Pumps
UL Listed BVV™ Pro Series 21.2CFM Corrosion Resistant Two Stage Vacuum Pump
UL Listed BVV™ Pro Series 21.2CFM Two Stage Vacuum Pump (Pump holds a 1 year limited warranty) This is the BVV™ Brand 21.2CFM Two Stage Pro Series vacuum pump. The BVV™ Pro Series 21.2CFM will pull a vacuum down to 0.3 microns effortlessly. The pump is designed with corrosion resistance and long-term continuous operation in mind. Comes standard with K-25 fittings, clamps, centering rings and oil mist exhaust filter which returns trapped oil back to the pump and allows for quieter operation. Adjustable gas ballast keeps moisture, solvent, and other contaminants from getting stuck in the pump. Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Specifications Electrical Requirements: 110v 60Hz 1100 Watts Pumping Rate: 21.2CFM Ultimate vacuum without gas ballast: 0.3 micron Ultimate vacuum with gas ballast: 6 micron Inlet/Outlet connection: KF25/NW25 Flange Oil Volume: 2L/2.1 quarts Motor Rate: 1720 RPM Working Temperature: 5C to 40C Unit Dimensions: 21 x 7.5 x 12 Shipping Dimensions: 29.5 x 9.5 x 16.5 Unit Weight: 95lbs Shipping Weight: 105lbs Recommended oil: Ultragrade 19 Noise level: <58 dB CE Compliance: Yes Warranty: 1 year limited warranty Pump Warranty Information Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result in the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$3,500.00
Welch DuoSeal Vacuum Pump Oil, Gallon 1407K-15
Welch DuoSeal Vacuum Pump Oil, Gallon 1407K-15 ***Note: This item has a possible 1-2 week lead time depending on stock availability*** Welch fractionated oil for DuoSeal belt-driven pumps to ensure the highest vacuum performance. DuoSeal Oil performs to rigid standards for vapor pressure, vacuum level stability, and viscosity -the lubrication that helps enable renowned DuoSeal pump durability.
$125.00
CMEP-OL Low-Pressure Gauge
CMEP-OL Low-Pressure Gauge This is a low-pressure replacement gauge for the CMEP-OL recovery pump. Gauge readout is (-30)-0-(500)PSI.
$25.00
UL Listed BVV™ Pro Series 11.3CFM Corrosion Resistant Two Stage Vacuum Pump
UL Listed BVV™ Pro Series 11.3CFM Two Stage Vacuum Pump (Pump holds a 1 year limited warranty) This is the BVV™ Brand 11.3CFM Two Stage Pro Series vacuum pump. The BVV™ Pro Series 11.3CFM will pull a vacuum down to 0.3 microns effortlessly. The pump is designed with corrosion resistance and long-term continuous operation in mind. Comes standard with K-25 fittings, clamps, centering rings and oil mist exhaust filter which returns trapped oil back to the pump and allows for quieter operation. Adjustable gas ballast keeps moisture, solvent, and other contaminants from getting stuck in the pump. Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Specifications Electrical Requirements: 110v 60Hz 750 Watts Pumping Rate: 11.3CFM Ultimate vacuum without gas ballast: 0.3 micron Ultimate vacuum with gas ballast: 6 micron Inlet/Outlet connection: KF25/NW25 Flange Oil Volume: 1.5L/1.59 quarts Motor Rate: 1720 RPM Working Temperature: 5C to 40C Unit Dimensions: 21 x 7.5 x 12 Shipping Dimensions: 29.5 x 9.5 x 16.5 Unit Weight: 66lbs Shipping Weight: 75lbs Recommended oil: Ultragrade 19 Noise level: <58 dB CE Compliance: Yes Warranty: 1 year limited warranty Pump Warranty Information Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result in the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$2,600.00
CMEP-OL Compressor Top Cover Bearing
CMEP-OL Compressor Top Cover Bearing This is a replacement bearing for the Compressor Top Cover of the CMEP-OL and is fully encased and require no lubrication.
$45.00
CMEP-OL Fan Bearing
CMEP-OL Fan Bearing This is a replacement bearing for the fan of the CMEP-OL and is fully encased and require no lubrication.
