Products
-
Jacketed Hemispherical Reducers with 2" Tri-Clamp Drain Port
Jacketed Hemispherical Reducers with 2" Tri-Clamp Drain Port Jacketed Hemispherical Reducers allow the user to circulate water around the bowl and keep extracted material liquefied for easier flow through the bottom port. These jacketed reducers have 1/2" FNPT ports on either side for circulation and a 2" Tri-Clamp port through the bottom of the dish. These reducers are made out of 304 stainless steel with a high polish interior. Specifications Material 304 Stainless Steel Connection Type(s): 12" Tri-Clamp 2" Tri-Clamp (2) 1/2" FNPT
$534.71
-
Jacketed Reactor with Motor and Collection Vessel
Jacketed Reactor with Motor and Collection Vessel This jacketed reactor kit includes your choice of a C1D1 motor, standard motor, or non-electric air powered motor (air compressor required). If using an electric motor it will require wiring to the included speed controller. Using the jacketed reactor to heat your solution, use your reactor to mix your solution during the heating process. The condenser and collection vessel allow you to recover residual solvents up to 100L. The collection vessel includes a dip tube to empty the vessel and a 1/4" JIC flare to input pressure into the base to assist in emptying the tank through the dip tube. This system does NOT include a heater or chiller, please inquire with your account representative for recommendations based on your application! Jacket connections are 1/2" hose barbs. Mixer Type Pneumatic Electric C1D1 Electric Horsepower 3/4 HP 3/4 HP 1 HP Power Air Compressor 120V 220V 1ph Reactor Size 150L Collection Size 50L / 100L Jacket Connections 1/2" Hose Barb
$9,388.73 - $19,721.88
-
Jacketed Splatter Platters
Jacketed Splatter Platters Fully Jacketed splatter platters are a huge step up from normal splatter platters by providing the user a more efficient recovery of their solvent without having to move or lift the extractor into a hot water bath. These jacketed splatter platters allow the circulation of water through the outer jacket through 2x 1/2" FNPT offset ports on each side of the splatter platter. ***Note: Edges of Jacket may be rounded instead of flat. Sizes Available: 6" 8" 10" 12" Specifications: Material 304 Stainless Steel Standard 3A High Polish Connection Type(s): Tri-Clamp 1/2"-14 FNPT BVV™ Jacketed Splatter Platters - Drawing
$208.33 - $319.44
-
Jacketed Stainless Steel LP Tank with Internal Condensing Coil and Dip Tube
Jacketed Stainless Steel LP Tank with Internal Condensing Coil and Dip Tube (This item will ship via Freight ONLY) Jacketed Stainless Steel LP tanks offer a superior way to decrease contamination of solvent and feature a tri-clamp lid with a high-pressure clamp. This allows easy access to the inside of the tank, making clean out simple, unlike a normal carbon steel LP tanks. These tanks feature an exterior jacket to allow the user to circulate fluid around the outside of the tank while having an internal condensing coil on the inside of the tank to help condense hot vapors. Lids come configured with 3 valves, compound gauge and hose barbs for the internal condensing coils to help condense hot solvent vapor when the recovery stage of the extraction process is started. These tanks come with 1/4" FNPT valves and 1/4" 37 Degree JIC Flares with one port being connected to a dip tube. To avoid contamination of your solvent, the Jacketed Stainless Steel LP Tank is a simple and professional option to reduce cleaning time. Our tri-clamp lid with a high-pressure clamp makes it easy to open up the system and fully clean it out in between uses. The exterior jacket circulates fluid around the outside of the tank which the internal condensing coil condenses hot vapors. These tanks come with 1/4" FNPT valves and 1/4" (or 3/8") 37 Degree JIC Flares with one port being connected to a dip tube. If you are not using the jacket to circulate a chilling fluid, the jacket should be evacuated of all air and closed off. This is also known as a vacuum jacket, it will help to keep the fluid inside the tank at the set temperature and not transfer any temperature with the atmosphere around it. *Tank does not come with solvent Butane Capacity Calculation: All solvent tanks sold by Best Value Vacs have their capacity determined by this calculation and are based on industry standard nomenclature of the water weight tank # system because the specific gravity of water is 1.000 and the DOT 80% fill guideline. Example: 100# Tank = ~100lbs of water weight, Halfton Tank = 1000lbs of water weight. Tank # Water Weight in Lbs Specific Gravity of Butane 0.601 80% Fill Guideline 0.800 (Tank #) * (Specific Gravity of Butane) * ( 80% Fill Guideline) Sizes Available: 25# 50# 100# Specifications Tank/Component Material 304 Stainless Steel Gasket Material BUNA-N Standard 3A High Polish Connection Type(s) 1/4" (7/16-20) x 37° JIC Hose Barb Lid Connection Type(s): Tri-Clamp 1/4"-20 FNPT Hose Barb Butane Capacity: 25# 12.424 50# 24.040 100# 48.080 ***Disclaimer: These are not DOT rated tanks and are not recommended for transportation when filled.
