BVV
Chromatography Column Kit
Chromatography Column Kit Chromatography Column Kit This 3”x24” chromatography column features an internal volume of 2.7L. It’s commonly used for removing pesticides, separating components, and cleaning different chemical compounds. Additional consumables or accessories will be needed depending on application. Capacity can be increased with an additional reservoir adapted to the top 45/50 Rodaviss joint. Rodaviss joints are great for disconnecting any stubborn joints. Light grease is still recommended when assembling joints. This kit features: Casted base with 36” rod stand Support ring Chain clamp Needle control valve 3”x24” column with 2.7L capacity 45/50 Rodaviss joint Sintered disk Stop cock For additional information or questions regarding this kit, accessories, and consumables contact our customer support line. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$485.00
Closed Column Conversion Kit
Closed Column Extractor Conversion Kit This conversion kit will allow you to convert a closed column into a Closed-loop Apollo extractor. ***Disclaimer: Photos are of 1LB upgrade kit. 135g is not pictured yet.*** The V1 kit will include the following: Extractor Base Hemispherical Extractor Lid with BVV 316SS Full Bore Valves Polycarbonate Sight Glasses (2x) Tri Clamp Clamps Tri-Clamp Gaskets 1.5" 150 Mesh Gasket Stainless Steel Braided Hoses (2x) LP Storage and Recovery Tank The V2 kit will include the following: Extractor Base Splatter Platter Hemispherical Extractor Lid with BVV 316SS Full Bore Valves Polycarbonate Sight Glasses (2x) 1.5" BVV Ball Valve Tri Clamp Clamps Tri-Clamp Gaskets 1.5" 150 Mesh Gasket Stainless Steel Braided Hoses (2x) LP Storage and Recovery Tank
$560.00 - $1,670.00
Closed Column Extractor Starter Kit
Complete Closed Column Extractor Kit BVV has bundled our recommended vacuum chamber, vacuum pump, and column extraction system to offer customers the most cost-effective solution possible. The Closed Column Extractor Kit is designed to pair well with the other products included in the extraction kit. The items in the kit cover every process from start to finish on your essential oil extraction (excluding butane) and is easy for beginner operators to use. The first step of the oil extraction process is to use the closed column extractor to extract the essential oils from the plant material into a pyrex dish. The user then transfers the oil with residual solvent into the two-gallon vacuum chamber; the digital heating pad is attached to the bottom of the chamber after setting the temperature. The V4D 4CFM 2 Stage vacuum pump exerts a high vacuum to purge and degass residual solvent or gases trapped inside the oil. (Note: This process may take up to 5 days.) Once the purging process is complete, the oil extraction can be used immediately or transformed into a variety of applications. Professional Kit Adds the following: Compound Gauge Sight Glass Shower Head Best Value Vacs 2 Gallon Vacuum Chamber 90 Day Registered Warranty Best Value’s unique, patent-pending gasket design (Utility Patent #14/533,548) and formidable chamber are designed to last 10,000 uses with proper care and maintenance. The gasket is made reversible for easy peel-off and peel-on functionality, effectively doubling the life of our system. The chamber is equipped with user-friendly vacuum connections that fit most vacuum pumps on the market. Every chamber is tested before shipping to lose no more than 2.5Hg/24hrs. Product Features: Aluminum Vessel Highly durable and reversible silicone gasket Glycerin-filled vacuum gauge 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum-rated HVAC hose to pull a vacuum. 9" Digital Heat Pad 90 Day Registered Warranty This 9” reprogrammable Digital Heat Pad comes with full, detailed instructions. Product Features UL Listed Fahrenheit Digital Controller Min Temp: Ambient + 5Max Temp: 160F Voltage: 110VAC Only Power Consumption: 218-watt Digital Control: Increments of 1 Degree Accuracy: +/- 0.2 Degrees Relay Lifespan: Approx. 10 million cycles BVV™ V4D 4CFM Two Stage Vacuum Pump This is the BVV™ V4D 4CFM Two Stage Vacuum Pump used in botanical extraction. Please refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Feature Internal Check Valve Oil Mist Filter Cap Larger Oil Reservoir for longer oil life Lightweight Rubber Feet for noise dampening Reliable, economical, and efficient Models BVV4D BVV7S BVV9D Stage 2 1 2 Ultimate Vacuum (Microns) 15 75 15 Refrigerant Classes A1 Non-Toxic, Non Flammable Dimensions (in) 12.4 x 4.8 x 10.16 12.4 x 4.8 x 10.16 15 x 6.3 x 11.22 Weight (lbs) 19.4 16.5 32 Free Air Displacement 4.3 CFM 6.4 CFM 8.5 CFM Motor Size (HP) RPM 1 HP 3440 RPM Oil Capacity 10oz / 300ml 14.5oz / 410ml 24oz / 680ml Voltage 110V 60 Hz Power Cord Hard Wired 3m / 9.8' Power Cord Power Switch Standard On / Off Operating Temperature Range 32F to 125 F (0C to 52C) Gas Ballast Valve Yes No Yes Intake Fittings Stainless Steel Inlet Fitting with 1/4" SAE & 3/8" JIC Male Ports *Note: Column capacity may vary depending on the density of packed material and packing density. Capacity is calculated using the industry standard of 4.2g/in3. This is the upper limit for column capacity. Low density, uncut, and/or lightly packed material can reduce capacity by 50%. For best results, we recommend to tightly pack coarse ground material.
$695.00 - $955.00
Closed Loop Recovery Kit
Closed Loop Recovery Kit This closed loop upgrade kit provides all of the essential ancillary equipment to upgrade an extraction system but does not include an active recovery pump (sold separately). An actively run closed loop extractor will increase productivity by reducing recovery time and overall run time of the system by forcing vapors through a solvent recovery pump. This Kit Includes the Following BVV™ Large Condensing Coil 1/4" x 24" SS JIC Braided Hose (3) 1/4" x 48" SS JIC Braided Hose 1/4" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV™ 5' HVAC Hose Milwaukee Vacuum Tee Note: This kit DOES NOT include a recovery pump and must be purchased separately.
$400.00 - $665.00
Cold Trap Flare with washer, O-ring and locknut
Cold Trap Flare with washer, O-ring and locknut This is a replacement Cold Trap Flare with stainless steel washer, Buna-N O-ring and nylon locknut. Connection sizes are 1/4" HVAC Flare with 5/16-18 threaded Stem.
$8.00
Cold Trap O-ring for Inner Vessel
Cold Trap O-ring for Inner Vessel This is a replacement O-ring gasket for the inner vessel of the cold trap to create a seal between the lid and dry ice container. Material: Silicone
$20.00
Color Remediation Column CRC
Color Remediation Column For BHO Extraction Color Remediation Columns are secondary columns used as a filtration cartridge for hydrocarbon and ethanol extraction systems. Removing impurities from extracted oils is aided by filter media, packed in the column above a triple filtration stack. The CRC features a bypass path, allowing the operator to skip the column in case of a clog. What simplifies the color remediation process is bundling the cartridge with the filter media. We have paired the unit with suggested media, supplied in the proper ratio, and a standard operating procedure. This makes filtration easy, allowing you to get it right the first time without having to guess. The CRC is a 4" x 12" spool with triple filter plates and rack mounting. Choose 1/4", 3/8" or 1/2" flares. This CRC Kit Includes: Color Remediation Column Rack Mounting Brackets 100 pack of 8 and 20-micron filter papers 1000g of Activated Alumina 1000g of Silica 60 1000g of Pure-Flo® B80 1000g of PurifiDE XG-12 Instruction Manual
$1,365.00 - $1,718.00
Color Remediation Column CRC w/ Bypass
Color Remediation Column w/ Bypass The CRC is a secondary column used as a filtration cartridge for hydrocarbon and ethanol extraction systems. Filter medias are packed in the column above a triple filtration stack, which aids in the removal of impurities from extracted oils. The CRC features a bypass path, allowing the operator to skip the column in case of a clog. The color remediation process is made simple by bundling the cartridge with the needed filter medias. We have paired the unit with suggested media, supplied in the proper ratio, and a standard operating procedure. The included procedure takes all the guesswork out of filtration, delivering the desired results the first try. Our CRC comes available with 1/4",3/8", and 1/2" MJIC connections, your choice of a 3",4", and 6" diameter spool with a 12" height, and rack mounting brackets standard to accommodate systems of any size. This Kit Includes: Color Remediation Column Rack Mounting Brackets 100 pack of 8 and 20-micron filter papers 1000g or 2.5 kg of Activated Alumina 1000g or 2.5 kg of Silica 60A 1000g or 2.5 kg of Pure-Flo® B80 (81, 5000, 6000 or Color Bleach)*Substitutes 1000g of Celite®545 Instruction Manual
$850.00 - $1,350.00
Compact In-line Sight Glass Female NPT Stainless Steel (Flow Sight)
The body of the flow sight is 304 stainless steel. The glass sight has a pressure tight, solid gasket design with Viton seals. The unit tolerates temperatures up to 180° F. The maximum recommended pressure is 125 PSI. BVV™ FNPT Stainless Steel Sight Glass - Data Sheet Specifications 1/4" 3/8" 1/2" 1" Body Material 304 Stainless Steel Gasket Material Viton Length 2-3/16" 2-1/4" 2-1/2" 2-7/8" Width 7/8" 1" 1-1/4" 2" Viewing Port Size 1" 1-1/8" 1-3/16" 1-1/4" PSI Rating 150 150 100 100
$74.00 - $105.00
Compression Ring for Filter Plates
Compression Ring for Filter Plates These compression rings designed to fit in Tri-Clamp/ Tri Clover spools are used in combination with filter plates or inline filter kits by providing compression to the filter media such the pre-cut stainless steel mesh filters or ashless filter media to keep them in place during the extraction process. Sizes Available: 8" Specification Material: 304 Stainless Steel
$15.00
Compression TEE 1/2" Compression x 3/4" Compression x 1/2" FNPT
Compression TEE 1/2" Compression x 3/4" Compression x 1/2" FNPT made out of 304 stainless steel
$40.00
Compressor Head BARE for BVV Recovery Pump/ CMEP Retrofit
This is a replacement compressor head for the BVV2CYL, BVV4CYL, and BVVCMEP-RETRO. It is a full stainless steel head and has all the proper holes drilled to fit on our recovery pumps.