$35.00
Welch DryFast Collegiate Diaphragm Pump 2014
DryFast Collegiate Diaphragm Pump 2014 ***Note: This item has a possible 1-2 week lead time depending on stock availability*** Product Details Chemical Resistant Oil-Free Tuneable Vacuum Welch DryFastTM PTFE Diaphragm Vacuum Pumps enable precise vacuum control for organic evaporations with exclusive Advanced Vapor Management (AVM). Oil-Free, portable, chemical resistant, 1 head diaphragm design simplifies maintenance. Choose from seven dry PTFE vacuum pump models with flows up to 70 L / min and adjustable vacuum down to 2 Torr. Economical DryFastTM vacuum pumps are perfect for tough lab applications. Model Number 2014 Applications Vacuum Filtration, SPE, Rotary Evaporations (volatile solvents <80oC B.P., volume <2 liters), pumping harsh vapors & gases, general laboratory vacuum Type Laboratory Vacuum Pump Free Air Displacement cfm (l/min.) @60Hz 1.2(35) Free Air Displacement m3/hr (l/min.) @50Hz 1.75(29) Ultimate Pressure 40(53) Maximum Vacuum 28.3 Motor Horsepower (watts) 1/5(150) Adjustable Vac. / Gas Ballast Yes Tubing Needed 1/4(7) Intake Thread NPT M14(1/8) Overall Dimensions LxWxH in. (cm) 12x7.0x8.3 (30.5x 17.8x21.1) Ship Weight 19(8.6) Shipping Carton Dimensions LxWxH in. (cm) 21x14x15 (52x35x37) Adjustable Vacuum Knob
$1,602.00
Edwards E2M28 21 CFM Dual-Stage High Capacity Vacuum Pump
Edwards E2M28 21 CFM Dual-Stage High Capacity Vacuum Pump ***Note: This item Will Ship by Freight only*** The EM range of oil‑sealed rotary pumps – renowned for their high ultimate vacuum, rapid pumping speed, quiet operation and ability to handle vapor – have become the industry standard for laboratory and light industrial applications. The pump is a freestanding unit with the drive provided through a flexible coupling by either a single‑phase or three‑phase (four pole) air cooled motor.Each EM pump is supplied with 2 x 1 liter of Ultragrade 19 oil, O ring and centering ring, two Allen keys and spares seal for oil drain and filter plugs. For PFPE prepared FX pumps Fomblin® to be ordered separately. Technology The motor is totally enclosed and is cooled by the motor-cooling fan which directs air along the motor fins. The motors are fitted with a thermal overload device. When the motor is too hot, the thermal overload device switches off the pump. The thermal overload device has an automatic reset; when the motor cools down, the device resets and the motor will restart.An oil pressure system lubricates the pump shaft bearing surfaces and rotor sealing faces. The pump has an oil distribution valve which prevents discharge of oil to the pump interior after the pump stops. The pumping chambers are air-tight, so this arrangement also prevents suckback unless the gas ballast valve is open.You can inspect the level and condition of oil in the oil box reservoir through the oil sight-glass. An oil filler-plug is fitted to the top of the oil box. The pump has two oil drain-plugs to allow either gravity oil drain or pressure oil drain. Features and Benefits The pump is designed for reliable, long‑term operation. Thermal overload device prevents overheating (single phase only). The drive is provided through a flexible coupling by a single‑phase or three‑phase (four pole) motor. The motors are totally enclosed and are cooled by the motor cooling fan. Full height O ring sealed oil sight glass for easy checking of oil level and condition. Large sight glass and operating oil range. IE3 energy efficient 3 phase motor used with E2M28. Edwards E2M28 21 CFM Dual-Stage High Capacity Vacuum Pump. The EM range of oil-sealed rotary pumps - renowned for its high ultimate vacuum, rapid pumping speed, quiet operation and ability to handle vapour - has become the industry standard laboratory and light industrial applications. The E2M28 pump is a two-stage, direct drive, sliding vane pump. The pump is oil sealed and designed for reliable, long-term operation in both laboratory and industrial environments. The pump is a freestanding unit with the drive provided through a flexible coupling by either a single-phase or three-phase (four-pole) motor. Specifications Displacement 50Hz 32.2 m3h-1 / 19 ft3min-1 60Hz 38.9 m3h-1 / 22.3 ft3min-1 Speed (Pneurop 6602) 50Hz 27.5 m3h-1 / 16.2 ft3min-1 60Hz 33.0 m3h-1 / 19.5 ft3min-1 Ultimate vacuum (total pressure) without gas ballast 1 x 10-3 mbar / 7.5 x 10-4 Torr with gas ballast 1.5 x 10-2 mbar / 1.1 x 10-2 Torr with Fomblin® 1 x 10-2 mbar / 7.5 x 10-3 Torr Inlet connection NW25 flange Outlet connection** Nozzle 15 mm external Ø removable from 3/4 in BSP tapped hole Max allowed pressure at outlet 0.5 bar gauge / 7 psig Max water vapour pumping rate – GB II 220 gh-1 Max inlet pressure for water vapour 30 mbar / 23 Torr Max water vapour pumping rate 0.7 kg h-1 Operating temperature range 13 – 40 °C Nominal rotation speed 1440 / 1720 rpm Motor power 50 Hz 0.75 kW Motor power 60 Hz 0.90 kW Power Connector 1-ph* IEC EN60320 C19 Weight 44 kg / 97 lbs Noise 57 dB(A) @ 50 Hz Oil capacity - max 1.5 litre Oil capacity - min 1.2 litre Recommended oil (supplied) Ultragrade 19 * Pumps listed with IEC connector only ** The FX are supplied with NW25 outlet connection ** POWER CORD NOT INCLUDED. RECOMMEND FOR CUSTOMER TO WIRE PUMP TO OUTLET WITH EXACT LENGTH. DO NOT USE EXTENSIONS** **RECOMMEND FOR CUSTOMER TO HAVE ELECTRICIAN WIRE PUMP TO OUTLET WITH EXACT LENGTH** Pump Warranty Information Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$8,653.00 - $10,402.00
Economy Recirculating Heater Kit
