BVV
Enclosed Motor Switch Hazardous-Location - UL Listed / CSA Certified for MVP Recovery Pumps
Enclosed Motor Switch Hazardous-Location - UL Listed / CSA Certified for MVP Recovery Pumps This motor switch is designed for hazardous environments where ignitable gas and dust may be present. They're rated NEMA 7 and 9 for hazardous locations. Use them to turn motors on and off, or with other circuits such as lighting and electric heat circuits. They do not provide overload protection. This item also includes a 1" Male x 3/4" Female NPSM bushing and 1/2" Pipe nipple for steel conduit. Specifications Switch Type Motor Control Reversing Capability Nonreversing Number of Circuits Controlled 2 Electrical Phase (hp) Single (3 hp @ 240 V AC) Switch Starting Position 2 Off (Normally Open) Switch Action Stays Switched (Maintained) Industry Designation DPST-NO Switching: Current 30 A Voltage 600V AC Housing: Material Painted Aluminum Color Gray Height 6.5" Width 3" Depth 4.3" Number of Mounting Holes 2 Mounting Hole Diameter 0.31" Mounting Fasteners Included No Wire Connection Type Screw Terminals Environment Hazardous Location Environment Rating NEMA 7, NEMA 9 Specifications Met UL Listed, CSA Certified RoHS Not Compliant REACH Not Compliant DFARS Specialty Metals COTS-Exempt Country of Origin Mexico
$400.00
EPDM Tri-Clamp Gaskets
EPDM Tri-Clamp Gaskets EPDM Tri-Clamp gaskets are the preferred choice of material for brewing and similar alcohol based applications. EPDM Gaskets offer a low temperature rating and have better physical properties than Viton gaskets; the best part is that they cost less than Viton and provide the same chemical resistance to many alcohols Note: EPDM is not recommended for use with hydrocarbons Key Features: Low temperature range Low costs Better compressibility and springiness Excellent resistance to alcohols Good tear resistance Good abrasion resistance FDA CFR 177.2600 – Rubber and Rubber-Like Material for Repeated Use/Contact with Food. FDA CFR 177.1550 – Fluorocarbon Resins for Repeated Use/Contact With Food, Dairy & Pharmaceutical Products. Sizes Available: 1.5" 2" 3" 4" 6" 8" - easy on flanged 10" - easy on flanged 12" - easy on flanged Technical Specifications: Material EPDM Color Black Connection Type Tri-Clamp Conformance FDA Compliant / Meets 3A Standards Thermal Properties: -Low Temperature Range -55°F -Minimum for Continuous Use (Static) -40°F -Brittle Point -55°F -High Temperature Range +275°F -Maximum for Continuous Use (Static) +275°F Gas Permeability Excellent Durometer or Hardness Range 65 Shore A Tensile Strength Range 200-3500PSI Elongation Range (%) 350-650% Abrasion Resistance Excellent Tear Resistance Excellent Resilience / Rebound Good Thread Style Female Chemical Compatibility: Butane D - Severe Effect Propane (liquified) D - Severe Effect Alcohols: -Amyl A - Excellent -Benzyl B - Good -Butyl B - Good -Diacetone A - Excellent -Ethyl A - Excellent -Hexyl C - Fair -Isobutyl A - Excellent -Isopropyl A - Excellent -Isopropyl A - Excellent -Methyl A - Excellent -Octyl C - Fair -Propyl A - Excellent No more than a -40 F operating temperature should be used with EPDM. BVV is not responsible if incompatible chemicals, solvents, or operating temperatures are used in the user's system.
$1.00 - $51.00
Ethanol 200 Proof, SDA 3C (100% ABV) Lab Grade
BVV™ Ethanol 200 Proof, SDA 3C Contains: Isopropyl Alcohol ~4.69% 100% AVB (alcohol by volume) HAZMAT ITEMS ARE NON-REFUNDABLE. ALL SALES ARE FINAL Specially Denatured Alcohol, 3C is a mixture of 200 proof grain ethanol mixed with just under 5% isopropyl alcohol. Its laboratory grade and is used for scientific applications, perfume, reagent/solvent, personal care products, and research and as and as a fuel for certain types of lamps and burners. The term "200 proof" refers to the alcohol's strength, which is equivalent to 100% alcohol by volume (ABV). This means that there is no water or other substances present in the alcohol, making it very pure and highly concentrated. Ethanol 200 Proof, SDA 3C Certificate of Analysis (COA) Ethanol 200 Proof, SDA 3C Safety Data Sheet (SDS) Chemical Formula: C2H5OH Molecular Weight: 46.069 CAS Registry Number: Ethanol 64-17-5 Isopropyl Alcohol 67-63-0 Appearance Colorless Liquid Odor: wine-like, pungent Density 0.78945 g/cm3 @ 20 °C Boiling Point: 78.23C/172.81F Solubility in water: Miscible GHS Pictograms: GHS Signal Word: Danger GHS Hazard Statements: H225, H319, H360D GHS Precautionary Statements P210, P233, P240, P241, P242, P305+P351+P338 UN Identification Number: 1170 Proper Shipping Name: Ethanol Transport Hazard Class: 3 Packing Group: II DOT Placard:
$18.00 - $2,300.00
Ethanol 200 Proof, SDA 40B (100% ABV) Lab Grade
BVV™ Ethanol 200 Proof, SDA 40B 100% AVB (alcohol by volume) HAZMAT ITEMS ARE NON-REFUNDABLE. ALL SALES ARE FINAL Specially denatured alcohol formula 40B, contains trace amounts (less than 0.125% combined) of the denaturants tert-butyl alcohol and denatonium benzoate, compliant with United States Title 27 of the Code of Federal Regulations, Section 21.151. SDA-40B denatured ethanol is a popular choice for cosmetic applications because studies have shown low toxicity in topical applications. It is very popular in perfumes and colognes, earning the nickname of perfumer's alcohol. It is also often used as the alcohol component to hand sanitizers. The high solvency power of SDA 40B 200 proof lends to ideal use in the production of inks, adhesives and coatings. The term "200 proof" refers to the alcohol's strength, which is equivalent to 100% alcohol by volume (ABV). This means that there is no water or other substances present in the alcohol, making it very pure and highly concentrated.