$35.00
Conical Flask
Conical Erlenmeyer Flask Disclaimer: Flasks may not be perfectly flat on the bottom and may have minor surface imperfections. Bring efficiency and convenience to any experiment with the Glass Conical Flask. These conical flasks perform a wide variety of functions and are commonly used in laboratory settings. Conical flasks can capture, store, and measure material when used with a Buchner funnel or glass funnel. But that’s not all. This flask can also mix, boil, and heat chemicals, thanks to its uniform, thick walls, unique design, and stopper for heating. Our conical flasks are flat bottomed and come with ground 24/40 joint, and if used in a vacuum application, requires vacuum grease to help create an airtight vacuum seal during the process. Additionally, the Glass Conical Flasks are thermal shock resistant and chemical resistant. Its tapered sides and narrow neck allows for easy swirling and stirring of an experiment. Key Features: Chemical resistant and thermal shock resistant Reliable, durable wall thickness Cylindrical neck for easy swirling and stirring Reduces evaporation of liquid compared to beakers Tri-clamp fitting ends for convenience Builds process lines without the need for on-site welding fabrication Can be easily moved, dissembled, or resembled Versatile and cost-effective Sizes Available: 250ml - 24/40 Ground Joint 250ml - 24/40 Ground Joint 500ml - 24/40 Ground Joint 1000ml - 24/40 Ground Joint 2000ml - 24/40 Ground Joint 3000ml - 24/40 Ground Joint *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$10.00 - $75.00
Conical Flask Non Jointed
Conical/Erlenmeyer Non-Jointed Flask This Non-Jointed Conical flask is made from thick wall borosilicate glass. It comes in five sizes, including 250ml, 500ml, 1000ml, 2000ml, 3000ml, and 5000ml *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$9.00 - $40.00
Conical Tri-Clamp Reducer
Conical Tri-Clamp/ Tri Clover Reducers Conical Tri-Clamp reducers allow the user to connect differently sized Tri-Clamp parts to each other while adding smoother flow to your extraction system. These reducers are offered in Tri-clamp x Tri-Clamp connections Specifications: Material: 304 Stainless Steel High Polish Interior Standard: 3A Connection Type : Tri-Clamp x Tri-Clamp
$28.00 - $175.00
Cork Stand
Cork Stands Cork stands are used with laboratory glassware to help balance round bottom flasks or prevent damage or support a piece of glassware that is put on it. ***Note: Sizes correlate to round bottom flasks ml sizes. Sizes Available: 250-500ml 500-1000ml 1000-2000ml
$6.00 - $8.00
CPS TRS21 Compressor Head Complete Stainless Rebuild Kit
CPS TRS21 Compressor Head Rebuild Stainless Kit Upgrade the compressor head on the TRS21 to be compatible with CBD oils by replacing all the existing O-ring seals with Viton. Replace all brass fittings with Stainless Steel to by inline with FDA on consumable products. Replace springs and valves. Compressor Head Rebuild Instructions
$99.00
CPS TRS21 Top Dead Center Piston Depth Calibration Plate
CPS TRS21 Top Dead Center Calibration Plate & Bolts Use with the Top Dead Center Clearance (TDCC) instructions Use this plate and a depth gauge to measure the Top Dead Center Clearance of the piston/cylinder/head assembly. Shims that come with the piston cylinders are stacked to create an area of displacement between the top of the cylinder and the compressor head. BVV's Recommended depth is between 0.008" and 0.012" for the CPS TRS21 for optimum performance. Top Dead Center Clearance Instructions *Depth Gauge Not included, its only used for reference in the photo. Any type of simple digital depth gauge will work to check the piston displacement.
$30.00
CPS Vacuum Pump Activated Carbon Exhaust Filter
Carbon Exhaust Filter for CPS Vacuum Pumps Replaces Koby Junior (US Patent# 3169112A) CPS Vacuum Pump Activated Carbon Filter for use with CPS brand vacuum pumps. This filter will adsorb contaminants such as oil aerosols, oil vapors, certain other hydrocarbon vapors, and trace moisture. They also trap all foreign solid particles and bacteria down to 0.5 microns in size. Key Features: Purifies Exhaust Gases from Vacuum Pumps Up to 19 CFM 0.5 Micron Filtration levels. Helps Maintain Safe Working Environment Adsorbs Organic Vapors and Small Particles High-Efficiency Filtration Minimal Pressure Drop Maintenance Free - Completely Disposable Pressure Safe to 90 PSI M26 x 1.0 - Carbon Steel Pump Connection Filter connections 1/4" NPT Pipe Fitting Connections Removes the following contaminants: Oil Mist Oil Aerosols Oil Vapors Hydrocarbon Vapors Moisture Droplets Dust Pipe Scale Rust Fine Particles Odors Organic Aerosols Other Foreign Matter Lifespan:720 hrs. of continuous operation. (Then replacement is recommended) **NOTE PUMP NOT INCLUDED
$115.00
Cryogenic 45L Centrifuge Extractor Kit
Cryogenic 45L Centrifuge Extractor Kit EXPECT 3-WEEK LEADTIME Cryogenic 45L Centrifuge Extractor Kit Overview: The BVV Cryogenic 45L Centrifuge Extractor Kit is a modular closed loop alcohol extraction system with low temperature extraction in mind. It features low temperature rated (-60°C) components including PTFE envelope gaskets, pneumatic diaphragm pumps and cryogenic rated ball valves for longevity. The centrifuge controller and motor are EX rated and come with supporting documents making it easier to get approved for operation. Load centrifuge bags with 8-15lb (10lb avg.) biomass and line them up for an efficient extraction process. This system makes repeatability easier by letting the operator control extraction parameters including soak/agitation time, spin dry time, target alcohol temperature, and different pore material bags and filtration socks in our Pressure Filtration System (PFS). The system also allows operators to re-direct the first wash back to the holding vessel to re-chill if needed and go for a second extraction. This allows full use of alcohol’s extraction ability and minimize time spent recovering solvent in a rotary evaporator or falling film. Users will have to dial in their parameters and washes based on biomass potency. Low temperature extraction leads to less refinement after the extraction process. Inline PFS allows for fine particulate refinement down to 1µm. Higher potency will require further post processing for the removal of unwanted compounds. NOTE: CHILLER AND AIR COMPRESSOR NOT INCLUDED IN THE KIT. CALL IN FOR RECOMMENDED CHILLER AND AIR COMPRESSOR. Insulation: Insulation package is included with the order but does not come installed upon arrival. Insulation included are straight tubing, tees, and elbows. BVV can install insulation as an add on prior to shipping the system out. This will also include color coordinated zip ties that help assembly process. Assembly diagrams will also be included with the system. Installation requires taping seams cutting tubing to length, and zip tying tees and elbows. Holding vessel and centrifuge are vacuum insulated via the jacket. Supporting documents included: Standard Operating Procedure for CF45L-CRYO-01 Centrifuge Wiring Instructions CF45L-CRYO-01 Manual CF45L-CRYO-01 Assembly Diagram Centrifuge Controller EX Certificate Centrifuge Motor EX Certificate Pneumatic Pump specification sheet with operating pressure/flow chart CALL IN TO SCHEDULE A FULL PRESENTATION WITH ONE OF THE CRYOGENIC 45L CENTRIFUGE EXTRACT KIT. QUESTIONS CAN BE ANSWERED BY OUR ENGINEERING TEAM. Specifications Centrifuge Controller Power Requirements 220v 1PH 60Hz, 20A Circuit Liquid Transfer Pumps Pneumatic (Compressor Required) Drum Volume 45L Drum Dimensions 17.7" (450mm) Diameter x 11-7/8" (300mm) Deep Centrifuge Bags Included 1 of Ea: 1, 10, 50, 100, 200 Micron Max Biomass Capacity 15lbs (6.8Kg), Recommended 10lbs Solvent Capacity per Run 17 Gallons Centrifuge Speed 1500 RPM Centrifuge Weight 794lbs (360Kg) Overall System Dimensions 12'6" x 13'8" x 71" (3810mm x 4166mm x 1804mm) **with chiller next to system System Temperature Rating -60C (-76F) Material in Contact with Solvent and Extract PTFE envelope, Silicone, 304SS, BIIR(butyl) *FDA & USDA compliant Footprint: NOTE: CHILLER INCLUDED IN EXTRACTION SPACE WILL NEED TO BE APPROVED FOR USE IN C1D2 SPACE. AIR COMPRESSOR FOR PNEUMATIC PUMPS NOT INCLUDED IN DIAGRAM.