Economy Recirculating Heater Kit The Economy Recirculating Heater Kit is designed to provide efficient heating and circulation at an affordable price. The kit includes a submersible water pump for fluid circulation, an LX or MX immersion heater, and all tubing and hose clamps needed to pair with your system. The tubing is 1/2" ID x 5/8" OD and the pump fitting is 1/2". The pump will circulate up to 594 GPH. Economy Recirculating Heater Kit Includes: Polyscience LX or MX Immersion Circulator EcoPlus Eco 633 Fixed Flow Submersible/Inline Pump 594 GPH 5 Gallon Aluminum Pot 10 Feet of 1/2" Silicone Tubing 10 Pack of Adjustable Stainless Steel Tubing Clamps
$1,700.00
Harvest Right Premier Vacuum Pump
Harvest Right Premier Vacuum Pump Technical Specifications Oil: Robinair Premium High Vacuum Pump Oil or JB Industries Black Gold Vacuum Pump Oil Only DC Motor Energy Efficient Voltage: Standard, 110v, 60Hz Dimensions: 16.3″ x 6″ x 12.1″ Weight: 32lbs Noise: 52 decibels Product Comparison: Premier Oil Pump vs Standard Oil Pump Oil Changes: This new Premier Pump rarely needs to have the oil changed or filtered. The pump has a gas ballast feature that makes it so water does not stay in the oil. Because of this, the oil in the pump will be pristine and clear, even after 30 or more batches. You simply won’t need to change the oil until you have run 20 or more batches. Whereas, the oil in the Standard Vacuum Pump needs to be changed and filtered every 4 or 5 batches (when using the new 3/8 inch vacuum hose). You should only replace the oil in this pump with Robinair Premium High Vacuum Pump Oil (or with JB Industries Black Gold Vacuum Pump Oil). These may be purchased from Harvest Right, Amazon, and other locations. Do not use Dairyland vacuum pump oil in the Premier pump. Vacuum Pressure: Under cold and hot conditions the Premier Pump will pull a deeper vacuum than the Standard Pump. Under cold conditions the difference is .05 Pascal for the Premier Pump and .08 Pascal for the Standard Pump. Whereas, under warm conditions the difference is much greater: .05 Pascal for the Premier Pump and 2.05 Pascal for the Standard Pump.Hence, the Premier Pump is especially not affected by warm, ambient conditions. When temperatures rise, it will pull a vacuum far better than the Standard Pump. The Premier Pump is just not affected by outside heat. It pulls the same deep vacuum even when it is in a warm environment. Noise: The Premier Pump is substantially quieter than the Standard Pump, 52 decibels versus 64 decibels. The Industrial Pump at 52 decibels is about the same as a refrigerator. Oil Mist Filter: Both pumps come with an oil mist filter. However, the Premier Pump’s oil mist filter allows for no oil spray at all and it will last much longer. Power Use: The Premier Pump uses less power than the Standard Pump (187 watts versus 218 watts). Amperage: Under hot conditions at ultimate vacuum pressure the Standard Pump pulls 2.1 amps while the Premier Pump only pulls 1.7 amps. Hence, the Premier Pump is more efficient. Weight: The Premier Pump is easier to move around as it weighs 5 pounds less than the Standard Pump (32 lbs. versus 37 lbs.) Life: The Premier Pump is more durable and will last longer than the Standard Pump.
$795.00
KF-40 Stainless Steel FNPT End Cap
KF-40 Stainless Steel FNPT End Cap This is a FNPT KF-40 (NW40) Endcap to adapt a KF40 fitting to Female NPT Threads for 1/4", 3/8", and 1/2" NPT.
$34.00 - $39.00
Vacuubrand MD 4C NT 2.2 CFM Chemistry Diaphragm Pump 110V
Vacuubrand MD 4C NT 2.2 CFM Chemistry Diaphragm Pump 110V MD 4C NT Technical Data Sheet.pdf These three-stage diaphragm pumps are an excellent solution for continuous, oil-free pumping of non-corrosive gases. They reach an excellent ultimate vacuum of 1 mbar. All parts in contact with pumped gases and vapors are made of aluminum, stainless steel and carefully selected plastics suitable for a wide range of applications with non-corrosive gases. The new NT-series provides whisper quiet and ultra-low vibration operation, high leak tightness and improved performance. The highly flexible fabric-reinforced double diaphragm made of FKM is ideal for extended operating life. These three-stage diaphragm pumps are an excellent choice for continuous, contamination-free evacuation and pumping of non-aggressive gases at demanding vacuum conditions. They are especially suitable for applications in physics and analytics. The low ultimate vacuum makes these an attractive alternative to rotary vane pumps in many applications. Typical uses are as backing pump for turbomolecular drag pumps, and for degassing of viscous media. Performance features: Outstanding chemical resistance and superior vapor tolerance Exceptionally high performance even at low vacuum Excellent ultimate vacuum even with gas ballast Whisper quiet and very low vibration Long diaphragm life, maintenance-free drive system Technical Data Max. pumping speed 50 Hz 3.8 m3/h Max. pumping speed 60 Hz 2.5 cfm Ultimate vacuum 1 mbar / 0.75 torr Number of heads 4 Number of stages 3 Lower ambient temperature (operation) 10 °C Upper ambient temperature (operation) 40 °C Lower ambient temperature (storage) -10 °C Upper ambient temperature (storage) 60 °C Max. back pressure (abs.) 1.1 bar Anschluss saugseitig small flange KF DN 16 Outlet connection Silencer / G1/4" Rated motor power 0.25 kW Rated motor speed at 50/60 Hz 1500/1800 min-1 Protection class IP 40 Dimension L in mm 328 mm Dimension W in mm 239 mm Dimension H in mm 198 mm Weight 16.4 kg Noise level at 50 Hz, typ. 45 dBA Rated mains voltage range 1 230 V Mains frequency 1 50-60 Hz NRTL certification
$4,700.00
Upgrade Tool for TRS21 Suction Valve
Our specialized tool for use with rebuilding the head on TRS21, makes installation of new Suction Valve O-Rings much easier. Includes (5) Viton O-rings.
