Products
-
L.J. Star L.J. Star SSH Series High Pressure Clamps
L.J. Star SSH Series High Pressure Clamps These high pressure clamps are part of a complete line of stainless sanitary clamps made specifically for the pharmaceutical and biotech industries, the Series SSH hygienic clamp incorporates a unique profile and two bolts for greater clamping force. Suitable for high pressure applications. The SSH high-pressure clamp is part of a complete line of hygienic clamps made specifically for the pharmaceutical and biotech industries where joint cleanliness and efficiency are of paramount importance. These stainless steel clamps are made from investment castings to produce a high quality, precision fit assembly. They are designed to provide quick access to the joint for cleaning and inspection without sacrificing safety. Replacement Bolts for L.J. Star SSH Series High Pressure Clamps. These clamps come in five sizes: 1.5, 2, 3, 4, and 6 inches. Nut Sizes for these clamps: 1.5, ,2, 3, & 4 (5/8" Nut) *6" Clamp uses 3/4" Nut. Datasheet - Series SSH (High Pressure) Sanitary Clamp
$76.38 - $222.21
-
Lab Armor Lab Armor BEAD BATH
BEAD BATH Unique DESIGN Lab Armor Bead Baths were specifically designed to work with Lab Armor Beads to optimize their performance. Uniform Temperatures With Bead Bath designed expressly for beads, temperatures are consistent and uniform everywhere in the bath. Thermal uniformity is +/-1.0 at 37ºC. Always On The bath always stays on, so you don’t have to plan around warmup times. You don’t need to worry about refilling or low water burnout because there is no water to evaporate. Lab Armor Bead Baths are up to 50% more energy efficient than a standard lab water bath. Stays Clean Lab Armor reduces the risk of contamination. Contaminated samples and reagents result in distorted data and unpredictable outcomes. Stays Organized Unlike water baths that require racks, floats, and bottleneck weights, Bead Bath naturally holds things in place without accessories. So no more floating accidents.
$2,030.42 - $3,735.86
-
Lab Armor Lab Armor Beads
Lab Armor Beads Modern Upgrade Lab Armor Beads are dry metallic beads that replace water/ice/oil/sand in baths, giving old equipment a cool, shiny, state-of-the-art upgrade. Stays clean Lab Armor eliminates water bath contamination, harmful germicides, and unpleasant maintenance. Beads are dry and naturally more resistant to microbial growth than water, and therefore, are less likely to harbor and contribute to transmitting microorganisms in the laboratory. Saves time & Money Lab Armor Beads will help you save time and money. No more hassling with emptying, cleaning, and refilling water baths. Always On The bath stays on so there is no need to plan around warm-up times. Lab Armor Beads eliminate the worry about low water burnout because there is no water to evaporate. Other benefits of using Lab Armor Beads: Cleaner working environment. Greater organization capabilities as samples are held in place. Environmentally friendly. Temperature range -80°C to 180°C. High thermal conductivity. Non-toxic, non-vaporizing, antimicrobial No daily requirement for biocides, germicides, and other cleaners. No gray water. Smooth rounded shape allows fluidity and will conform to many sizes and shapes of vessels. No Racks, floats or weights required to hold items in place. Recyclable.* Weight 4 Lbs. (1.81 kg) per Liter.
$277.76 - $1,111.04
-
Lab Dosing Gun
Lab Dosing Gun 30 Day Limited Warranty This a gun for the BVV™ Semi-Automatic Lab Dosing Gun. It comes bare bones and Includes the following: Lab Dosing Gun Replacement Spring Clip Replacement Gasket 25ml Gun 0.5-2.5ml (0.5ml Increments) 50ml Gun 1-5ml (1ml Increments) Polypropylene Barrel – Chemically Resistant to: Isopropyl Alcohol, Ethanol, Butane, Hexane, Glycerin, Glycols, Terpenes, and most Acids Lure Lock Hub for all types of size attachments Adjustable plunger tension/tightening (*for user preferred plunger action) NOTE: Does not come with Syringe Tips Please Clean Prior to first use gun does not come sterilized.
$118.05
-
Lab Dosing Gun 25 milliliter Pistol Grip (0.5ml Incremental Shots)
Lab Dosing Gun 25 milliliter Pistol Grip 30 Day Limited Warranty The BVV™ Semi-Automatic Lab Dosing Gun can is easily adjusted to fill in 0.5ml, 1ml, 1.5ml, 2ml, and 2.5ml increments. You can quickly and accurately fill your cartridges. The heated barrel has a digital controller that allows the user to set a temperature from (Room Temperature - 190°F) in increments of 1.0°F. The Filler comes ready to use, just plug it in and attach the included 14 Gauge Tip. Specifications: Polypropylene Barrel – Chemically Resistant to: Isopropyl Alcohol, Ethanol, Butane, Hexane, Glycerin, Glycols, Terpenes, and most Acids 14 Gauge lure lock needle included 110V USA Plug Adjusts from 0.5-2.5ml Shots (0.5ml increments) Lure Lock Hub for all types of size attachments Extra Barrel Plunger Gasket included Adjustable plunger tension/tightening (*for user preferred plunger action) Built-in Temperature Cutoff @190F. 5ft Power Cord 3ft Heat Cord to Control Box. Assembled weight 10oz. Cleaning: NOTE: Please Clean Prior to first use gun does not come sterilized. Cleaning the barrel and components can be done with De-limonene, other chemicals can be used, however, *The Barrel Gasket is made of Nitrile and can degrade with overexposure to chemicals like Isopropyl Alcohol. To Fill the Syringe:Advance the plunger all the way to the needle tip of the barrel. Place the needle into the Oil and pull the plunger all the way back until it stops. The barrel will be filled. Increasing the Max Temperature: The Max Temperature Setting is 190°F. To increase the temperature beyond that, the user will need to follow the included instruction to unlock and change the max temp. (Absolute Max. is 212°F) Lab Dosing Gun User Manual PDF
$340.25
-
Lab Dosing Gun Barrel 304 Grade Stainless Steel
Lab Dosing Gun Barrel 304 Stainless Steel This barrel is a direct replacement for the BVV lab doing guns with the plastic barrel. This is a barrel upgrade. If you are upgrading your barrel from a plastic one, consider also buying the pinch clamp (Pinch Clamp). Alternately a large worm drive clamp frim the hardware store could be used to replace the pinch clamp. The barrels come in two capacities 25ml and 50ml. Note: Stainless Barrel ONLY does NOT include dispensing gun
$91.66
-
Lab Dosing Gun Filler 50 Milliliter Pistol Grip (1ml Incremental Shots)
Heated Filling Gun 30 Day Limited Warranty The BVV™ Semi-Automatic Lab Dosing Gun can is easily adjusted to fill in 1ml, 2ml, 3ml, 4ml, and 5ml increments. You can quickly and accurately fill your cartridges. The heated barrel has a digital controller that allows the user to set a temperature from (Room Temperature - 190°F) in increments of 1.0°F. The Filler comes ready to use, first clean the components, plug it in and attach the included 14 Gauge Tip. Specifications: Polypropylene Barrel – Chemically Resistant to: Isopropyl Alcohol, Ethanol, Butane, Hexane, Glycerin, Glycols, Terpenes, and most Acids 14 Gauge lure lock needle included 110V USA Plug Adjusts from 1-5ml Shots (1ml increments) Lure Lock Hub for all types of size attachments Extra Barrel Plunger Gasket included Adjustable plunger tension/tightening (*for user preferred plunger action) Built-in Temperature Cutoff @190F. 5ft Power Cord 3ft Heat Cord to Control Box. Assembled weight 1lb. 8oz. Cleaning: NOTE: Please Clean Prior to first use gun does not come sterilized. Cleaning the barrel and components can be done with De-limonene, other chemicals can be used, however, *The Barrel Gasket is made of Nitrile and can degrade with overexposure to chemicals like Isopropyl Alcohol. To Fill the Syringe:Advance the plunger all the way to the needle tip of the barrel. Place the needle into the Oil and pull the plunger all the way back until it stops. The barrel will be filled. Increasing the Max Temperature: The Max Temperature Setting is 190°F. To increase the temperature beyond that, the user will need to follow the included instruction to unlock and change the max temp. (Absolute Max. is 212°F) Lab Dosing Gun User Manual PDF
$340.25
-
Large 1-Micron Refinement Filter
Large 1-Micron Refinement Filter Filter large volumes of solutions with ease with our Large 1-micron Refinement filter. complete with our 1-micron Dutch Weave sintered disk these refinement filters provide complete retention of the filter paper making it impossible for suspended particles to bypass the filter paper. Made from the highest quality 304 stainless steel parts this large refinement filter is built to last making it a great alternative to polypropylene filter trolleys. Our Large 1-Micron Refinement filter is available as a complete kit with and without the a Welch BTpro100 Diaphragm Pump. Processing Power Funnel Capacity: 22.24 Liters/5.88 Gallons Collection Capacity: 50 Liters/13.2 Gallons Specifications 12"x12" Funnel Body 12" 1um Dutch Weave Sintered Disk 12" Hemispherical Ring stand 1/2" JIC Drain Valve 50L Stainless Steel Carboy Collection base -30Hg Vacuum Gauge 1/2" JIC Vacuum Port 3/8" JIC Diptube Valve 1/4" JIC Butterfly Accessory Valve 350MM Ashless Filter Paper Silicone Gaskets
$4,027.50 - $9,443.80
-
Large Refinement Filter