$1,180.54 - $2,013.85
-
Jacketed Sucker Pot
Jacketed Sucker Pot This jacketed sucker pot works perfectly as a collection base for extracted oil and easy discharge or as a storage vessel for distillate dispensing. Both of these applications are made easier with the use of a heater running through the jacket. This pot can be mounted to an extraction rack with the use of 8" pipe hangers. Connections: Top: 6" Tri-Clamp Bottom: 1/2" FNPT Jacket: 1/4" FNPT (2x ports)
$416.66
-
Jacketed Sucker Pot with Ring Stand
Jacketed Sucker Pot with Ring Stand This jacketed sucker pot works perfectly as a collection base for extracted oil and easy discharge or as a storage vessel for distillate dispensing. Both of these applications are made easier with the use of a heater running through the jacket. Connections: -Top: 6" Tri-Clamp -Bottom: 1/4" FNPT -Jacket: 1/4" FNPT (2x ports)
$694.43
-
King Kone JT Tray - 60mm Cones
JT Tray - 60mm Cones This tray top is an additional attachment sold separately. It measures to be 60mm to accommodate the JT sized cones. It still will do 169 cones in one run just like the other cone accessories we offer. All you need to do to use this accessory is swap it out with the original trays on the packing machine, load your cones, and start the packing process. You can also use additional accessories like the metering tray or the packing fingers to help make the process of packing your cones more efficient.
$520.82
-
Julabo Julabo Adapter M16x1 f to NPT 1/2″
Julabo Adapter M16x1 f to NPT 1/2″ 2 Adapters M16x1 f. to NPT 1/2″ m.
$291.66
-
Julabo Julabo C2 Thermal Bath Fluid - 10 Liters
Julabo C2 Thermal Bath Fluid JULABO Thermal bath fluids are ideally suited for all of your temperature control applications and guarantee safe and reliable operation. Choosing the proper bath fluid is critical for best results in temperature control. Viscosity, oxidation characteristics and heat transfer of Thermal fluids are specifically matched with each JULABO temperature control unit. C2 Thermal Bath Fluid Product Data Sheet C2 Thermal Bath Fluid SDS JULABO Thermal bath fluids have been carefully selected and are optimized for maximum performance with JULABO instruments. Benefits Low toxicity Low viscosity High stability Minimum odor Good heat conductivity Low corrosion tendency Wide temperature ranges Technical Data Order no. 10 liters 8891400 Working temperature (°C) -90...+60 Flash point (°C) > +75 Fire point (°C) > +430 Viscosity (kinematic at 20 °C in mm²/s) 2 Density (at 20 °C in g/cm³) 0.873 Pour point (°C) -120 Boiling point (°C) 229 Ignition temperature (°C) 430 Color clear
$2,316.63
-
Julabo Julabo C5 Thermal Bath Fluid - 10 Liters