$18.00
Harvest Right Oil Free Pump
Harvest Right Oil Free Pump What is Included: One oil free pump. The oil free vacuum pump can be used with any size freeze dryer. They are quiet, fast, and easy to use. The Harvest Right oil free vacuum pumps do not require oil changes and do not require regular user maintenance. Overview The oil free vacuum pump can be used with any size freeze dryer. They are quiet, fast, and easy to use. The Harvest Right oil free vacuum pumps do not require oil changes and do not require regular user maintenance. Technical Specification CFM 7 Voltage Standard 110V. 60Hz Plug US 110V Intake Port 3/4 JIC flare Dimensions 19″ high x 10″ deep x 10″ wide Weight 42lbs
$1,695.00
Vacuubrand MZ 2C NT 1.4 CFM Chemistry Diaphragm Pump 110V
Vacuubrand MZ 2C NT 1.4 CFM Chemistry Diaphragm Pump 110V MZ 2C NT Technical Data Sheet.pdf Chemistry-design diaphragm pumps are an excellent solution for continuous, oil-free pumping of corrosive gases and vapors. The two-stage construction provides the advantageous combination of high pumping speed and low ultimate vacuum. All parts in contact with pumped media are made of chemically resistant fluoroplastics. Well-proven PTFE sandwich diaphragms increase reliability and extend operating life. The pump MZ 2C NT is equipped with a gas ballast valve for continuous condensate purge increasing the pumping capability of condensable vapors. This pump is our most popular chemistry diaphragm pump, and is the heart of a family of VACUUBRAND pumping systems. The NT-series features further improved performance data and superior vapor tolerance. Technical data Unit MZ 2C NT Number of heads / stages 2 / 2 Max. pumping speed at 50/60 Hz m3/h 2.0 / 2.3 Max. pumping speed at 50/60 Hz cfm 1.2 / 1.4 Ultimate vacuum (abs.) mbar/torr 7 / 5 Ultim. vac. (abs.) with gas ballast mbar/torr 12 / 9 Ambient temperature range (operation) °C 10 - 40 Ambient temperature range (storage) °C -10 - 60 Max. back pressure (abs.) bar 1.1 Inlet connection Hose nozzle DN 8-10 mm Outlet connection Hose nozzle DN 8-10 mm Rated motor power kW 0.18 Rated motor speed at 50/60 Hz min-1 1500/1800 Degree of protection IP 40 Dimensions (L x W x H) mm 243 x 243 x 198 Weight kg 11.1 Noise level at 50 Hz, typ. dBA 45 NRTL certification Canada and the USA ATEX conformity (only 230V) II 3/- G IIC T3 X Internal Atm. only Items supplied Pump completely mounted, ready for use, with manual. Accessories Rubber vacuum tubing DN 8 mm (20686001)
$2,930.00
Pump Rebuild Kits for 14.1 - 21.2 - 35.3 Pro Series Pumps
Pro Series Vacuum Pump Complete Service Kit This is a complete vacuum pump service kit for the BVV™ Pro Series 14.1, 21.2, 35.3CFM line of vacuum pumps and allows the user to completely rebuild their pump and keep it running like new.
$425.00 - $550.00
BVV 2 Cylinder Active Closed Loop Recovery Kit ITS/ETL to ANSI/ISA Certified
BVV 2 Cylinder Active Closed Loop Recovery Kit ITS/ETL to ANSI/ISA Certified (Pump comes with 1 yr. limited warranty) This is an Upgrade Kit which can be added to any one of our passive systems making it into an "Active" Closed Loop System. The Active Recovery Upgrade Kit will increase recovery times by condensing the vapor a lot faster than just a hot/cold differential. This will increase efficiency and productivity, many professionals use this method, as this drives profits. This Kit Includes the Following: BVV 2 Cylinder Butane Recovery Pump ITS/ETL to ANSI/ISA Certified BVV Large Condensing Coil 1/2" x 24" SS JIC Braided Hose (2) 1/2" x 48" SS JIC Braided Hose (2) 1/2" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV 5' HVAC Hose BVV Vacuum Tee RECOVER MORE WITH LESS BVV is proud to introduce our new and powerful line-up of Butane & Propane Recovery Pumps. Blending compact design with improved Gen III Pistons from RKMAC, this collection of pumps can help you recover 1lb. of butane every 1:40 Seconds! This pump Assembled in the USA and all the critical parts are domestically made. Finding parts wont be an issue with this pump. The piston seals are rated to 450F and the average operating temperature of the pump is 175F leading to a long service life. Certified by ITS/ETL to ANSI/ISA 12.12.01 for Use in Hazardous locations Class I & II, Division 2 and Class III, Divisions 1 & 2 environments. The computer controlled brushless DC motor operates at 3000 RMP nearly twice as fast as any other pump in its class. BVV Butane/Propane Recovery Pumps are: Process up to 10,000 lbs. of vapor recovery before rebuild Equipped with oil-less reciprocating compressors for a clean product Designed and Assembled in the U.S.A. with domestic and global parts Affordable and highly cost efficient Available in 2-Cylinder, 4-Cylinder, CMEP Retrofit Comes with a 1-year Manufacturer’s Warranty covering Hemp usage Rated universal voltage 100-240V AC 50/60 Hz 1Ph Built with high efficiency Brushless DC Motor used for variable speed control Equipped with Viton O-Ring Seals for Butane/Propane gas and oil compatibility Certified by ITS/ETL to ANSI/ISA 12.12.01 Noise level: 90.3 dB at 1m *Butane recovery results were achieved on a collection base pressure greater than 30psi and using a recovery cylinder with a pressure <10psi. A dry ice coil was used in between the output port of the pump and the recovery cylinder to condense vapor.
$2,500.00 - $2,600.00
KF-25 Stainless Steel 90 Degree Manifold
KF-25 Stainless Steel 90 Degree Manifold This 90 degree stainless steel KF-25 manifold has 2 1/4" FNPT ports and measures 10" x 7".
$65.00
Welch DuoSeal Vacuum Pump Oil, Liter 1407K-11
Welch DuoSeal Vacuum Pump Oil, Liter 1407K-11 ***Note: This item has a possible 1-2 week lead time depending on stock availability.*** Use this specially fractionated oil for DuoSeal belt-driven pumps to ensure the highest vacuum performance. DuoSeal Oil performs to rigid standards for vapor pressure, vacuum level stability, and viscosity - providing the lubrication that helps enable renowned DuoSeal pump durability.