The BVV™ Large Refinement Filter is a stainless steel filtration system that provides large scale, high flow filtering, with greatly improved functionality compared to a traditional Buchner filter. Utilizing a collection base for vacuum assistance and storage of material, the Refinement Filter allows for benchtop filtration with a longer lifespan and ease of use. ***Note: Unit will come with 12" Single Pin Clamps for easier assembly/disassembly. Key Features: Stainless steel design for greater thermal conductivity and improved lifespan Easy to clean and disassemble with Tri-Clamp stainless steel parts Small tabletop footprint with wide mouth design Secondary collection vessel for vacuum and storage of material Liquid dip tube for direct injection into rotary evaporator after filling Key Specifications: Large 12" Diameter x 12" Height Funnel with 12" Filtration Plate 40 Liter Collection Base 5 micron Sintered Stainless Steel Filter Disc 100 Pack of Ashless Filter Paper Dedicated 3/8" Vacuum Valve Dedicated 3/8" Dip Tube Valve Silicone gaskets with high alcohol resistance 3/8" Stainless steel hose barb connections Polycarbonate sights for easy viewing 2" Tri-Clamp Short Sight Glass for Flow Viewing Operation Instructions: Before beginning filtration, place refinement filter in freezer for best thermal conductivity Secure ashless filter paper with compression ring Place collection base on floor and connect tubing from refinement filter to to a vacuum pump Attach vacuum system to the dedicated vacuum valve Begin to pour solution into filter Close dedicated dip tube valve and start vacuum Once solution has been completely filtered, stop vacuum system and disconnect from dedicated vacuum valve Connect dedicated dip tube valve to injection valve on rotovap Begin rotovap procedure Open dedicated dip tube valve and begin injecting filtered solution into rotovap
$4,166.38
-
Large Rosin Filter Bags - 10 Pack
Large Rosin Filter Bags - 10 Pack DISCLAIMER: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances Rosin filter bags are instrumental in the rosin extraction process and will yield and help remove unwanted contaminants from your end product. By using filter bags they allow you to pack material in tighter together which allows more pressure to be created on a smaller point. Filtration levels of the bags vary from our lowest 25-micron level to our largest 220-micron level and this allows the user to have a wider selection for their application. These mesh bags are also intended to be tossed out after use because the filtration media will be clogged after usage. Key Features: Increased Yield Higher Possible Pressure Stitched seam to prevent blowouts Wide Range of Micron Levels Sizes Available (Micron): 25μm 45μm 73μm 90μm 120μm 160μm 190μm 220μm Specifications: Bag Dimensions: 5" x 7.5" Material: Nylon Seam Type: Stitched Quantity Per Pack: 10
$13.89 - $19.44
-
Lattice Clamp
Lattice Clamp This clamp will connect two lab stands/ rods perpendicular to each other to create a lattice structure to have many more mounting points on your laboratory glass.
$6.94
-
Leak Free lid Bulkhead w/ o-ring washer and lock nut
1/4" FNPT x 5/16-18 Bulkhead This bulkhead has a 1/4" FNPT threaded adapter and a 5/16-18 threaded screw adapter and is made out of nickel plated brass and comes with a buna-n O-ring, stainless steel washer, and nylon locknut.
$16.67
-
Lidocaine Hydrochloride Powder USP/DMF Grade
Lidocaine ≥97.5% Complies with USP Testing Specifications Lidocaine Hydrochloride is a white crystalline powder widely used as a local anesthetic and antiarrhythmic agent. With rapid onset and intermediate duration of action, it is commonly employed in topical formulations. Its widely used in medical, dental, and veterinary applications. Specifications: Assay: 97.5% – 102.5% Melting Range: 66°C – 69°C Water Content (H₂O): 5.0% – 7.0% Residue After Ignition: ≤ 0.1% Sulfate (SO₄): Passes Test Heavy Metals: ≤ 0.002% This pharmaceutical-grade compound is manufactured under strict quality control standards to ensure consistency, purity, and compliance with international regulatory requirements. Applications: Local anesthesia for minor surgical procedures Pain relief in topical formulations Antiarrhythmic treatment for certain heart conditions Storage: Store in a cool, dry place, protected from light and moisture. Lidocaine Hydrochloride Safety Data Sheet (SDS) Lidocaine Hydrochloride Certificate of Analysis (COA) Chemical Formula: C14H23CIN2O Molecular Weight: 270.80 g/mol CAS Registry Number: 6108-05-0 Appearance White Crystalline Powder Odor: Characteristic Density 0.984 g/mL at 25 °C Boiling Point: 159-160 °C at 2 mmHg Solubility in water: Highly Soluble GHS Pictograms: GHS Signal Word: Danger GHS Hazard Statements: H301, H302 H315, H319, H334, H335, H412 GHS Precautionary Statements P233, P260, P261, P264, P264+P265, P270, P271, P273, P280, P284, P301+P317, P302+P352, P304+P340, P305+P351+P338, P319, P321, P330, P332+P317, P337+P317, P342+P316, P362+P364, P403, P403+P233, P405, P501 UN Identification Number: None Proper Shipping Name: None Transport Hazard Class: None Packing Group: None DOT Placard: None
$19.44 - $902.72
-
Liquid Filled Vacuum Gauges - NPT Lower Mount
Liquid Filled Vacuum Gauges - NPT Lower Mount 2-1/2" Liquid Filled Pressure Gauges - Stainless Steel Case, Brass, 1/4" NPT, Lower Mount Connection Dial Size: 1-1/2", 2", 2-1/2" or 4" Dial Sizes (Crimped Casing) Accuracy: +/- 3/2/3% Scale: Dual Scale - PSI/Bar Movement: Copper Alloy* Bourdon Tube: Copper Alloy* Window: Poly-carbonate Case: Stainless Steel case for protection in harsh environments Connection: Copper Alloy Lower Mount*: 1/8" NPT for 1-1/2" dial, 1/4" NPT for 4" dialsNormal Ambient Temp: -4F to +140F (-20C to 60C) 2-1/2" Oil Filled Vacuum Pressure Gauge - Stainless Steel Case, Brass, 1/4" NPT, Lower Mount Connection, -30HG/30PSI
$38.89
-
QTests LSD QTests
LSD QTests Know your dose with the LSD QTest The LSD QTest is the world’s first quantitative LSD test kit on the market. It can tell you how many micrograms are in each square of your blotter or each drop of liquid . . . before you ingest it. Use one drop of liquid or one half a hit of blotter, then compare the color of the detection vial to the enclosed color chart. It’s that simple. Instructions Note: A paper version of these instructions comes with your order. IMPORTANT INFORMATION! – READ THIS FIRST • Use this kit at room temperature. (If stored in a refrigerator, let it warm up for one hour first.) • Perform the test on a flat surface during the daytime. • Evaluate the result in daylight immediately after the 12-minute development time. (The color can change if you wait too long.) • Use a white, letter-sized sheet of paper as a background when evaluating the color. (See section four for evaluation details.) • Read all the instructions at least once through before beginning the test. 1. BACKGROUND INFORMATION This test kit can be used to detect the active ingredient LSD-25 (lysergic acid diethylamide) and its concentration in blotter, liquid, and sugar cubes. It does not work on gel tabs. The kit does not react to 1P-LSD, 1cP-LSD, ALD-52 or ETH-LAD When testing blotter, you should only test half of a dose. The end result will tell you how many micrograms of LSD are in the entire dose.* When testing liquid LSD, use only one drop. But remember, the end result tells you how much is in two drops.** When testing sugar cubes, you need to crush and mix up the sugar first. Weigh out and test one quarter (1/4th) of the sugar, then multiply the end result by two.*** IMPORTANT! – Always shake your vial of liquid LSD (and empty and refill the dropper a few times) before dosing out a drop. Liquid LSD tends to settle at the bottom of the vial. If you forget to shake it first, you could end up accidentally ingesting a dose ten or even twenty times larger than expected. Similarly, the liquid in a vial of LSD can evaporate over time, increasing its concentration. (The LSD doesn’t evaporate away. Only the liquid evaporates.) This is particularly true with alcohol solutions, and it can happen even when the lid is tightly closed. Make sure and take this into account. Older vials that have been sitting around for many months can become more potent over time. * Each perforated square in a given sheet of blotter will typically be the same dose. This is because the entire sheet was dipped into a tray of liquid LSD, and the LSD was absorbed evenly throughout the sheet. We designed the LSD QTest so that you only need to test half of a dose (half a square of blotter), and the result will tell you how much LSD is in each full dose (each full square of blotter) belonging to the same sheet. Keep in mind if you have individual squares of blotter that are not connected to each other (i.e., if the perforation was broken when you obtained them) then they may not come from the same sheet. Only connected squares can be assumed to come from the same sheet. ** When testing one drop of liquid LSD, the result tells you how much LSD is in two drops. So remember to divide the end result in half in order to determine how much LSD is in one drop. *** When a drop of liquid LSD is individually dropped onto an absorbent medium such as a sugar cube, it does not absorb evenly. This is why you need to homogenize it before you test it (by crushing and mixing thoroughly). Also, all that sugar won’t fit into the extraction vial, so just use a quarter of it. Then multiply the end result by two to determine the amount of LSD that was originally in the entire cube. 2. PREPARING FOR THE TEST Take out all the items from your kit. Along with these instructions, you should have: • protective gloves• glass vial with screw cap (the extraction vial)• dropper vial with green lid (detection reagent)• evaluation color chart 3. PERFORMING THE TEST 3.1 First put on the enclosed nitrile gloves and wear appropriate protective clothing and safety glasses. If you wear contact lenses, remove them. The liquids in the vials contain acids which may cause skin irritation or severe eye damage. In the event you come in contact with the liquid, remove the affected clothing immediately and rinse the affected skin area with water for several minutes. In case of eye contact, rinse the affected eye with running water for several minutes. (Keep pets, especially cats, away from the testing area.) If you are testing blotter, carefully cut it in half diagonally from one corner to the other using a fine pair of scissors. If you are testing a sugar cube, put it into a small zip lock baggie. Crush it up and shake it well, then pour all of it onto a milligram scale and weigh it. Write down the total weight. Now use the same scale and weigh out one quarter (1/4th) of the total for the test. 3.2 Open the glass vial and add the half piece of blotter (or the quarter amount of sugar). If you are testing liquid LSD, just add one drop. Put the lid back on the vial, close it tightly and shake it for about one or two minutes. For blotter, let the vial rest for five minutes and then repeat the process two more times to make sure all the LSD is extracted. During the five-minute resting periods, make sure the blotter is suspended in the liquid, not stuck to the side of the glass, or to the underside of the lid. Shaking three times with a five minute resting period in between is enough to extract all the LSD even from the thickest blotter. (For thinner blotter, you don’t really need to repeat this process three times, but we suggest it anyway just to make sure.) 3.3 Open the extraction vial again and place it in a safe position. Remove the green cap from the plastic dropper vial and carefully empty the entire contents into the glass vial by squeezing it with even pressure. Put the lids back onto both vials and close them tightly. 