BVV (Ok to Discount)
Neocision 20L Chiller (-40c) - ETL Rated
NEOCISION 20L Chiller (-40c) - ETL Rated Product Name Circulating Chiller Model NEO20L-40 Reservoir volume L) 20L Refrigeration performance No-load minimum temperature (℃) A: ﹣ 20℃ ( Customizable: ﹣ 30℃ / C: ﹣ 40℃ Best operating temperature (℃) A: ﹣ 20℃ ~ 20℃B: ﹣ 30℃ ~ 20℃C: ﹣ 40℃ ~ 20℃ Best operating environment (℃) ≤30 Environmental relative humidity (%RH) ≤65 Cooling capacity at -40 ℃ kw 0.7 Refrigerant R404A Electrical performance Cooling unit power (W) 1500 Sensor pt100 Controller, monitor liquid crystal Computer interface R485 optional safety protection Compressor delay protection, machine leakage,over-current, over-voltage protection Power AC230V±10%/60HZ Pump Power (W) 15 Maximum flow (L/min) 10 Maximum lift (m) 2.5 Liquid inlet and outlet pipe diameter (mm) φ18 Whole machinefunction Total Weight (Kg) 105 Tank opening/depth ( mm) φ300mm*300mm Out size (mm) 420*580*790 Adaptation rotary evaporator (volume* number) 10L*2 Note The equipment can be customized to different supply voltage frequency; different flow head external circulation system and external magnetic stirring device. TEMP: Displays the measured temperature value. To set the desired temperature, press the setting key until the TEMP SET value flashes. Press the setting key again to confirm the parameter. SET: Displays the desired temperature value set manually. RUN: Indicates that the chiller is operating. Cooling Indicator: Appears when the chiller is cooling. Circulation Indicator: Appears when the pump is operating. TIME: Displays the set running time; this value countdowns to zero and operation stops. To set a timer, press the setting key. When the TIME value flashes, enter the desired time using they arrow keys. Leave at zero if a timer is not needed. Silence Indicator: Appears when an alarm has been silenced. Alarm Indicator: It will appear when there is an alarm. Settings: Used for manually setting values and parameters. Left Arrow: Shifts to the numbers on the left to set desired value. Down Arrow: One push will decrease 1 digit; A long press will decrease digits faster. Up Arrow: One push will increase 1 digit; A long press will increase digits faster. Cooling Key: Press and hold key for more than 4 seconds to control start/stop the cooling function. Circulation Key: Press to start/stop the circulation function. Note: After all parameters have been input, press the cooling key for four seconds to being operation. Instructions Before Use The unit should be used under the following conditions: Place on a stable, non-combustible flat surface Ambient temperature of 5 ~ 35 ℃ Relative humidity ≤ 85% Atmospheric pressure: (86 ~ 106) KPa Altitude not higher than 2000 meters Power: 5L AC 110V±10%/60HZ, 20L: AC230V±10%/60HZ Keep away from any heat, corrosive gasses, strong vibration and electromagnetic sources. Provide a minimum of 300mm of space for proper ventilation (front and rear) Do not spill liquid anywhere other than the bath. When setting temperatures pay attention to freezing points (ethanol/ethylene glycol). When operating for the first time after replacing the heat transfer fluid there may be air trapped in the circulating pump, follow these instructions to purge: a. Disconnect the outlet line from the application NOTE: Fluid may leak from application, be ready with a bucket or plug the port. Hold the Outlet hose above the top of the bath so fluid does not drain out. b. Place the outlet hose into a clean collection bucket. c. Hold the outlet hose firmly so it does not fall out of the collection bucket d. Wearing safety glasses to shield any splashes, turn on the circulating function. e. After the liquid flow significantly increases, turn off the circulator. f. Reconnect the hoses to your application’s ports.
$6,929.12
Viton Replacement O-ring for TRS21 and BVV 2/4CYL Suction Valves
Viton Replacement O-rings for TRS21 and BVV 2/4CYL Suction Valves sold as single O-ring.
$2.86
Centrifuge Lid Replacement Gasket
Centrifuge Lid Replacement Gasket These lid replacement gaskets are cut to fit, they will not be fully connected once installed. The main purpose is to prevent splashing while operating, the gasket will not hold pressure.
$428.61 - $1,071.51
TRS21 Valve Head Complete Viton O-ring Kit
Replacement kit with Viton O-rings for the TRS21 head. Compatible for use with the Oil Extraction Market, Butane and Propane Extraction solvents.
$45.72
Safety Tools - The Extractor's Kit (AlCu)
The Extractor’s Safety Tool Kit These tools are forged out of 100% Aluminum Bronze (GB EX IIB). The material hardness is 20-30 HRC, which is still very durable for normal day to day work. They will not generate a spark when knocked against or dropped on steel parts. We have optimized the kit to only include what you will need on our equipment. This kit includes: -Combination Wrenches: 5/8” ¾” -Double End Wrenches: 19/17 mm 17/14 mm 14/10 mm -200mm Adjustable Wrench -250mm Adjustable Wrench -3/8” Drive Socket Wrench -Sockets: ½ 14mm 5/8 11/16 ¾ -Allen Keys: 3/16 ¼ -Phillips #2 Screwdriver-6mm Flathead Screwdriver-500g Cross-Peen Hammer
$857.21
12" x 12" Hemi Lid with Coil V2
12" x 12" Hemi Lid with Coil V2 This 12" Hemi Lid has a built in coil that can be used with a heated circulator to assist with internal temperature control during the recovery process. This hemi lid must be used with our 1200X12S and 1200FJS for proper fitment. PDF DRAWING
$678.62
Neoprene Gasket for Cubes
NEOPRENE GASKET FOR CUBES Replacement Neoprene gasket for acrylic vacuum chambers. The existing gasket will have to be completely removed in order to get the new one to seal. It is recommended to use a cleaning solution such as CitraKlean.
$55.72
Distribution Plate - 6"
Distribution Plate - 6" The 6" distribution plate is designed to be placed above a tube in shell heat exchanger to help evenly distribute liquid around the heat exchanger. It has a borosilicate sight glass to give you a visual of flow and dispersion into the heat exchanger.
$557.19
BVV 4 Cylinder Active Closed Loop Recovery Kit ITS/ETL to ANSI/ISA Certified
BVV 4 Cylinder Active Closed Loop Recovery Kit ITS/ETL to ANSI/ISA Certified (Pump comes with 1 yr. limited warranty) This is an Upgrade Kit which can be added to any one of our passive systems making it into an "Active" Closed Loop System. The Active Recovery Upgrade Kit will increase recovery times by condensing the vapor a lot faster than just a hot/cold differential. This will increase efficiency and productivity, many professionals use this method, as this drives profits. This Kit Includes the Following: BVV 4 Cylinder Butane Recovery Pump ITS/ETL to ANSI/ISA Certified BVV Large Condensing Coil 1/2" x 24" SS JIC Braided Hose (2) 1/2" x 48" SS JIC Braided Hose (2) 1/2" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV 5' HVAC Hose BVV Vacuum Tee RECOVER MORE WITH LESS BVV is proud to introduce our new and powerful line-up of Butane & Propane Recovery Pumps. Blending compact design with improved Gen III Pistons from RKMAC, this collection of pumps can help you recover 1lb. Butane / 0:51 Seconds! This pump Assembled in the USA and all the critical parts are domestically made. Finding parts wont be an issue with this pump. The piston seals are rated to 450F and the average operating temperature of the pump is 175F leading to a long service life. Certified by ITS/ETL to ANSI/ISA 12.12.01 for Use in Hazardous locations Class I & II, Division 2 and Class III, Divisions 1 & 2 environments. The computer controlled brushless DC motor operates at 3000 RMP nearly twice as fast as any other pump in its class. BVV Butane/Propane Recovery Pumps are: Process up to 10,000 lbs. of vapor recovery before rebuild Equipped with oil-less reciprocating compressors for a clean product Designed and Assembled in the U.S.A. with domestic and global parts Affordable and highly cost efficient Available in 2-Cylinder, 4-Cylinder, CMEP Retrofit Comes with a 1-year Manufacturer’s Warranty covering Hemp usage Rated universal voltage 100-240V AC 50/60 Hz 1Ph Built with high efficiency Brushless DC Motor used for variable speed control Equipped with Viton O-Ring Seals for Butane/Propane gas and oil compatibility Certified by ITS/ETL to ANSI/ISA 12.12.01 Noise level: 93.0 dB @ 1m *Butane recovery results were achieved on a collection base pressure greater than 30psi and using a recovery cylinder with a pressure <10psi. A dry ice coil was used in between the output port of the pump and the recovery cylinder to condense vapor.