$18.00 - $3,150.00
Ethanol Dehydration Sieve Beads Type 3A
Ethanol Dehydration Sieve Beads Type 3A Ethanol Dehydration Beads Type 3A is specifically designed for the dehydration of fuel grade ethanol. Ethanol can only be dried to an azeotropic point of 95.6% purity by traditional distillation. After that point, 3A selectively adsorbs the water from the solution to produce anhydrous ethanol with less than 0.5% water. This is the drying method of choice for fuel ethanol producers. With these beads you can remove water to achieve a metered proof of 200 or 99.999%. Chemical Formula: K12[(AlO2)12(SiO2)12] · nH2O. Typical Applications: Ethanol Dehydration Grade Molecular Sieve products (sieve beads) are typically used for the dehydration of fuel grade ethanol PSA and VSA systems. Available Products Ethanol Dehydration Grade Molecular Sieve: Product Adsorbent Type Size Form 3A EDG Molecular Sieve 3A 4 x 8 Mesh Beads Handling & Storage Recommendations: Store in a dry location to prevent unintentional water adsorption. Reseal packages after opening to prevent contamination and unintentional water adsorption. We recommend that you rotate stock so the oldest material is used first. Please read the safety data sheet to ensure proper handling and always wear personal protection equipment when handling molecular sieve. Product Data and Safety Information: Molecular Sieve 3A Technical Data Sheet Molecular Sieve 3A Safety Data Sheet Note: 20lb size comes as set of 2x 10lb containers. Size Recommendations: 2LB - Will fit our Molecular Sieve Filter Drier 4LB - Will fit our XL Molecular Sieve Filter Drier 6LB - Will fit our 30LB Extractor
$20.00 - $1,690.00
Ethyl Acetate Tech Grade 99.8%
Ethyl Acetate Tech Grade 99.8% C4H8O2 Ethyl acetate is a widely used solvent. Ethyl acetate is the acetate ester formed between acetic acid and ethanol. It has a role as a polar aprotic solvent. Ethyl acetate appears as a clear colorless liquid with a fruity odor. Its flash point is 24 °F and is less dense than water. It's vapors are heavier than air. Ethyl acetate is a common solvent for column and thin-layer chromatography. It is also used as a defatting agent for extraction and can be used to extract oil from organic materials. Ethyl acetate is commonly used to extract oil from coffee. Ethyl acetate is an organic solvent that is volatile and flammable. Chemical Formula: C4H8O2 Molecular Weight: 88.106 CAS Registry Number: 141-78-6 Appearance Colorless Liquid Odor: nail polish-like, fruity Density 0.902 g/cm3 Boiling Point: 77.1C/170.8F Solubility in water: 8.3 g/100 mL (at 20 °C) GHS Pictograms: GHS Signal Word: Danger GHS Hazard Statements: H225, H319, H336 GHS Precautionary Statements P210, P233, P240, P305+P351+P338, P403+P235 UN Identification Number: 1173 Proper Shipping Name: Ethyl Acetate Transport Hazard Class: 3 Packing Group: II DOT Placard: How Is Ethyl Acetate Produced? Ethyl acetate is primarily produced through the esterification reaction between ethanol (ethyl alcohol) and acetic acid. This reaction typically takes place in the presence of an acid catalyst, such as sulfuric acid or strong acidic ion exchange resins. The production process can be summarized as follows: Preparation of Ethanol: Ethanol, the primary raw material for ethyl acetate production, is typically produced through fermentation of biomass, such as grains, sugarcane, or corn, followed by distillation to obtain high-purity ethanol. Preparation of Acetic Acid: Acetic acid, another key raw material for ethyl acetate production, can be produced through various methods, including oxidation of acetaldehyde, methanol carbonylation, or direct synthesis from natural gas or biomass. Esterification Reaction: In the esterification reaction, ethanol and acetic acid are mixed together in the presence of an acid catalyst. The acid catalyst helps facilitate the reaction by providing a suitable environment for the formation of the ester bond. The esterification reaction can be represented by the following chemical equation: Ethanol + Acetic Acid ⇌ Ethyl Acetate + Water Separation and Purification: After the esterification reaction, the mixture typically undergoes separation and purification steps to isolate ethyl acetate from other reaction byproducts and unreacted starting materials. This may involve distillation, extraction, or other separation techniques to obtain pure ethyl acetate. Recovery and Recycling: Any unreacted ethanol or acetic acid, as well as other byproducts, are usually recovered from the process stream and recycled back into the production process to improve efficiency and minimize waste. The production of ethyl acetate can be carried out in batch or continuous processes, depending on the scale and requirements of the production facility. The process may also vary depending on factors such as the choice of catalyst, reaction conditions, and purification methods. Overall, ethyl acetate is a widely used solvent with applications in industries such as coatings, adhesives, pharmaceuticals, and flavorings. What Is Ethyl Acetate Used For? Ethyl acetate is a versatile solvent with a wide range of industrial, commercial, and laboratory applications. Some common uses of ethyl acetate include: Paints and Coatings: Ethyl acetate is commonly used as a solvent in the formulation of paints, varnishes, lacquers, and other coatings. It helps dissolve resins, pigments, and binders, allowing for proper application and drying of the coatings. Adhesives and Sealants: Ethyl acetate is utilized as a solvent in the production of adhesives and sealants, particularly those used in woodworking, construction, and automotive industries. Printing Inks: Ethyl acetate is a key component in the formulation of printing inks for various printing processes, including flexographic, gravure, and screen printing. It helps dissolve the ink pigments and other additives, ensuring proper printing quality and performance. Pharmaceuticals: Ethyl acetate is used in pharmaceutical manufacturing processes as a solvent for extracting and purifying natural products, synthesizing pharmaceutical compounds, and formulating dosage forms such as tablets and capsules. Flavors and Fragrances: Ethyl acetate is employed in the production of flavors and fragrances for use in food, beverages, cosmetics, and personal care products. It serves as a solvent for extracting and concentrating natural flavors and essential oils. Nail Polish and Nail Polish Removers: Ethyl acetate is a common ingredient in nail polish formulations and nail polish removers. It helps dissolve the resins and pigments in nail polish and effectively removes nail polish from nails. Cleaners and Degreasers: Ethyl acetate is used as a solvent in cleaning products, degreasers, and surface coatings for removing grease, oil, and other contaminants from surfaces and equipment. Analytical Chemistry: Ethyl acetate is frequently used as a solvent in analytical chemistry techniques such as liquid-liquid extraction, chromatography, and sample preparation for gas chromatography. Extraction of