coarse Particle Screen Cut-Proof Safety Glovews Renowned Training & Support Dedicated STM Client Services Team Exclusive Client Portal with Library of Training Videos and Information Revolution Get Started Revolution User Manual Revolution Comparison Chart Revolution Brochure Revolution Technical Specifications
$17,545.00
STM Mini-RocketBox PLUS+
STM Mini-RocketBox PLUS+ The STM Mini-RocketBox PLUS+ pre-roll machine combines power, efficiency, and versatility to maximize your pre-roll production. Capable of producing 143 pre-rolled cones in under a minute, this machine is perfect for startups on a budget. Features 143 Pre-Rolls in 45 Seconds (4x faster than competitors) Compatible with 84 (.5g), 98 (.7g) and 109 (1g) MM Cones Variable Frequencies of Vibrations for Even Filling & Packing Adjustable Top Tray for Adjusting Height of Fill Lift Plate to Ensure Cones Sit Flush with One Another Fully Adjustable Dial for Desired Tightness & Pack Reduces Tedious Manual Labor Durable Stainless Steel for Commercial & Industrial Use Evenly Fills Cones Layer-by-Layer for Optimal Smokability OSHA Compliant What's Included 1 x STM Mini-RocketBox Pre-Roll Machine 1 x Bottom Tray (in size of choice) 1 x Adjustable Top Tray 1 x Loading Box 1 x Finishing Base 1 x 12-Month Parts and Labor Warranty Renowned Training & Support Dedicated STM Client Services Team Exclusive Client Portal with Library of Training Videos and Information Mini-RocketBox PLUS+ User Manual Mini-RocketBox PLUS+ Technical Specifcations Mini-RocketBox PLUS+ Get Started Mini-RocketBox PLUS+ Brochure Mini-RocketBox PLUS+ Comparison Chart
$6,600.00
STM Mini-Revolution
STM Mini-Revolution Designed specifically for flower, the Mini-Revolution delivers a homogenous, consistent grind, optimal for evenly packed pre-rolls and extraction. Features Variable Speed Control (low, medium, and high) Interchangeable Fine & Coarse Blades Cuts Flower Versus Extruding, Smearing, Pressing, or Whipping Less Terpene Loss Than Competitors Homogenous & Consistent Flower Particles Keeps Stems & Seeds Intact For Easy Post-Sifting Designed, Manufactured & Assembled in the USA Durable, Built for Commercial Use Food-Grade Stainless Steel Construction Quiet Operation OSHA Compliant; Equipped with Safety Switch Very Easy to Clean Tabletop Unit, Ergonomic for Small Production Spaces Renowned Training & Support Dedicated STM Client Services Team Exclusive Client Portal with Library of Training Videos and Information Includes Fine Blade Disc Coarse Blase Disc Collection Bin Mini Revolution Brochure Mini Revolution Comparison Chart Mini Revolution Electrical Schematic Mini Revolution Technical Specifications Mini Revolution User Manual
$6,600.00
STM LaunchPad Weighing Module
STM LaunchPad Weighing Module The First & Only Modular, Commercial Pre-Roll Scale The LaunchPad Weigher is the first and only modular, commercial pre-roll scale which weighs 72-rolls at once and in seconds. The LaunchPad functions as a stand alone machine or better as part of STM Canna’s complete pre-roll workflow system. 72 Rolls Weighed Simultaneously The LaunchPad commercial scale gives your staff the ability to view the weight of each individual pre-roll and identify rejects in an instant with a color-coded display, dramatically increasing production speed and output With this new innovative module, your operation will greatly benefit from reduced labor hours, the ability to maintain precise quality control over the weight of your pre-rolls and maximize profits attributed to under or over filling. Customizable Parameters Target Weight Paper weight % Tolerance View of Min. & Max. Weight by Grams Renowned Service & Support 1-Year Parts & Labor Warranty Dedicated STM Client Services Team Exclusive Client Portal with Library of Training Videos and Information Launchpad User Manual Launchpad Technical Specifications Launchpad Brochure
$35,000.00
STM Atomic Closer 2.0
STM Atomic Closer The only modular pre-roll closing machine on the market designed to incorporate human touch for true premium quality look and feel. Boasting an ultra compact footprint, this one-of-a-kind system can operate on a tabletop in facilities of all sizes, eliminating the industry's #1 pre-roll bottleneck. Features Compatible with RocketBox and Mini-RocketBox. Tamps & Folds Ends into Beautiful, Consistent Crown. Fastest in the Industry at 72 joints every +/- 40 seconds Daily Capacity of 41,000 +/- Pre-Rolls Easy to Clean and Maintain HMI Touch Screen Control Emergency Stop Switch & Reset Button Adaptable to Future Weighing Machine & Packaging Add-Ons Orders are expected to begin shipping in February 2022. Renowned Training & Support Dedicated STM Client Services Team Exclusive Client Portal with Library of Training Videos and Information STM Atomic Closer Brochure PDF Atomic Closer Technical Specifications PDF Atomic Closer User Manual PDF
$49,000.00
Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 16.2 Cubic Feet - ETL Rated
Neocision ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 16.2 Cubic Feet - ETL Rated The brand new Neocision ETL Rated 16.2 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting. Every unit accompanies various safety and protection features taking into consideration user and item safety. These highlights incorporate high and low-temperature alerts. These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. Key Features: ETL Rated Durable Powder Coated Exterior Touch Screen LCD with Datalogging Capabilities Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters (3) 1" ID Ports for putting lines through the freezer Backup battery Included. Specifications Model Number NEO-86C162 Voltage 115V / 60Hz / 13A Wattage 1560w Capacity 16.2cu ft. / 458L / 121G Temperature Range -40°C to -86°C Exterior Dimensions 79-3/4" x 36" x 40" Interior Dimensions 51-1/2" x 23" x 25" Weight 529lbs Certification ETL Rated