3.4 Gently invert the glass vial four or five times to mix the reagents together and then set the vial down. In the presence of LSD, the liquid will begin turning a blue color immediately. 3.5 Wait 12 minutes for the color to completely develop. The result can then be read and interpreted using the enclosed color chart. See the next section, “EVALUATING THE RESULT,” for details. IMPORTANT! – If you see blue spots or streaks on the blotter, this indicates that not all the LSD got extracted from the blotter. In this case the result will be inaccurate. (Your LSD is actually more potent than the result indicates.) This will only happen with thicker blotter if you did not carefully follow the instructions in section 3.2 above. 4. EVALUATING THE RESULT Follow the instructions above and wait 12 minutes before evaluating the result, but do not wait much longer than 12 minutes. Set a timer. By comparing the intensity or saturation of the liquid in the vial with the enclosed color chart, you can determine the result visually. In the presence of LSD-25, the detection reagent turns bluish over time. Daytime sunlight is best suited for optimal evaluation. If using artificial light, the influence of different color temperatures may slightly change the hue. You can still perform the evaluation, but you should take this into account (e.g. high blue content in energy-saving lamps, green discoloration when using LED light from cell phones, etc). SPECIFIC EVALUATION INSTRUCTIONS • Use a white, letter-sized sheet of paper as a background.• In daylight or under bright light, hold the glass vial next to the color chart about six to eight inches in front of the white sheet of paper and look through the glass vial head on. For best results, your eyes should be fairly close to the vial, but no closer than about six to eight inches.• Now compare the color of the liquid in the vial to the color chart. The corresponding concentration of LSD listed on the color chart is twice the amount of LSD that you tested. So if you tested half a square of blotter, the concentration listed indicates the amount of LSD present in the entire square.• If you tested one drop of liquid, the corresponding result indicates how much LSD is in two drops of the liquid. (So divide the result in half to calculate how much is in one drop.)• If you tested a quarter of a sugar cube, the result tells you how much LSD is in half the sugar cube. (So multiply the result by two to calculate how much LSD was in the entire, original cube.) 5. STORAGE AND SHELF LIFE Store the reagents in the refrigerator (35° – 46° F) and out of direct sunlight for a shelf life of at least 18 months. 6. WARNINGS • Keep the kit away from children and animals.• When performing the test, wear suitable protective gloves, clothing and face/eye protection. If you wear contact lenses, remove them before using the test kit.• The liquids contained in the dropper vial consist of various acids which may cause a corrosive/irritating effect on the skin or severe eye damage/irritation. Avoid contact with the skin, eyes, mouth or clothing.• Should contact with the above listed areas occur, remove the relevant clothing immediately. Instantly rinse the affected skin areas with water for several minutes. In case of contact with the eyes, immediately rinse them with water for several minutes using both hands to keep the upper and lower eyelids open.• Substances processed with the test kit are not to be consumed!• The solution in the extraction vial is flammable. It’s just a small amount, but please don’t smoke while performing the test. 7. DISCLAIMERS • QTests are only to be used for the detection and quantification of unknown substances.• The result may not be 100% accurate. Your sample could be adulterated with one or more unknown substances that cross-react with the reagents, affecting the quantitative result.• The result does not mean your sample is safe to consume. It could still contain unwanted substances and impurities that can be harmful or even deadly.• The LSD QTest is not a substitute for laboratory analysis.• miraculix and/or Qtests.org assume no responsibility for the use or misuse of the test kit or the results. 8. DISPOSAL OF MATERIALS Check your local regulations for proper disposal of acids.
$34.65
-
M11x1.0 Regulator for Compressed Gas
Regulator for Compressed Gas Bare Regulator No output Fitting This regulator is designed to fit our compressed gas tanks. Nitrogen, Argon, Helium, Nitrogen & Hydrogen Blend, and Best Whip Nitrous Oxide cylinders. Adjustment knob Is turned on to start gas flow and set desired pressure. Turn clockwise to engages the pin and start the flow of gas. Counterclockwise will retract the pin and stop the flow of gas. Tank Connection: M11x1.0 Output Thread: 1/8" BSPP Made in Italy Regulator Max Pressure Output: 80 PSI Gauges Measure in BAR. Compatible with CO2, Nitrogen, Argon, Nitrogen-Hydrogen mix, Nitrous Oxide and Helium. *The regulator in this listing does not come with hoses, or cylinders or fitting for the output.
$149.99
-
M11x1.0 Valve Dispenser for Compressed Gas
Valve Dispenser Thread Size M11x1.0 Pushpin Valve Type Our regulators are threaded and designed to fit our compressed gas tanks. Nitrogen, Argon, Helium, Nitrogen & Hydrogen Blend, and Best Whip Nitrous Oxide cylinders. This dispenser is simply a valve that will install onto the tank and will allow you to slowly or rapidly dispense the gas. The valve has a center pin, when the knob is turned clockwise it will depress the pin in the tank slowly to dispense the gas. You can even remove the valve dispenser when not in use. Compatible with CO2, Nitrogen, Argon, Nitrogen-Hydrogen mix, Nitrous Oxide and Helium. *The valve dispenser in this listing does not come with hoses, or cylinders.
$99.99
-
M16x1 F X 1/2" NPT Stainless Steel Adapter (2 pack)
2 pack stainless steel adapter fitting with M16X1 F x 1/2" NPT This adapter will fit on 16mm x 1mm threads found on many heater and chillers made by Julabo or Huber and adapt these threads to 1/2" NPT
$131.94
-
Magnetic PTFE Stir Bar Retriever
Magnetic PTFE Stir Bar Retriever Magnetic PTFE Stir Bar Retriever is used to retrieve the stirring bar from a boiling flask. Specifications: 400mm Length Material: High Temperature PTFE
$20.83
-
Magnetic PTFE Stirring Bar - L Style - 70mm
Magnetic PTFE Stir Bar - L Style - 70mm Reduce stir bar jumping with the contoured shape of this L Style Magnetic PTFE Stir Bar. Ideal for round-bottom flask stirring applications. This 70mm L Style Magnetic Stir bar is great for round-bottom flasks above 5 liters in capacity. With its PTFE coating this Magnetic Stir Bar carries excellent solvent and temperature compatibility for a variety of applications. Specifications: L Style 70mm Length Material: High-temperature PTFE
$25.00
-
MagSil-PR® Adsorbent for Chromatography
MagSil-PR® Adsorbent for Chromatography BVV™ MagSil-PR® Adsorbent for Chromatography is an adsorbent for the separation of lipids and is a commercially prepared magnesia-silica gel. MagSil-PR® has a coarse mesh size which helps with rapid flow rate for column chromatography. It's main benefit is pesticide removal from extracted plant material and will dramatically improve the color and clarity of the material. It also has the provided benefit to bind to polar water-soluble compounds which can be filtered out through a 20-micron mesh screen. Particle Mesh Size: 60/100 BVV™ MagSil-PR® SDS
$205.54 - $2,603.99
-
SSP Corporation Male Adapter
SSP - Male Adapter SSP Instrumentation Duolok® tube fittings are designed, manufactured and quality controlled to be totally “interchangeable” with the Swagelok® brand of tube fittings. Component by component examination plainly shows the two brands as completely “componentintermixable.” The precision manufacturing of both products to stringent tolerances under rigid quality control procedures ensures the safety, performance, and reliability of service whenever Duolok® and Swagelok® component parts are mixed and used in accordance with published installation and service recommendations. Specifications: Connection Type 1 Duolok Tube Fitting Connection Size 1 Specified by User Connection Type 2 Male NPT Connection Size 2 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Duolok Pressure Rating = Tubing Rating NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!