$45.63
NEO 1.4CFM Diaphragm Pump ETL RATED
The BVV V series pumps are Ani-corrosion PTFE diaphragm vacuum pumps. The two head design operates as a two-stage pump to achieve a lower degree of vacuum. They are ideal for pumping corrosive gases and organic solvents. These pumps do not need any pump oil or other lubricants, which means less maintenance and smaller chance for cross contamination. The BVV V-40 is ETL listed to be used in laboratories and comes with a 1 year manufacturer warranty on all non consumable pieces. Model V-40 Power 110V 60Hz, 240 W Ultimate Vacuum 6 torr (8mbar) Maximum Operating Pressure 1 bar Maximum Flow 40 L/min Ambient Temperature 5 - 40°C Pump Head Material PTFE Composite Valve Material FFPM Noise <70db Dimensions 315x165x210mm Weight 10.4 kg For replacement diaphragms, click HERE
$1,950.00
BVV 4 Cylinder Active Closed Loop Recovery Kit ITS/ETL to ANSI/ISA Certified
BVV 4 Cylinder Active Closed Loop Recovery Kit ITS/ETL to ANSI/ISA Certified (Pump comes with 1 yr. limited warranty) This is an Upgrade Kit which can be added to any one of our passive systems making it into an "Active" Closed Loop System. The Active Recovery Upgrade Kit will increase recovery times by condensing the vapor a lot faster than just a hot/cold differential. This will increase efficiency and productivity, many professionals use this method, as this drives profits. This Kit Includes the Following: BVV 4 Cylinder Butane Recovery Pump ITS/ETL to ANSI/ISA Certified BVV Large Condensing Coil 1/2" x 24" SS JIC Braided Hose (2) 1/2" x 48" SS JIC Braided Hose (2) 1/2" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV 5' HVAC Hose BVV Vacuum Tee RECOVER MORE WITH LESS BVV is proud to introduce our new and powerful line-up of Butane & Propane Recovery Pumps. Blending compact design with improved Gen III Pistons from RKMAC, this collection of pumps can help you recover 1lb. Butane / 0:51 Seconds! This pump Assembled in the USA and all the critical parts are domestically made. Finding parts wont be an issue with this pump. The piston seals are rated to 450F and the average operating temperature of the pump is 175F leading to a long service life. Certified by ITS/ETL to ANSI/ISA 12.12.01 for Use in Hazardous locations Class I & II, Division 2 and Class III, Divisions 1 & 2 environments. The computer controlled brushless DC motor operates at 3000 RMP nearly twice as fast as any other pump in its class. BVV Butane/Propane Recovery Pumps are: Process up to 10,000 lbs. of vapor recovery before rebuild Equipped with oil-less reciprocating compressors for a clean product Designed and Assembled in the U.S.A. with domestic and global parts Affordable and highly cost efficient Available in 2-Cylinder, 4-Cylinder, CMEP Retrofit Comes with a 1-year Manufacturer’s Warranty covering Hemp usage Rated universal voltage 100-240V AC 50/60 Hz 1Ph Built with high efficiency Brushless DC Motor used for variable speed control Equipped with Viton O-Ring Seals for Butane/Propane gas and oil compatibility Certified by ITS/ETL to ANSI/ISA 12.12.01 Noise level: 93.0 dB @ 1m *Butane recovery results were achieved on a collection base pressure greater than 30psi and using a recovery cylinder with a pressure <10psi. A dry ice coil was used in between the output port of the pump and the recovery cylinder to condense vapor.
$2,500.00
KF-50 Stainless Steel FNPT End Cap
KF-50 Stainless Steel FNPT End Cap This is a FNPT KF-50 (NW50) Endcap to adapt a KF50 fitting to Female NPT Threads for 1/4", 3/8", and 1/2" NPT.
$30.00 - $35.00
KF-25 Stainless Steel 90 Degree Manifold - Long
KF-25 Stainless Steel 90 Degree Manifold - Long This 90 degree stainless steel KF-25 manifold has 2 1/4" FNPT ports and measures 10" x 36".
$80.00
Vacuubrand MD 1C Chemistry Diaphragm Pump
Vacuubrand MD 1C Chemistry Diaphragm Pump Chemistry diaphragm pump in action Three-stage chemistry-design diaphragm pumps are an excellent solution for continuous, oil-free pumping of corrosive gases and vapors and meet high requirements regarding ultimate vacuum. The three-stage construction provides the advantageous combination of high pumping speed and deep ultimate vacuum in a pump with a very small footprint. All parts in contact with pumped media are made of chemically resistant fluoroplastics. Well-proven PTFE sandwich diaphragms increase reliability and extend operating life. The MD 1C with gas ballast valve is optimally prepared for pumping easily condensable vapors (high boiling solvents). Three-stage chemistry diaphragm pumps are an excellent solution for applications involving corrosive gases and vapors at high vacuum requirements. Typical applications are vacuum generation at rotary evaporators, vacuum concentrators and many other laboratory applications. Due to their excellent ultimate vacuum they are the ideal solution for evaporation of high boiling solvents even with gas ballast. The MD 1C pump is the heart of a whole line of reliable chemistry pumping units. Performance features: outstanding chemical resistance and superior vapor tolerance exceptionally high performance even at low vacuum excellent ultimate vacuum even with gas ballast whisper quiet