$3,571.71
20L Receiving Flask
20L Receiving Flask Receiving flask for 20L rotary evaporators. 10L capacity. Connections: -40mm ID 60mm OD main connection flange -24/26 Ground Joints (2x) -15mm Barb on drain port NOTE: This model is an exact replacement for BVV Eco rotary evaporators manufactured before 2019
$328.60
Insulation Jackets for Centrifuges
Insulation Jackets for Centrifuges ***Disclaimer: Fiberglass may be present on the exterior of the jacket and users should use PPE when handling the jacket. These insulated jackets are specifically designed to fit BVV brand Centrifuges and allow the user to better control and keep a more stable temperature when running the system. The jackets are made out of flame retarded material and are insulated with fiberglass.
$642.91 - $1,642.99
KF-50 Stainless Steel FNPT End Cap
KF-50 Stainless Steel FNPT End Cap This is a FNPT KF-50 (NW50) Endcap to adapt a KF50 fitting to Female NPT Threads for 1/4", 3/8", and 1/2" NPT.
$42.86 - $50.00
2" Plastic Drum Faucet
Recommended for dispensing light oils, acids and cleaning solutions. FDA approved high-density polyethylene (HDPE) plastic faucet. The faucet is designed to fit 2" NPT threads and can be used to dispense most non-flammable liquids. Use with plastic and steel drums. Tough polyethylene. FDA compliant. Material: High density polyethylene (HDPE ) is the most commonly used resin. This economical plastic has good impact resistant, is naturally translucent, flexible, and typically used for personal care products, such as shampoo bottles. Adding color will give HDPE an opaque look that will result in an increase in weight and rigidness. We have a variety of these rigid and tough high density polyethylene products in stock, from containers, pails, bottles, caps, tubs, and jugs. HDPE works well in below freezing temperatures. HDPE heat compatibility varies. Generally, it should not be used with products filled at over 145°F.
$35.72
50L Solvent Pro Rotary Evaporator Auxiliary Condenser
50L Solvent Pro Rotary Evaporator Auxiliary Condenser Replacement Auxiliary Condenser for 50L Solvent Pro Rotary Evaporator
$428.61
5L Solvent Pro Rotary Evaporator Main Condenser
5L Solvent Pro Rotary Evaporator Main Condenser 5L Solvent Pro Rotary Evaporator Main Condenser *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$428.61
KPR Fitting Port Reducer
KPR Fitting Port Reducer The KPR Fitting Port Reducer is made out of 316 stainless steel and reduces the port from 1/2"FJIC to a 1/4" MJIC. The connection type is a 37° JIC with a 7/16-20 UNF rated thread. BVV™ KPR Fitting Port Reducer - Data Sheet
$25.72
Solvent Pro Series 60/80 Clamp
Solvent Pro Series 60/80 Clamp This is a replacement clamp for 10, 30, and 50L Solvent Pro Rotary Evaporators. This clamp fits an 60mm(2.36") Inner Diameter and 80mm(3.15") Outer Diameter joint.
$21.43
Solvent Pro Series 18/35 Clamp
Solvent Pro Series 18/35 Clamp This is a replacement clamp for 5, 10, 30, and 50L Solvent Pro Rotary Evaporators. This clamp fits an 18mm(0.71") Inner Diameter and 35mm(1.38") Outer Diameter joint.
$21.43
3 Gallon WIDE Stainless Steel SIDEMOUNT - POT ONLY
3 Gallon WIDE Stainless Steel SIDEMOUNT - POT ONLY ***Note: 'with Hardware' Option only includes the side-mount manifold with gauge pre-installed. (Does Not Include Lid or Gasket) This is a replacement part for the following Vacuum Chambers: Best Value Vacs 3 Gallon Wide Stainless Steel Side Mount Vacuum and Degassing Chamber Glass Vac 3 Gallon Aluminum Vacuum Chamber Dimensions: 9" Tall x 10.75" Diameter Hole Size: 21/64 Material: 304 Stainless Steel
$61.43 - $85.72
Harvest Right Vacuum Pump Activated Carbon Exhaust Filter
Carbon Exhaust Filter for Harvest Right Vacuum Pump Replaces Koby Junior (US Patent# 3169112A) BVV Vacuum Pump Activated Carbon Filter for use with Harvest Right Vacuum pumps. Pump Models Include: OP-VLU11060-PREM This filter will adsorb contaminants such as oil aerosols, oil vapors, certain other hydrocarbon vapors, and trace moisture. They also trap all foreign solid particles and bacteria down to 0.5 microns in size. Key Features: Purifies Exhaust Gases from Vacuum Pumps Up to 19 CFM 0.5 Micron Filtration levels. Helps Maintain Safe Working Environment Adsorbs Organic Vapors and Small Particles High-Efficiency Filtration Minimal Pressure Drop Maintenance Free - Completely Disposable Pressure Safe to 90 PSI M30 x 1.0 - Brass Pump Connection Filter connections 1/4" NPT Pipe Fitting Connections Removes the following contaminants: Oil Mist Oil Aerosols Oil Vapors Hydrocarbon Vapors Moisture Droplets Dust Pipe Scale Rust Fine Particles Odors Organic Aerosols Other Foreign Matter Lifespan:720 hrs. of continuous operation. (Then replacement is recommended) **NOTE PUMP NOT INCLUDED
$164.30
Purple BVV Vacuum Pump Activated Carbon Exhaust Filter
Carbon Exhaust Filter for BVV Vacuum Pumps Replaces Koby Junior (US Patent# 3169112A) BVV Vacuum Pump Activated Carbon Filter for use with Purple BVV vacuum pumps. Pump Models Include: BVV4D, BVVSF6S, BVVSF6D, BVV7S, BVV9D, BVVSF12D This filter will adsorb contaminants such as oil aerosols, oil vapors, certain other hydrocarbon vapors, and trace moisture. They also trap all foreign solid particles and bacteria down to 0.5 microns in size. Key Features: Purifies Exhaust Gases from Vacuum Pumps Up to 19 CFM 0.5 Micron Filtration levels. Helps Maintain Safe Working Environment Adsorbs Organic Vapors and Small Particles High-Efficiency Filtration Minimal Pressure Drop Maintenance Free - Completely Disposable Pressure Safe to 90 PSI M30 x 1.0 - Brass Pump Connection Filter connections 1/4" NPT Pipe Fitting Connections Removes the following contaminants: Oil Mist Oil Aerosols Oil Vapors Hydrocarbon Vapors Moisture Droplets Dust Pipe Scale Rust Fine Particles Odors Organic Aerosols Other Foreign Matter Lifespan:720 hrs. of continuous operation. (Then replacement is recommended) **NOTE PUMP NOT INCLUDED
$164.30
Jacketed Sucker Pot
Jacketed Sucker Pot This jacketed sucker pot works perfectly as a collection base for extracted oil and easy discharge or as a storage vessel for distillate dispensing. Both of these applications are made easier with the use of a heater running through the jacket. This pot can be mounted to an extraction rack with the use of 8" pipe hangers. Connections: Top: 6" Tri-Clamp Bottom: 1/4" FNPT Jacket: 1/4" FNPT (2x ports)
$500.04
4" Wiped Film Evaporator (WFE) Distillation Turn Key System - USA MADE