$51,000.00
Crystallizing Dish
Crystallizing Dish Crystallization dishes work great for small batch mixing using heating & stirring plates, evaporation of any solvents in small amounts, and crystallization. This crystallization dish is made out borosilicate glass and features a pouring spout making it easy to transfer any liquid substance. Specifications Material Borosilicate External Diameter 98mm (+/- 1mm) Overall Height 49mm (+/- 1mm) Internal Diameter 94mm (+/- 1mm) Internal Depth 47mm (+/- 1mm) Features Pouring Spout
$5.00
Dark City Molds Coin Gummy Molds
Coin Gummy Molds Sizes Available: 2.15mL 2.17mL 2.5mL (20 Minimum to Order!) 3.26mL (Triangle State Design) 7.1mL 7.1mL (Bitcoin Design) 34.3mL 45.2mL MOLD PROPERTIES 100% FDA Approved Food-Contact Safe Platinum Silicone Temperature Resistant - Freezer, Dishwasher & Oven Safe Half Sheet Molds Are Optimized to Fit 2 Molds Per 18” x 26” Full Size Baking Sheet Strategically Designed Geometry Optimized For Rapid Extraction Proprietary Natural Slip Finish For Oil Free Workflow Precision Diamond Tooled Masters For Superior Detail & Finish Guaranteed Highest Resolution Designs On The Market Rapid Demolding Rates - Extract up to 1000+ Gummies Per Minute Perfect for Gummies, Hard Candies, Caramels, Chews, Chocolates, and More 6-10 Year Expected Lifetime with Proper Care & Use OUR PROMISE Every mold that leaves our facility is covered by DCM’s 18 Month Gold Standard Warranty. If you experience any issues within that period, we'll immediately exchange the mold in question. No hassle. No fuss. Committed to creating the highest quality platinum silicone molds in the world. Whether you’re manufacturing gummies, hard candies, caramels, chews, or other confections, our diamond tooled molds will provide superior finish and detail to ensure maximal aesthetic clarity and operational efficiency for your manufacturing workflow. We’re proud to offer best-in-industry performance with our Rose Pro Series™ silicones as well as the most competitive price points on translucent platinum molds currently available. *Assumes a 1ml : 1.4g recipe ratio. Since weight is a metric of a recipe's specific density, we cannot exactly determine the weight of your specific recipe. Please consult the designated volume (ml) specification above to calculate a more exact weight (g) reading. All Dark City Gold Standard SOPs yield a 1ml : 1.4g ratio.
$150.00 - $250.00
Dark City Molds Cube Gummy Mold
Cube Gummy Mold Available Sizes: 1mL 1.6mL 2.2mL 3.4mL MOLD PROPERTIES 100% FDA Approved Food-Contact Safe Platinum Silicone Temperature Resistant - Freezer, Dishwasher & Oven Safe Half Sheet Molds Are Optimized to Fit 2 Molds Per 18” x 26” Full Size Baking Sheet Strategically Designed Geometry Optimized For Rapid Extraction Proprietary Natural Slip Finish For Oil Free Workflow Precision Diamond Tooled Masters For Superior Detail & Finish Guaranteed Highest Resolution Designs On The Market Rapid Demolding Rates - Extract up to 1000+ Gummies Per Minute Perfect for Gummies, Hard Candies, Caramels, Chews, Chocolates, and More 6-10 Year Expected Lifetime with Proper Care & Use OUR PROMISE Every mold that leaves our facility is covered by DCM’s 18 Month Gold Standard Warranty. If you experience any issues within that period, we'll immediately exchange the mold in question. No hassle. No fuss. Creating the highest quality platinum silicone molds in the world. Whether you’re manufacturing gummies, hard candies, caramels, chews, or other confections, our diamond tooled molds will provide superior finish and detail to ensure maximal aesthetic clarity and operational efficiency for your manufacturing workflow. We’re proud to offer best-in-industry performance with our Rose Pro Series™ silicones as well as the most competitive price points on translucent platinum molds currently available. *Assumes a 1ml : 1.4g recipe ratio. Since weight is a metric of a recipe's specific density, we cannot exactly determine the weight of your specific recipe. Please consult the designated volume (ml) specification above to calculate a more exact weight (g) reading. All Dark City Gold Standard SOPs yield a 1ml : 1.4g ratio. Mold Specifications Sizes Avaliable (Volume) Shape Pieces Per Mold Weight Material Options Mold Dimensions Compatibility Square Molds 2.5mL Square 134 3.5g Rose Pro Series, Translucent 280mm x 392mm Hand Fill, Flood & Scrape, Universal Depositor 2.85mL Square 234 3.5g Rose Pro Series, Translucent 290mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 3.57mL Square 120 5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 4mL Square 192 5.6g Rose Pro Series, Translucent 290mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 6mL Square 165 8.4g Rose Pro Series, Translucent 391.6mm x 286.5mm Hand Fill, Flood & Scrape, Universal Depositor Cube Molds 1mL Cube 609 1.5g Rose Pro Series, Translucent 286mm x 398mm Hand Fill, Flood & Scrape, Universal Depositor 1.6mL Cube 275 2.2g Rose Pro Series, Translucent 289mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor 2.2mL Cube 209 3g Rose Pro Series, Translucent 289mm x 365mm Hand Fill, Flood & Scrape, Universal Depositor, Baker Perkins ServoForm Mini 3.4mL Cube 280 4.8g Rose Pro Series, Translucent 275.9mm x 394.7mm Hand Fill, Flood & Scrape, Universal Depositor Triangle Molds 2.66mL Triangle 210 3.7g Rose Pro Series, Translucent 280mm x 379.7mm Hand Fill, Flood & Scrape, Universal Depositor 2.8mL Tetrahedron 95 3.9g Rose Pro Series, Translucent 135mm x 374mm Hand Fill, Flood & Scrape, Universal Depositor 4.1mL Triangle 160 5.7g Rose Pro Series, Translucent 285mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor Mutidose Molds 2.25mL Cube 144 3.2g Rose Pro Series, Translucent 254mm x 355mm Hand Fill, Flood & Scrape, Universal Depositor 3.3mL Rhombus 209 4.6g(each segment: 2.3g*) Rose Pro Series, Translucent 284mm x 375.4mm Hand Fill, Flood & Scrape, Universal Depositor 4mL Square 165 5.5g Rose Pro Series, Translucent 289mm x 380mm Hand Fill, Flood & Scrape, Universal Depositor 12.5mL Rectangle 60 17.5g Rose Pro Series, Translucent 279.3mm x 385.2mm Hand Fill, Flood & Scrape, Universal Depositor 23.5mL Square Rope 20 32g (each segment: 3.2g*) Rose Pro Series, Translucent 258mm x 385mm Hand Fill, Flood & Scrape, Universal Depositor 42.4mL Rectangle 18 59.4g Rose Pro Series, Translucent 240.9mm x 381.3mm Hand Fill, Flood & Scrape, Universal Depositor Cube Molds 1mL Cube 609 15.g Rose Pro Series, Translucent 286mm x 398mm Hand Fill, Flood & Scrape, Universal Depositor 1.6mL Cube 275 2.2g Rose Pro Series, Translucent 289mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor 2.2mL Cube 209 3g Rose Pro Series, Translucent 289mm x 365mm Hand Fill, Flood & Scrape, Universal Depositor 3.4mL Cube 280 4.8g Rose Pro Series, Translucent 275.9mm x 394.7mm Hand Fill, Flood & Scrape, Universal Depositor Coin Mold 2.5mL Coin 120 3.5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 2.17mL Coin 176 3g Rose Pro Series, Translucent 289mm x 374mm Hand Fill, Flood & Scrape, Universal Depositor 2.5mL Coin 120 3.5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 3.26mL Coin 165 4.6g Rose Pro Series, Translucent 289mm x 385mm Hand Fill, Flood & Scrape, Universal Depositor 7.1mL Puck 88 9.9g Rose Pro Series, Translucent 283.2mm x 390.2mm Hand Fill, Flood & Scrape, Universal Depositor 7.1mL (Bit) Coin 88 9.9g Rose Pro Series, Translucent 280.2mm x 386.1mm Hand Fill, Flood & Scrape, Universal Depositor 34.3mL Coin 35 48g Rose Pro Series, Translucent 268.1mm x 371.7mm Hand Fill, Flood & Scrape, Universal Depositor 45.2mL Coin 20 63.3g Rose Pro Series, Translucent 293.0mm x 365.3mm Hand Fill, Flood & Scrape, Universal Depositor Gum Drop 1.3mL Gum Drop 388 1.82g Rose Pro Series, Translucent 286mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 2.15mL Gum Drop 176 3g Rose Pro Series, Translucent 289mm x 392mm Hand Fill, Flood & Scrape, Universal Depositor 3.6mL Gum Drop 140 5g Rose Pro Series, Translucent 259mm x 363.6mm Hand Fill, Flood & Scrape, Universal Depositor
$150.00 - $250.00
Dark City Molds Gem Gummy Mold
Dark City Molds Gem Gummy Mold Available Sizes: 2.85mL- Square Gem 2.85mL- Jewel Gem 4.3mL- Rectangle Gem MOLD PROPERTIES 100% FDA Approved Food-Contact Safe Platinum Silicone Temperature Resistant - Freezer, Dishwasher & Oven Safe Half Sheet Molds Are Optimized to Fit 2 Molds Per 18” x 26” Full Size Baking Sheet Strategically Designed Geometry Optimized For Rapid Extraction Proprietary Natural Slip Finish For Oil Free Workflow Precision Diamond Tooled Masters For Superior Detail & Finish Guaranteed Highest Resolution Designs On The Market Rapid Demolding Rates - Extract up to 1000+ Gummies Per Minute Perfect for Gummies, Hard Candies, Caramels, Chews, Chocolates, and More 6-10 Year Expected Lifetime with Proper Care & Use OUR PROMISE Every mold that leaves our facility is covered by DCM’s 18 Month Gold Standard Warranty. If you experience any issues within that period, we'll immediately exchange the mold in question. No hassle. No fuss. Committed to creating the highest quality platinum silicone molds in the world. Whether you’re manufacturing gummies, hard candies, caramels, chews, or other confections, our diamond tooled molds will provide superior finish and detail to ensure maximal aesthetic clarity and operational efficiency for your manufacturing workflow. We’re proud to offer best-in-industry performance with our Rose Pro Series™ silicones as well as the most competitive price points on translucent platinum molds currently available. *Assumes a 1ml : 1.4g recipe ratio. Since weight is a metric of a recipe's specific density, we cannot exactly determine the weight of your specific recipe. Please consult the designated volume (ml) specification above to calculate a more exact weight (g) reading. All Dark City Gold Standard SOPs yield a 1ml : 1.4g ratio.