$5.56 - $25.00
-
SSP Corporation Male Connector
SSP - Male Connector SSP Instrumentation Duolok® tube fittings are designed, manufactured and quality controlled to be totally “interchangeable” with the Swagelok® brand of tube fittings. Component by component examination plainly shows the two brands as completely “componentintermixable.” The precision manufacturing of both products to stringent tolerances under rigid quality control procedures ensures the safety, performance, and reliability of service whenever Duolok® and Swagelok® component parts are mixed and used in accordance with published installation and service recommendations. Specifications Connection Type 1 Duolok Tube Fitting Connection Size 1 Specified by User Connection Type 2 Male NPT Connection Size 2 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Duolok Pressure Rating = Tubing Rating NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!
$31.94
-
SSP Corporation Male Connector Bore Through
SSP - Male Connector Bore Through SSP Instrumentation Duolok® tube fittings are designed, manufactured and quality controlled to be totally “interchangeable” with the Swagelok® brand of tube fittings. Component by component examination plainly shows the two brands as completely “componentintermixable.” The precision manufacturing of both products to stringent tolerances under rigid quality control procedures ensures the safety, performance, and reliability of service whenever Duolok® and Swagelok® component parts are mixed and used in accordance with published installation and service recommendations. ***Note: This fitting allows the user to have the corresponding tube size completely THROUGH the connector. Specifications Connection Type 1 Duolok Tube Fitting Connection Size 1 Specified by User Connection Type 2 Male NPT Connection Size 2 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Duolok Pressure Rating = Tubing Rating NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!
$47.22
-
SSP Corporation Male Elbow
SSP - Male Elbow SSP Instrumentation TruFit® is manufactured from fully-traceable raw material to close tolerances and superior surface finishes. TruFit® provides optimal performance when installed in accordance with SSP’s recommendations and the design parameters appropriate for each type of connection – tapered thread, straight thread, and weld & braze. TruFit® components are cleaned in accordance with SSP documented work instructions using equipment calibrated to NIST standards with environmentally-safe and stable agents, ultrasonics, and heat/ temperature to remove all residual oil, grease, and loose particles. Stainless steel components are passivated to the requirements of MIL QQ-P-35 and ASTM A 967. ***Note: ALL NPT Threads REQUIRE the user to properly install the fitting by using a thread sealant to prevent leaks. Best Value Vacs recommends GAS PTFE Tape Specifications Connection Type 1 Male NPT Connection Size 1 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Working Pressure (PSIG) 1/4" - 7750 3/8" - 6800 NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!
$27.78 $19.44
-
Male Elbow
BVV™ Male Elbow BVV™ brand stainless steel parts are made with precision 304 Grade Stainless Steel and are clean and free from burrs or debris. These fittings are NPT threads (National Pipe Taper) and will compress against other Female/Male NPT threads creating a tighter and tighter connection. All NPT threads require thread sealant to create a watertight and gas-tight seal between the threads. We recommend using Yellow Gas PTFE Tape because it is rated for gases and is UL listed and it is NOT recommended to use white PTFE tape because it is not rated for gas service. **NOTE: Pre-Taped option comes from BVV Pre-taped with Yellow UL Listed Gas PTFE Tape on the Male NPT threads ONLY for a +0.50c charge per male npt end. (JIC Threads DO NOT need to be taped.) MNPT Elbows allow the user to sharply turn the flow of the system by 90 degrees allowing for more clearance or better positioning of the fitting or valve on the extraction system. BVV™ Male Elbow - Data Sheet Specifications Material 304 Stainless Steel Connection Type(s): 1/4"-18 FNPT 3/8"-18 FNPT Sizes Available: 1/4" 3/8"
$8.33
-
SSP Corporation Male Elbow Tube Fitting
SSP - Duolok Male Elbow SSP Instrumentation Duolok® tube fittings are designed, manufactured and quality controlled to be totally “interchangeable” with the Swagelok® brand of tube fittings. Component by component examination plainly shows the two brands as completely “componentintermixable.” The precision manufacturing of both products to stringent tolerances under rigid quality control procedures ensures the safety, performance, and reliability of service whenever Duolok® and Swagelok® component parts are mixed and used in accordance with published installation and service recommendations. Specifications Connection Type 1 Duolok Tube Fitting Connection Size 1 Specified by User Connection Type 2 Male NPT Connection Size 2 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Duolok Pressure Rating = Tubing Rating NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA! Dimensions A 1.06 in Bx 0.77 in By 0.92 in C 0.70 in D 0.60 in E 0.19 in F 0.56 in G 9/16 in H 1/2 in P 1/4 in T 1/4 in
$11.11 - $44.44
-
Male Hollow Stopper
Male Hollow Stopper Male Hollow Stoppers are used for capping off or plugging a female join to prevent contamination or close off a port on a glassware system. These glass stoppers are hollow on the inside and require vacuum grease to create a seal when having 2 ground surfaces touching in a vacuum application. Joint Sizes Available: 14/20 Ground Joint 24/40 Ground Joint *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$11.11 - $15.28
-
Male Luer to 1/4 NPT Male Nickle Plated Brass
Male Luer to 1/4 NPT Male, Fitting Material Brass- Nickle Plated.
$27.78
-
SSP Corporation Male Run Tee
SSP - Male Run Tee SSP Instrumentation Duolok® tube fittings are designed, manufactured and quality controlled to be totally “interchangeable” with the Swagelok® brand of tube fittings. Component by component examination plainly shows the two brands as completely “componentintermixable.” The precision manufacturing of both products to stringent tolerances under rigid quality control procedures ensures the safety, performance, and reliability of service whenever Duolok® and Swagelok® component parts are mixed and used in accordance with published installation and service recommendations. Specifications Connection Type 1 Duolok Tube Fitting Connection Size 1 Specified by User Connection Type 2 Duolok Tube Fitting Connection Size 2 Specified by User Connection Type 3 Male NPT Connection Size 3 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Duolok Pressure Rating = Tubing Rating NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA! Dimensions A 1.98 in Bx 0.77 in By 0.92 in C 0.70 in D 0.60 in E 0.19 in F 0.56 in G 9/16 in H 9/16 in P 1/4 in T 1/4 in Ax 1.06 in B 1.69 in
$41.66 $20.83
-
SSP Corporation Male Tee
SSP - Male Tee SSP Instrumentation TruFit® is manufactured from fully-traceable raw material to close tolerances and superior surface finishes. TruFit® provides optimal performance when installed in accordance with SSP’s recommendations and the design parameters appropriate for each type of connection – tapered thread, straight thread, and weld & braze. TruFit® components are cleaned in accordance with SSP documented work instructions using equipment calibrated to NIST standards with environmentally-safe and stable agents, ultrasonics, and heat/ temperature to remove all residual oil, grease, and loose particles. Stainless steel components are passivated to the requirements of MIL QQ-P-35 and ASTM A 967. ***Note: ALL NPT Threads REQUIRE the user to properly install the fitting by using a thread sealant to prevent leaks. Best Value Vacs recommends GAS PTFE Tape Specifications Connection Type 1 Male NPT Connection Size 1 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Working Pressure (PSIG) 1/4" - 7750 3/8" - 6800 NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!