4" BVV Wiped Film Evaporator This system has a 1-2 week lead time. The BVV™ 4" Wiped Film Evaporator (WFE) is a full turnkey distillation kit that will will allow anyone to run a molecular distillation. With the magnetically driven wiper and high vacuum seals this system is able to achieve vacuum levels below 10 mtorr. The system has multiple temperature control apparatuses that allow the user to dial in specific settings that works best for their application. The maximum operating temperature of the outer jacket is 200°C with the standard circulators shown below. The maximum feed rate is up to 7LPH. On average, you can expect to flow 500-1000ml per hour. All heated circulators can be tailored to your specific needs, just ask our team of experienced account representatives! The temperature controlled circulators will need thermal fluid that corresponds with the temperatures needed. Click here to browse fluids. *Heating and Chilling Fluids are not included* Duratherm S - 7 Gallons - Bottom heater (wiper body) Therminol XP Heat Transfer Fluid - 5 Gallons - Top and middle heater *Propylene Glycol - 5 Gallons - Fluid for the diffusion pump option chiller. Ethanol 99% or Isopropyl 99% - 2 Gallons - Cold Trap / Cold Finger. For a full list of ancillary equipment included in the kits please see the table below: KIT Part of System Component Electrical Requirements (V / Ph / A) WFE04-TK-01 Standard Model Wiper Assembly BVV™ Stirring motor 120V / 1Φ Vacuum System BVV™ Pro Series 35.3CFM Rotary Vane Vacuum Pump* DigiVac Bullseye Precision Vacuum Gauge 220V / 3Φ AA Batteries (4x) Temperature Controlled Circulators Polyscience 7L Polyscience 15L (2x) 120V / 1Φ / 10A 220V / 1Φ / 10A Injection Beaker and Wrench 7LPH Peristaltic Heated Hose 120V / 1Φ 120V / 1Φ WFE04-TK-02 Upgraded Vacuum System Upgraded Cold Trap Wiper Assembly BVV™ Stirring motor 120V / 1Φ Vacuum System BVV™ Pro Series 35.3CFM Rotary Vane Vacuum Pump* Summit Research Diffusion Pump (SR-DP04A)** DigiVac Bullseye Precision Vacuum Gauge 220V / 3Φ 180/264V / 1Φ / 10.5A AA Batteries (4x) Temperature Controlled Circulators Polyscience 7L Polyscience 15L (2x) 120V / 1Φ / 10A 220V / 1Φ / 10A Injection Beaker and Wrench 7LPH Peristaltic Heated Hose 120V / 1Φ 120V / 1Φ Cold Trap Polyscience IP100 120V / 1Φ / 11.5A WFE04-TK-03 Upgraded Vacuum System Upgraded Cold Trap Outlet Pumps Wiper Assembly BVV™ Stirring motor 120V / 1Φ Vacuum System BVV™ Pro Series 35.3CFM Rotary Vane Vacuum Pump* Summit Research Diffusion Pump (SR-DP04A)** DigiVac Bullseye Precision Vacuum Gauge 220V / 3Φ 180/264V / 1Φ / 10.5A AA Batteries (4x) Temperature Controlled Circulators Polyscience 7L Polyscience 15L (2x) 120V / 1Φ / 10A 220V / 1Φ / 10A Injection Beaker and Wrench 7LPH Peristaltic Heated Hose 120V / 1Φ 120V / 1Φ Cold Trap Polyscience IP100 120V / 1Φ / 11.5A Outlet Pumps Beaker and Wrench Gear Pump (2x) Beaker and Wrench Heat Pad PID Controller 120V / 1Φ 120V / 1Φ Notes: *The Rotary vane vacuum pump paired with this kit uses 3Φ power, a smaller single phase pump can be substituted if needed. Substitution will have an impact the performance versus the standard unit. **The Summit Research diffusion pump must be water cooled, if facility water cooling is not an option an additional chiller may be needed, a Polyscience 1HP Durachill is recommended. An air cooled diffusion pump can be provided as a substitute. Substitution will have an impact the performance versus the standard unit.
$64,290.76 - $108,579.95
Replacement PID 3.2TS and 7.5TS
Replacement PID 3.2TS and 7.5TS Specifications SKU FCT30L0-E-F Temperature Range: 32°F - 212°F Dims/weight 4.5 x 4.5 x 4 / 1lb Timer Range 0 -999 Built in Calibration: Yes Temp Display Mode For C Compatible Ovens 32TSO - 32TSB- 75TSO - 75TSB Temperature Accuracy +/- 1°F
$371.46
16CF BVV™ Neocision ETL Lab Certified Vacuum Oven
16CF BVV™ Neocision Certified Lab Vacuum Oven, 5 Individually Heated Shelves, LED's - 3 Year Warranty Disclaimer: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in well-ventilated areas! Introduction Our vacuum ovens are purpose-built to perform degassing / purging of light hydrocarbon solvents. Using the technique of cold boiling, the oven applies a gentle heat under reduced pressure conditions to expedite solvent degassing while simultaneously preserving color, aroma, and overall solute quality. We've applied our extensive vacuum expertise and industry experience to produce a series of ovens designed exactly for your needs: low consumption, high-throughput, and reliable operation. Performance Capabilities At Best Value Vacs, we make every effort to provide oven performance capabilities in a standardized format. We're not interested in juking our stats to make a sale. Instead, our goal is to provide quality, transparent production capabilities that meet the demands of our professional customers. Temperature Stability: ±1.0° Temperature Uniformity: within 4% of the temperature setpoint. Heat-Up Time: 30 minutes. Ultimate Vacuum: <500 µmHg / mTorr / micron. Time to Vacuum: 10 minutes to 29"Hg using our 12CFM Spark Free Vacuum Pump Vacuum Hold: guaranteed to lose less than 1"Hg (25.4 torr) in 24 hours. Technical Data Electrical Voltage 120V Frequency 60Hz Power 2000W Current 20A Plug NEMA 5-15 Internal Chamber Heating Individual direct-heat shelves Chamber Material Stainless Steel Dimensions (LxWxH) 25.5" x 32" x 34" Vacuum Gauge Style Glycerin-filled for accuracy and longevity Range (units) -30 to 0 (inHg) / -1 to 0 (bar) Shelving Ships With 8 Shelves Shelf Dimensions (LxW) 24.75" x 31.5" Shelf Capacity 780 in^2 Total Shelf Capacity 6240 in^2 Safety Seal Silicone on Tempered Glass Window Dimensions (LxH) 29.25" x 32" Lights 4 strips of LEDs provide a clear, bright view of the interior Handle No plastic, all metal parts for lifetime durability Exterior Dimensions (LxWxH) 37.25" x 45" x 46" Weight 500lbs Support Locking Casters Safety Electrical Built-in, resettable, overcurrent circuit breaker Thermal Automatic overtemperature shutoff Compliance CE CE Listing Recognized ISO ISO 9001:2015 ETL Certified Conforms to ANSI/UL STD.61010-1, 61010-2-010 -- Certified to CAN/CSA STD. C22.2 NO.61010-1, 61010-2-010 Connections Vacuum Inlet KF25 / NW25, quarter-turn valve Purge Inlet 5/16" Barbed, 10-turn valve Atmospheric Release Quick-release dial Contains Ships With KF25 x 1/4" JIC Flare with 1/4" vacuum hose User Manual Included Vacuum Pump Sold Separately. Warranty 3 Years Capacity and Throughput Planning Oven capacity requirements vary widely by the producer. We wanted to create a method to assist in determining the best oven match for your operation, based on a few of the parameters of your extraction and of your desired purge. We based this formula on an expected extraction yield of 25%, with an extract-density of 1 g/in2. Using the following variables, this formula is designed to provide an estimate of your required shelving capacity: Size = Extraction Batch Size (lbs) Number = Runs per 24h Period Purge = Your desired purging duration (hours) Area Required (ft2) = [(Size) * (Number) * (Purge+1)] / 122 Area Required (in2) = (Size) * (Number) * (Purge+1) * 1.18 Note: This item is a freight ship item and will ship Via UPS Ground Freight. Expedited freight can only be calculated by calling customer service 331-281-0154. All orders with expedited freight through the website will not be honored and will need to be re-quoted. A valid Phone Number IS REQUIRED to ship, Otherwise UPS freight Cannot Contact you for a delivery setup window. Freight Time is 2-5 Days. West Coast 5 Days, Midwest 2 days, East Coast 3-4 days.