$150.00 - $250.00
Dark City Molds Gumdrop Gummy Molds
Dark City Molds Gumdrop Gummy Molds Available Sizes: 1.3mL 2.15mL 3.6mL MOLD PROPERTIES 100% FDA Approved Food-Contact Safe Platinum Silicone Temperature Resistant - Freezer, Dishwasher & Oven Safe Half Sheet Molds Are Optimized to Fit 2 Molds Per 18” x 26” Full Size Baking Sheet Strategically Designed Geometry Optimized For Rapid Extraction Proprietary Natural Slip Finish For Oil Free Workflow Precision Diamond Tooled Masters For Superior Detail & Finish Guaranteed Highest Resolution Designs On The Market Rapid Demolding Rates - Extract up to 1000+ Gummies Per Minute Perfect for Gummies, Hard Candies, Caramels, Chews, Chocolates, and More 6-10 Year Expected Lifetime with Proper Care & Use OUR PROMISE Every mold that leaves our facility is covered by DCM’s 18 Month Gold Standard Warranty. If you experience any issues within that period, we'll immediately exchange the mold in question. No hassle. No fuss. Committed to creating the highest quality platinum silicone molds in the world. Whether you’re manufacturing gummies, hard candies, caramels, chews, or other confections, our diamond tooled molds will provide superior finish and detail to ensure maximal aesthetic clarity and operational efficiency for your manufacturing workflow. We’re proud to offer best-in-industry performance with our Rose Pro Series™ silicones as well as the most competitive price points on translucent platinum molds currently available. *Assumes a 1ml : 1.4g recipe ratio. Since weight is a metric of a recipe's specific density, we cannot exactly determine the weight of your specific recipe. Please consult the designated volume (ml) specification above to calculate a more exact weight (g) reading. All Dark City Gold Standard SOPs yield a 1ml : 1.4g ratio. Mold Specifications Sizes Avaliable (Volume) Shape Pieces Per Mold Weight Material Options Mold Dimensions Compatibility Square Molds 2.5mL Square 134 3.5g Rose Pro Series, Translucent 280mm x 392mm Hand Fill, Flood & Scrape, Universal Depositor 2.85mL Square 234 3.5g Rose Pro Series, Translucent 290mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 3.57mL Square 120 5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 4mL Square 192 5.6g Rose Pro Series, Translucent 290mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 6mL Square 165 8.4g Rose Pro Series, Translucent 391.6mm x 286.5mm Hand Fill, Flood & Scrape, Universal Depositor Cube Molds 1mL Cube 609 1.5g Rose Pro Series, Translucent 286mm x 398mm Hand Fill, Flood & Scrape, Universal Depositor 1.6mL Cube 275 2.2g Rose Pro Series, Translucent 289mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor 2.2mL Cube 209 3g Rose Pro Series, Translucent 289mm x 365mm Hand Fill, Flood & Scrape, Universal Depositor, Baker Perkins ServoForm Mini 3.4mL Cube 280 4.8g Rose Pro Series, Translucent 275.9mm x 394.7mm Hand Fill, Flood & Scrape, Universal Depositor Triangle Molds 2.66mL Triangle 210 3.7g Rose Pro Series, Translucent 280mm x 379.7mm Hand Fill, Flood & Scrape, Universal Depositor 2.8mL Tetrahedron 95 3.9g Rose Pro Series, Translucent 135mm x 374mm Hand Fill, Flood & Scrape, Universal Depositor 4.1mL Triangle 160 5.7g Rose Pro Series, Translucent 285mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor Mutidose Molds 2.25mL Cube 144 3.2g Rose Pro Series, Translucent 254mm x 355mm Hand Fill, Flood & Scrape, Universal Depositor 3.3mL Rhombus 209 4.6g(each segment: 2.3g*) Rose Pro Series, Translucent 284mm x 375.4mm Hand Fill, Flood & Scrape, Universal Depositor 4mL Square 165 5.5g Rose Pro Series, Translucent 289mm x 380mm Hand Fill, Flood & Scrape, Universal Depositor 12.5mL Rectangle 60 17.5g Rose Pro Series, Translucent 279.3mm x 385.2mm Hand Fill, Flood & Scrape, Universal Depositor 23.5mL Square Rope 20 32g (each segment: 3.2g*) Rose Pro Series, Translucent 258mm x 385mm Hand Fill, Flood & Scrape, Universal Depositor 42.4mL Rectangle 18 59.4g Rose Pro Series, Translucent 240.9mm x 381.3mm Hand Fill, Flood & Scrape, Universal Depositor Cube Molds 1mL Cube 609 15.g Rose Pro Series, Translucent 286mm x 398mm Hand Fill, Flood & Scrape, Universal Depositor 1.6mL Cube 275 2.2g Rose Pro Series, Translucent 289mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor 2.2mL Cube 209 3g Rose Pro Series, Translucent 289mm x 365mm Hand Fill, Flood & Scrape, Universal Depositor 3.4mL Cube 280 4.8g Rose Pro Series, Translucent 275.9mm x 394.7mm Hand Fill, Flood & Scrape, Universal Depositor Coin Mold 2.5mL Coin 120 3.5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 2.17mL Coin 176 3g Rose Pro Series, Translucent 289mm x 374mm Hand Fill, Flood & Scrape, Universal Depositor 2.5mL Coin 120 3.5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 3.26mL Coin 165 4.6g Rose Pro Series, Translucent 289mm x 385mm Hand Fill, Flood & Scrape, Universal Depositor 7.1mL Puck 88 9.9g Rose Pro Series, Translucent 283.2mm x 390.2mm Hand Fill, Flood & Scrape, Universal Depositor 7.1mL (Bit) Coin 88 9.9g Rose Pro Series, Translucent 280.2mm x 386.1mm Hand Fill, Flood & Scrape, Universal Depositor 34.3mL Coin 35 48g Rose Pro Series, Translucent 268.1mm x 371.7mm Hand Fill, Flood & Scrape, Universal Depositor 45.2mL Coin 20 63.3g Rose Pro Series, Translucent 293.0mm x 365.3mm Hand Fill, Flood & Scrape, Universal Depositor Gum Drop 1.3mL Gum Drop 388 1.82g Rose Pro Series, Translucent 286mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 2.15mL Gum Drop 176 3g Rose Pro Series, Translucent 289mm x 392mm Hand Fill, Flood & Scrape, Universal Depositor 3.6mL Gum Drop 140 5g Rose Pro Series, Translucent 259mm x 363.6mm Hand Fill, Flood & Scrape, Universal Depositor
$150.00 - $250.00
Dark City Molds Multidose Gummy Molds
Dark City Molds Multidose Gummy Molds Available Sizes: 2.25mL - Cube 3.3mL- Rectangle 4mL - Square 12.5mL - Rectangle 23.25mL - Square Rope 42.4mL - Rectangle Rope MOLD PROPERTIES 100% FDA Approved Food-Contact Safe Platinum Silicone Temperature Resistant - Freezer, Dishwasher & Oven Safe Half Sheet Molds Are Optimized to Fit 2 Molds Per 18” x 26” Full Size Baking Sheet Strategically Designed Geometry Optimized For Rapid Extraction Proprietary Natural Slip Finish For Oil Free Workflow Precision Diamond Tooled Masters For Superior Detail & Finish Guaranteed Highest Resolution Designs On The Market Rapid Demolding Rates - Extract up to 1000+ Gummies Per Minute Perfect for Gummies, Hard Candies, Caramels, Chews, Chocolates, and More 6-10 Year Expected Lifetime with Proper Care & Use OUR PROMISE Every mold that leaves our facility is covered by DCM’s 18 Month Gold Standard Warranty. If you experience any issues within that period, we'll immediately exchange the mold in question. No hassle. No fuss. Committed to creating the highest quality platinum silicone molds in the world. Whether you’re manufacturing gummies, hard candies, caramels, chews, or other confections, our diamond tooled molds will provide superior finish and detail to ensure maximal aesthetic clarity and operational efficiency for your manufacturing workflow. We’re proud to offer best-in-industry performance with our Rose Pro Series™ silicones as well as the most competitive price points on translucent platinum molds currently available. *Assumes a 1ml : 1.4g recipe ratio. Since weight is a metric of a recipe's specific density, we cannot exactly determine the weight of your specific recipe. Please consult the designated volume (ml) specification above to calculate a more exact weight (g) reading. All Dark City Gold Standard SOPs yield a 1ml : 1.4g ratio Mold Specifications Sizes Avaliable (Volume) Shape Pieces Per Mold Weight Material Options Mold Dimensions Compatibility Square Molds 2.5mL Square 134 3.5g Rose Pro Series, Translucent 280mm x 392mm Hand Fill, Flood & Scrape, Universal Depositor 2.85mL Square 234 3.5g Rose Pro Series, Translucent 290mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 3.57mL Square 120 5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 4mL Square 192 5.6g Rose Pro Series, Translucent 290mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 6mL Square 165 8.4g Rose Pro Series, Translucent 391.6mm x 286.5mm Hand Fill, Flood & Scrape, Universal Depositor Cube Molds 1mL Cube 609 1.5g Rose Pro Series, Translucent 286mm x 398mm Hand Fill, Flood & Scrape, Universal Depositor 1.6mL Cube 275 2.2g Rose Pro Series, Translucent 289mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor 2.2mL Cube 209 3g Rose Pro Series, Translucent 289mm x 365mm Hand Fill, Flood & Scrape, Universal Depositor, Baker Perkins ServoForm Mini 3.4mL Cube 280 4.8g Rose Pro Series, Translucent 275.9mm x 394.7mm Hand Fill, Flood & Scrape, Universal Depositor Triangle Molds 2.66mL Triangle 210 3.7g Rose Pro Series, Translucent 280mm x 379.7mm Hand Fill, Flood & Scrape, Universal Depositor 2.8mL Tetrahedron 95 3.9g Rose Pro Series, Translucent 135mm x 374mm Hand Fill, Flood & Scrape, Universal Depositor 4.1mL Triangle 160 5.7g Rose Pro Series, Translucent 285mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor Mutidose Molds 2.25mL Cube 144 3.2g Rose Pro Series, Translucent 254mm x 355mm Hand Fill, Flood & Scrape, Universal Depositor 3.3mL Rhombus 209 4.6g(each segment: 2.3g*) Rose Pro Series, Translucent 284mm x 375.4mm Hand Fill, Flood & Scrape, Universal Depositor 4mL Square 165 5.5g Rose Pro Series, Translucent 289mm x 380mm Hand Fill, Flood & Scrape, Universal Depositor 12.5mL Rectangle 60 17.5g Rose Pro Series, Translucent 279.3mm x 385.2mm Hand Fill, Flood & Scrape, Universal Depositor 23.5mL Square Rope 20 32g (each segment: 3.2g*) Rose Pro Series, Translucent 258mm x 385mm Hand Fill, Flood & Scrape, Universal Depositor 42.4mL Rectangle 18 59.4g Rose Pro Series, Translucent 240.9mm x 381.3mm Hand Fill, Flood & Scrape, Universal Depositor Cube Molds 1mL Cube 609 15.g Rose Pro Series, Translucent 286mm x 398mm Hand Fill, Flood & Scrape, Universal Depositor 1.6mL Cube 275 2.2g Rose Pro Series, Translucent 289mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor 2.2mL Cube 209 3g Rose Pro Series, Translucent 289mm x 365mm Hand Fill, Flood & Scrape, Universal Depositor 3.4mL Cube 280 4.8g Rose Pro Series, Translucent 275.9mm x 394.7mm Hand Fill, Flood & Scrape, Universal Depositor Coin Mold 2.5mL Coin 120 3.5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 2.17mL Coin 176 3g Rose Pro Series, Translucent 289mm x 374mm Hand Fill, Flood & Scrape, Universal Depositor 2.5mL Coin 120 3.5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 3.26mL Coin 165 4.6g Rose Pro Series, Translucent 289mm x 385mm Hand Fill, Flood & Scrape, Universal Depositor 7.1mL Puck 88 9.9g Rose Pro Series, Translucent 283.2mm x 390.2mm Hand Fill, Flood & Scrape, Universal Depositor 7.1mL (Bit) Coin 88 9.9g Rose Pro Series, Translucent 280.2mm x 386.1mm Hand Fill, Flood & Scrape, Universal Depositor 34.3mL Coin 35 48g Rose Pro Series, Translucent 268.1mm x 371.7mm Hand Fill, Flood & Scrape, Universal Depositor 45.2mL Coin 20 63.3g Rose Pro Series, Translucent 293.0mm x 365.3mm Hand Fill, Flood & Scrape, Universal Depositor Gum Drop 1.3mL Gum Drop 388 1.82g Rose Pro Series, Translucent 286mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 2.15mL Gum Drop 176 3g Rose Pro Series, Translucent 289mm x 392mm Hand Fill, Flood & Scrape, Universal Depositor 3.6mL Gum Drop 140 5g Rose Pro Series, Translucent 259mm x 363.6mm Hand Fill, Flood & Scrape, Universal Depositor
$150.00 - $250.00
Dark City Molds Square Gummy Molds
Square Gummy Mold Available Sizes: 2.5mL 2.85mL 3.5mL 4mL 6mL MOLD SPECIFICATIONS Shape: Square Volume: 6ml Estimated weight: 8.4g* Cavity dimensions: 22.2mm x 22.2mm x 12.7mm Mold dimensions: 391.6mm x 286.5mm Pieces per mold: 165 Compatibility: Hand Fill, Flood & Scrape, Universal Depositor Material options: Rose Pro, Platinum Pro MOLD PROPERTIES 100% FDA Approved Food-Contact Safe Platinum Silicone Temperature Resistant - Freezer, Dishwasher & Oven Safe Half Sheet Molds Are Optimized to Fit 2 Molds Per 18” x 26” Full Size Baking Sheet Strategically Designed Geometry Optimized For Rapid Extraction Proprietary Natural Slip Finish For Oil Free Workflow Precision Diamond Tooled Masters For Superior Detail & Finish Guaranteed Highest Resolution Designs On The Market Rapid Demolding Rates - Extract up to 1000+ Gummies Per Minute Perfect for Gummies, Hard Candies, Caramels, Chews, Chocolates, and More 6-10 Year Expected Lifetime with Proper Care & Use OUR PROMISE Every mold that leaves our facility is covered by DCM’s 18 Month Gold Standard Warranty. If you experience any issues within that period, we'll immediately exchange the mold in question. No hassle. No fuss. Committed to creating the highest quality platinum silicone molds in the world. Whether you’re manufacturing gummies, hard candies, caramels, chews, or other confections, our diamond tooled molds will provide superior finish and detail to ensure maximal aesthetic clarity and operational efficiency for your manufacturing workflow. We’re proud to offer best-in-industry performance with our Rose Pro Series™ silicones as well as the most competitive price points on translucent platinum molds currently available. *Assumes a 1ml : 1.4g recipe ratio. Since weight is a metric of a recipe's specific density, we cannot exactly determine the weight of your specific recipe. Please consult the designated volume (ml) specification above to calculate a more exact weight (g) reading. All Dark City Gold Standard SOPs yield a 1ml : 1.4g ratio. Mold Specifications Sizes Avaliable (Volume) Shape Pieces Per Mold Weight Material Options Mold Dimensions Compatibility Square Molds 2.5mL Square 134 3.5g Rose Pro Series, Translucent 280mm x 392mm Hand Fill, Flood & Scrape, Universal Depositor 2.85mL Square 234 3.5g Rose Pro Series, Translucent 290mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 3.57mL Square 120 5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 4mL Square 192 5.6g Rose Pro Series, Translucent 290mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 6mL Square 165 8.4g Rose Pro Series, Translucent 391.6mm x 286.5mm Hand Fill, Flood & Scrape, Universal Depositor Cube Molds 1mL Cube 609 1.5g Rose Pro Series, Translucent 286mm x 398mm Hand Fill, Flood & Scrape, Universal Depositor 1.6mL Cube 275 2.2g Rose Pro Series, Translucent 289mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor 2.2mL Cube 209 3g Rose Pro Series, Translucent 289mm x 365mm Hand Fill, Flood & Scrape, Universal Depositor, Baker Perkins ServoForm Mini 3.4mL Cube 280 4.8g Rose Pro Series, Translucent 275.9mm x 394.7mm Hand Fill, Flood & Scrape, Universal Depositor Triangle Molds 2.66mL Triangle 210 3.7g Rose Pro Series, Translucent 280mm x 379.7mm Hand Fill, Flood & Scrape, Universal Depositor 2.8mL Tetrahedron 95 3.9g Rose Pro Series, Translucent 135mm x 374mm Hand Fill, Flood & Scrape, Universal Depositor 4.1mL Triangle 160 5.7g Rose Pro Series, Translucent 285mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor Mutidose Molds 2.25mL Cube 144 3.2g Rose Pro Series, Translucent 254mm x 355mm Hand Fill, Flood & Scrape, Universal Depositor 3.3mL Rhombus 209 4.6g(each segment: 2.3g*) Rose Pro Series, Translucent 284mm x 375.4mm Hand Fill, Flood & Scrape, Universal Depositor 4mL Square 165 5.5g Rose Pro Series, Translucent 289mm x 380mm Hand Fill, Flood & Scrape, Universal Depositor 12.5mL Rectangle 60 17.5g Rose Pro Series, Translucent 279.3mm x 385.2mm Hand Fill, Flood & Scrape, Universal Depositor 23.5mL Square Rope 20 32g (each segment: 3.2g*) Rose Pro Series, Translucent 258mm x 385mm Hand Fill, Flood & Scrape, Universal Depositor 42.4mL Rectangle 18 59.4g Rose Pro Series, Translucent 240.9mm x 381.3mm Hand Fill, Flood & Scrape, Universal Depositor Cube Molds 1mL Cube 609 15.g Rose Pro Series, Translucent 286mm x 398mm Hand Fill, Flood & Scrape, Universal Depositor 1.6mL Cube 275 2.2g Rose Pro Series, Translucent 289mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor 2.2mL Cube 209 3g Rose Pro Series, Translucent 289mm x 365mm Hand Fill, Flood & Scrape, Universal Depositor 3.4mL Cube 280 4.8g Rose Pro Series, Translucent 