$7,500.00
Glas-Col 22L Stir Mantle
Glas-Col 22L Stir Mantle Safely and accurately heat solutions used in various distillations in laboratory and scientific applications Apply heat directly and uniformly to containers, such as round bottom flasks More accurate than hot plates and safer than Bunsen burners Controllers can be purchased individually Accommodates 22L spherical flasks Specifications & Description Max Flask Size (mL) 22000 Min Stirrer Speed (rpm) 100 Max Stirrer Speed (rpm) 1850 Max temperature (° F) 752 Max temperature (° C) 400 Power (VAC) 115 Power (watts) 1540 Height (in) 14 Diameter (in) 6.875 Outside Diameter (OD) (in) 19 Description Stirring/Heating Mantle, 22L Spherical Flask; 115V
$1,900.00
Glas-Col 2 L Stir Mantle
Glas-Col 2 L Stir Mantle Specifications Material aluminum housed Max temperature C 400 Height (in) 6 Outside Diameter (od)(in) 12 Capacity 2 L Volts 115 Watts 500 Includes: Separable 4-ft., 2-wire cord and locking connector.
$1,494.00
P10 BVV™ Distillation Head - USA Made
P10 BVV™ Distillation Head P10 Distillation Head has 2 sets of vigreux in the distillation column with 45/50 lower joint, 24/40 Thermometer Joint, and 34/45 side joint and includes GL-14 barb connections. MADE IN THE USA Designed for 10 Liter Flasks Set of 2 vigreux to allow for more packing media Larger vacuum jacket allows for less heat loss during distillations Larger vapor path to allow for gas/vapor phase flow Increased internal diameter for faster, more efficient fractioning as well as packing and unpacking of media Increased condenser length and diameter for more efficient condensation of vapor with zero clogging *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$800.00
J-KEM® Temperature Controller Model 270
J-KEM® Temperature Controller Model 270 The Temperature Controller Model 270 was design for processes requiring uncompromising safety. The only temperature controller available with a built-in independent backup controller to guard against heating accidents from equipment failure. Features: The desired temperature is entered into the digital display of the setpoint controller which regulates heating. A high temperature limit is then entered into the second digital back-up. If the reaction reaches the setpoint of the second controller, power is shut off from the output circuit until the unit is manually reset. Both controllers independently monior the reaction temperature and in the event that one controller fails, the other takes over to prevent a accident. The USB port on the back panel of the controller is an interface to J-KEM’s KEM-Net software. Specifications: Dimensions: 9.25 × 7.75 × 3.4 in Power: 15 Amps @ 120VAC, 1800 Watts Weight: 7 lbs
$1,728.00 - $1,893.00
Summit Research #29 High Efficiency MONOCOW w/ GL Drain
Summit Research #29 High Efficiency MONOCOW w/ GL Drain Key Features: Direct GL14 drain built in. Designed as a drain for the new series MONOCOWS. Made in USA 100% Schott Summit recommends all users of any and all glassware to operate inside a ventilated fume hood with sufficient blast shields to prevent injury in case of fatigued glass failure. Summit is not responsible or liable for the result of any failures from use, and/or loss of subsequent hardware contamination/failure with or without the result of material loss or damaged caused to surroundings. By purchasing our premiere lines of laboratory glassware the user is responsible to operate in the recommended environment safely. We recommend all users to operate in a legal and licensed facility where safety is the number 1 goal. ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***
$450.00$190.00
So-Low -80°C Platinum Series NU80-30 Ultra-Low Upright Freezer - 31 Cubic Ft.
So-Low -80°C Platinum Series NU80-30 Ultra-Low Upright Freezer - 31 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! Product Specifications Temperature Control Touch Screen Control Displays set point and chamber temperature Hi/Low Alarm Relay Dry Contacts Power Failure Dry Contacts Battery Back-up Viewable Temperature graph Data logging downloadable via USB or FTP Multi-Level Security VNC Remote Access via PC / smart devices Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing feature. Dimensions: Exterior: 60.5" x 37" x 79.5" Interior: 42" x 25" x 51.25" Capacity 31 Cubic Ft. / 877 Liters Temperature Range -40°C to -80°C / -40°F to -112°F Shelving 4 Adjustable Shelves (5 Compartments) Inventory Rack Capacity 30 Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Access Port Mounted in left hand side of the cabinet will be a 1/2" porthole leading into the chilling chamber, complete with plugs. Refrigeration System So-Low cascade type. Two hermetic motor compressors. These compressors are the heavy duty industrial type: air cooled. The motors are sealed in oil for life and have thermoguard overload protection. Compressors start in sequence to protect the unit from overloading. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$16,995.00 - $19,244.50
So-Low -80°C Platinum Series NU80-28 Ultra-Low Upright Freezer - 28 Cubic Ft.