and ultra-low vibration proven long diaphragm life, maintenance-free drive system Technical Data Max. pumping speed 50 Hz 1.3 m3/h Max. pumping speed 60 Hz 0.88 cfm Ultimate vacuum 2 mbar / 1.5 torr Ultimate vacuum with gas ballast 4 mbar / 3 torr Number of heads 4 Number of stages 3 Lower ambient temperature (operation) 10 °C Upper ambient temperature (operation) 40 °C Lower ambient temperature (storage) -10 °C Upper ambient temperature (storage) 60 °C Max. back pressure (abs.) 1.1 bar Anschluss saugseitig Hose nozzle DN 8-10 mm Outlet connection Hose nozzle DN 8 mm Rated motor power 0.08 kW Rated motor speed at 50/60 Hz 1500/1800 min-1 Protection class IP 40 Dimension L in mm 316 mm Dimension W in mm 143 mm Dimension H in mm 175 mm Weight 6.9 kg Noise level at 50 Hz, typ. 45 dBA Rated mains voltage range 1 200-230 V Mains frequency 1 50-60 Hz Brochure
$3,900.00
Inland FF-10 Flushing Fluid
Inland FF-10 Flushing Fluid Inland FF-10 is a solvent free hydrocarbon flushing fluid designed to be used as part of a preventive maintenance program. Periodic use of FF-10 will enable the user to remove contaminants and particulates from within all areas of the pump without the worry of contaminating the pump with an expensive solvent Specifications FF-10 Vapor Pressure at 25ºC (torr) 2x10-4 Viscosity at 40ºC (cSt) 28 Viscosity at 100ºC (cSt) 4.5 Flash Point (ºC) 199 Fire Point (ºC) 221 Density at 25ºC (g/ml) 0.85 Inland FF-10 Flushing Fluid Safety Data Sheet SDS
$24.00 - $1,275.00
Welch ProBoost Air-Cooled Diffusion Pump
Welch ProBoost Air-Cooled Diffusion Pump Product Details Use Welch ProBoost in conjunction with a backing pump like the CRVpro to get deeper vacuum and higher flow. High Vacuum to 10⁻⁵ torr Use with high vacuum and Schlenk lines Employs air cooled diffusion pump Easy Attachment to backing pump Welch ProBoost is an air cooled gas jet pump (commonly called a diffusion pump). The gas jet is formed by directing boiling silicone vapors through a hollow cone. There are no internal moving parts. The pumping action commences when the vacuum pressure in the still (i.e. wiped film) goes below 0.2 torr (200 millitorr). On an empty, leak free still, ProBoost backed by a rotary vane pump lowers the vacuum pressure to 0.00002 torr (20x lower in pressure than a 2-stage rotary vane vacuum pump can do alone). ProBoost backed by a rotary vane vacuum pump will lower vacuum pressure to below 0.0001 torr in high vacuum and Schlenk lines. This high vacuum is invaluable to improve the results from reactions using air-sensitive compounds such as organometallics, metal amides, and hydrides. ProBoost has a built-in control board for fan and heater. When you turn on ProBoost, the fan and heater both turn on. When you turn off ProBoost, the heater turns off immediately and the fan runs for another 20 minutes to cool the pump. Specifications Maximum Pumping Speed, Air 80 l/sec Ultimate Vacuum Pressure 0.00002 torr Minimum Back Pump FAD at 60 Hz 2.8 CFM Maximum Discharge Pressure 0.2 torr Ambient Environmental Temp 10–30°C Heat-up time 7 minutes Inlet Connection NW50 Discharge Connection NW25 Silicone Oil Capacity Approximately 30 ml Cool Down Time 20 minutes Pump Dimensions, L x W x H 5.5 x 5.4 x 7.5 in Weight 5.6 lbs (2.5 kg) Download Manual
$3,099.00
Welch Premium Oil - Direct Drive Vacuum Pumps, Liter
Welch Premium Oil - Direct Drive Vacuum Pumps, Liter Description: Welch Premium Oil - Direct Drive Vacuum Pumps derived from hydrotreated base, made for high performance in vacuum pump operation at elevated temperatures. Welch Premium vacuum pump oil resists breakdown in the high RPM operation environment of direct drive pumps. Enables direct drive pumps to maintain the highest vacuum performance over time. Low vapor pressure Excellent resistance to heat Designed for direct drive vacuum pumps
$55.00
ULVAC DA-40S 1.6 Cfm Oil-Free Diaphragm Pump
ULVAC DA-40S 1.6 Cfm Oil-Free Diaphragm Pump (Please note: This item has a minimum 6 week Lead Time) This Diaphragm Dry type pump creates vacuum by reciprocate movement of rubber diaphragms. The structure of this pump makes Oil-free environment and maintenance easy. Different pumping speed and two/single stages are optional depending on your required pressure and pumping volume. Applications: Vacuum chucks, wafer and tip handling devices. Vacuum tweezers, medical appliances. Printing equipment. Automatic packing machines. Optical appliances. Specifications Unit 50Hz - 60Hz Actual Pumping Speed L/min 40 - 46 Ultimate pressure Pa 19.9 x 10^3 Motor Single phase, 100V, 60W, 4P, Capacitor run Full load current A 1.6 Weight kg 7.2 Inlet, outlet pipe diameter mm O.D. dia.9 × I.D. dia.5 (Rc 1/4) Ambient temperature °C 7 – 40 Overall dimensions mm 128(W) × 242(L) × 178(H)
$1,190.00
Master Vapor MVP Liquid Recovery Pump