$19,644.40
CPS TRS21 Top Dead Center Piston Depth Calibration Plate
CPS TRS21 Top Dead Center Calibration Plate & Bolts Use with the Top Dead Center Clearance (TDCC) instructions Use this plate and a depth gauge to measure the Top Dead Center Clearance of the piston/cylinder/head assembly. Shims that come with the piston cylinders are stacked to create an area of displacement between the top of the cylinder and the compressor head. BVV's Recommended depth is between 0.008" and 0.012" for the CPS TRS21 for optimum performance. Top Dead Center Clearance Instructions *Depth Gauge Not included, its only used for reference in the photo. Any type of simple digital depth gauge will work to check the piston displacement.
$42.86
BVV 5.75" Glass Chamber Lid
BVV 5.75" Glass Chamber Lid This tempered soda lime glass lid is available with or without holes. Both feature 5.75" outer diameter and a thickness off 12mm or .472".
$35.72 - $50.00
BVV Vacuum Jacket Assembly
This vacuum jacket assembly is pre-assembled to fit on BVV Jacketed Stainless Steel tanks to allow users to create a vacuum jacket around the tank increasing the insulation of the stainless steel LP tank. This assembly comes with pre-taped 1/2" MNPT fitting on the main assembly with a compound gauge and 1/4" 37 JIC flare and BVV butterfly valve. It also comes with a 1/2" MNPT plug for the other port on the tank.
$97.15
Spark Free Safety Tools- 200mm Adjustable Wrench
200mm Adjustable Wrench This adjustable crescent wrench is made of aluminum bronze, a material that will not spark when accidentally knocked against steel and stainless steel materials. This will limit the sources of possible ignition within a solvent rich environment. The jaws on this wrench will fit on a nut or bolt up to 31/32" or 24mm.
$35.72
Half Ton - High Purity USA ISO-BUTANE - 99.5% Guaranteed
Half Ton - High Purity USA ISO-BUTANE - 99.5% Guaranteed DISCLAIMER(S): This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in WELL VENTILATED AREAS! Notice: This item will ship via Freight ONLY. This tank requires a CGA 510 fitting - Sold Separately BVV™ always recommends distillation of every solvent before use. *Actual liquid weight is 490LB California now prohibits the retail sale of any Non-Odorized butane in quantities larger than 150ml. If you are not a retail purchaser you can call in to place an order. Permitted Sales Include the Following: Medical Collectives or Cooperatives operating under CA Health & Safety Code Section 11362.775 Persons licensed to perform volatile solvent extraction activity under CA Bus & Prof Code Division 10 Manufacturers, wholesalers, resellers, or retailers solely for the purpose of resale At BVV™, quality is everything, and our ISO-Butane is certainly no exception. This ISO-Butane is sourced here in the U.S, so you know it’s going to be of high purity: we guarantee 99.5% purity. With such high quality, you’ll see the results. By cutting down on mystery oils and other contaminants, our instrument-grade solvent will make for a higher quality extract. This solvent is clean, odorless, and colorless, meaning there are zero hydrogen sulfide-based Ethyl Mercaptan odorants. It’ll arrive in a DOT refillable LP tank, equipped with liquid withdrawal valve (Diptube). Made to keep you going for a long time. Typical Analysis: ISO-Butane >99.8% Methane <1 ppm Ethane <1ppm N-Butane <2000 ppm Propane <250ppm Isopentane <2 ppm Water <3 ppm Oxygen <5 ppm Nitrogen <10 ppm Sulfur Non-Detected **Notes: Actual ISO-butane liquid weight is 490LB BVV™ always advises distillation of every solvent before using it. DISCLAIMER: Our items are intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. For safe operation, only use the unit in well-ventilated areas. ***Shipping Notes: This item will ONLY ship via UPS Ground, in accordance with FAA regulations. Any orders including solvent will NOT be shipped Expedited. If an order includes solvent as well as additional items, it will all be shipped via UPS Ground/Freight even if you’ve selected Expedited. If you want the non-solvent item to ship Expedited, place 2 separate orders; we won’t split up orders and ship them separately otherwise. We do not ship solvents to Hawaii, Puerto Rico, or any other U.S. Territory outside of the contiguous 48 States. Shipping solvent to Alaska will ONLY be via freight and will be required to travel through Canada. Our shipping policies are in place to ensure safe transport of solvents and prevent any problems with shipping times for Best Value Vacs customers
$4,214.62
Table Top Cart Filler XL 6 Liter
Table Top Cart Filler XL 6 Liter Fill 6000 1ml Carts per Load This 6 Liter capacity Giant is made to fill. Fully jacketed 304SS with a design that allows the OIL inside to fully drain creating little to no loss. The system is made of all parts that can be sterilized. The body, valves and all connections are 304 Stainless Steel and the hosing is PTFE. The body of the vessel is fully jacked and is recommended to be run with stand alone heater to pre-heat the oil. The hose is heated and insulated. The hose temperature is controlled by an Digital PID. The hose and PID controller are precision made in the USA. The hose uses Platinum Thermocouples for durability and accuracy, which means you wont run into down time or temperature errors. To use the system you will need Nitrogen to back pressure the oil in the tank. The pressure is regulated by a low pressure regulator. To dispense the end of the hose has a toggle valve that connects to a Lure Lock connection. System Specs. Nitrogen Input MAX Pressure: 150PSI Regulator working pressure: 0.5-30PSI (*recommended pressure 10PSI) Hose Temperature Rating: 50°F - 450°F Digital* Controller Temperature Range: 50°F -450° Includes Right Angle Attachment for added user flexibility. Non-Metered Dispensing with toggle valve control. Pressure gauge for pressure monitoring: 0-150PSI Cleaning: NOTE: Please Clean Prior to first use the system does not come sterilized. A simple IPA wash down will be sufficient. At any point the system can be cleaned using IPA or D-limonene. *The controller has been updated to a Digital PID controller to replace the photographed analog style rotary dial.
$3,428.84
Eco Oven Power/LED Switch
Green Eco oven power switch.