$27.78 $11.11
-
Malt Extract Powder for Mushrooms Mycology
Malt Extract Powder BVV® Malt Extract Powder is a premium carbohydrate source designed for cultivating mycelium and preparing nutrient-rich growth media such as Malt Extract Agar (MEA). It provides essential sugars, amino acids, and minerals that support strong, vigorous mycelial development. Features & Benefits: 🌾 High-quality maltose source for consistent, rapid growth 🍄 Ideal for preparing Malt Extract Agar, liquid culture media, and spawn hydration solutions ⚗️ Highly soluble—dissolves easily in water for precise media formulation 🧫 Supports robust mycelial structure, uniform colonization, and reliable fruiting 🧪 Compatible with other nutrients such as peptone or yeast extract STORAGE: Cool dry conditions, sealed original package Mix: Mix: 10 gram per. 500ml Directions for Use: Mix 10g of malt extract powder per 500ml of distilled water, as a nutritional additive in your agar or liquid culture formulation. Boil and stir until powder is fully dissolved. Sterilize the mixture for 45min @15psi 250°F (121°C) in a pressure cooker or autoclave. Allow mixture to cool to approximately 122°F (50°C) *To avoid excessive condensation
$18.05 - $87.49
-
Master Vapor Pumps Master Vapor MVP Liquid Recovery Pump
Master Vapor MVP Liquid Recovery Pump THE NEW LIQUID Pumps solvent in liquid state Hydrocarbon and ethanol compatible C1D1 and 3rd party Certified Drastically increases evaporation byexpanding surface area andcreating turbulence Electric Driven FDA Food Grade Compliant MADE IN THE USA Engineering Specifications: Maximum pumping outlet pressure - 70 PSI Center Section CO2 charge range 5 to 80 PSI(10-15psi over inlet pressure recommended) CO2 Inlet Size: 1 /4 in. npt(f) Maximum Pump Speed 135 cpm (cycle per minute) Process Inlet and Outlet Size: 1 in. npt Electric Motor: Explosion proof for C101 Hazardous areas Motor Specifications: 2HP, 3,600 rpm, 60Hz Size: 18.3” x 15.4” base x 42.3” tall Weight: 173.2 lb All sales final Technical Data sheet US Metric Maximum Pumping outlet Pressure 70 PSI 0.48 MPa, 4.8 bar Center section CO2 Change range 6 to 80 PSI 0.03-0.55 MPa 0.3-5.5 bar Equipment Withstand Pressure 350 PSI 2.41 MPa, 24.1 bar Maximum CO2 Consumption <0.2 scfh <0.006 cubic meters/hour CO2 inlet size 1/4 in. npt(f) Maximum Pump Speed 135 cpm Process intel and outlet size 1 in. npt Model MVP Liquid, 3 ph, Inverter Rated Power 2 HP 1.5kW Speed 3600 rp, (60 Hz) Gear Ratio 25.85 Voltage 1-phase 208-230/460V Maximum Amperaage Load 5.2 A (230V / 2.6 A (460V) Model MVP Liquid 1PH Power 2 HP 1.5kW Speed 3600 rpm (60 Hz) Gear Ratio 25.85 Maximum Amperaage Load 5.2 A (115V / 10 A (230V) Noise Data Sound Power (measured per ISO-9614-2 88.5 dBa Sound Pressure {Tested 3.28ft (1m) From Equipment} 80.5dBa Materials Process Pressure Section and Reed Valves Stainless Steel Diaphragms Standard: FKM Fluoroelastomer Optional:PTFE Process Vapor Temperature Range FKM: -40 to 275 °F (-40 to 135 C)PTFE: +40 to 220 °F 9+4 to 104 C
$19,026.48 - $19,790.32
-
Master Vapor Pumps Master Vapor MVP Recovery Pump - 60 PSI
Master Vapor MVP Recovery Pump - 60 PSI The Master Vapor Pump Model MVP-6CFM is a certified gas recovery pump designed to operate at 60 PSI. This pump is designed specifically for LP-Gas vapor recovery and is ideal for butane or butane / propane mixtures. Engineering Specifications: Recover LP-Gas vapor at OVER 6 CFM (cubic feet per minute) Recover butane at up to 1 LB/MIN (pounds per minute) Recover and recondense butane at OVER 12 GPH (gallons per hour) Electric motor: explosion proof for C1D1 hazardous areas; rated Class I Gr C & D, Class II Gr F&G Electric motor: 1 HP, 1800 RPM, 60 HZ Pump speed: 190 CPM (cycles per minute) at 60 HZ Size: 17.0” x 19.9” base x 46” tall Weight: 182.5 lb (82.8 kg) Motor Option: Model MVP-6CFM-1PH: Single-phase: 115/208-230V, 13.4/6.7 FLA (full load amps) Model MVP-6CFM-3PH: Three-phase: 208-230/460V, 3.3/1.65 FLA, Inverter-rated Documentation: Product Manual Technical Data Sheet Features and Benefits Sheet
$13,290.76
-
Master Vapor Pumps Master Vapor MVP-150XL Diaphragm
Master Vapor MVP-150XL Diaphragm Diaphragm replacement kit for use with the MVP-150XL recovery pump. Unit of Measure: EA Height: 2 IN | 5.08 CM Length: 12 IN | 30.48 CM Width: 12 IN | 30.48 CM Volume: .167 FT3 | .005 M3 Chargeable Weight: 2.58 LBS | 1.17 KG
$569.41
-
Master Vapor Pumps Master Vapor MVP150 Explosion Proof Recovery Pump
Master Vapor MVP Recovery Pump - 150 PSI (This item may carry up to a 2-4 week lead time) (This item is limited to a maximum of 10% discount during sales) The Master Vapor Pump Model MVP-150-1PH is a certified gas recovery pump designed to operate at 150 PSI. This pump is designed specifically for LP-Gas vapor recovery and is ideal for butane or butane / propane mixtures. Please note that the standard Single Phase and Three Phase models are UL Certified and that the ATEX Three Phase is CE Certified. Engineering Specifications: Recover LP-Gas vapor at OVER 6 CFM (cubic feet per minute). Recover butane at up to 1.5 LB/MIN (pounds per minute) Recover and recondense butane at OVER 18 GPH (gallons per hour) Electric motor: explosion proof for C1D1 hazardous areas; rated Class I Gr C & D, Class II Gr F&G Electric motor: 2 HP, 3600 RPM, 60 HZ. Pump speed: 220 CPM (cycles per minute) at 60 HZ. Size: 17.0” x 19.9” base x 46” tall Weight: 182.5 lb (82.8 kg) Motor Option: Model MVP-150-1PH : Single-phase: 115/208-230V, 20/10 FLA (full load amps) - UL Certification Model Model MVP-150-3PH : Three-phase: 208-230/460V, 5.2/2.6A FLA, Inverter-rated - UL Certification Compliance Details: Compliant with NFPA and UL standards for C1D1 motors and LPG vapor recovery Meets Class 1 Division 1 hazardous area facility requirements (when installed correctly) One year manufacturer’s warranty (see Operation Manual) Made in the USA Documentation: Product Manual Technical Data Sheet Features and Benefits sheet
$17,998.77 - $18,720.94
-
Master Vapor Pumps Master Vapor Pumps - MVP Recovery Pump - XL 150 PSI
Master Vapor Pumps - MVP Recovery Pump - XL 150 PSI The Master Vapor Pump Model MVP-150XL is a certified gas recovery pump designed to operate at 150 PSI. It can handle over three times the volume of vapor as our standard MVP-150. This pump is designed specifically for LP-Gas vapor recovery and is ideal for butane or butane / propane mixtures. Please note that this model of the MVP 150 only comes with Three-phase power options available. Engineering Specifications: Recover LP-Gas vapor at OVER 18 CFM (cubic feet per minute) Recover butane at up to 4.5 LB/MIN (pounds per minute) Recover and re-condense butane between 35-50 GPH (gallons per hour) Electric motor: explosion proof for C1D1 hazardous areas; rated Class I Gr C & D, Class II Gr F&G Electric motor: 5 HP, 1800 RPM, 30 HZ Pump speed: 174 CPM (cycles per minute) at 60 HZ Size: 17.0” x 22.8” base x 46.4” tall Weight: 360.5 lb (163 kg) All sales final
$25,664.91
-
Mastercool 1/4" FNPT Vacuum Pump Exhaust Adapter
Mastercool 1/4" FNPT Vacuum Pump Exhaust Adapter This fitting allows the user to connect a 1/4" NPT fitting to the exhaust for the desired application such as a carbon exhaust filter. It is made of brass and comes with a Viton O-ring. This item will also fit VE115 Vacuum pumps
$20.83
-
Mastercool Mastercool 5 CFM Dual Stage Vacuum Pump--USA Made
The Mastercool 90065 2-Stage Vacuum Pump is durable and time-tested to stand up to the most grueling conditions and will provide years of reliable service. This model is an excellent choice for small to medium-sized systems with a 2.5 lb. to 10 lb. charge capacity. Electrical: 110V, 60 Hz Stages: 2 Free Air Displacement: 5 CFM Motor: 1/3 HP Oil Capacity: 18 oz.
$486.08 $347.20
-
Mastercool Mastercool Blue 60" HVAC Hose
This HVAC hose will fit 1/4" SAE or JIC fittings. One end of the hose has a fitting made to depress a Schrader valve within the male fitting, the other end of the hose is a standard connection.