Natural Products: Ethyl acetate is used in the extraction of natural products from plants, herbs, and botanicals due to its ability to selectively dissolve certain compounds while leaving others behind. These are just a few examples of the diverse range of applications for ethyl acetate. Its versatility, low toxicity, and pleasant odor make it a popular choice for various industrial and commercial uses. However, it's important to handle ethyl acetate with care, as it is flammable and may pose health risks if not used properly. What Are The Hazards of Ethyl Acetate? While ethyl acetate is generally considered to have low toxicity compared to many other organic solvents, it still poses some hazards that should be taken into consideration, especially when handling it in industrial or laboratory settings. Some of the hazards associated with ethyl acetate include: Flammability: Ethyl acetate is highly flammable and can form explosive mixtures with air. It has a low flash point and can ignite easily in the presence of a spark, flame, or heat source. Proper precautions, such as storing ethyl acetate in tightly sealed containers away from ignition sources and ensuring adequate ventilation to prevent the buildup of flammable vapors, are necessary to minimize the risk of fire and explosions. Health Effects: While ethyl acetate is considered to have low acute toxicity, exposure to high concentrations of vapors or prolonged exposure may cause irritation to the eyes, nose, and throat. Inhaling ethyl acetate vapors in large quantities may also cause dizziness, headaches, nausea, and central nervous system depression. Skin contact with ethyl acetate may result in irritation or dermatitis. Individuals with pre-existing respiratory conditions or sensitivities may be more susceptible to the effects of ethyl acetate exposure. Environmental Impact: Ethyl acetate can have adverse effects on the environment if released into the air, water, or soil. It is volatile and can evaporate quickly from spills or during use, contributing to air pollution. Ethyl acetate may also pose a risk to aquatic organisms if it contaminates water bodies. Proper handling, storage, and disposal practices are necessary to prevent environmental contamination. Reproductive and Developmental Effects: Some studies have suggested that exposure to high concentrations of ethyl acetate may have adverse effects on reproductive health and fetal development. Pregnant women exposed to ethyl acetate vapors should take precautions to minimize exposure to protect both their health and the health of the developing fetus. Sensitization: Prolonged or repeated exposure to ethyl acetate may lead to sensitization reactions in some individuals, resulting in allergic reactions upon subsequent exposure. It's important to follow safety guidelines and regulations when handling ethyl acetate to minimize risks to human health and the environment. This includes using appropriate personal protective equipment (such as gloves, goggles, and respiratory protection), ensuring adequate ventilation in work areas, and implementing proper storage and disposal practices. Training on safe handling procedures and emergency response protocols should also be provided to personnel working with ethyl acetate.
$20.00 - $740.00
Explosion Proof Platform Scales - 3000KG
These Explosion proof platform scales come with a ramp and can handle a maximum load of 3000KG. Scale measurement: 1200MM X 1200MM (47.24" x 47.24") Scale height: 110mm (4.33") Scale weight: 83KG (182.984LBS) Note: This scale only measures in KG
$1,850.00 - $2,250.00
Express Extractor Heater 3.5 to 11KW of heating Power!
Express Extractor Heater by BVV™ 1 Year Warranty, Built in house ready to ship in 24hrs! The BVV™ Extractor Heater is our built in house high power extractor heater circulator. We have 3 model units 3,500, 8,000 & 11,000 WATTS! Each upright panel comes with 25ft of silicone tubing and a 5 gallon reservoir. Each system is capable of heating up to 140°F and can exceed the demand of even the largest extraction vessels. The system operates on an independent nitrile diaphragm pump circulating water @1.5GPM. The pump can self prime up to 11ft. and within a typical extractor this pump is operating around 30-50psi in circulating pressure. BVV Part# KW AMPS Voltage Breaker AMPS Installed Plug Rec. Wire Size Temp. Range EEH-3.5KW 3.5 29 120V (1x30)A L5-30P Plug 10 AWG 120°F EEH-8KW 7.3 33 240V (1x40)A 6-50P 8 AWG 80-140°F (adjustable) EEH-11KW 11 46 240V (2x30)A 6-30P (2x12) AWG 80-140°F (adjustable) EEH-5.5KW 5.5 25 220V (1X25)A 6-30P 10 AWG The 3.5KW unit has a digital temperature display and cannot be adjusted from the standard factory programmed 120°F. During normal recovery operations used with our extractors this fluctuates between 120-157°F. Though there is a lack in temperature accuracy we measure at the extractor base a consistent recovery temperature around 122-125°F. These heater are built with an electrical failsafe that prevents them from operating dry, and will auto shut down if the flow is unexpectedly stopped to protect the unit. The attached in-line filter will prevent any debris from entering the heater. A clogged filter will also prevent the heater from operating. General Extractor Size Heater Recommendations for these Models 0-2lbs Biomass EEH-3.5KW 2-5lbs Biomass EEH-8KW 5-20lbs Biomass EEH-11KW At BVV our favorite model is the 11KW. The unit does require two 240V 30A Single phase circuits, but its now a permanent fixture in or laboratory. Every model will pump out lots of heat for any recovery situation, could you use a 3.5KW heater on a 5 or 10lb unit? Absolutely, Just expect longer times to reach the heaters maximum setting. For example we heated 3x 6"x48" fully jacketed columns to 140°F (heater temp) in about 11 minutes using the 11KW heater. Another example is a 1lb Apollo extractor with a fully jacketed collection base heated to 120°F in about 8-9 min. using the 3.5KW extractor heater. ETL Listed to UL 499 and CSA (Canada) Utilizing all UL approved components for the heater, pump, and emergency stop switches, wiring harnesses, plugs, and electrical housings. The heater arrive with the specified plugs attached, however all of the models can be hardwired directly if you choose not to use a plug. *240V units can be used on 208V single phase with 25% reduced temperature output Express Extractor Heater Quick Start Guide
$1,075.00 - $1,375.00
Extractor Column Bolt-On Handles fits Tri-Clamp Tubing
Extractor Column Bolt-On Handles For Tri-Clamp Pipes, Tubing, Dewaxing Columns, or Collection Bases! (Does Not Include Pictured Jacketed Tri-Clamp Splatter Platter) These Bolt-On Stainless Steel Pipe Hangers have welded on handles to allow for easier handling of stainless steel spools, splatter platters, and collection bases to pour out extracts, dry ice, or anything else with ease. Please note that when ordering a specific size for a dewaxing or jacketed column to measure the outer diameter because it will be larger than the actual 'Tri-Clamp' size.