275.9mm x 394.7mm Hand Fill, Flood & Scrape, Universal Depositor Coin Mold 2.5mL Coin 120 3.5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 2.17mL Coin 176 3g Rose Pro Series, Translucent 289mm x 374mm Hand Fill, Flood & Scrape, Universal Depositor 2.5mL Coin 120 3.5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 3.26mL Coin 165 4.6g Rose Pro Series, Translucent 289mm x 385mm Hand Fill, Flood & Scrape, Universal Depositor 7.1mL Puck 88 9.9g Rose Pro Series, Translucent 283.2mm x 390.2mm Hand Fill, Flood & Scrape, Universal Depositor 7.1mL (Bit) Coin 88 9.9g Rose Pro Series, Translucent 280.2mm x 386.1mm Hand Fill, Flood & Scrape, Universal Depositor 34.3mL Coin 35 48g Rose Pro Series, Translucent 268.1mm x 371.7mm Hand Fill, Flood & Scrape, Universal Depositor 45.2mL Coin 20 63.3g Rose Pro Series, Translucent 293.0mm x 365.3mm Hand Fill, Flood & Scrape, Universal Depositor Gum Drop 1.3mL Gum Drop 388 1.82g Rose Pro Series, Translucent 286mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 2.15mL Gum Drop 176 3g Rose Pro Series, Translucent 289mm x 392mm Hand Fill, Flood & Scrape, Universal Depositor 3.6mL Gum Drop 140 5g Rose Pro Series, Translucent 259mm x 363.6mm Hand Fill, Flood & Scrape, Universal Depositor
$150.00 - $250.00
Dark City Molds Triangle Gummy Molds
Dark City Molds Triangle Gummy Molds Sizes Available 2.66mL Triangle 2.8mL Tetrahedron 4.1mL 8 Triangle Mold Properties 100% FDA Approved Food-Contact Safe Platinum Silicone Temperature Resistant - Freezer, Dishwasher & Oven Safe Half Sheet Molds Are Optimized to Fit 2 Molds Per 18” x 26” Full Size Baking Sheet Strategically Designed Geometry Optimized For Rapid Extraction Proprietary Natural Slip Finish For Oil Free Workflow Precision Diamond Tooled Masters For Superior Detail & Finish Guaranteed Highest Resolution Designs On The Market Rapid Demolding Rates - Extract up to 1000+ Gummies Per Minute Perfect for Gummies, Hard Candies, Caramels, Chews, Chocolates, and More 6-10 Year Expected Lifetime with Proper Care & Use OUR PROMISE Every mold that leaves our facility is covered by DCM’s 18 Month Gold Standard Warranty. If you experience any issues within that period, we'll immediately exchange the mold in question. No hassle. No fuss. Highest quality platinum silicone molds in the world. Whether you’re manufacturing gummies, hard candies, caramels, chews, or other confections, our diamond tooled molds will provide superior finish and detail to ensure maximal aesthetic clarity and operational efficiency for your manufacturing workflow. We’re proud to offer best-in-industry performance with our Rose Pro Series™ silicones as well as the most competitive price points on translucent platinum molds currently available. *Assumes a 1ml : 1.4g recipe ratio. Since weight is a metric of a recipe's specific density, we cannot exactly determine the weight of your specific recipe. Please consult the designated volume (ml) specification above to calculate a more exact weight (g) reading. All Dark City Gold Standard SOPs yield a 1ml : 1.4g ratio. Mold Specifications Sizes Avaliable (Volume) Shape Pieces Per Mold Weight Material Options Mold Dimensions Compatibility Square Molds 2.5mL Square 134 3.5g Rose Pro Series, Translucent 280mm x 392mm Hand Fill, Flood & Scrape, Universal Depositor 2.85mL Square 234 3.5g Rose Pro Series, Translucent 290mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 3.57mL Square 120 5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 4mL Square 192 5.6g Rose Pro Series, Translucent 290mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 6mL Square 165 8.4g Rose Pro Series, Translucent 391.6mm x 286.5mm Hand Fill, Flood & Scrape, Universal Depositor Cube Molds 1mL Cube 609 1.5g Rose Pro Series, Translucent 286mm x 398mm Hand Fill, Flood & Scrape, Universal Depositor 1.6mL Cube 275 2.2g Rose Pro Series, Translucent 289mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor 2.2mL Cube 209 3g Rose Pro Series, Translucent 289mm x 365mm Hand Fill, Flood & Scrape, Universal Depositor, Baker Perkins ServoForm Mini 3.4mL Cube 280 4.8g Rose Pro Series, Translucent 275.9mm x 394.7mm Hand Fill, Flood & Scrape, Universal Depositor Triangle Molds 2.66mL Triangle 210 3.7g Rose Pro Series, Translucent 280mm x 379.7mm Hand Fill, Flood & Scrape, Universal Depositor 2.8mL Tetrahedron 95 3.9g Rose Pro Series, Translucent 135mm x 374mm Hand Fill, Flood & Scrape, Universal Depositor 4.1mL Triangle 160 5.7g Rose Pro Series, Translucent 285mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor Multidose Molds 2.25mL Cube 144 3.2g Rose Pro Series, Translucent 254mm x 355mm Hand Fill, Flood & Scrape, Universal Depositor 3.3mL Rhombus 209 4.6g(each segment: 2.3g*) Rose Pro Series, Translucent 284mm x 375.4mm Hand Fill, Flood & Scrape, Universal Depositor 4mL Square 165 5.5g Rose Pro Series, Translucent 289mm x 380mm Hand Fill, Flood & Scrape, Universal Depositor 12.5mL Rectangle 60 17.5g Rose Pro Series, Translucent 279.3mm x 385.2mm Hand Fill, Flood & Scrape, Universal Depositor 23.5mL Square Rope 20 32g (each segment: 3.2g*) Rose Pro Series, Translucent 258mm x 385mm Hand Fill, Flood & Scrape, Universal Depositor 42.4mL Rectangle 18 59.4g Rose Pro Series, Translucent 240.9mm x 381.3mm Hand Fill, Flood & Scrape, Universal Depositor Cube Molds 1mL Cube 609 15.g Rose Pro Series, Translucent 286mm x 398mm Hand Fill, Flood & Scrape, Universal Depositor 1.6mL Cube 275 2.2g Rose Pro Series, Translucent 289mm x 384mm Hand Fill, Flood & Scrape, Universal Depositor 2.2mL Cube 209 3g Rose Pro Series, Translucent 289mm x 365mm Hand Fill, Flood & Scrape, Universal Depositor 3.4mL Cube 280 4.8g Rose Pro Series, Translucent 275.9mm x 394.7mm Hand Fill, Flood & Scrape, Universal Depositor Coin Mold 2.5mL Coin 120 3.5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 2.17mL Coin 176 3g Rose Pro Series, Translucent 289mm x 374mm Hand Fill, Flood & Scrape, Universal Depositor 2.5mL Coin 120 3.5g Rose Pro Series, Translucent 276mm x 387mm Hand Fill, Flood & Scrape, Universal Depositor 3.26mL Coin 165 4.6g Rose Pro Series, Translucent 289mm x 385mm Hand Fill, Flood & Scrape, Universal Depositor 7.1mL Puck 88 9.9g Rose Pro Series, Translucent 283.2mm x 390.2mm Hand Fill, Flood & Scrape, Universal Depositor 7.1mL (Bit) Coin 88 9.9g Rose Pro Series, Translucent 280.2mm x 386.1mm Hand Fill, Flood & Scrape, Universal Depositor 34.3mL Coin 35 48g Rose Pro Series, Translucent 268.1mm x 371.7mm Hand Fill, Flood & Scrape, Universal Depositor 45.2mL Coin 20 63.3g Rose Pro Series, Translucent 293.0mm x 365.3mm Hand Fill, Flood & Scrape, Universal Depositor Gum Drop 1.3mL Gum Drop 388 1.82g Rose Pro Series, Translucent 286mm x 390mm Hand Fill, Flood & Scrape, Universal Depositor 2.15mL Gum Drop 176 3g Rose Pro Series, Translucent 289mm x 392mm Hand Fill, Flood & Scrape, Universal Depositor 3.6mL Gum Drop 140 5g Rose Pro Series, Translucent 259mm x 363.6mm Hand Fill, Flood & Scrape, Universal Depositor
$150.00 - $250.00
Diamond Sauce Separator Basket Dutch Weave 100 Micron
BVV Diamond Sauce Separator Baskets for your Diamond Sauce Separator sold "A la Carte" The 6" long basket fit the BVV DSS-9 The 8.25" long basket fit the BVV DSS-12 The basket is a Dutch Weave all 304 Stainless Steel basket, and fits inside a 3" tri-clamp spool. The lip perfectly fits the tri clamp flange and works with our Dutch Weave product line gaskets.
$21.00 - $26.00
Diamond Sauce Separator for 1.9 ft³ Ovens and Larger
BVV Diamond Sauce Separator The BVV diamond sauce separator is a good compliment to any diamond miner. With this vessel you can easily strain and separate your diamonds from the sauce using the internal basket. You can clean your diamonds like never before with less work. DSS-9 12.25" Exact Height (Fits 1.9 ft³ Vacuum Ovens) 6" Deep Basket (100 micron mesh Dutch Weave) 3"x9" Main Body Spool DSS-12 15.25" Exact Height (Fits larger than 1.9 ft³ Vacuum Ovens) 9" Deep Basket (100 micron mesh Dutch Weave) 3"x12" Main Body Spool Replacement Top Gasket around the basket can be found Here.