Julabo C5 Thermal Bath Fluid JULABO Thermal bath fluids are ideally suited for all of your temperature control applications and guarantee safe and reliable operation. Choosing the proper bath fluid is critical for best results in temperature control. Viscosity, oxidation characteristics and heat transfer of Thermal fluids are specifically matched with each JULABO temperature control unit. C5 Thermal Bath Fluid SDS C5 Thermal Bath Fluid Product Data Sheet JULABO Thermal bath fluids have been carefully selected and are optimized for maximum performance with JULABO instruments. Benefits Low toxicity Low viscosity High stability Minimum odor Good heat conductivity Low corrosion tendency Wide temperature ranges Technical Data Order no. 10 liters 8891402 Working temperature (°C) -60...+110 Flash point (°C) > +135 Fire point (°C) > +443 Viscosity (kinematic at 20 °C in mm²/s) 5 Density (at 20 °C in g/cm³) 0.918 Pour point (°C) -100 Boiling point (°C) >205 Ignition temperature (°C) 443 Color clear
$2,936.06
-
Julabo Julabo CORIO CD-BC6 Heating Circulator - New In Stock
Julabo CORIO CD-BC6 Heating Circulator The new generation of laboratory circulators for routine work and standard tasks CORIO™ heating circulators feature professional technology for high standards. These units facilitate internal temperature control in the bath tank or control of externally connected applications. Your advantages Models for internal and external applications Bright, white, easy to read display Very quiet Easy pump change-over between internal and external circulation USB connection High-quality bath tanks made of stainless steel with bath lid and drain tap Integrated cooling coil for counter-cooling Technical Data Order No. 9012506 Model series CORIO Category Heating Circulators Working temperature range (°C) +20 ... +150 Temperature stability (°C) ±0.03 Setting / display resolution 0.01 – 0.1 °C Temperature Display LED Heating capacity (kW) 1 Pump capacity flow rate (l/min) 15 Pump capacity flow pressure (psi) 5.08 Bath opening/bath depth (W x L / D inch) 5.1 x 5.9 / 7.8 Pump connections M16x1 Barbed fittings diameter (inner dia. / mm) 8 / 12 Filling volume (litres) 4.5 ... 6 Ambient temperature 5...40 °C Dimensions W x L x H (inch) 9.5 x 17.4 x 18.5 Weight (LBS) 22.1 Included with each unit 2 each barbed fitting for tubing 8 and 12 mm inner dia.(pump connections M16x1 male) Cooling Coil integrated Bath tank Stainless steel Bath cover integrated
$6,806.83
-
Julabo Julabo Thermal C10
Julabo Thermal C10 JULABO Thermal bath fluids are ideally suited for all of your temperature control applications and guarantee safe and reliable operation. Choosing the proper bath fluid is critical for the best temperature control results. Viscosity, oxidation characteristics and heat transfer of Thermal fluids are matched specifically with each JULABO temperature control unit. JULABO Thermal bath fluids have been carefully selected and optimized for maximum performance with JULABO instruments. Thermal C10 is a clear 10 cSt silicone fluid rated for use in open bath JULABO units with a working temperature range of -20…+160 °C. Care should be taken to observe atmospheric moisture condensation in the bath fluid with prolonged sub-ambient operation in humid environments. Water and silicone fluids are not miscible. Operation at the maximum temperature for heating applications will result in vapor formation. Vapor formation at elevated temperatures is a normal occurrence for silicone fluids. The upper temperature limit of the fluid is lower than the fluid flashpoint.