$13.00 - $56.00
Extractor Dispensing Wand with Toggle Valve - USA SSP Valve
Extractor Dispensing Wand with Toggle Valve This Dispersing Wand is used for dispensing out extracted material without having to lift a heavy collection base and is a lot more controllable when spreading it across a sheet. The valve is a 316L stainless steel compression fitting toggle valve with 3/8" JIC flare and 3/8" diameter x 7" long angled dispersing tube.
$285.00
Extractor Material Packing Rod
Extractor Material Packing Rod This affordable and economic tool is throwback to the old days in the BVV lab. This is what we used then and we still use now. Never released for sale until now, we decided we think everyone will like them as much as we do. Simple and sturdy this tool will last as long as ours have; 7 years and more! Constructed of an aluminum shaft with a fixed stainless steel end plate, plastic guard, and stainless hardware. The packing rod is light weight and the added guard makes for a non-scratching design. The best feature is that it will fit the column with a small gap around the circumference and makes packing quick work. Available in 24" and 36" rods. They are not designed to be extendable so if you needed a longer size just send us an email to support@shopbvv.com and we can send you a price quote. For a full stainless steel professional grade packing rod check out this BVV item Stainless Steel Extractor Packing Rod SKU# PROD15024
$26.00 - $44.00
Fast-Acting Panel-Mount On/Off Valve
Fast-Acting Panel-Mount On/Off Valve Open and close these valves with the flip of the toggle switch. Commonly used for equipment testing and gas sampling, they have threads and a hex nut below the handle for installation in instrument panels. 316 stainless steel valves are more corrosion-resistant than brass valves. Manual-return valves remain open or closed when the toggle is moved into position. Spring-return valves automatically close when the toggle is released. Flow coefficient (Cv) is the amount of water (in gallons per minute) at 60° F that will flow through a fully open valve with a difference of 1 psi between the inlet and the outlet. Pipe Size Flow Coefficient (Cv) Max. Pressure Temperature RangeDegrees F Toggle Switch Type End-to-EndLg Panel Cutout Dia 1/4 .2 300 psi @ 200 degrees F -20 degrees to 200 degrees Manual Return 2 1/4" 17/32"
$95.00
Female Joint Stopper - 24/40
Female Joint Stopper - 24/40 This glass stopper features a cap design and a ground interchangeable taper outer joint, perfectly suited to fit a 24/40 ground inner joint. The frosted, precision-ground glass surfaces ensure a tight seal when properly greased, providing reliability and security for your laboratory needs. The female joint's taper allows it to seamlessly fit any glassware with a male joint of the same taper and outside diameter, as long as there is no interference with the attached apparatus.Crafted from high-quality borosilicate glass 3.3 using hand-blowing techniques, our joint stopper ensures durability and resilience. The heavy-wall design of the glass tubing used in its construction further enhances its strength and longevity, making it a reliable choice for your laboratory experiments and applications. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$5.00
Female NPT Shower Head End Caps
Female NPT Shower Head End Caps Shower Head End Caps Tri Clamp/ Tri Clover help disperse solvent input into a system which creates better material saturation when flooding a material column. This helps to prevent channeling, ensuring all the material is saturated. Specifications: Material: 304 Stainless Steel Connection Type: Tri-Clamp 1/4" - 18 FNPT 3/8" -18 FNPT 1/2" - 14 FNPT Standard: 3A Sizes Available: 1.5" 2" 3" 4" 6"
$30.00 - $62.00
Female Tee
BVV™ Female Tee BVV™ brand stainless steel parts are made with precision 304 Grade Stainless Steel and are clean and free from burrs or debris. These fittings are NPT threads (National Pipe Taper) and will compress against other Female/Male NPT threads creating a tighter and tighter connection. All NPT threads require thread sealant to create a watertight and gas-tight seal between the threads. We recommend using Yellow Gas PTFE Tape because it is rated for gases and is UL listed and it is NOT recommended to use white PTFE tape because it is not rated for gas service. Stainless Steel Female Tees are used to connect 3 Male NPT threaded connections together for either diverting flow in a system or even isolating a section of the extraction system. BVV™ Female Tee - Data Sheet Specifications Material 304 Stainless Steel Connection Type(s): 1/4"-18 FNPT 3/8"-18 FNPT Sizes Available: 1/4" 3/8"
$20.00 - $40.00
Fiberglass Insulation Rope 10 Feet
Fiberglass Insulation Rope 10 Feet ***Caution: Always use proper protection when working with fiberglass. Avoid skin and eye contact.*** Ten feet of white 1/2" fiberglass insulation rope. Used to wrap the upper half of boiling flasks. Specifications: Width: 1/2" Material: Fiberglass Maximum Temperature: 1000F Resistant to solvents, acids, and bleach Color: White Length: 10 ft. (20ft needed for 5L Flask.)
$28.00
Filter Bag for Petroleum Oil and Organic Solvents
These filter bags come in a wide variety of micron levels and are specifically designed for BVV Pressure Filtration Systems. They are made of nylon fabric and range from 1 micron to 100 micron. For use with the following systems: Cryogenic 45L Centrifuge Extractor Kit Pressure Filtration System - 6 x 28 *Note: metal mesh cage not included - for reference only.