$21.43
1.5 Gallon Tall Stainless Steel COLD TRAP - POT ONLY
1.5 Gallon Tall Stainless Steel COLD TRAP - POT ONLY ***Note: Hardware Only Includes the Flares with Bulk Heads preinstalled. (Does not Include Lids or Gaskets) This is a replacement part for the following Vacuum Chambers: 1.5 Gallon (2QT Tank) Dry Ice, Liquid Nitrogen Cold Trap Dimensions: 8-5/8"" Tall x 7-1/8"" Diameter Material: 304 - 2B Stainless Steel
$82.86 - $100.01
10L & 20L Bump Trap
10L & 20L Bump Trap *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$342.88
2LB TFX Closed Loop Extractor
2LB TFX Closed Loop Extractor Are you ready to embark on an exciting journey into the world of extraction? Look no further than the TFX, your perfect entry point into the world of closed-loop extraction. The TFX offers exceptional performance right out of the box at an affordable price, making it an excellent choice for both beginners and experienced extractors. But that's not all – the TFX also serves as a versatile foundation for future upgrades and enhancements, allowing you to level up your extraction game over time. Whether you're just starting or aiming to expand your capabilities, the TFX provides a solid base that can be customized to meet your evolving needs. With its adaptable design and compatibility with various upgrades, the TFX empowers you to experiment with new processing techniques and adapt to changing industry demands. Begin your journey with the TFX and open the door to endless possibilities for innovation and growth in the extraction realm. Introducing the TFX closed-loop extractor, the next step in the evolution of the popular Apollo extractor. The TFX brings a new era of safety, user-friendliness, and performance to the table. Building on the success of its predecessor, the TFX takes operator safety to the next level with enhanced safety mechanisms, including High-pressure Clamps and pressure relief valves as standard features. Extract harvesting is made easier with splatter platter bases, ensuring a cleaner and smoother process. The TFX's optimized design translates to improved ease of use, safety, and performance, resulting in top-quality extracts. The TFX is the cornerstone of many extractors' journeys, offering a reliable, efficient, and future-ready solution to meet your evolving needs. The TFX closed-loop extractor comes in three model variants, catering to different extraction requirements. The V1 Explorer is the choice for budget-conscious individuals looking to enter the world of extraction affordably. With features like a DOT-Approved carbon steel recovery tank, 1/4" JIC Recovery lines, and polycarbonate sight glasses, it lays the foundation for easy future upgrades. For those seeking a professional setup from the start, the V2 Professional model is the ideal option. It comes with an upgraded stainless steel recovery tank featuring 1/2" JIC Recovery lines for optimized solvent recovery. Enhanced borosilicate sight glasses provide better visibility during the extraction process. If you're aiming for the ultimate extraction experience, the V3 Elite model is the answer. This model includes all the upgrades of the professional variant, along with additional features like a solvent dispersal plate for uniform biomass saturation and a jacketed splatter platter for use with a heated circulator, improving solvent recovery efficiency. The TFX closed-loop extractor lets you choose the perfect model for your budget and needs. Whether you're starting small or aiming for professional-grade capabilities, the TFX series provides the perfect foundation for your extraction journey. No matter which model you choose – Explorer, Professional, or Elite – the TFX closed-loop extractor offers limitless modification possibilities to enhance your capabilities and stay ahead of industry trends. Optimized for quick wash extraction procedures, the TFX ensures exceptional purity and yield. If you prefer soaking procedures, simply add our 316L SS Tri-Clamp Ball Valve below the material column to adapt the TFX. For the utmost purity, pair your TFX with an Inline CRC (Color Remediation Column) for the highest quality and purest extracts. Running fresh frozen material? Swap the standard 4"x 24" spool with a Sleeved Spool to preserve your biomass's flavor during extraction. To achieve ultimate clarity, reduce wax content by incorporating an injection coil into your setup. To enhance solvent recovery and reduce loss, consider our BVV 2 Cylinder Active Closed Loop Recovery kit for your TFX closed-loop extractor. This kit boosts solvent recovery efficiency, saving you time and resources. With the TFX closed-loop extractor and its range of modification options, you have the freedom to customize your extraction setup to match your unique needs. Stay at the forefront of the industry and unlock your extraction process's full potential with the versatile TFX closed-loop extractor. As a premier extraction equipment manufacturer, we prioritize precision and safety in the extraction process. The TFX is designed with these principles in mind, offering a cutting-edge solution for extraction professionals. Constructed from high-quality stainless steel, the TFX ensures exceptional durability and resistance to corrosion, providing you with a reliable and long-lasting extraction solution. Its innovative design incorporates advanced safety features, including high-pressure clamps, pressure relief valves, and sight glasses, ensuring operator well-being and operational control. Its superior design promotes efficient solvent flow and comprehensive material saturation, resulting in high-quality, potent extracts that meet your precise requirements. When it comes to introductory closed-loop extractors, the TFX sets a new standard with its exceptional performance, safety features, and reliability. With our product, you can streamline extraction operations, boost productivity, and produce premium extracts that surpass industry standards. At BVV, we take pride in offering top-tier extraction equipment tailored to your unique needs. Our team of experts is dedicated to providing unmatched customer support, assisting your extraction journey and take your business to new heights. Specifications 4"x24" 1LB Material Column 12"x12" Collection Base Body 12" Collection Base Splatter Platter 100um Nitrile BUNA-N Mesh Gaskets 1.5" Polycarbonate or Borosilicate Sight Glasses 125 PSI ASME Safety Valves -30hg-250PSI Compound Pressure Gauge 1/4" or 1/2" Full Bore Recovery Lines 1/4" JIC process Flow lines Explorer Professional Elite DOT Carbon Steel Solvent Tank Polycarbonate Sight Glasses 1/4" JIC Recovery Lines Stainless Steel Solvent Tank Borosilicate Sight Glasses 1/2" JIC Recovery Lines Stainless Steel Solvent Tank Borosilicate Sight Glasses 1/2" JIC Recovery Lines Solvent Dispersal Plate Jacketed Splatter Platter ***Note: Solvent not included with systems unless ordered separately. Any order with butane WILL NOT SHIP EXPEDITED.*** ***DISCLAIMER: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in extremely well-ventilated areas. Check with your local fire marshal for guidance when operating indoors. *Note: Column capacity may vary depending on the density of packed material and packing density. Capacity is calculated using the industry standard of 4.2g/in3. This is the upper limit for column capacity. Low density, uncut, and/or lightly packed material can reduce capacity by 50%. For best results, we recommend to tightly pack coarse ground material.