Master Vapor MVP Liquid Recovery Pump THE NEW LIQUID Pumps solvent in liquid state Hydrocarbon and ethanol compatible C1D1 and 3rd party Certified Drastically increases evaporation byexpanding surface area andcreating turbulence Electric Driven FDA Food Grade Compliant MADE IN THE USA Engineering Specifications: Maximum pumping outlet pressure - 70 PSI Center Section CO2 charge range 5 to 80 PSI(10-15psi over inlet pressure recommended) CO2 Inlet Size: 1 /4 in. npt(f) Maximum Pump Speed 135 cpm (cycle per minute) Process Inlet and Outlet Size: 1 in. npt Electric Motor: Explosion proof for C101 Hazardous areas Motor Specifications: 2HP, 3,600 rpm, 60Hz Size: 18.3” x 15.4” base x 42.3” tall Weight: 173.2 lb All sales final Technical Data sheet US Metric Maximum Pumping outlet Pressure 70 PSI 0.48 MPa, 4.8 bar Center section CO2 Change range 6 to 80 PSI 0.03-0.55 MPa 0.3-5.5 bar Equipment Withstand Pressure 350 PSI 2.41 MPa, 24.1 bar Maximum CO2 Consumption <0.2 scfh <0.006 cubic meters/hour CO2 inlet size 1/4 in. npt(f) Maximum Pump Speed 135 cpm Process intel and outlet size 1 in. npt Model MVP Liquid, 3 ph, Inverter Rated Power 2 HP 1.5kW Speed 3600 rp, (60 Hz) Gear Ratio 25.85 Voltage 1-phase 208-230/460V Maximum Amperaage Load 5.2 A (230V / 2.6 A (460V) Model MVP Liquid 1PH Power 2 HP 1.5kW Speed 3600 rpm (60 Hz) Gear Ratio 25.85 Maximum Amperaage Load 5.2 A (115V / 10 A (230V) Noise Data Sound Power (measured per ISO-9614-2 88.5 dBa Sound Pressure {Tested 3.28ft (1m) From Equipment} 80.5dBa Materials Process Pressure Section and Reed Valves Stainless Steel Diaphragms Standard: FKM Fluoroelastomer Optional:PTFE Process Vapor Temperature Range FKM: -40 to 275 °F (-40 to 135 C)PTFE: +40 to 220 °F 9+4 to 104 C
$13,700.00 - $14,250.00
Inland 70 Ultra Vacuum Pump Oil (Edwards Ultragrade 70)
Inland 70 Ultra Vacuum Pump Oil This is oil is a direct replacement for Edwards Ultragrade 70 oil. Specifications Inland 70 Ultra Vapor Pressure @25°C 1x10^-7 torr Viscosity @ 40°C 72 cSt Pour Point: -10°C Flash Point: 249°C Density: 0.86 g/ml Color: Clear Inland 70 Ultra Safety Data Sheet PDF
$24.00 - $1,275.00
WELCH Self-Cleaning Vacuum System 2025
WELCH Self-Cleaning Vacuum System 2025 Product Details Automatic Self-cleaning purge maintains efficiency, extends diaphragm life Free air displacement: 35 L/min (1.2 CFM) Incremental ballast switch enables fast response to bumping / foaming Complete oil-free dry vacuum systems for rotary evaporators and concentrators. Corrosion-resistant PTFE diaphragm vacuum pump systems enable superior control and efficiency for each evaporation. Provides controlled solvent stripping in flasks up to 5 L. Use 9 torr Model 2025 for solvents with atmospheric B.P. <120o C. Includes analog gauge and vacuum regulation. Inlet and exhaust separators protect pump and lab atmosphere. Specification Model Number 2025 Applications Controlled vacuum for Rotary evaporators, Centrifugal concentrators, and other evaporative processes. Type Laboratory Vacuum Pump Free Air Displacement m3/hr (l/min.) @50Hz 1.2(34) Ultimate Pressure 1.7(28) Max Pressure PSIG (pascal) 29.5 Adjustable Vac. / Gas Ballast 1/5 Tubing Needed Yes Intake Thread NPT 1/4 Overall Dimensions LxWxH in. (cm) 13.6x12x11.3 (34.5x30.5x28.7) Ship Weight 36(16.3) Intake Catch Jar Yes Exhaust Catch Jar Yes
$3,725.00 - $3,742.00
Welch WOB-L Pump 2581
Welch-L Pump 2581 ***Note: This item has a possible 1-2 week lead time depending on stock availability.*** Product Details Economical Oil Free Adjustable Vacuum Reliable WOB-L Piston pump is perfect for many common laboratory vacuum applications. Features: Vacuum to 5 Torr (29.8"Hg). Includes Vacuum Regulator and Gauge - simple to adjust and monitor vacuum level. Inlet Water Trap - float ball rises to seal off pump from accidental ingestion of water. Muffler quiets pump and filters discharge air. For use with dry or aqueous vapor applications only. Specifications Model 2581 Free Air Displacement @ 60 Hz, cfm (L/min) 3.5 (100) Ultimate Pressure, torr 5 Motor Power, HP (kW) at 60 Hz 1/3 (0.25) Inlet (Exhaust) Connection Thread NPT 3/8 Tubing Needed, I.D. in. (mm) 1/4 (7) Weight, lbs (kg) 24.5 (11.1) Dimensions, LxWxH, in (mm) 17x7.5x12 (430x420x190) 115V Order Number 2581B-50 / 2581B-24
$2,279.00 - $2,612.00
Inland 15A Vacuum Pump Oil
Inland 15A Vacuum Pump Oil Inland 15A Vacuum Pump Oil Safety Data Sheet SDS
$24.00 - $1,750.00
Inland 56 Vacuum Pump Oil (LVO 200)
Inland 56 Vacuum Pump Oil The Inland 56 is an equivalent to the Leybold LVO 200 oil. This oil can be used in pumps specifically designed for pumps that use the Leybold LVO 200 oil. Inland 56 Vacuum Pump Oil Safety Data Sheet SDS
$30.00 - $4,700.00
Harvest Right Oil Filter Cartridges 3-Pack
Harvest Right Oil Filter Cartridges 3-Pack Details: First use: • Remove cartridge packaging, grip the top of cartridge and place into cartridge holder of Harvest Right filter. • Firmly press in cartridge until it makes a firm seal. Cartridges should be replaced after approximately 15-20 uses, or sooner, depending on the quality of the oil. Oil Filtration Directions: 1. Open the oil reservoir drain valve and allow oil to drain into your oil filter. Assure all of the oil comes out by lifting the rear of the vacuum pump slightly. 2. Wait for the oil to filter through your filtration system. 3. A small amount of water accumulates in the oil as part of each batch. When the oil is filtered, the water and oil will separate. The water will sink to the bottom of the bottle while the oil floats on top of the water. 