$59.00
Filter Plate Kit
Stainless Steel Tri-Clamp / Tri Clover Filter Plate Kit Stainless steel filter plates kits offer the user a great solid platform to help with filtration during the extraction process and they come standard with a 100 mesh (150 Micron) pre-cut stainless steel mesh filter media, solid filter ring, and gasket. These filter plates can be used simultaneously with ashless filter papers or any other filtration media like stainless steel ball bearings or steel wool to increase surface and filtration level to remove fats, lipids, waxes and any other unwanted material during the extraction process. Note: 2" and 8" Sizes come with a Compression ring instead of a solid ring. Sizes Available: 1.5" - Includes Solid Filter Plate Ring 2" - Includes Solid Filter Plate Ring 3" - Includes Solid Filter Plate Ring 4" - Includes Solid Filter Plate Ring 6" - Includes Solid Filter Plate Ring 8" - Includes High Pressure Clamp + Includes Standard COMPRESSION Ring ONLY 10" - Includes High Pressure Clamp + Solid Filter Plate Ring ONLY 12" - Includes High Pressure Clamp + Solid Filter Plate Ring ONLY Specifications: Material 304 Stainless Steel Standard 3A High Polish Connection Type(s) Tri-Clamp Hole Diameter 5.8mm Height 2" Mesh Specs 100 Mesh (150 Micron) - 304 Stainless Steel Gasket Material BUNA-N
$38.00 - $491.00
Filter Plate Ring
Filter Plate Ring *Note: Only 1 Ring Included per Order. Increase Quantity for more Rings. These filter plate rings allow the user to stack different levels of filtration inside their system. They are made out of 304 stainless steel and will easily drop inside of any Tri-Clamp/ Tri Clover column or filter plate.
$12.00 - $48.00
Filter Plate with Built-In Sintered Disk
Filter Plate with Built-In Sintered Disk / Tri Clover Filter Plate These filter plates offer the user a great solid platform to help with filtration during the extraction process with a welded in sintered filter disk with hexagon backing. These filter plates can be used simultaneously with ashless filter papers or any other filtration media like stainless steel ball bearings or steel wool to increase surface and filtration level to remove fats, lipids, waxes and any other unwanted material during the extraction process. **Note: Does not include Clamp or Gasket Sizes Available: 1.5" 2" 3" 4" 6" 8" 10" 12" Specifications: Material 304 Stainless Steel Standard 3A High Polish Connection Type(s) Tri-Clamp Hole Diameter 5.8mm Height 2"
$73.00 - $600.00
FJIC X 3MM Can Adapter
FJIC X 3MM Can Adapter This adapter allows the user to seamlessly inject canned solvent into a standard 1/4" MJIC connection without releasing solvent to the atmosphere. This FJIC to 3MM adapter conveniently screws onto any 1/4" MJIC connection allowing for the safe injection of canned solvent into a closed loop system.
$35.00 - $37.00
FKM Viton Tri-Clamp Gaskets
FKM Viton Tri-Clamp Gaskets Fluoroelastomer (FKM) gaskets are a great option for using higher temperatures in a closed-loop system or other steps of the extraction process including filtration and decarbing. FKM offers an excellent chemical compatibility with numerous solvents. FKM Gaskets offer a higher temperature rating and better chemical compatibility than Buna rubber. Key Features: High-temperature range Better compressibility and springiness Excellent resistance to butane and propane Better tear resistance Better chemical resistance USP Certified FDA CFR 177.2600 – Rubber and Rubber-Like Material for Repeated Use/Contact with Food. FDA CFR 177.1550 – Fluorocarbon Resins for Repeated Use/Contact With Food, Dairy & Pharmaceutical Products. Sizes Available: 1.5" 2" 3" 4" 6" 8" - easy on flanged 10" - easy on flanged 12" - easy on flanged Technical Specifications: Material: Viton (FKM) Color: Black Connection Type: Tri-Clamps Conformance: FDA Compliant / Meets 3A Standards Thermal Properties: -Low Temperature Range -49°F -Minimum For Continuous Use (Static) -15°F -Brittle Point -49°F -High Temperature Range +400°F -Maximum for Continuous Use (Static) +400°F Gas Permeability: Excellent Chemical Compatibility: Butane A - Excellent Propane (liquified) A - Excellent Alcohols: -Amyl A - Excellent -Benzyl A - Excellent -Butyl A - Excellent -Diacetone D - Severe Effect -Ethyl A - Excellent -Hexyl C - Fair -Isobutyl B - Good -Isopropyl A - Excellent -Isopropyl A - Excellent -Methyl C - Fair -Octyl B - Good -Propyl A - Excellent BVV is not responsible if incompatible chemicals, solvents, or operating temperatures are used in the user's system.
$3.00 - $80.00
Flask Tongs
Flask Tongs These flask tongs are great when handling any glassware that is too hot to handle or off-gassing and allows the user to handle the flask or beaker at a safe distance with ease. These tongs are a 2 finger design with nickel plated metal and rubber coated fingers with an overall length of 10.5".
$6.00
Flat Bottom Flask
Flat Bottom Flask Flat Bottom Flasks are used to capture and store material when used with a glass funnel. These flasks are flat bottomed and come with a non-jointed opening. Sizes Available: 500ml 1000ml *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$15.00 - $17.00
Flat Tri-Clamp Reducer
Flat Tri-Clamp/Tri-Clover Reducers Flat Tri-Clamp reducers allow the user to connect differently sized Tri-Clamp parts to each other without adding to the overall size of your extraction system. These reducers are offered in Tri-clamp x Tri-Clamp connections Sanitary Fittings end cap reducers are often used as an increaser flowing from smaller to a larger diameter which makes them suitable in horizontal flow applications, available in eleven sizes. Specifications: Material: 304 Stainless Steel High Polish Interior Standard: 3A Connection Type : Tri-Clamp x Tri-Clamp
$20.00 - $125.00
Flexible Rubber Foam Pipe Insulation Elbow, 1/2" Thick Wall, 1-3/8" ID