$1,821.57 - $2,643.06
1LB TFX Closed Loop Extractor
1LB TFX Closed Loop Extractor Are you ready to embark on your extraction journey? Look no further than the TFX, the perfect introductory closed-loop extractor to kickstart your extraction journey. Not only does the TFX deliver exceptional performance at an affordable price right out of the box, but it also serves as an excellent base unit for future upgrades and modifications as level up your extraction game. Whether you're just starting or looking to expand your capabilities, the TFX provides a solid foundation that allows you to tailor your extraction setup to meet your evolving needs. With its versatile design and compatibility with various extractor upgrades, the TFX empowers you to explore new processing techniques and adapt to changing industry demands. Begin your extraction journey with the TFX, and unlock limitless possibilities for innovation and growth in the world of extraction. The TFX closed loop extractor represents the evolution of the highly popular Apollo closed loop extractor, introducing a new era of enhanced safety, ease of use, and performance. Building upon the success of its predecessor, the TFX provides greater safety, ease of use, and performance. Designed with operator safety in mind, the TFX incorporates improved safety mechanisms, including High-pressure Clamps and pressure relief valves standard to ensure maximum safety during the extraction process. Furthermore, the TFX line of closed-loop extractors makes extract harvesting a breeze with splatter platter bases standard. Its optimized design results in superior ease of use, performance, and safety yielding exceptional quality extracts. The TFX closed-loop extractor represents the foundation of most extractors' journey, providing would-be professionals and established professionals alike with a reliable, efficient, and future-proof solution to meet their evolving needs. The TFX line of closed-loop extractors is available in three distinct model variants to suit various extraction needs. The V1 Explorer is the ideal choice for budget-conscious individuals seeking an affordable entry-level option to venture into the world of extraction. This model features a DOT-Approved carbon steel recovery tank, 1/4" JIC Recovery lines, and polycarbonate sight glasses, providing a solid foundation that can be easily upgraded to professional or elite options in the future. For those aiming for a professional setup from the start, the V2 Professional model is the way to go. It includes an upgraded stainless steel recovery tank with 1/2" JIC Recovery lines, ensuring optimized solvent recovery. Additionally, the professional model includes upgraded borosilicate sight glasses, enhancing the visibility of the extraction process. If you're seeking the ultimate extraction experience, the V3 Elite model is your go-to solution. It incorporates all the upgrades of the professional model, including the upgraded stainless steel recovery tank with 1/2" JIC Recovery lines and upgraded borosilicate sight glasses. Moreover, the elite model goes beyond by featuring a solvent dispersal plate for even biomass saturation and a jacketed splatter platter for use with a heated circulator to ditch the hot water bath and further optimize solvent recovery. The TFX closed-loop extractor empowers you to choose the perfect model that suits your budget and requirements, Whether you're starting out or aiming for professional-grade capabilities the TFX Closed Loop Extractor series is the perfect foundation to start your extraction journey. Whether you opt for the Explorer, Professional, or Elite model, the TFX line of closed-loop extractors offers infinite modification possibilities to expand your capabilities and stay ahead of the evolving needs of the industry. While the TFX is specifically optimized for quick wash extraction procedures, ensuring exceptional purity and yield. It can easily be adapted for soaking procedures by adding our 316L SS Tri-Clamp Ball Valve below the material column. For those seeking absolute purity, pairing your TFX with an Inline CRC (Color Remediation Column) allows you to create the highest quality and purest extracts imaginable. If running fresh frozen material is your goal, simply swap out the standard 3"x 24" spool with a Sleeved Spool to chill your material during the extraction process and preserve the flavor of your starting biomass. To achieve absolute clarity in your extracts, reduce wax content by incorporating an injection coil into your setup. If you're looking to reduce solvent loss and improve recovery times, consider adding our BVV 2 Cylinder Active Closed Loop Recovery kit to your TFX closed loop extractor. This kit enhances solvent recovery efficiency, ultimately saving you time and resources. With the TFX closed loop extractor and its extensive range of modification options, you have the freedom to customize your extraction setup to meet your unique requirements. Stay at the forefront of the industry and unlock the full potential of your extraction process with the versatile TFX closed-loop extractor. As a leading manufacturer of extraction equipment, we understand the importance of precision and safety in the extraction process. The TFX is engineered with these principles in mind, offering a cutting-edge solution for extraction professionals. Crafted from high-quality stainless steel, the TFX boasts exceptional durability and corrosion resistance, providing you with a reliable and long-lasting extraction solution. Its innovative design incorporates advanced safety features, including high-pressure clamps, pressure relief valves, and sight glasses, to ensure operator well-being and operational control. Its superior design promotes efficient solvent flow and thorough material saturation, resulting in high-quality, potent extracts that meet your exact specifications. When it comes to introductory closed-loop extractors, the TFX stands out for its exceptional performance, safety, and reliability. With our product, you can streamline your extraction operations, increase productivity, and produce premium extracts that exceed industry standards. At BVV, we take pride in delivering top-notch extraction equipment that caters to your specific needs. Our team of experts is committed to providing unparalleled customer support, assisting you every step of the way, from purchase to setup and beyond. Elevate your butane extraction game with the TFX, the ultimate top-fill closed-loop extractor. Contact us today to start your extraction journey and take your business to new heights. Specifications 3"x24" 1LB Material Column 6"x12" Collection Base Body 6" Collection Base Splatter Platter 100um Nitrile BUNA-N Mesh Gaskets 1.5" Polycarbonate or Borosilicate Sight Glasses 125 PSI ASME Safety Valves -30hg-250PSI Compound Pressure Gauge 1/4" or 1/2" Full Bore Recovery Lines 1/4" JIC process Flow lines Explorer Professional Elite DOT Carbon Steel Solvent Tank Polycarbonate Sight Glasses 1/4" JIC Recovery Lines Stainless Steel Solvent Tank Borosilicate Sight Glasses 1/2" JIC Recovery Lines Stainless Steel Solvent Tank Borosilicate Sight Glasses 1/2" JIC Recovery Lines Solvent Dispersal Plate Jacketed Splatter Platter ***Note: Solvent not included with systems unless ordered separately. Any order with butane WILL NOT SHIP EXPEDITED.*** ***DISCLAIMER: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in extremely well-ventilated areas. Check with your local fire marshal for guidance when operating indoors. *Note: Column capacity may vary depending on the density of packed material and packing density. Capacity is calculated using the industry standard of 4.2g/in3. This is the upper limit for column capacity. Low density, uncut, and/or lightly packed material can reduce capacity by 50%. For best results, we recommend to tightly pack coarse ground material.
$1,214.38 - $1,928.72
10L Solvent Pro Rotary Evaporator Evaporating Flask
Replacement Evaporating flask for 10L solvent pro rotary evaporators.
$205.73
1LB EVO Closed Loop Extraction Kit