$25.00
-
Mastercool Mastercool Manifold
Mastercool Manifold Mastercool Aluminum R12 Manifold: THE MASTERCOOL MANIFOLD IS USED IN CONJUCTION WITH BOTH OUR ACTIVE UPGRADE KIT AND OUR ICARUS RACK SYSTEMS. WHEN USED IN AN ACTIVE CLOSED LOOP RECOVERY/CIRCULATION KIT, THE MANIFOLD ALLOWS FOR CONTROL OF SOLVENT INPUT VIA EXTRACTOR INPUT ON THE LOW SIDE(BLUE GAUGE), AND RECOVERY TO YOUR SUPPLY TANK ON THE HIGH SIDE (RED GAUGE). WHEN USED WITH ONE OF OUR ICARUS RACK SYSTEMS, THE MIDDLE PORT IS CONNECTED TO A SEPERATE NITROGEN SUPPLY TANK, AND THE HIGH AND LOW SIDES ARE CONNECTED TO THE MATERIAL COLUMN AND DEWAXER TO PROVIDE PASSIVE PRESSURE ASSISTANCE FOR MOVING SOLVENT THROUGH THE SYSTEM. Mastercool is the leading manufacturer of professional quality A/C manifold gauge sets. Our manifold gauge sets are. Constructed of the finest materials and machined with precision to the highest quality standards. At Mastercool, everymanifold we build is built to last. All Mastercool gauges are color coordinated for easy refrigerant recognition. Our free floating piston valve results in less wear and tear in comparison to market standard twisting piston valves Double O-Ring allows for a much better seal resulting in less leaks SPECIFICATIONS: Aluminum Block ¼ SAE Brass Fittings 1.6 Gauge Class 80 mm Gauges Refrigerants: R1270, R290, R600a Bar, PSI, ˚C Temp. Ratings: 100˚C Pressure Ratings: High Side 800 PSI, Low Side 500 PSI Temp.: Different for each Refrigerant
$104.16
-
Mastercool Mastercool Nitrogen Pressure Regulator Kit
Mastercool Nitrogen Pressure Regulator Kit Product Description Mastercool’s new nitrogen regulator is specifically designed to meet the specifications of HVAC/R and automotive A/C systems. This single stage nitrogen regulator is used to test systems for leaks when they do not contain refrigerant. 1/4” SAE flare outlet port, with control valve, to keep pressure on the regulator at all times T-Handle for ease of pressure adjustment 63 mm (2 1/2”) gauges with guards High pressure gauge 4400 psig (300 bar) Low pressure gauge 1000 psig (70 bar)
$263.87
-
MasterCool Vacuum Pump Activated Carbon Exhaust Filter
Carbon Exhaust Filter for MasterCool Pumps Replaces Koby Junior (US Patent# 3169112A) MasterCool Vacuum Pump Activated Carbon Filter for use with Mastercool pumps. This filter will adsorb contaminants such as oil aerosols, oil vapors, certain other hydrocarbon vapors, and trace moisture. They also trap all foreign solid particles and bacteria down to 0.5 microns in size. Key Features: Purifies Exhaust Gases from Vacuum Pumps Up to 19 CFM 0.5 Micron Filtration levels. Helps Maintain Safe Working Environment Adsorbs Organic Vapors and Small Particles High-Efficiency Filtration Minimal Pressure Drop Maintenance Free - Completely Disposable Pressure Safe to 90 PSI Brass M24 x 1.0 Pump Connection Filter connections 1/4" NPT Pipe Fitting Connections Removes the following contaminants: Oil Mist Oil Aerosols Oil Vapors Hydrocarbon Vapors Moisture Droplets Dust Pipe Scale Rust Fine Particles Odors Organic Aerosols Other Foreign Matter Lifespan:720 hrs. of continuous operation. (Then replacement is recommended) *NOTE PUMP NOT INCLUDED
$159.71
-
MCT Oil Coconut Based USP Food Grade
MCT Oil Coconut Based USP Food Grade 60/40 - 60%C8 / 40%C10 Soy Free, Non-GMO, Gluten Free, Dye Free, Dairy Free/Vegan Medium Chain Triglycerides (MCT’s) are fats that are naturally found in coconut and palm kernel oil. MCT’s are more easily and rapidly digested than other types of fats, as they require lower amounts of enzymes and bile acids for intestinal absorption. MCT’s are metabolized very quickly in the liver and are reported to encourage energy expenditure, and not fat storage. Numerous studies suggest that substituting MCT Oil for other fats in a healthy diet may therefore help to support healthy weight and body composition.* Suggested Usage As a dietary supplement, take 1 tablespoon (15 mL) 1 to 3 times daily. MCT Oil can also be used as a substitute for conventional oils in salad dressings, sauces or cooking as a source of beneficial fatty acids. Not recommended for use in frying due to low boiling point Caution: For adults only. MCT Oil may cause GI upset. To reduce these effects, take with food. Consult physician if pregnant/nursing, taking medication, or have a medical condition. Keep out of reach of children. Storage Guidance: Store in a cool, dry and dark environment in a tightly sealed original container. After opening, product can be refrigerated or stored at cool room temperature. Please note*** These statements have not been evaluated by the Food and Drug Administration. This product is not intended to diagnose, treat, cure or prevent any disease. BVV MCT Oil - COA BVV MCT Oil - SDS
$38.89 - $3,055.35
-
QTests MDMA QTests (Advanced)
MDMA QTests (Advanced) Know your dose with the MDMA QTest The MDMA QTest (Basic and Advance) is the first and only quantitative MDMA test kit on the market for ecstasy and molly. This single-use kit can tell you the potency of MDMA powder or crystals, or how many milligrams of MDMA are in a pressed ecstasy tablet. Use only a small amount, then compare the color of the detection vial with the enclosed color chart. It’s that simple. Rule out Counterfeit Pills As our advanced MDMA kit, it also comes with two smaller, confirmation tests. Together they can detect counterfeit samples containing amphetamine, methamphetamine, caffeine, MDA (or MDA-MDMA combinations), PMA, PMMA or 2C-B. Note: If you already know for sure that you have MDMA, you do not need the advanced kit to determine the potency. You can buy our less expensive Basic MDMA QTest. Instructions Note: A paper version of these instructions comes with your order. IMPORTANT INFORMATION! – READ THIS FIRST • Use this kit at room temperature. (If stored in a refrigerator, let it warm up for one hour first.) • Perform the test on a flat surface during the daytime. • Evaluate the result in daylight immediately after the 12-minute development time. (The color can change if you wait too long.) • Use a white, letter-sized sheet of paper as a background when evaluating the color. (See section four for evaluation details.) • This kit should only be used on pills, powders and crystals. It does not work on liquids. • Read all the instructions at least once through before beginning the test. 1. BACKGROUND INFORMATION This test kit can be used to detect the active ingredient MDMA and its concentration in powders, crystals and pills, including pressed tablets of any color. In addition, it can detect counterfeit samples that contain amphetamine, methamphetamine, caffeine, PMA, PMMA or 2C-B. 2. PREPARING FOR THE TEST Take out all the items from your kit. Along with these instructions, you should have: • protective gloves• thin glass vial with black lid (extraction vial)• large glass vial with white lid (detection vial)• small glass vial containing orange liquid with red lid (negative confirmation vial)• small glass vial containing orange liquid with blue lid (positive confirmation vial)• plastic dropper bottle with green lid• pipette• evaluation color chart You will also need a milligram scale and either a small funnel or a creased piece of paper to carefully pour the measured powder or crystals into the extraction vial. (You can make your own paper funnel. Google it!) 3. PERFORMING THE TEST 3.1 First put on the enclosed nitrile gloves and wear appropriate protective clothing and safety glasses. If you wear contact lenses, remove them. The liquids in the vials contain acids which may cause skin irritation or severe eye damage. In the event you come in contact with the liquid, remove the affected clothing immediately and rinse the affected skin area with water for several minutes. In case of eye contact, rinse the affected eye with running water for several minutes. Perform the test either outdoors or in a well-ventilated area and avoid inhaling the fumes, which can cause dizziness. (Keep pets, especially cats, away from the testing area.) 3.2 Using a milligram scale, carefully weigh out 30 mg of powder or crystals. If you are testing a pressed ecstasy tablet, use 50 mg. You can either scrape off 50 mg from the edge of the tablet using a sharp knife, or even better, crush and mix the entire tablet and then weigh out 50 mg of the resulting powder. IMPORTANT! – If you are testing a pressed ecstasy tablet, weigh the entire tablet first and write down the result. You will need to know the total weight of the tablet in order to calculate how much MDMA it contains after testing 50 mg. 3.3 Insert the extraction vial (with the black lid) into the leftmost hole in the provided cardboard box insert. This secures the vial in an upright position so it doesn’t accidentally fall over. Next, open the lid and use a funnel or creased piece of paper to carefully pour in the 30 mg of powder or crystals (or 50 mg if testing a pressed tablet). Put the lid back on the vial and close it tightly. Remove the vial from the insert hole and shake it for approximately one minute until all the soluble components have dissolved, then put it back into the hole and wait a few minutes for the insoluble components to settle to the bottom. Meanwhile, open the three remaining glass vials and place them into their corresponding holes in the cardboard box insert. IMPORTANT! – Don’t confuse the small glass vials after removing the colored lids. We suggest putting the small vial with the blue lid (the positive confirmation vial) on the far right, and the vial with the red lid (the negative confirmation vial) just to the left of one with the red lid. 3.4 Open the extraction vial again, gently remove it from the hole and look at it carefully. You will notice two distinct sections of liquid, one floating above the other. Using the pipette, you are going to collect liquid from the lower section. First, squeeze the top of the pipette to create a vacuum, then insert it into the vial until the bottom tip of the pipette is in the middle of the lower section of liquid. Now release pressure on the pipette and liquid will be drawn up into it. Be careful not to pick up any deposits or crumbs from the very bottom of the vial. Remove the pipette from the vial. 3.5 Drop two drops from the pipette back into the extraction vial to clear any debris that might have collected in the tip. Then, holding the pipette vertically (straight up and down), add three drops of liquid into each of the three glass vials (the large detection vial and the two confirmation vials). There should be plenty of liquid in the pipette to complete this step, but if it looks like you are going to run out of liquid, get some more by repeating step 3.4 above. Return any leftover liquid inside the pipette back into the extraction vial and put the pipette somewhere safe and out of the way. Then tightly close the lid again. Put the white lid back onto the large detection vial and shake it several times to mix the ingredients. The color change will begin happening soon and will take 12 minutes to complete. Set a timer. 