$2,216.63 - $4,402.70
-
KF Clamps
KF Clamps Clamp for standard High Vacuum flanges. Size Available: KF-16 KF-25 KF-40 KF-50
$25.69
-
KF Connection Braided Stainless Steel Bellow Hose
KF Connection Braided Stainless Steel Bellow Hose This KF or (NW) bellow hose is made out of 304-grade stainless steel with braided exterior which allows a high vacuum to be obtained with a large flow diameter for vapors. These bellow hoses are flexible and allow the user to connect a KF flanged vacuum pump to a KF flanged vacuum oven or any other application using adapters. Sizes Available: KF-16 KF-40 KF-50 Lengths Available: 20" 40"
$83.33 - $229.16
-
KF Flange x FNPT Adapter
KF Flange x FNPT Adapter KF- or NW Vacuum fittings are designed for Ultra-High-Vacuum applications and are made out of 304 stainless steel. These fittings require a special gasket with metal centering ring to not allow over compression of the gasket. These fittings have female NPT threads that come in a variety of sizes, Female NPT threading which require thread sealant if they are installed to another NPT adapted fitting.
$30.56 - $51.39
-
KF Flange x Tri-Clamp End Cap Adapter
KF Flange x Tri-Clamp End Cap Adapter These 304 stainless steel adapters allow you to adapt from a KF (NW) type flange to a Tri-Clamp sanitary flange. This part can be used for vacuum lines or even adapting to a distillation setup.
$58.33
-
KF Hand Needle Valve - Nitrogen Tested
KF Hand Needle Valve This 90 degree valve has a KF (NW) High Vacuum Flange to adapt to any other KF type pump or manifold if needed. Sizes available include KF16, KF25, KF40, and KF50. It is made out of 304 stainless steel with Viton seals. This valve is not meant for precise flow control.
$312.49
-
KF High Vacuum Stainless Steel Flange x Female Joint Adapter
This unique adapter allows the user to adapt a KF25 or KF40 High Vacuum Flange fitting to a male ground joint glass fitting and it is made out of 304 stainless steel.
$52.78
-
KF O-ring
KF O-ring O-ring features a depth stop for clamping with Viton O-ring also fits the following high vacuum connections. NW16 NW25 NW40 NW50
$10.42 - $25.00
-
KF Sight Glass
These 4 piece sight glasses can hold high vacuum levels on a system with KF connections. The housing is made of 304 stainless steel with a viton x-profile seal. The glass is tempered, impact resistant glass that increases the longevity of the sight glass. The connection sizes available are: KF25 (NW25) KF40 (NW40) KF50 (NW50) *Light assembly may be required with a 5/64" Allen wrench. Before assembly, a light application of vacuum grease on the gasket is recommended.
$102.78 - $155.55
-
KF Solid End Caps
KF Solid End Caps This is a solid KF Endcap to cap of any size port when needed Size Available: NW16 NW25 NW40 NW50
$16.67 - $20.83
-
KF Stainless Steel Bellow Hose
KF Stainless Steel Bellow Hose This KF or NW flange bellow hose is made out of 304-grade stainless steel which allows a high vacuum to be obtained with a large flow diameter for vapors. These bellow hoses are flexible and allow the user to connect a KF flanged vacuum pump to a KF flanged vacuum oven or any other application using adapters like our KF x NPT or KF x Tri-Clamp Fittings.
$97.22 - $243.05
-
KF Vacuum Flange Reducer Adapter
This 304 Stainless Steel KF Vacuum Flange Reducer / Adapter is designed to convert K16 to KF25 or KF25 to K40 and vise versa.
$52.78
-
KF-25 5 Way Manifold
This is a KF-25 5 Way manifold for the splitting of vacuum applications especially vacuum ovens connected to a single Vacuum Pump in an array. The material is 304 Stainless Steel with a 10^-7 torr @ 72F Vacuum Rating. (Note: Does not include KF-25 Clamp or O-ring these items are sold separately.)
$81.94
-
KF-25 90 Degree Stainless Steel Elbow
KF-25 90 Degree Stainless Steel Elbow This 90-degree elbow has KF-25 connections on the end and is made out of high polish 304-grade stainless steel.
$38.89
-
KF-25 Cross - 4 Way Splitting of Vacuum Applications
This is a KF-25 Cross for 4 Way splitting of Vacuum Applications especially vacuum ovens connected to a single Vacuum Pump in an array. The material is 304 Stainless Steel with a 10^-7 torr @ 72F Vacuum Rating. Does not include KF-25 Clamp or O-ring these items are sold separately.