$160.00 - $180.00
Dichloromethane Lab Grade 99.9%
Dichloromethane (DCM) Lab Grade Tested 99.99% Purity (Aka. Methylene Chloride) Dichloromethane is an organochloride that appears as a colorless volatile liquid having sweet chloroform-like odor. This liquid is widely used as a solvent. Although it is not miscible with water, it is polar, and miscible with most organic solvents. Commonly used for partitioning alkaloids from aqueous solutions Dichloromethane or DCM for short is commonly used as an extraction solvent across the food & beverage industry and is well known for its use in the decaffeination of coffee. With a density of 1.33g/cm3 it is denser than water partitioning as the bottom layer during liquid-liquid extraction. With a low boiling point of 39.8C/103.3F Dicholormethane allows for fast drying and the preservation of temperature-sensitive compounds. While Dichloromethane is highly volatile it is actually neither flammable nor explosive in air. Produced through the chlorination of methane along with chloromethane, trichloromethane (chloroform), and tetrachloromethane (carbon tetrachloride, Dichloromethane is the least toxic of the three. While Dichloromethane is less toxic than other chlorinated hydrocarbons it is still known to cause skin and serious eye irritation and may cause drowsiness or dizziness and potentially cancer. During handling always wear appropriate personal protective equipment in the form of tightly fitting safety goggles or face shield, long-sleeved clothing, and an approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced. Always ensure DCM is handled under adequate ventilation using a chemical fume hood. Avoid getting DCM into the eyes, on skin, or on clothing, and avoid ingestion and inhalation. Dichloromethane should always be stored in a dry, cool, and well-ventilated place with the container tightly closed. Dichloromethane Technical Data Sheet Dichloromethane Safety Data Sheet Chemical Formula: CH2Cl2 Molecular Weight: 84.93 g·mol−1 CAS Registry Number: 75-09-2 Appearance Colorless Liquid Odor: Faint, Chloroform-like Density 1.3266 g/cm3 (20 °C) Boiling Point: 39.6 °C / 103.3 °F Solubility in water: 17.5 g/L (25 °C) GHS Pictograms: GHS Signal Word: Warning GHS Hazard Statements: H315, H319, H335, H336, H351, H373 GHS Precautionary Statements P261, P281, P305+P351+P338 UN Identification Number: 1593 Proper Shipping Name: Dichloromethane Transport Hazard Class: 6.1 Packing Group: III DOT Placard: What Is Dichloromethane? Dichloromethane, also known as methylene chloride, is a colorless, volatile, and sweet-smelling organic compound with the chemical formula CH2Cl2. It is a halogenated hydrocarbon and is commonly used as a solvent in various industrial and laboratory applications. What is Dichloromethane Used for? Dichloromethane, also known as methylene chloride, is a versatile organic compound with several common uses, including: Solvent: It is widely used as a solvent in various industrial and laboratory applications. Dichloromethane's ability to dissolve a wide range of organic compounds makes it valuable in chemical processes and as a cleaning agent. Extraction: It is used in some extraction processes, such as the decaffeination of coffee and tea. It can selectively dissolve caffeine from coffee beans or tea leaves, leaving behind other flavor compounds. Chemical Reactions: It is used in chemical reactions as a solvent and as a reagent in various synthetic procedures. Pharmaceuticals: In the pharmaceutical industry, dichloromethane can be used for various purposes, including as a solvent for drug formulation. Aerosol Propellant: It has been used as a propellant in aerosol products like paints and coatings. Foaming Agent: In the production of polystyrene foam, dichloromethane can be used as a foaming agent. Lab Applications: In laboratory settings, it is used as a solvent for analytical methods, especially in chromatography. What are the Properties of Dichloromethane? Dichloromethane, also known as methylene chloride, is a colorless, volatile liquid with several notable properties: Physical State: At room temperature (around 25 degrees Celsius or 77 degrees Fahrenheit), dichloromethane exists as a volatile liquid. It has a sweet, ether-like odor. Density: The density of dichloromethane is approximately 1.33 grams per milliliter (g/mL), making it denser than water. Solubility: Dichloromethane is highly miscible with a wide range of organic solvents, including ethers, alcohols, and chlorinated compounds. It exhibits limited solubility in water, forming an azeotrope with a maximum water concentration of around 12.5%. Boiling Point: It has a relatively low boiling point of approximately 39.6 degrees Celsius (103.3 degrees Fahrenheit), which makes it volatile and easy to evaporate. Reactivity: It is relatively chemically stable under normal conditions. However, dichloromethane can react with strong bases, such as sodium hydroxide, producing potentially hazardous compounds. Flammability: Dichloromethane is not highly flammable but can burn under certain conditions, particularly if it forms a vapor-air mixture within its flammable range. Toxicity: It is considered a hazardous chemical due to its potential health risks. Inhalation of dichloromethane vapors can lead to dizziness, headaches, nausea, and, in high concentrations, more severe health effects. Prolonged exposure can be harmful. Environmental Impact: Dichloromethane is known to be an ozone-depleting substance and can contribute to stratospheric ozone depletion. Consequently, its production and use are regulated or restricted in many countries under environmental laws. Industrial Use: Despite its potential hazards, dichloromethane is used in various industrial applications, such as paint stripping, as a solvent, and in the production of some chemicals and pharmaceuticals. What Are The Hazards Of Dichloromethane? Dichloromethane (DCM), also known as methylene chloride, is a volatile organic compound that poses several hazards to human health and the environment. It's important to handle DCM with care and follow safety precautions when working with this chemical. Here are some of the main hazards associated with dichloromethane: Inhalation Hazard: DCM is a volatile chemical, and its vapors can easily be inhaled. Short-term exposure to high concentrations of DCM vapor can lead to symptoms such as dizziness, headache, nausea, and in severe cases, loss of consciousness or death. Prolonged or repeated exposure to lower concentrations may cause respiratory irritation, coughing, and chest discomfort. CNS Depression: Dichloromethane can affect the central nervous system (CNS) when inhaled or absorbed through the skin. It has mild anesthetic properties and can lead to CNS depression, resulting in impaired coordination and reaction time. Skin and Eye Irritation: DCM can irritate the skin and eyes upon contact. It may cause redness, itching, and dermatitis. Eye contact can lead to irritation, tearing, and blurred vision. Carcinogenicity: Long-term exposure to DCM has been associated with an increased risk of cancer, particularly lung cancer. The International Agency for Research on Cancer (IARC) has classified DCM as a Group 1 carcinogen to humans. Environmental Impact: DCM is an ozone-depleting substance and can contribute to the depletion of the ozone layer when released into the atmosphere. It is also harmful to aquatic life, and its disposal into water bodies can have adverse effects on the environment. Flammability: While DCM itself is not highly flammable, its vapors can form flammable mixtures with air. It is important to take precautions to prevent the buildup of flammable vapor concentrations in enclosed spaces. Chemical Reactivity: DCM can react with certain chemicals, and its contact with strong oxidizers or alkalis can result in hazardous reactions. It should be stored and handled away from incompatible substances. To minimize the hazards associated with dichloromethane, it is essential to work with this chemical in a well-ventilated area, wear appropriate personal protective equipment (PPE), including gloves and eye protection, and follow safety guidelines and regulations. Use DCM in a chemical fume hood or a well-ventilated area to reduce inhalation exposure. Proper storage, handling, and disposal procedures should also be followed to protect human health and the environment. Additionally, it is advisable to be aware of local regulations and guidelines related to the use and disposal of DCM. How Do I Use Dichloromethane Safely? Using dichloromethane (DCM), also known as methylene chloride, safely is essential to minimize health and environmental risks associated with this chemical. Here are some guidelines for the safe use of DCM: Personal Protective Equipment (PPE): Wear appropriate PPE, including chemical-resistant gloves, safety goggles or a face shield, and a lab coat or chemical-resistant apron. Consider using a chemical-resistant apron and full-body protective clothing if handling large quantities of DCM. Ventilation: Work in a well-ventilated area, such as a chemical fume hood or a well-ventilated laboratory. Avoid working with DCM in confined spaces without proper ventilation. Respiratory Protection: If working with DCM outside of a fume hood or in a space with inadequate ventilation, use a NIOSH-approved organic vapor respirator to protect against inhalation exposure. Ensure that the respirator is fit-tested and properly maintained. Storage: Store DCM in a cool, well-ventilated area away from direct sunlight, heat, and incompatible materials. Keep containers tightly closed and labeled with hazard information. Handling: Use DCM only for its intended purposes and avoid unnecessary exposure. Handle DCM with care to prevent spills or splashes. Do not eat, drink, or smoke while working with DCM. Avoid Skin and Eye Contact: Wear chemical-resistant gloves to prevent skin contact. Use safety goggles or a face shield to protect your eyes from splashes. In case of skin contact, promptly remove contaminated clothing and wash the affected area thoroughly with soap and water. In case of eye contact, flush the eyes with water for at least 15 minutes and seek immediate medical attention. Work in a Controlled Environment: Perform DCM-related tasks on stable surfaces to prevent accidental spills. Avoid working alone when handling DCM, especially in situations where immediate assistance may be needed in case of an accident. Fire Safety: DCM is not highly flammable but can form flammable vapor-air mixtures. Keep ignition sources away from DCM and store it in a cool area. Ensure that fire extinguishing equipment is readily available and that personnel are trained in its use. Emergency Procedures: Know the location of emergency eyewash stations, safety showers, and spill response kits. Establish and familiarize yourself with emergency procedures in case of spills, fires, or exposure incidents. Disposal: Dispose of DCM waste according to local regulations and guidelines. DCM waste is often considered hazardous and must be handled and disposed of properly. Training: Ensure that personnel handling DCM are adequately trained in its safe use, storage, and disposal. Regulations and Guidelines: Be aware of and comply with local, state, and federal regulations governing the use, handling, and disposal of DCM. Remember that DCM is a volatile chemical, and its vapors can be harmful when inhaled over an extended period. Follow safety data sheet (SDS) instructions, and if you are uncertain about any aspect of using DCM safely, consult with a safety professional or chemical hygiene officer in your organization.
$25.00 - $1,175.00
Digital Vacuum Chamber Gauge Upgrade *Wireless
Digital Vacuum Chamber Gauge Upgrade *Wireless After many requests, we have combined our infamous vacuum tight bulkhead with the power of a wireless vacuum gauge that can be a simple upgrade to ANY of our vacuum chamber products or resin traps. For those seeking truly accurate readings at any altitude and wireless monitoring this is the ultimate gauge for any vacuum system!. *To install: All that is required is a 1/2" wrench to remove the original and replace the digital one. The VGW-mini Wireless micron vacuum gauge measures vacuum via just one service port and with no loss of refrigerant. Its compact, robust and smart design support HVAC technicians with numerous intelligent features like the graphic display of measurement data in the Elitech Tools App. Its smart Bluetooth integration allows for data to be stored and evaluated reliably and efficiently, thus saving precious time and resources. Product Features High Accuracy The digital vacuum gauge achieves precise deep vacuum measurements down to single digit resolutions and provides notifications when the evacuation target is met. Smart APP Control Control your micron tester remotely and navigate through all measurement data via Smartphone or Tablet. Quickly and conveniently document your job, finalize your report and export - directly from the job site. Intelligent Judgement of H2O Status The vacuum meter automatically judges physical state of H2O by comparing ambient temperature and water saturation temperature corresponding to the vacuum in the system. Large, Easy-to-Read Display Continual digital readout of evacuation process can be viewed easily on the large, full-view LCD screen. Rechargeable Lithium Battery Built-in rechargeable lithium battery can work up to 20 hours per single full charge, saving troubles of frequent battery change. Product Specifications Measuring Range: 0-19000 micron Operating Temperature: -4℉~140℉ (-20°C~60°C) Interface: 1/4 SAE Accuracy: 1~10,000 microns: ±10% of readings ±10 microns10,000~19,000 microns: ±20% of readings Resolution: 0-400 1 Micron400-3000 10 Micron3000-10000 100 Micron10000-19000 250 Micron Vacuum Units microns, mTorr, in/hg, Pa, Torr, KPa, mbar and psia Battery rechargeable lithium battery (1,000mAh) Overload 27.5 bar Certification CE
$178.00
Distribution Plate - 6"
Distribution Plate - 6" The 6" distribution plate is designed to be placed above a tube in shell heat exchanger to help evenly distribute liquid around the heat exchanger. It has a borosilicate sight glass to give you a visual of flow and dispersion into the heat exchanger.