Flexible Rubber Foam Pipe Insulation Elbow Soft and easy to install, this insulation restricts absorption of water, air, and gas. It is often used on cold and hot water lines and refrigeration lines. Seal with contact adhesive (sold separately). To use outdoors, coat in acrylic paint. For Use On Pipe Insulation Type Elbow Elbow Bend 90° Wall Thickness 1/2" ID 1 3/8" OD 2 3/8" For Pipe Size 1 For Copper Tube Size 1 1/4 Temperature Range -295° to 220° F Heat Flow Rate 0.25 Btu @ 75° F Density 4.5 lbs./cu. ft. Material Buna-N/PVC Foam Color Black Flexibility Flexible Cell Type Closed Tube Style Slit Specifications Met ASTM E84 25/50 for Flame and Smoke, ASTM C534 Performance Properties Moisture Resistant R Value 2 Additional Specifications SDS RoHS RoHS 3 (2015/863/EU) Compliant REACH REACH (EC 1907/2006) (01/17/2022, 223 SVHC) Compliant DFARS Specialty Metals COTS-Exempt Country of Origin United States USMCA Qualifying No Schedule B 392690.9988 ECCN EAR99
$11.50
Flexible Rubber Foam Pipe Insulation Tee, 1/2" Thick Wall, 1-3/8" ID
Flexible Rubber Foam Pipe Insulation Tee Soft and easy to install, this insulation restricts absorption of water, air, and gas. It is often used on cold and hot water lines and refrigeration lines. Seal with contact adhesive (sold separately). To use outdoors, coat in acrylic paint. For Use On Pipe Insulation Type Tee Wall Thickness 1/2" ID 1 3/8" OD 2 3/8" For Pipe Size 1 For Copper Tube Size 1 1/4 Temperature Range -295° to 220° F Heat Flow Rate 0.25 Btu @ 75° F Density 4.5 lbs./cu. ft. Material Buna-N/PVC Foam Color Black Flexibility Flexible Cell Type Closed Tube Style Slit Specifications Met ASTM E84 25/50 for Flame and Smoke, ASTM C534 Performance Properties Moisture Resistant R Value 2 Additional Specifications SDS RoHS RoHS 3 (2015/863/EU) Compliant REACH REACH (EC 1907/2006) (01/17/2022, 223 SVHC) Compliant DFARS Specialty Metals COTS-Exempt Country of Origin United States USMCA Qualifying No Schedule B 392690.9988 ECCN EAR99
$15.00
Flexible Rubber Foam Pipe Insulation Tube Slit, 1/2" Thick Wall, 1-7/8" ID, 6 Feet Long
Flexible Rubber Foam Pipe Insulation Tube Soft and easy to install, this insulation restricts absorption of water, air, and gas. It is often used on cold and hot water lines and refrigeration lines. Seal with contact adhesive (sold separately). To use outdoors, coat in acrylic paint. Slit tubes have an adhesive strip closure. For Use On Pipe Insulation Type Tube Wall Thickness 1/2" ID 1 7/8" OD 2 7/8" For Pipe Size 1 1/2 Length 6 ft. Temperature Range -295° to 180° F Heat Flow Rate 0.25 Btu @ 75° F Density 4.5 lbs./cu. ft. Material Buna-N/PVC Foam Color Black Closure Type Adhesive Strip Flexibility Flexible Cell Type Closed Tube Style Slit Specifications Met ASTM E84 25/50 for Flame and Smoke, ASTM C534 Performance Properties Moisture Resistant R Value 2 Additional Specifications SDS RoHS RoHS 3 (2015/863/EU) Compliant REACH REACH (EC 1907/2006) (06/10/2022, 224 SVHC) Compliant DFARS Specialty Metals COTS-Exempt Country of Origin United States USMCA Qualifying No Schedule B 400911.0000 ECCN EAR99
$42.00
FNPT Cap
BVV™ FNPT Cap Best Value Vacs brand stainless steel parts are made with precision 304 Grade Stainless Steel and are clean and free from burrs or debris. These fittings are NPT threads (National Pipe Taper) and will compress against other Female/Male NPT threads creating a tighter and tighter connection. All NPT threads require thread sealant to create a watertight and gas-tight seal between the threads. We recommend using Yellow Gas PTFE Tape because it is rated for gases and is UL listed and it is NOT recommended to use white PTFE tape because it is not rated for gas service. Female NPT caps are designed for capping off male NPT threaded connections on extraction systems. Specifications Material 304 Stainless Steel Connection Type 1/4"-18 FNPT 3/8"-18 FNPT 1/2"-14 FNPT Sizes Available: 1/4" 3/8" 1/2"
$4.00
Foam Insulation for Hose and Tubing - 6 Feet
Foam Insulation for Hose and Tubing - 6 Feet This foam insulation is good for silicone tubing, stainless steel braided hosing, compression hard line tubing, and more! The inner diameter of the foam can be 3/8", 1/2", or 5/8" and must be selected in the drop down menu. This should correspond with the outer diameter of the hose that you want to insulate. The 3/8" option will slide on your hose or tube while the 1/2" and 5/8" options have a taped seam. All options come in 6' lengths. Sizing Chart: Foam Insulation Size: 3/8" 1/2" 5/8" For Compression Tube Size 3/8" 1/2" - For Stainless Steel Braided Hose Size 3/8" * 1/2" - For Silicone Tube Size 1/4" 3/8" 1/2" Composition Nitrile, PVC Flame/Smoke Rating 25/50 Height 1.375 Insulation Nominal I.D. 3/8" Length 72 R-Value R4.1 Temperature Range -297°F to 220°F (-182.78°C to 104.44°C) Country of Origin USA * The 3/8" foam does not have a seam and cannot be easily slid over stainless steel braided hose with permanent end fixtures.
$17.00
Fully Jacketed Base with 1.5" Tri-Clamp Drain Port
Fully Jacketed Base with 1.5" Tri-Clamp/ Tri-Clover Drain Port This Fully Jacketed Base features a full outer jacket to allow the circulation of heat transfer fluid. The base also has a sanitary Tri-Clamp port welded through the jacket and base for easier drainage of processed material and extract from the stainless steel base. This base is made out of 304 High Polish Stainless steel and has 2 1/2" FNPT Ports on the outer jacket to allow the circulation of fluid to heat or chill the base and also has a 1.5" Tri-Clamp port that allows the drainage of material from inside the base without having to lift it up and tip it over. Specifications Material 304 Stainless Steel Sizes Available: 10" Tri-Clamp X 12" 12" Tri-Clamp x 12" Drain Port Size 1.5" Tri-Clamp Jacket Port Size 1/2" FNPT
$450.00 - $550.00
Fully Jacketed Containers
Fully Jacketed Containers Fully jacketed containers are designed to be used as collection pots or collection traps in an extraction system and they allow the circulation of temperature control fluid through the outer welded jacket that has 1/2" FNPT ports to adapt several types of connections too. These Containers are made out of 304 Stainless steel and have Sanitary welds on them.