$77.78
-
KF-25 Ground Joint PTFE Adapter
KF-25 Ground Joint PTFE Adapter This adapter will fit any standard 24/40 or 34/45 ground glass joints and adapt to a KF25 flange. This adapter is best used to hook up a glass system to a steel vacuum hose such a KF25 bellows. The Joint has an o-ring for better sealing, but vacuum grease is still recommended for the best connection.
$58.33
-
KF-25 Stainless Steel 90 Degree Manifold
KF-25 Stainless Steel 90 Degree Manifold This 90 degree stainless steel KF-25 manifold has 2 1/4" FNPT ports and measures 10" x 7".
$90.28 $41.67
-
KF-25 Stainless Steel 90 Degree Manifold - Long
KF-25 Stainless Steel 90 Degree Manifold - Long This 90 degree stainless steel KF-25 manifold has 2 1/4" FNPT ports and measures 10" x 36".
$111.11 $55.55
-
KF-25 Stainless Steel Ball Valve (Nitrogen Tested)
KF-25 (NW25) Stainless Steel Ball Valve This ball valve has a KF25 (NW25) High Vacuum Flange to adapt to any other KF25 pump or manifold if needed and is made out of 304 stainless steel with a PTFE seat and seals. BVV™ Tri Clamp Ball Valve - Data Sheet
$166.66
-
KF-25 Stainless Steel Spools
KF-25 Stainless Steel Spools This spool has KF-25 connections on the end and is made out of high polish 304-grade stainless steel.
$23.61 - $38.89
-
KF-25 Tee
This is a KF-25 Flanged Tee for High Vacuum Applications. The Material is 304SS and it has a maximum vacuum rating of 10^-7 torr @ 72F.
$62.50
-
KF-25 X 1" Stainless Steel Hose Barb
KF-25 X 1" Stainless Steel Hose Barb This is a KF-25 (NW25) x 1" Stainless Steel Hose Barb to adapter flexible vacuum tubing to the system made out of 304 stainless steel.
$48.61
-
KF-25 x Barb Adapter
KF-25 x Barb Adapter This 304 Stainless Steel KF-25 adapter is fitted with a 304 stainless hose barb adapter to connect a vacuum pump or vacuum oven to a flexible rubber hose.
$45.83 - $54.17
-
KF-25 x JIC Flare Adapter
KF-25 x JIC Flare Adapter This 304 Stainless Steel KF-25 adapter is fitted with a 304 stainless 37° JIC Flare adapter to connect a vacuum pump or vacuum oven to a stainless steel braided chemical hose or a hvac hose.
$55.55 - $69.44
-
KF-25 x KF-25 x 1/8" FNPT Adapter
KF-25 x KF-25 x 1/8" FNPT Adapter This 304 stainless steel KF-25 adapter is specifically designed for adapting Digivac Bullseye Precision Vacuum Gauges to systems with reducing and minimizing connect / leak points on the system.
$43.05
-
KF-25 Y Bellow
This Unique 304 Stainless Steel KF-25 Y Bellow has 3 attachment points for KF-25 fittings and 2 flexible ends and 1 rigid end that let the user position them the way that best suits their operation. It has an overall length of 17" and a width of ~16".
$291.66
-
KF-40 Stainless Steel Ball Valve (Nitrogen Tested)
KF-40 (NW40) Stainless Steel Ball Valve This ball valve has a KF40 (NW40) High Vacuum Flange to adapt to any other KF40 pump or manifold if needed and is made out of 304 stainless steel with a PTFE seat and seals. BVV™ Tri Clamp Ball Valve - Data Sheet
$166.66
-
KF-40 Stainless Steel FNPT End Cap
KF-40 Stainless Steel FNPT End Cap This is a FNPT KF-40 (NW40) Endcap to adapt a KF40 fitting to Female NPT Threads for 1/4", 3/8", and 1/2" NPT.