1LB Evo Closed Loop Extraction Kit (System comes with 1 yr. limited warranty) The EVO series of 1LB closed-loop extractors was designed with the evolution of stand-up extractors in mind. The aim of the EVO series of extractors is to provide unparalleled utility and ease of use within a traditional stand-up design. The EVO series was designed to tackle the two most common plights with stand-up extractors, difficulty in extract harvesting, and integration of adsorbent filtration. The Evo series accomplishes both through the use of its elevated extract pour spout and its optional inline color remediation column. Beyond the elevated pour spout and optional inline color remediation column. The EVO series aims to provide unbridled safety and solvent recovery speed through the integration of ASME pressure relief valves on both the material column and collection base standard and full bore 1/2" recovery lines found on the professional, elite, and active explorer models. The 1lb EVO Closed Loop Extraction kit comes complete with a top fill injection manifold including a compound gauge, a 125 psi ASME pressure relief valve, and two full bore ball valves complete with 2x 1/4" Male JIC connections on the explorer and both 1/4" & 1/2" Male JIC connections on the professional and elite models. Just below the injection manifold, all 1lb EVO models have a solvent dispersion plate that evenly disperses solvent into the 3"x 24" 1lb material column which is enclosed by 2x 100 micron Buna-N mesh gaskets. Both the Professional and Elite models come complete with an inline 3" x 6" color remediation column just below the material column with a 300-gram media capacity and a filter stack utilizing both a 5 micron & 1 micron sintered disk. Professional and Elite models also include 25-micron filter paper and a 500-gram sample of Pure-Flo B80 Below the 1lb material column and optional inline color remediation column the 1lb Evo includes the jacketed and elevated pour spout collection base that allows for easy extract harvesting and speedy solvent recovery. The elevated base can accommodate up to a 5:1 solvent to biomass ratio and accept a standard round pyrex dish or a small parchment paper boat below the pour spout. Upon completion of the run, extract removal is made easy by simply draining the extract from the elevated extract pour spout. Both the professional, elite, and active explorer models have increased solvent recovery capability from the jacketed collection base through full bore 1/2" recovery MJIC connections and stainless steel recover hoses. Beyond the larger recovery lines and inline color remediation column the 1lb EVO Elite options come paired with our ETL listed 5 liters Neocision heated circulator and the sleeved EVO recovery tank that allows for the pre-chilling of solvent and speedy solvent recovery, reaching sub 20 minute recovery times on high heat. All varients of the EVO Extraction Kits come equipped with a 1.9CFT vacuum oven, a 7CFM single-stage vacuum pump, a 5' HVAC hose, and an 8"x8" silicone pad. The Explorer & Professional models come with the ECO model vacuum ovens and the Elite versions equipped with the ETL list Neocision 1.9CFT vacuum oven. All EVO closed-loop extraction kits come available with an active recovery option including: BVV 2 Cylinder Butane Recovery Pump ITS/ETL to ANSI/ISA Certified BVV Large Condensing Coil 1/2" x 24" SS JIC Braided Hose (2) 1/2" x 48" SS JIC Braided Hose (2) 1/2" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV 5' HVAC Hose BVV Vacuum Tee ***Note: Solvent not included with systems unless ordered separately. Any order with butane WILL NOT SHIP EXPEDITED.*** ***DISCLAIMER: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in extremely well-ventilated areas. Check with your local fire marshal for guidance when operating indoors. KEY BENEFITS Meets or exceeds all industry listed standards Versatile in running butane, propane, and other blended solvents Perfect for mid to large-scale extraction/production facilities Faster run times and less degradation in the process Easy extract harvesting using the elevated pour spout Inline color remediation Extractor Configuration: Explorer: Our standard, most economical setup, perfect for the entry-level extractor on a budget. Comes with the jacketed and elevated collection base and 1/4" Male JIC connections on the injection manifold and collection base. The explorer options include a 1.9CFT ECO Vacuum Oven, a 5' HVAC hose, and a 7CFM single-stage vacuum pump. This model does not include the inline color remediation column or 1/2" Male JIC recovery/ injection connections. The Explorer model is forward compatible and can be easily upgraded to include 1/2" lines and the inline color remediation column. *This model does not come with a heated circulator* Professional: This model includes all the features of the explore model with the increased functionality of an inline color remediation column Just under the material column that comes with 25micron filter paper and a 500-gram sample of b80, an upgraded stainless steel recovery tank, and a full bore 1/2" Male JIC connection included on the injection manifold and collection base. The Professional extraction kit options include a 1.9CFT ECO Vacuum Oven, a 5' HVAC hose, and a 7CFM single-stage vacuum pump.*This model does not come with a heated circulator* Elite: The Elite series is the premium version of the Professional. It features the same 1/2" Male JIC, and inline color remediation column upgrades. But also includes the EVO recovery tank and 5 liter ETL listed Neocision heated circulator that allows for pre-chilling and speedy recovery of solvent. The Elite options include a 1.9CFT ETL Listed Neocision Vacuum Oven, a 5' HVAC hose, and a 7CFM single-stage vacuum pump. Passive: Passive recovery is the standard option on the extraction kit with the explorer model coming with 1/4" recovery lines and the professional and elite models coming equipped with 1/2" recovery lines. Active: The Active Recovery Upgrade Kit will increase recovery times by condensing the vapor a lot faster than just a hot/cold differential. All active models come equipped with 1/2" recovery lines and the inclusion of our BVV 2 Cylinder Butane recovery pump, BVV Large Condensing Coil, Molecular Sieve Filter Drier, and all the associated hosing to perform active recovery. Explorer Professional Elite Jacketed & Elevated pour spout collection base Jacketed & Elevated pour spout collection base Inline Color remediation column 25-micron filter paper 500 gram B80 sample 1/2" recovery lines 30# Stainless steel Recovery Tank Jacketed & Elevated pour spout collection base Inline Color remediation column 25-micron filter paper 500 gram B80 sample 1/2" recovery & Injection lines EVO Recovery Tank 5 liter ETL listed Neocision heated circulator with insulated hoses Unit Includes: Full bore injection Manifold complete with a compound gauge,125 PSI ASME pressure relief valve, and 2x 1/4" MJIC connections (1x1/2" MJIC connection on professional & elite models) 3"x24" 1lb Material column with solvent dispersal plate. 3"x6" Color remediation column 300g gram media capacity complete with a filter stack including 5 micron and 1 micron sintered disks (Professional & Elite model) 25-micron ashless filter paper (Professional & Elite) Jacketed & elevated collection base with extract pour spout 6" hemispherical collection base lid complete with borosilicate sight glasses, a compound gauge, 125 PSI ASME pressure relief valve, and full bore ball valves with MJIC Connections. 30# LP storage and recovery tank (Explorer) 30# stainless steel LP tank (Professional) & EVO Recovery tank (Elite) (1) 1/4" 72" FJIC Stainless Steel Injection hose (Explorer & Professional) 1/2" 96" FJIC Stainless Steel Injection Hose (Elite) (1) 1/4" 60" FJIC Stainless Steel Recovery Hose (Explorer) 1/2" 60" FJIC Stainless Steel Recovery Hose (Professional & Elite) High-pressure clamps Specifications: 3"x 24" 304 Stainless Steel Material Column-1lb capacity (450g) 316 Stainless Steel Fully Encapsulated Miniature Ball Valves System Rated to 150PSI Multiple 37 degree FJIC port connections 304 Stainless jacketed & elevated collection base Tri-Clamps at all interfaces make for a high pressure/standard pressure, easy-clean unit BUNA-N Gaskets are designed for Oil Processing Temp range -40-200F, and have superior solvent resistance Construction: All components are made of 304 Stainless Steel. Max Vacuum -29.9inHg High Polish Interior *Note: Column capacity may vary depending on the density of packed material and packing density. Capacity is calculated using the industry standard of 4.2g/in3. This is the upper limit for column capacity. Low density, uncut, and/or lightly packed material can reduce capacity by 50%. For best results, we recommend to tightly pack coarse ground material.
$6,107.62 - $15,685.52
Safety Tools- 5/8" Combination Wrench
5/8" Combination Wrench This 5/8" combination wrench is made of aluminum bronze, a material that will not spark when accidentally knocked against steel and stainless steel materials. This will limit the sources of possible ignition within a solvent rich environment. This wrench is intended for use on BVV High pressure clamps.
$32.86
Side Mount Tri-Clamp Filter Strainer
Side Mount Tri-Clamp Filter Strainer Tri Clamp strainers are used for filtration of solids from fluid process flows. It is recommended that a strainer be placed before a pump when emptying a centrifuge and the like to not allow large solids to enter and damage a pump. Side Mount Inline Strainers Tri Clamp inline strainers mount similar to a spool or elbow with both ends clamped into a tri-clamp fitting. The side mount strainer has a unique characteristic, it can be emptied while still attached just by removing the internal basket as long as it is correctly mounted. Liquid should flow in through the side port and out through the bottom port.
$271.45
ASME 150L - 350 MAX working pressure, Pneumatic PSIG 385
ASME 150L - 350 MAX working pressure, Pneumatic PSIG 385 This is a custom manufactured made ASME Certified 150L Jacketed Solvent Tank with ASME Stamp and made out of 304 Stainless Steel. This base is designed to be configured to any application and can even be used as a solvent tank. This tank comes bare with no fittings and will hold 150LBS of liquid butane and is able to have fluid circulated around the outer jacket to increase recovery speeds in the extraction system. This unit also has welded lift points on the top of the tank. Specifications Material 304 Stainless Steel Certification: ASME MAWP @ 100°C / 212°F: Inside 350 PSI / 2.42 MPa Jacket 150 PSI / 1.1 MPa MDMT -40°C / -40°F MIN TEMP -20°F at 350PSI Butane Capacity 150LBS Connection Sizes: (3) 6" Tri-Clamp (2) 1.5" Tri-Clamp (2) 1/2" FNPT Weight 108LBS Outer Dimensions: 44.5" Tall 32.5" W x 32.5" L **This Item will ship Via FREIGHT ONLY.