3.6 While waiting for the color change to finish, open the plastic dropper bottle with the green lid and add 12 drops of the liquid to each of the two small glass vials. Close the vials tightly with the correct colored lids and invert each two or three times to mix the ingredients. 3.7 After waiting 12 minutes, remove the three glass vials from the cardboard holes to observe the color changes. See the next section, “EVALUATING THE RESULT,” for details. 4. EVALUATING THE RESULT Follow the instructions above and wait 12 minutes before evaluating the result. For the large detection vial, evaluate the result immediately after 12 minutes. 4.1 HOW TO EVALUATE THE LARGE DETECTION VIAL If there is no color change: If the liquid in the large detection vial has not changed color at all, that means there is no detectable MDMA (or MDA) in your sample. However, other unknown substances may be present. If the color changes, but it’s not purple: This means your sample is not pure MDMA and it might not contain MDMA at all (or MDA). Use the back-side of the color chart (step 1) to see some things that it might contain. For example, green indicates 2C-B. Yellow/orange indicates amphetamines. Other shades could indicate other drugs or mixtures of drugs. If the color changes purple: This indicates the presence of MDMA, MDA or both. You can tell which is the case by evaluating the two small confirmation vials. Do that first (section 4.2 below), then come back to finish the rest of this section (section 4.1). After confirming that your sample contains MDMA (section 4.2 below), you can determine the concentration of MDMA by comparing the intensity of the purple color in the large detection vial with the enclosed color chart. Follow the instructions below. • Use a white, letter-sized sheet of paper as a background.• In daylight or under bright light, hold the glass vial next to the color chart about six to eight inches in front of the white sheet of paper and look through the glass vial head on. For best results, your eyes should be fairly close to the vial, but no closer than about six to eight inches.• Now compare the color of the liquid in the vial to the color chart. The color bars on the chart correspond to the amount of MDMA that was in the sample you tested.• If you tested 30 mg of powder or crystal and the color matches the 16 mg color bar, you know that your sample is approximately 50% pure (i.e., it contains 16 mg of MDMA for every 30 mg of powder/crystal.)• If you tested 50 mg from an ecstasy tablet, divide the total weight of the tablet by 50 and then multiply by the result. This will tell you how many milligrams of MDMA were in the original tablet. For example, if your tablet weighed 460 mg, and the result shows 16 mg of MDMA in the 50 mg portion that you tested, you know there was approximately 147.2 mg of MDMA in the original tablet (460 ÷ 50 = 9.2 and 9.2 x 16 = 147.2). 4.2 HOW TO EVALUATE THE SMALL CONFIRMATION VIALS If the large detection vial turned purple, that means your sample contains either MDMA, MDA or both. Evaluate the small vials to determine which is the case. Follow these instructions. (You can also use the back side of the color chart.) • If the vial with the red lid (the negative confirmation vial) turns red, that strongly indicates the presence of MDA. If it stays the original orange color, that indicates no MDA is in the sample.• If the vial with the blue lid (the positive confirmation vial) turns a strong purple/blue, that indicates the presence of MDMA. If it does not change color or turns slightly pink (and if the vial with the red lid turned red) that confirms the presence of MDA.• If the vial with the red lid turns slightly reddish and the vial with the blue lid turns purple, that indicates the presence of both MDMA and MDA. 4.3 EXPECTED RESULTS If the large vial shows a clear purple color, the vial with the red lid remains the original orange color, and the vial with the blue lid shows a clear purple/blue color change (like the image above), this indicates MDMA is present, and the substance is probably not contaminated with amphetamines, MDA or PMA. In this case, go back up to step 4.1 and assess the concentration of MDMA in your sample. (Note: there is always the possibility that small amounts of any substance could be present, just not enough to affect the coloration.) 4.4 UNEXPECTED RESULTS If the large vial turns purple, the vial with the red lid turns red, and the vial with the blue lid shows no color change (or turns slightly pink), the sample contains MDA rather than MDMA. It might also contain other substances. If both small vials show a color change, this indicates a mixture of MDA and MDMA. Either way, it is no longer possible to determine the concentration. Other unexpected results can also occur. Here are some possibilities and what they likely indicate: 1. If the large vial turns green and the small vial with the red lid turns red, this strongly indicates the presence of 2C-B. 2. If the large vial turns yellow/orange and the small vial with the red lid turns red, this strongly indicates the presence of amphetamines. In this case, if the small vial with the blue lid turns purple/blue, this indicates the presence of either caffeine or methamphetamine. 3. If the large vial does not change color and the small vial with the red lid turns red, this strongly suggests the presence of PMA. But if the small vial with the blue lid turns blue, then it suggests PMMA rather than PMA. 4. If you see a mixture of different colors, this indicates the presence of one or more unknown drugs. Even if none of the vials change color, the sample still could contain unknown substances. 5. STORAGE AND SHELF LIFE Store the reagents in the refrigerator (35° – 46° F) and out of direct sunlight for a shelf life of at least 6 months. 6. WARNINGS • Keep the kit away from children and animals.• When performing the test, wear suitable protective gloves, clothing and face/eye protection. If you wear contact lenses, remove them before using the test kit.• Perform the test outdoors or in a well-ventilated area and avoid inhaling the fumes, which can cause dizziness.• The liquids contained in the test kit consist of various acids which may cause a corrosive/irritating effect on the skin or severe eye damage/irritation. Avoid contact with the skin, eyes, mouth or clothing.• Should contact with the above listed areas occur, remove the relevant clothing immediately. Instantly rinse the affected skin areas with water for several minutes. In case of contact with the eyes, immediately rinse them with water for several minutes using both hands to keep the upper and lower eyelids open.• Substances processed with the test kit are not to be consumed! 7. DISCLAIMERS • QTests are only to be used for the detection and quantification of unknown substances.• The result may not be 100% accurate. Your sample could be adulterated with one or more unknown substances that cross-react with the reagents, affecting the quantitative result.• The result does not mean your sample is safe to consume. It could still contain unwanted substances and impurities that can be harmful or even deadly.• The MDMA QTest is not a substitute for laboratory analysis.• miraculix and/or Qtests.org assume no responsibility for the use or misuse of the test kit or the results. 8. DISPOSAL OF MATERIALS Check your local regulations for proper disposal of acids.
$48.54
-
QTests MDMA QTests (Basic)
MDMA QTests (Basic) Know your dose with the MDMA QTest The MDMA QTest is the first and only quantitative MDMA test kit on the market for ecstasy and molly. This single-use kit can tell you the potency of MDMA powder or crystals, or how many milligrams of MDMA are in a pressed ecstasy tablet. Use only a small amount, then compare the color of the detection vial with the enclosed color chart. It’s that simple. This Kit is Only for Determining Potency This is our Basic MDMA QTest, which means it is only for detecting potency. It cannot tell you whetherwhether you have MDMA to begin with. Only buy this kit if you already know you have MDMA. Many companies sell qualitative test kits for detecting MDMA. You may want to use one of those first. However, you can also buy our Advanced MDMA QTest that comes with two smaller, confirmation tests. That kit will tell you whether you actually have MDMA, and also detects counterfeit samples containing amphetamine, methamphetamine, caffeine, MDA (or MDA-MDMA combinations), PMA, PMMA or 2C-B. Instructions Note: A paper version of these instructions comes with your order. IMPORTANT INFORMATION! – READ THIS FIRST• Make sure you have real MDMA before using this kit. If you have MDA, 6-APB or 5-MAPB instead, the kit will produce a similar reaction, but it won’t be accurate. Many companies sell multi-use MDMA test kits that give qualitative results (just not quantitative). Use one of those kits first, or buy our Advanced MDMA QTest. • Use this kit at room temperature. (If stored in a refrigerator, let it warm up for one hour first.) • Perform the test on a flat surface during the daytime. • Evaluate the result in daylight immediately after the 12-minute development time. (The color can change if you wait too long.) • Use a white, letter-sized sheet of paper as a background when evaluating the color. (See section four for evaluation details.) • This kit should only be used on pills, powders and crystals. It does not work on liquids. • Read all the instructions at least once through before beginning the test. 1. BACKGROUND INFORMATION This quantitative test kit can be used to detect the concentration of MDMA in powders, crystals and pills (including pressed tablets of any color) that have first been verified to contain MDMA. (Use a qualitative MDMA test kit first to make sure you have MDMA, or buy our Advanced MDMA QTest, which contains two extra qualitative tests.) 2. PREPARING FOR THE TEST Take out all the items from your kit. Along with these instructions, you should have: • protective gloves• thin glass vial with black lid (extraction vial)• large glass vial with white lid (detection vial)• plastic dropper bottle with green lid• pipette• evaluation color chart You will also need a milligram scale and either a small funnel or a creased piece of paper to carefully pour the measured powder or crystals into the extraction vial. (You can make your own paper funnel. Google it!) 3. PERFORMING THE TEST 3.1 First put on the enclosed nitrile gloves and wear appropriate protective clothing and safety glasses. If you wear contact lenses, remove them. The liquids in the vials contain acids which may cause skin irritation or severe eye damage. In the event you come in contact with the liquid, remove the affected clothing immediately and rinse the affected skin area with water for several minutes. In case of eye contact, rinse the affected eye with running water for several minutes. Perform the test either outdoors or in a well-ventilated area and avoid inhaling the fumes, which can cause dizziness. (Keep pets, especially cats, away from the testing area.) 3.2 Using a milligram scale, carefully weigh out 30 mg of powder or crushed crystals. If you are testing a pressed ecstasy tablet, use 50 mg. You can either scrape off 50 mg from the edge of the tablet using a sharp knife, or even better, crush and mix the entire tablet and then weigh out 50 mg of the resulting powder. IMPORTANT! – If you are testing a pressed ecstasy tablet, weigh the entire tablet first and write down the result. You will need to know the total weight of the tablet in order to calculate how much MDMA it contains after testing 50 mg. 3.3 Open the thin extraction vial (with the black lid) and use a funnel or creased piece of paper to carefully pour in the 30 mg of powder or crystals (or 50 mg if testing a pressed tablet). Put the lid back on the vial and close it tightly. Shake the vial for approximately one minute (or until all the soluble components have dissolved), then put it down and wait a few minutes for the insoluble components to settle to the bottom. 