$47.22 - $54.17
-
KF-40 Tee
This is a KF-40 Flanged Tee for High Vacuum Applications. The Material is 304SS and it has a maximum vacuum rating of 10^-7 torr @ 72F.
$76.39
-
KF-50 Stainless Steel FNPT End Cap
KF-50 Stainless Steel FNPT End Cap This is a FNPT KF-50 (NW50) Endcap to adapt a KF50 fitting to Female NPT Threads for 1/4", 3/8", and 1/2" NPT.
$34.72 - $43.05
-
KF25 - 35/25 Spherical Ball Joint
Adapter from KF25 (NW25) to a 35mm ball joint fitting, commonly found on glass components. This part is recommended only to be used on glass joints with an o-ring seal.
$68.05 - $100.00
-
King Kone KING KONE CLOSER
KING KONE CLOSER Crown your pre-roll with a Dutch finish in just 4 easy steps. With this closer, you can produce up to 1,000 pre-rolls per hour from start to finish. Out of Stock: Due to high demand and the time required to craft this product, availability may take longer than our other items. At this time, we are not accepting pre-orders. We appreciate your patience as we work to fulfill all orders. Size: 109mm cone/King Size Cone Thank you for your understanding!
$2,777.73
-
King Kone King Kone Pre-Roll Machine V2
VERSION 2: KING KONE Pre-Roll Filling Machine Elevate your production with the King Kone pre-roll cone filling machine, the perfect choice for both businesses seeking to enhance efficiency and individuals aiming for professional-grade precision at home. This robust, metal-constructed model combines superior performance with affordability and ease of use. Designed for versatility, the King Kone accommodates a variety of pre-rolled cone sizes, ensuring it meets the demands of any operation. Its patented vertical bounce technology ensures optimal packing density and uniformity, offering the precision of hand-packing with the efficiency of automation. Capable of processing up to 169 cones per run, the King Kone is not just about quantity but also about quality. Adjustable settings allow you to control the packing density to match different product types and preferences, making it ideal for tailoring to specific needs. Whether you're looking to streamline your business's production process or perfect your personal pre-roll preparation, the King Kone provides a seamless, efficient, and precise packing experience, setting a new standard in pre-roll preparation. CAPACITY: Can fill up to 169 pre-rolled cones per run. COMES WITH: Attachments to fill 84mm, 98mm, and 109mm cones. POWER REQUIREMENT: 110 volt SIZE: 8 in x 9.5 in x 12 in King Kone How to:
$2,776.34
-
King Kone KING SHRED
KING SHRED King Shred offers the same mechanism as a hand grinder, but on steroids! King Shred is an American made grinder with one-of-a-kind strength source from it's 1/2 horse power motor that could deliver 50lbs of torque. All that info summed up means that your going to get the best of the best: a bad ass shredder expertly designed for consistent and fluffy grinding. King Shred's motorized hopper means no more babysitting the equipment. Say goodbye to dust, chunks, and clusters that make packing difficult. With easy maintenance and increased efficacy, this superior grinder is a must-have for any production.
$4,722.14
-
Koby Adapter for BVV Pumps Series
Koby Adapter for BVV Pumps Series This fitting allows the user to connect a 1/4" NPT fitting to the exhaust for the desired application such as a carbon exhaust filter. It is made of steel and comes with a Viton O-ring.
$38.89
-
Kuritech 3/4 ID PVC Reinforced Braided Hose
Kuritech 3/4 ID PVC Reinforced Braided Hose 3/4" Flexible hose that is ideal for heat transfer applications utilizing mixtures of water and propylene glycol. Specifications: Max Pressure: 150 PSI @ 20° Working Temperature: -4°C - 65°C
$23.61 - $444.44
-
L.J. Star L.J Star SSH Clamp Hardware
L.J Star SSH Series Clamp Hardware These are replacement bolts for L.J. Star SSH series High Pressure Clamps. It includes 1x Bolt, Brass Nut, and Lock Washer.
$40.28 - $79.17
You have seen 1008 out of 1655 products