$190.00 - $415.00
Fully Jacketed Spools
Fully Jacketed Spools 304 Stainless Steel Fully Jacketed Spools allow the user to circulate water through the base of an extractor or the material column to heat up or chill solvent vapor. Has 1/2" FNPT ports. And attached tri clamp fittings on each end for user convenience. BVV™ Fully Jacketed Spools - Drawings
$140.00 - $690.00
FxFxM Street Tee
BVV™ FxFxM Street Tee BVV™ brand stainless steel parts are made with precision 304 Grade Stainless Steel and are clean and free from burrs or debris. These fittings are NPT threads (National Pipe Taper) and will compress against other Female/Male NPT threads creating a tighter and tighter connection. All NPT threads require thread sealant to create a watertight and gas-tight seal between the threads. We recommend using Yellow Gas PTFE Tape because it is rated for gases and is UL listed and it is NOT recommended to use white PTFE tape because it is not rated for gas service. **NOTE: Pre-Taped option comes from BVV Pre-taped with Yellow UL Listed Gas PTFE Tape on the Male NPT threads ONLY for a +0.50c charge per male npt end. (JIC Threads DO NOT need to be taped.) FxFxM Street Tees have 2 Female NPT ports and 1 Male NPT port and depending on the configuration of the application these street tees may offer fewer connection points or better configurability than MxMxF street tees. BVV™ FxFxM Street Tee - Data Sheet
$20.00 - $40.50
FYRA for End of Primary Drying Detection | Vacuum Drying Monitoring | for Lyophilization| CE, UL, CSA
FYRA for End of Primary Drying Detection. This bundle is set up to allow for vacuum drying applications like freeze-drying and vacuum ovens to help determine the end of drying. Will help you detect when most of the water or residual solvent from a product has been removed or the end of primary drying has been reached in a vacuum drying application. Background on How this FYRA End of Primary Drying package works: When a freeze dryer is equipped with both a thermal and direct measurement, these sensors can be utilized to indicate the end of primary drying (Source). Step One: Clean process documentation | Get a baseline Characterize the convection-enhanced Pirani and the capacitance manometer (in this case the DCP Quantum) against each other in a dry, empty and refrigerated system. The freeze dryer is turned on, as per the manufacturer’s operator manual, with nothing on the shelf. The shelf temperature can be left at room temperature, and if so the cold trap, the condenser, and the vacuum pump should be on and running for a period of time The vacuum oven or freeze dryer is allowed a period of time to become stable in this condition and the Pirani and capacitance manometers are read. The difference in their pressure readings in a dry, empty and refrigerated freeze dryer will be relatively small (mT to 10’s of mT) when the system is working properly. DigiVac will NOT calibrate these two gauges against each other. There may always be slight differences in their readings due to their difference in design. The difference in pressure (ΔP) between these two gauges, when dry, empty, and refrigerated, indicates how close they come together when there is little to no water vapor in the gas mix over the product. Step 2: Drying with Product The intent of primary drying is to maximize the sublimation rate within the product. As such the gases in the chamber have a high water vapor content. The Pirani sensor will read a higher pressure than the capacitance manometer. As freeze drying progresses the amount of ice converting to vapor through the sublimation process will decrease as the product becomes lyophilized from the top through the bottom of the product. Eventually, the Pirani and capacitance manometers will approach the ΔP that was established in a dry, empty and refrigerated system. Approaching this ΔP value indicates that the end of primary drying has occurred. The DigiVac FYRA controller has a rich remote command-line interface which enables the user a high degree of remote control and monitoring from any computer when communicating through the USB port. Calibrated—Every FYRA is calibrated and pretested under actual vacuum against a NIST standard (Need NIST traceable documentation? Add this option to your order) Applications—Ideal for End of Drying Detection, Freeze Drying Primary Drying Monitoring, and Vacuum Oven Drying Monitoring and Detection DCP Quantum DuoSense Measurement Range: .05 mT to 1000 Torr 275 Convection-enhanced Pirani Measurement Range: 0.1mT to 1000 Torr FYRA Bleed Vacuum Controller Components: FYRA controller Convection-enhance Pirani KF25 gauge sensor | Lesker 275, driver card, and Pirani sensor cable Quantum DCP Gauge and driver card | DuoSENS Capacitive Piezo Vacuum Sensor 0.01 to 1000 Torr, Gas Independent 3 Simple Steps for Vacuum Process Set-up with FYRA Vacuum Controller: Plumb the vacuum gauge(s) and valve into your vessel Connect the sensor, power, and I/O cables into FRYA Measure and control vacuum
$3,456.00
Gas PTFE Tape
Gas PTFE Tape Yellow gas line PTFE Tape is used for hydrocarbon extraction systems and mandatory for any system with solvents. The PTFE tape is a thick threaded sealant that can be used on different plastic and metal pipes. This easy to use tape can be used to help prevent cross threading and form a leak proof seal. Suitable for lines carrying water, oil, gas, and propane. Pressure rating 10,000 PSI.
$5.50 - $7.00
Gellan Gum Powder for Mushrooms Mycology
Gellan Gum Powder Low Acyl | 99.5% Purity Gellan Gum is a high- molecular weight polysaccharide gum that is a product of fermentation of carbohydrates by pseudomonas Elodea which is purified, dried and powdered. Gellan gum is ideal for most microbial and plant tissue culture applications. It’s gelling property makes it a viable ingredient of jellies, beverages, dairy products etc.. This superfine gellan gum dissolves quickly and has a high gel strength making it an excellent choice for a variety of applications an petri dishes. STORAGE: Cool dry conditions, sealed original package Mix: 10gram per. 500ml GELLANGUM CONTENT: 99.5% PARTICLE SIZE 60MESH: 99.0% TRANSPARENCY: 86.3% GEL STREGNTH: 980gm/cm^2 pH: 6.5 TURBIDITY: 8.0NTU HEAVY METAL: <20 ppm. TOTAL PLATE COUNT: <1000CFU/gm SALMONELLA: NEGATIVE E.COLI: NEGATIVE YEAST AND MOLDS: <200CFU/gm SHELFLIFE: 4 years CAS#71010-52-1 Directions for Use: Mix 10g of powder per 500ml of distilled water. Boil and stir until powder is fully dissolved. Sterilize the mixture for 45min @15psi 250°F (121°C) in a pressure cooker or autoclave. Allow mixture to cool to approximately 140°F (60°C) *To avoid excessive condensation. Fill dishes with 15ml of mixture, approximately ~30-35 dishes.