4. Remove the water from the oil by pouring o the oil and discarding the water. Do not pour the water back into the vacuum pump. This will ultimately damage the pump. 5. Pour the filtered (or new) oil into your vacuum pump. How do I know that my filtered oil is clean for use? The best indications for cleanliness are as follows: • Oil is void of debris or particulates • Oil is not milky or chalky • Oil has clarity (the color may be yellow or amber and still have clarity) • Your vacuum pump is achieving a pressure (mTorr) suitable for freeze drying How do I know when I need to replace my oil filter? • Oil won’t drain through filter (this can happen over time as debris builds up) • Oil isn’t cleaning well (i.e. The oil continues to be milky or full of debris) What's Included: 3 pack of filter cartridges
$24.95
Harvest Right Impulse Heat Sealer
Harvest Right Impulse Heat Sealer 12″ Impulse Sealer
$129.99
Harvest Right Standard Vacuum Oil Pump 7CFM
Harvest Right Standard Vacuum Oil Pump 7CFM Technical SpecificationsVoltage: Standard 115V. 60Hz Plug: US 110V Intake Port: 3/4 JIC flare Dimensions: 10-1/2″ H x 16″ D x 5-3/4″ W Weight: 35lbs Warranty: 6 months
$295.00
Vacuubrand VARIO® chemistry pumping unit PC 3001 VARIOpro
Vacuubrand VARIO® chemistry pumping unit PC 3001 VARIOpro The PC 3001 VARIO select pumping unit precisely controls the vacuum level in order to achieve unparalleled process control. This pump is suitable for even high boiling point solvents. The integrated VACUU·SELECT controller provides an easy-to-use, application based interface that covers all common lab applications. The VACUU·SELECT controller has you covered. Use manual set-point-control for simple processes, run fully automated distillations, or create your own application with simple drag-and-drop editing. For solvent evaporation, the VACUU·SELECT controller detects solvent boiling and automatically adjusts the pump's motor speed to maintain process control. The VARIO motor speed control also makes the pump whisper quiet and provides for exceptionally long maintenance intervals. The inlet separator, made of glass with a robust protective coating, prevents particles and liquid droplets from entering the pump, preventing damage and extending pump life. And the exhaust vapor condenser allows for nearly complete recovery of solvents when used with a chilled water line or recirculating chiller for economical recycling and environmental protection. Performance features simplify lab work with the VACUU·SELECT vacuum controller with graphic user interface and predefined applications automatic boiling point detection and continuous optimization of vacuum levels for quick process times compact and powerful; superior performance even with continuous condensate purge whisper quiet and ultra low vibration eco-friendly: extremely low power consumption and efficient solvent recovery. Oil-free! CE Approval Safety Information Manual Controller Manual Manual interfaces Technical data Unit PC 3001 VARIO select Vacuum controller VACUU·SELECT Number of heads / stages 4 / 3 Max. pumping speed m3/h 2.0 Max. pumping speed cfm 1.2 Ultimate vacuum (abs.) mbar/torr 2.0 / 1.5 Ultim. vac. (abs.) with gas ballast mbar/torr 4 / 3 Ambient temperature range (operation) °C 10 - 40 Ambient temperature range (storage) °C -10 - 60 Max. back pressure (abs.) bar 1.1 Inlet connection Hose nozzle DN 6-10 mm Outlet connection Hose nozzle DN 8-10 mm Coolant connection 2 x hose nozzle DN 6-8 mm Rated motor power kW 0.16 Motor speed range min-1 200 - 3000 Protection class IP 20 Dimensions (L x W x H) mm 303 x 306 x 400 Weight kg 8.2 Noise level at 50 Hz, typ. dBA 42 ATEX conformity (only 230V) II 3/- G IIC T3 X Internal Atm. only Items supplied Pumping unit completely mounted, ready for use, with manual. Accessories Rubber vacuum tubing DN 6 mm (20686000) Rubber vacuum tubing DN 8 mm (20686001) Coolant valve VKW-B (20674220) Vent valve VB M-B (20674217) Liquid level sensor (20699908) VACUU·BUS® Y-Adapter mit Kabel 2m (20683240)
$9,700.00
Welch WOB-L System 2511
Welch WOB-L System 2511 ***Note: This item has a possible 1-2 week lead time depending on stock availability*** Product Details Use this easy system to collect waste into 1.2 Liter autoclaveable collection receiver. Includes vacuum measurement and regulation. Reservoirs are protected from overflow by float valve; inlet line hydrophobic filter further protects pump. Vacuum Pump is reliable WOB-L piston pump, perfect for aqueous vapors, buffer, and mild bleach solutions . Not for use with organic solvents / acids / bases. Model Number 2511 Applications Solution aspiration / collection; vacuum filtra Type Laboratory Vacuum Pump Free Air Displacement cfm (l/min.) @60Hz 0.39(11) Free Air Displacement m3/hr (l/min.) @50Hz 0.55(9.2) Ultimate Pressure 219(292) Maximum Vacuum 21.3 Max Pressure PSIG (pascal) 33(3.3 x 105) Motor Horsepower (watts) 1/30(25) Tubing Needed 3/16(5) Intake Thread NPT 3/16 in. Hose Overall Dimensions LxWxH in. (cm) 7.6x4.5x7.5 (19.4x11.4x19.1) Ship Weight 11.0(5) Shipping Dimensions LxWxH in. (cm) 11" x 7" x 7" (39x31x32)
$941.00
You have seen 87 out of 87 products