3.4 Open the large detection vial (with the white lid) and set the lid down next to it. Now open the extraction vial again (with the black lid) and look at it carefully. You will notice two distinct sections of liquid, one floating above the other. Using the pipette, you are going to collect liquid from the lower section. First, squeeze the top of the pipette to create a vacuum, then insert it into the vial until the bottom tip of the pipette is in the middle of the lower section of liquid. Now release pressure on the pipette and liquid will be drawn up into it. Be careful not to pick up any deposits or crumbs from the very bottom of the vial. Remove the pipette from the vial. 3.5 Drop two drops from the pipette back into the extraction vial to clear any debris that might have collected in the tip. Then, holding the pipette vertically (straight up and down), add three drops of liquid into the large detection vial. There should be plenty of liquid in the pipette to complete this step, but if it looks like you are going to run out of liquid, get some more by repeating step 3.4 above. Return any leftover liquid inside the pipette back into the extraction vial and put the pipette somewhere safe and out of the way. Then tightly close the lids on both vials. Now pick up and shake the large detection vial several times to mix the ingredients. The color change will begin happening soon and will take 12 minutes to complete. Set a timer. After waiting 12 minutes, you can evaluate the result. See the next section, “EVALUATING THE RESULT,” for details. 4 EVALUATING THE RESULT Follow the instructions above and wait 12 minutes before evaluating the result. Evaluate the result immediately after 12 minutes. Comparing the intensity of the purple color with the enclosed color chart. Follow the instructions below. • Use a white, letter-sized sheet of paper as a background.• In daylight or under bright light, hold the glass vial next to the color chart about six to eight inches in front of the white sheet of paper and look through the glass vial head on. For best results, your eyes should be fairly close to the vial, but no closer than about six to eight inches.• Now compare the color of the liquid in the vial to the color chart. The color bars on the chart correspond to the amount of MDMA that was in the sample you tested.• If you tested 30 mg of powder or crystal and the color matches the 16 mg color bar, you know that your sample is approximately 50% pure (i.e., it contains 16 mg of MDMA for every 30 mg of powder/crystal.)• If you tested 50 mg from an ecstasy tablet, divide the total weight of the tablet by 50 and then multiply by the result. This will tell you how many milligrams of MDMA were in the original tablet. For example, if your tablet weighed 460 mg, and the result shows 16 mg of MDMA in the 50 mg portion that you tested, you know there was approximately 147.2 mg of MDMA in the original tablet (460 ÷ 50 = 9.2 and 9.2 x 16 = 147.2). IMPORTANT! – If the liquid in the vial does not turn purple, or if it turns a color other than purple, then your sample does not contain MDMA. This likely means you forgot to test your sample with a qualitative test kit first. Even if it turns purple, if you didn’t test it first with a qualitative test kit, you don’t know if it contains MDMA. (It might contain MDA, 6-APB or 5-MAPB instead.) Always use a qualitative test kit first, or buy our Advanced MDMA QTest, which contains two other qualitative tests. 5. STORAGE AND SHELF LIFE It is always best to store any reagents in the refrigerator (35° – 46° F) and out of direct sunlight for the longest shelf life, but the ones in this MDMA kit can be stored at room temperature and should last at least 18 months. 6. WARNINGS • Keep the kit away from children and animals.• When performing the test, wear suitable protective gloves, clothing and face/eye protection. If you wear contact lenses, remove them before using the test kit.• Perform the test outdoors or in a well-ventilated area and avoid inhaling the fumes, which can cause dizziness.• The liquids contained in the test kit consist of various acids which may cause a corrosive/irritating effect on the skin or severe eye damage/irritation. Avoid contact with the skin, eyes, mouth or clothing.• Should contact with the above listed areas occur, remove the relevant clothing immediately. Instantly rinse the affected skin areas with water for several minutes. In case of contact with the eyes, immediately rinse them with water for several minutes using both hands to keep the upper and lower eyelids open.• Substances processed with the test kit are not to be consumed! 7. DISCLAIMERS • QTests are only to be used for the detection and quantification of unknown substances.• The result may not be 100% accurate. Your sample could be adulterated with one or more unknown substances that cross-react with the reagents, affecting the quantitative result.• The result does not mean your sample is safe to consume. It could still contain unwanted substances and impurities that can be harmful or even deadly.• The MDMA QTest is not a substitute for laboratory analysis.• miraculix and/or Qtests.org assume no responsibility for the use or misuse of the test kit or the results. 8. DISPOSAL OF MATERIALS Check your local regulations for proper disposal of acids.
$34.65
-
Media Bros Media Bros -CRY+ FILTER MEDIA
Media Bros -CRY+ FILTER MEDIA CRY+ is our largest granule size. With a mesh size of 16-x30, this media allows operators to run high-flow processes while maintaining a consistent quality output. DESCRIPTION: CRY+™ Filtration Media: High-Flow, High-Efficiency Filtration CRY+™ is our premium filtration media, designed with a larger granule size (16-30 mesh) to deliver unmatched flow rates without compromising the quality of your extraction. Whether you're processing high volumes or working with challenging biomass, CRY+™ ensures consistent, effective results in every run. Engineered for operators who demand speed and precision, CRY+™ is ideal for high-flow processes where residence time and color remediation are key. With a recommended solvent ratio of 6:1 to 10:1 and the ability to operate at room temperature or below -10°C without clogging, CRY+™ offers flexibility and efficiency for modern extraction setups. Key Features: Larger Granule Size (16-30 mesh): Delivers faster flow rates while maintaining purification performance. Needle Valve Recommended: Fine-tune flow rates for optimal color correction, especially when processing dark or oxidized material. Temperature Resilience: Performs optimally at sub-zero temperatures without clogging. Technical Specs: Use a 4-6” diameter CRC column for best results. Recommended operating pressure: 20-45 psi. Media ratio: 200-300g per 1 lb of biomass. Available Exclusively Through Our Dealer NetworkFind a dealer near you to purchase CRY+™: *A needle valve is recommended on the output (bottom) of the filtration column to properly fine-tune your flow rates. If you are processing dark or oxidized material, a tighter flow restriction will increase residence time, allowing for better color correction. TECHNICAL SPECS Solvent Type Hydrocarbon Color Remediation Level Moderately Heavy/High Pesticide Remediation Level Medium Selectivity/Polarity Level Moderately Selective/Medium Polarity Heavy Metal Remediation Yes Moisture Remediation Level Moderate Fats/Lipids/Waxes Level Medium Crystal Growth Fast Depth Filtration No Flow Rate High Flow pH Level Neutral (pH 7) Best For Fresh Frozen, Nugs, High Quality Suitable for Reruns Yes Distillation Clean-up Moderate Scrub SDS
$124.99 - $1,249.91
-
Media Bros Media Bros CR2 Filter Media
CR2 Filter Media Achieving optimal results in supercritical (CO2) extraction requires superior filter media. Enter CR2™ inline filter media. DESCRIPTION Achieving optimal results in supercritical (CO2) extraction requires superior filter media. Enter CR2™ inline filter media. Designed specifically for CO2 extraction, CR2™ is a non-toxic, non-reactive blend of naturally occurring zeolites. Its unique formulation gives it a high adsorption capacity, effectively removing undesirables in CO2 extracts. Like CRX™, CR2™ Filter Media is also designed to handle high flow rates. It exhibits full particle retention even under the demanding high psi conditions present in CO2 extraction. This feature ensures that your CO2 extraction process runs efficiently without compromising the quality of the extract. One common complaint about CO2-extracted products is the so-called "CO2 taste," which can be off-putting for consumers. CR2™ Filter Media tackles this issue head-on, eliminating this bitter taste and ensuring that the final product has greater purity, aesthetic appeal, and consistency. The effect of CR2™ Filter Media on the ‘CO2 taste’ in extracted products can be a game-changer for product quality and consumer satisfaction. All extractors hate baking their filter media or cleaning out caked-on media from their equipment. CR2™ Filter Media does not clog or damage CO2 systems, ensuring smooth operation and longevity of your extraction setup. It was designed by CO2 extraction operators for CO2 operators, so you can focus on extraction rather than worrying about handling issues. Like all of our premium filter media, CR2™ is non-toxic and non-reactive. Nobody should have to wear a HAZMAT suit during CO2 extraction. Using basic safety procedures, our media is organic, natural, and safe to handle. We understand that different operations have different needs, so we provide CR2™ Filter Media in various packages: a 2.5 kg pouch, an 18 kg bucket, and a 200 kg drum. Whether you run a small-scale operation or a large extraction facility, there is a packaging option to suit your needs. FDA GRAS Approved 100% Natural TECHNICAL SPECS Solvent Type CO2 Color Remediation Level Moderately Heavy/High Pesticide Remediation Level Low Selectivity/Polarity Level Moderately Selective/Medium Polarity Heavy Metal Remediation Yes Moisture Remediation Level Low Fats/Lipids/Waxes Level Low Crystal Growth Fast Depth Filtration No Flow Rate High Flow pH Level Neutral (pH 7) Best For Slightly Aged Biomass, Medium Quality Suitable for Reruns No Distillation Clean-up Moderate Scrub
$41.66 - $2,777.59
You have seen 1056 out of 1655 products