$11.90 - $59.50
GL-14 Cap
GL-14 Cap This GL-14 cap is used for sealing off GL-14 connections or venting vacuum in a system without the use of a valve. Gasket not included. (Note: Only 1 cap included. Increase quantity to order more caps.)
$5.00
Glas-Col Mantle and Controller
Glas-Col Mantle and Controller Specifications Material Aluminum Housed Max Temperature C 400 Height (in) 10 Outside Diameter (od)(in) 13.66 Capacity 22L Volts 115 Watts 2 @ 770 Includes: Separable 4-2ft., 2-wire cord and locking connector
$3,253.00
Glas-Col Stirmantle
Glas-Col Stirmantle Glas-Col offers two types of StirMantles: Electromagnetic (50 to 750 rpm) and Motor Driven (100 to 1850 rpm). The maximum rpms available for each type depends on the viscosity of the solution being heated. Electromagnetic StirMantles are typically used with aqueous solutions like water, while the Motor Driven units use a powerful magnet for higher viscous solution like oils. StirMantles withstands 400°C internal operating temperature. EMS series include the heating mantle, speed control and stir-bar. TEM series only includes the heating mantle and allows the customer in select different speed control options or combined speed/temperature packages like the 104A HS112. WARNING: chemical spillage, overheating, overloading, and general misuse will greatly reduce service life! Note: The temperature probe this mantle comes with can only be used with a thermowell. If you are using it with BVV™ glassware you will need to add SKU: TK1/4-12 or TK1/4-18 depending on what mantle size is selected.
$1,000.00 - $1,450.00
Glass Funnel Non-Jointed
Glass Funnel Non-Jointed This glass funnel is perfect for pouring liquids into any type of container and especially for small-mouthed bottles or flasks and comes in various diameters such as 50mm, 75mm, and 120mm. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$2.25 - $4.50
Glass Stirring Rods - 10 Pack
Glass Stirring Rods - 10 Pack These Glass Stirring Rods come in a pack of 10 and are 6mm in diameter and come in various lengths. They are a great way to stir or blend chemicals together without having to worry about contamination or reaction to a metal imparting taste into a product. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$4.00 - $6.00
Glass Stopcock with PTFE Plug
Glass Stopcock with PTFE Plug Glass PTFE Stopcocks allow the user to connect a valve inline to a system and allows the user to connect a flexible rubber hose to the stopcock. There are 2 sizes available with 8mm OD and 2mm bore sizes and 10mm OD and 4mm bore size. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$18.00
Glass Vac 10 Gallon Aluminum Vacuum Chamber
Glass Vac 10 Gallon Aluminum Vacuum & Degassing Chamber (Comes with 2 Year Limited warranty) This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Utility Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. Glass Vac Vacuum Chambers are ideal for wood workers using the wood stabilization process because the glass lid will not deteriorate like acrylic or polycarbonate lids. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: Aluminum Vessel Chemically Inert Glass Lid Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum. Specification Chamber Material 3004 Aluminum Gasket Material Silicone Lid Material Glass Internal Dimensions (ID) 15" Tall x 14" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC HosePlatinum Cured Silicone PadBlack 50 Micro Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings. Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Exludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min. For shipping info including Import/Export details visit our Shipping link at the bottom of the page.
$329.00
Glass Vac 15 Gallon Aluminum Vacuum Chamber
Glass Vac 15 Gallon Aluminum Vacuum Chamber (Comes with 2 Year Limited warranty) This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Utility Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. Glass Vac Vacuum Chambers are ideal for wood workers using the wood stabilization process because the glass lid will not deteriorate like acrylic or polycarbonate lids. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: Aluminum Vessel Chemically Inert Glass Lid Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum. Specification Chamber Material 3004 Aluminum Gasket Material Silicone Lid Material Glass Internal Dimensions (ID) 17.2" Tall x 16-1/8" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC Hose Platinum Cured Silicone Pad Black 50 Micro Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings. Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Exludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min. For shipping info including Import/Export details visit our Shipping link at the bottom of the page.
$418.00
Glass Vac 3 Gallon Aluminum Vacuum Chamber
3 Gallon Vacuum & Degassing Chamber (Comes with 2 Year Limited warranty) This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Utility Patent #14/533,548) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. Glass Vac Vacuum Chambers are ideal for wood workers using the wood stabilization process because the glass lid will not deteriorate like acrylic or polycarbonate lids. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: Aluminum Vessel Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum. Specification Chamber Material 3004 Aluminum Gasket Material Silicone Lid Material Glass Internal Dimensions (ID) 9" Tall x 10" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC Hose Platinum Cured Silicone Pad Black 50 Micro Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings. Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Exludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min. For shipping info including Import/Export details visit our Shipping link at the bottom of the page.
$154.00
Glass Vac 5 Gallon Aluminum Vacuum Chamber
5 Gallon Vacuum Chamber (Comes with 2 year Limited Warranty) This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Utility Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. Glass Vac Vacuum Chambers are ideal for wood workers using the wood stabilization process because the glass lid will not deteriorate like acrylic or polycarbonate lids. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: Aluminum Vessel Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum. Specifications Chamber Material 3004 Aluminum Gasket Material Silicone Lid Material Glass Internal Dimensions (ID) 10" Tall x 12" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC Hose Platinum Cured Silicone Pad Black 50 Micron Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings. Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Exludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min. For shipping info including Import/Export details visit our Shipping link at the bottom of the page.
$233.00
Glass Vac 7 Gallon Aluminum Vacuum Chamber
Glass Vac 7 Gallon Aluminum Vacuum & Degassing Chamber (Comes with 2 Year Limited Warranty) This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Utility Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. Glass Vac Vacuum Chambers are ideal for wood workers using the wood stabilization process because the glass lid will not deteriorate like acrylic or polycarbonate lids. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: Aluminum Vessel Chemically Inert Glass Lid Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum 3003 Grade Aluminum Body, lightweight and durable Precision lip edge at the top for the protection of silicone gasket Specification Chamber Material 3004 Aluminum Gasket Material Silicone Lid Material Glass Internal Dimensions (ID) 8" Tall x 16" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC HosePlatinum Cured Silicone PadBlack 50 Micro Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings.
$318.00
You have seen 768 out of 1155 products