So-Low -80°C Platinum Series NU80-28 Ultra-Low Upright Freezer - 28 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! Product Specifications Temperature Control Touch Screen Control Displays set point and chamber temperature Hi/Low Alarm Relay Dry Contacts Power Failure Dry Contacts Battery Back-up Viewable Temperature graph Data logging downloadable via USB or FTP Multi-Level Security VNC Remote Access via PC / smart devices Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch. Dimensions: Exterior: 54" x 37" x 79.5" Interior: 38" x 25" x 51.25" Capacity 28 Cubic Ft. / 792 Liters Temperature Range -40°C to -80°C / -40°F to -112°F Shelving 4 Adjustable Shelves (5 Compartments) Inventory Rack Capacity 30 Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Access Port Mounted in left hand side of the cabinet will be a 1/2" porthole leading into the chilling chamber, complete with plugs. Refrigeration System So-Low cascade type. Two hermetic compressors. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$16,500.00 - $18,700.00
So-Low -85°C Platinum Series NU85-25 Ultra-Low Upright Freezer - 25 Cubic Ft.
So-Low -85°C Platinum Series NU85-25 Ultra-Low Upright Freezer - 25 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! Manufactured at our facility in Cincinnati Ohio, So-Low Ultra-Low -85°C freezers are produced with high quality craftsmanship, heavy-duty materials, and over 50 years of experience. These freezers use a cascade refrigeration system, providing reliable and durable environmental conditions for your product’s vital temperature requirements. So-Low Ultra-Low freezers are available in wide variety of sizes and styles, to accommodate for each customers required conditions. Combined with our nation-wide service network, our Ultra-Low Freezers have various options for additional temperature recording devices, providing the highest level of quality temperature transcription. Product Specifications Temperature Control Touch Screen Control Displays set point and chamber temperature Hi/Low Alarm Relay Dry Contacts Power Failure Dry Contacts Battery Back-up Viewable Temperature graph Data logging downloadable via USB or FTP Multi-Level Security VNC Remote Access via PC / smart devices Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing feature. Dimensions: Exterior: 50" x 37" x 79.5" Interior: 34" x 25" x 51.25" Capacity 25 Cubic Ft. / 710 Liters Temperature Range -40°C to -85°C / -40°F to -121°F Shelving 4 Adjustable Shelves (5 Compartments) Inventory Rack Capacity 30 Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Access Port Mounted in left hand side of the cabinet will be a 1/2" porthole leading into the chilling chamber, complete with plugs. Refrigeration System So-Low cascade type. Two hermetic motor compressors. These compressors are the heavy duty industrial type: air cooled. The motors are sealed in oil for life and have thermoguard overload protection. Compressors start in sequence to protect the unit from overloading. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$13,700.00 - $15,620.00
So-Low -85°C Platinum Series NU85-22 Ultra-Low Upright Freezer - 22 Cubic Ft.
So-Low -85°C Platinum Series NU85-22 Ultra-Low Upright Freezer - 22 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! Manufactured at our facility in Cincinnati Ohio, So-Low Ultra-Low -85°C freezers are produced with high quality craftsmanship, heavy-duty materials, and over 50 years of experience. These freezers use a cascade refrigeration system, providing reliable and durable environmental conditions for your product’s vital temperature requirements. So-Low Ultra-Low freezers are available in wide variety of sizes and styles, to accommodate for each customers required conditions. Combined with our nation-wide service network, our Ultra-Low Freezers have various options for additional temperature recording devices, providing the highest level of quality temperature transcription. Product Specifications Temperature Control Touch Screen Control Displays set point and chamber temperature Hi/Low Alarm Relay Dry Contacts Power Failure Dry Contacts Battery Back-up Viewable Temperature graph Data logging downloadable via USB or FTP Multi-Level Security VNC Remote Access via PC / smart devices Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing feature. Dimensions: Exterior: 43" x 37" x 79.5" Interior: 28.5" x 26" x 51.25" Capacity 22 Cubic ft. / 626 Liters Temperature Range -40°C to -85°C / -40°F to -121°F Shelving 4 Adjustable Shelves (5 Compartments) Inventory Rack Capacity 25 Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Access Port Mounted in left hand side of the cabinet will be a 1/2" porthole leading into the chilling chamber, complete with plugs. Refrigeration System So-Low cascade type. Two hermetic motor compressors. These compressors are the heavy duty industrial type: air cooled. The motors are sealed in oil for life and have thermoguard overload protection. Compressors start in sequence to protect the unit from overloading. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$12,700.00 - $14,520.00
You have seen 240 out of 254 products