$390.00
Dk-Lok V63 Series 1/4" 10-250PSI Adjustable Pressure Relief Valve 316SS
V63 Series 1/4" 10-250PSI Adjustable Pressure Relief Valve 316SS DK-LOK® V63/66 series proportional relief valves provide a wide range of set pressures in order to protect your systems against over pressurization resulting in damage to system components. These proportional relief valves open in direct relation to how quickly the system inlet pressure overcomes the set pressure of the spring. They close in direct relation to how quickly the system inlet pressure drops below the spring set pressure. We offer a variety of connection configurations and seal materials to match your system requirements. DK-LOK V63/66 Series Pressure Relief Valve Data Sheet
$225.00
Double Neck Round Bottom Flask
Double Neck Round Bottom Flask Double Neck Round Bottom Flasks can be used for a variety of applications such as capturing and collecting material and also used for boiling off material through distillation. These flasks are double neck with a ground 24/40 joint and require the application of vacuum grease to the ground surface when using the flasks in a vacuum application. The second neck of this flask can also be used for a thermometer port or for introducing material into the flask with a glass funnel. When laying these flasks down it is always recommended to use a cork stand for the flask to prevent breakage and keep the flask upright. Sizes Available: 500ml - 24/40 Ground Joint 1000ml - 24/40 Ground Joint 2000ml - 24/40 Ground Joint *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$25.00 - $50.00
Double Seal X-Profile Oil-Resistant Buna-N O-Ring
Double Seal X-Profile Oil-Resistant Buna-N O-Ring For use with our vacuum Chambers and the fittings/valves that are used for vacuum chamber components. Specifications: Material - Buna-N Rubber Cross Section Shape - X Dash Number - 203 Width - 1/8" ID - 5/16" OD - 9/16" Hardness - Durometer 70A (Medium) For use with: Acetic Acid Ammonia Animal Oils Boric Acid Butyl Alcohol Calcium Hydroxide Citric Acid Diluted Salted Solutions Ethylene Glycol Glycerin Grease Isopropyl Alcohol Mineral Spirits Motor Oil Petroleum Fluids Phosphoric Acid Potassium Hydroxide Sodium bicarbonate Vegetable Oils Specifications Met - ASTM D2000, SAE AS568, SAE J200 Temperature Range - (-30) to 225 F
$1.50
Dry Sift Extractor
Dry Sift Extractor Transform your sifting process with the BVV Dry Sift Extractor, a revolutionary solution that streamlines the creation of high-quality sift in a fraction of the time no ice, water, or freeze dryer required. Say goodbye to the risk of mold contamination associated with traditional ice-water extractions, along with the added costs of water and ice. Opt for efficiency and speed with our Dry Sift Extractor. Designed with precision, our purpose-built Dry Sift Extractor is equipped with five mesh screens, enabling you to sort and refine your dry sift effortlessly. The inclusion of 160-micron, 120-micron, 90-micron, and 45-micron mesh screens allowing you the capability to perform static tec ensures that BVV's Dry Sift Extractor is specifically tailored to produce top-tier sift with unparalleled quality. Elevate your sifting experience and leave traditional methods behind with this innovative solution. Key Features:Optimized Sifting: designed for superior sifting performance. Its precise vibrations ensure a consistent and thorough separation of trichomes from plant material, resulting in high-quality dry sift.Durable Construction: Built to withstand the demands of continuous use, this sifter boasts a robust and durable construction. The quality materials ensure longevity, making it a reliable companion for your sift-making endeavors.User-Friendly Operation : With its intuitively designed controls and quick-release clamps, operating the sifter is a seamless experience. The user-friendly features make dry sift extraction effortless and efficient.Optimized Mesh Sizes: Complete with 160.120,90, & 45 micron screens 600mm Diameter: The generous 600mm diameter provides ample space for sifting, allowing you to process larger quantities of material efficiently. This makes the sifter ideal for commercial operations or enthusiasts seeking batch production capabilities. Specifications 600MM Diameter Screens 160,120,90,45 Micron Mesh screens 220V/1P/60Hz Footprint (DXH): 28"x41" Weight: 200lbs (312lbs Crated)
$5,000.00
Dry Utility Vacuum/Pressure Gauge - Bottom Mount
Dry Utility Vacuum/Pressure Gauge-Bottom Mount - with 1/4" brass NPT
$8.00
Dry Utility Vacuum/Pressure Gauge - Center Back Mount
Dry Utility Vacuum/Pressure Gauge - Center Back Mount 1/8" MNPT brass Connection
$12.00$7.00
Dynalene HC-50
Dynalene HC-50 Dynalene HC/Potassium Formate is a water-based, low-temperature heat transfer fluid engineered to deliver the excellent heat transfer performance in applications down to -58°F (-50°C). With the temperature range -50°C to +218°C, Dynalene HC easily exceeds the performance of other water-based chemistries such as glycol /water mixtures, calcium chloride/water as well as hydrocarbon and silicone-based fluids. The fluid comes in five concentrations and is non-toxic, non-hazardous and non-flammable. Effective Calcium Chloride Alternative Dynalene HC/Potassium Formate heat transfer fluid is an excellent alternative to calcium chloride and other brine solutions because it demonstrates a higher thermal efficiency and lower corrosion rate. This fluid, as compared to other glycols, calcium chloride, and other brine solutions, should lower the leak and spillage rate, and reduce maintenance and repair costs on refrigerated systems. This is due to Dynalene HC's use of "safe" chemistries resulting in a high level of corrosion inhibition. The viscosity of calcium chloride solutions is also noticeably higher than Dynalene HC heat transfer fluid, which in turn makes Dynalene HC a more thermally efficient solution. Key Features: 100% Biodegradeable Non-Toxic Non-flammable Aqueous-Based Superior heat transfer characteristics Attractive alternative to glycols and brines Applications: Pharmaceutical process Food and beverage Chemical process Climatic Chamber LPG Processing Low-Temperature Baths Temperature Range: Open systems: HC-50: -51°C (-60°F) to 110°C (230°F)Closed Systems: HC-50: -50°C (-58°F) to 218°C (425°F) Technical Data Sheet MSDS Engineering Guide
$120.00 - $2,900.00
Eccentric Recovery Pump Shaft Adapter
Eccentric Recovery Pump Shaft Adapter Replacement Eccentric adapters for TRS or BVV recovery pumps. Model numbers shown below- BVV-EC-TRS: TRS21 BVV-EC: BVV2CYL BVV4CYL BVVCMEP-RETRO
$80.00 - $110.00
Eco Oven PID Controller with Display Screen
Eco Oven PID Controller with Display Screen Compatible with older Orange/Black Models and newer Purple/White Models. Specifications BVV ECO Temp Range: 0-212°F Temp Accuracy: +/- 1° Built-In Calibration: Yes Temp Display Unit: C or F Timer Range: 0-999 Electrical Requirements: 110v @ 60Hz Compatible Ovens: 09ECO / 19ECO Shipping Dimensions: 5 x 5 x 5 - 1lbs SKU: ECOPID
$150.00
Eco Oven Power/LED Switch
Green Eco oven power switch.
$15.00
Eco Oven Replacement Handle
This is a replacement handle for BVV™ Eco ovens.
$45.00
ECO Oven Shelf Bracket Kit
ECO Oven Shelf Bracket Kit This bracket kit has an updated design to make it easier to slide the shelves in and out of the oven without breaking the budget.(Note: this kit only fits the Best Value Vacs 0.9CF and 1.9CF ECO Oven line)
$5.00 - $6.00
ECO Oven Shelves
ECO Oven Shelves These are stainless steel oven shelves for BVV™ ECO Ovens and fit either a 0.9CF or a 1.9CF ECO Oven. Specifications: 0.9CF - 10.9" (278mm) x 11.2" (285mm) x 1/8" Thickness 1.9CF - 14.1" (359mm) x 15.4" (392mm) x 1/8" Thickness
$32.00 - $42.00
ECO Replacement 50L Main Condenser (V1)
ECO Replacement 50L Main Condenser (V1) Replacement main condenser for ECO rotary evaporators made before 2019. 60/80 Lower Flange 40/60 Top Flange 1/2" Barb connections for cooling coil
$895.00
Economy Recirculating Heater Kit
Economy Recirculating Heater Kit The Economy Recirculating Heater Kit is designed to provide efficient heating and circulation at an affordable price. The kit includes a submersible water pump for fluid circulation, an LX or MX immersion heater, and all tubing and hose clamps needed to pair with your system. The tubing is 1/2" ID x 5/8" OD and the pump fitting is 1/2". The pump will circulate up to 594 GPH. Economy Recirculating Heater Kit Includes: Polyscience LX or MX Immersion Circulator EcoPlus Eco 633 Fixed Flow Submersible/Inline Pump 594 GPH 5 Gallon Aluminum Pot 10 Feet of 1/2" Silicone Tubing 10 Pack of Adjustable Stainless Steel Tubing Clamps
$1,700.00
You have seen 720 out of 1155 products