$11,429.47
50L Solvent Pro Rotary Evaporator Bump Trap
50L Solvent Pro Rotary Evaporator Bump Trap Bump Trap to fit 30-50L Solvent Pro rotary evaporators. Connections: Bottom: 50mm ID 70mm OD Right side: 40mm ID 60mm OD Top/Left side: 17mm ID 35mm OD
$964.36
Best Value Vacs 1.5 Gallon Tall Stainless Steel Vacuum Chamber - W/GLASS LID
Best Value Vacs 1.5 Gallon Tall Stainless Steel Vacuum Chamber - W/GLASS LID This is a complete BestValueVac® vacuum chamber setup designed built and 100% tested in Naperville, Illinois. With our unique patent pending gasket design (Patent #9475627) this chamber is sure to last 10,000 uses with proper care and maintenance. The gasket itself is reversible (doubling the life of our system) allowing customers to instantly take it off and flip it over. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. -Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: High Strength Stainless Steel Chamber Highly Durable and Reversible Silicone Gasket Glycerin filled vacuum gauge User-friendly vacuum connections that fit most vacuum pumps on the market 50 Micron Air filter for reducing airborne contaminants when releasing the vacuum Silicone vacuum pad 5' of vacuum rated HVAC hose to pull a vacuum. Specification Chamber Material 304 - 2B Stainless Steel Gasket Material Silicone Lid Material Glass Internal Dimensions (ID) 8-5/8" Tall x 7-1/8" Diameter Vacuum Gauge (Glycerin Filled) InHG (0)-(-30) Manifold Connections 1/4" SAE and 1/4" FNPT Temperature Rating 150°F (65°C) Additional Included Items 5' Purple Vacuum Rated HVAC Hose Platinum Cured Silicone Pad Black 50 Micro Air Filter Compatibility Explanation: BestValueVac® Chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), alcohol, ethanol, acetone and acrylic based monomers or polymers.The lid may only be cleaned with soapy water. DOES NOT APPLY TO GLASS LID VERSION ShatterVac® chambers are not compatible with stabilization resin (i.e. Cactus Juice™, Gator Venom™, Minwax™ etc.), acetone, acrylic based monomers or polymers. The lid may be cleaned with soapy water and low strength cleaning agents. GlassVac® chambers are compatible with all solvents and stabilization resins. We only recommend and warranty GlassVac® chambers for resin infusion and wood stabilization.The lid may be cleaned with any solvent or cleaning agent. See FAQ at the top for product safety warnings. Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Exludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$164.30
NEO Oven PID
NEO Oven PID Specifications NEO PID Temp Range: 0-225°F Temp Accuracy: +/- 1° Built-In Calibration: Yes Temp Display Unit: C or F Timer Range: 0-999 Electrical Requirements: 110v @ 60Hz Compatible Ovens: 09NEO / 19NEO / 32NEO / 75NEO Shipping Dimensions: 5 x 5 x 5 - 1lbs SKU: NEOPID
$371.46
BVV™ Pro Series 35.3CFM Corrosion Resistant Two Stage Vacuum Pump
BVV™ Pro Series 35.3CFM Corrosion Resistant Two Stage Vacuum Pump This is the BVV™ Brand 35.3CFM Two Stage Pro Series vacuum pump. The BVV™ Pro Series 35.3CFM will pull a vacuum down to 0.5 micron effortlessly. The pump is designed with corrosion resistance and long term continuous operation in mind. Comes standard with KF40 fittings, clamps, centering rings and oil mist exhaust filter which returns trapped oil back to the pump and allows for quieter operation. Adjustable gas ballast keeps moisture, solvent, and other contaminants from getting stuck in the pump. Compare to Cacejen or Xeno brand rotary vane vacuum pumps. Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Specifications Electrical Requirements: 220/380VAC 3 Phase - Note this pump does not come with a plug and must be wired manually. Pumping Rate: 35.3CFM Ultimate vacuum without gas ballast: 0.5 micron Inlet/Outlet connection: KF40/NW40 Flange Oil Volume: 4.5L/4.76 quarts Working Temperature: 5C to 40C Unit Weight: 68KG / 150lbs Recommended oil: Ultragrade 19 CE Compliance: yes Warranty 2 year limited warranty Pump Warranty Information: Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$6,571.94
20L Neocision ETL Lab Certified Rotary Evaporator Turnkey System
20L Neocision ETL Lab Certified Rotary Evaporator Turnkey System 20L NEO Rotary Evaporator Turnkey System setup includes all the necessary components to successfully perform solvent recovery via rotary evaporation. A cold trap should always be used inline between your vacuum system and application to protect the pump from volatile vapors. To keep your bath heating properly, this unit should only be used with RO or DI water. 10-50L NEO and ECO Rotary Evaporator Diagram 20L NEO Rotary Evaporator Turnkey System setup includes: 20L Neocision ETL Lab Certified Rotary Evaporator Polyscience 6160T 1HP Chiller 3/8" Gum Rubber - 100ft 3/8" Silicone Tubing - 25ft Welch BTpro100 Diaphragm Pump Adjustable Stainless Steel Hose Clamps Rotovap Quick Start Guide This guide gives basic quick start instructions for rotovaps. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs. Clean and assemble unit. Make sure all pieces are cleaned and sterilized using an alcohol solution. Connect chiller to condenser and set to 0C (32F). Always fill a rotovap condenser from the top down (chiller output to top of condenser, chiller input to bottom of condenser). Connect vacuum pump to cold trap and connect cold trap to vacuum port on rotovap. Turn on heat bath and set to 40C (113F). Once heat bath, chiller and cold trap have reached desired temperatures, turn on rotovap motor and set speed to approximately 100 RPM (does not have to be precise). Keep in mind, higher RPM’s will increase evaporation power but also increase heat load. Start vacuum pump and allow vacuum to pull down for a few minutes before injection. Once vacuum has been pulled to a sufficient level (does not have to be precise but should be below 100 Torr), using the injection valve, very slowly inject approximately 500 mL of solution into evaporating flask and then close the valve. Allow this small amount to begin evaporating. You may see the chiller begin to rise in temperature, this is called “priming” the rotovap. Once the temperature stops rising or all liquid is almost completely evaporated, open the injection valve again very slowly so that a small amount of liquid begins to enter the evaporating flask. Do not close injection valve this time but continue to allow solution to enter the evaporating flask. At this point you must try to match the input speed to the output speed. What this means is that you should be injecting the same amount of liquid into the rotovap that is equal to the amount of liquid dripping from the condenser into the receiving flask. You will know that the input speed and output speed are matched because the chiller will remain at a stable temperature. If the chiller begins to rise, then you are injecting too much liquid. Dial back the valve until the chiller stabilizes. Once everything is stabilized, you may walk away from the rotovap if necessary. Check every so often to make sure temperatures remain stable and evaporation continues efficiently. ***Note: All units are inspected for broken glass or parts before unit is shipped. If unit arrives damaged or glass is broken (this does not include minor imperfections or scuffs in glassware), Customer MUST contact BVV™ within 3 days of delivery to file a claim and receive a replacement part. If customer DOES NOT contact BVV™ within 3 days of delivery responsibility for replacement parts falls on the customer and they must pay for replacement pieces.*** ***Note: This item will ship by freight only.*** ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***
$21,073.08 - $24,723.37
10L Premium Short Path Distillation Kit with P10 Distillation Head
10L Short Path Distillation Kit with P10 Distillation Head This unit carries a 2 day lead time. (Note: Stainless Steel Table NOT Included.) The 10L Short Path Distillation Kit features our USA made P10 Distillation Head. Every component in this turnkey is made for precision, throughput, and repeatable results. Also included the Kangaroo digital thermometer which is very rugged and reliable. You will also receive a Ribbed Dewar Style Glass Cold Trap to keep all volatiles and solvents out of your vacuum system. This Kit gives you the basic necessities of a short path distillation system and allows you to add on a temperature control system and vacuum pump to fit your needs. The 10L Neo Kit Includes: 10L Short Path Distillation Kit including glassware, labware, and P10 Distillation Head. 10L Digital Heating and Stirring Mantle. Valved Vacuum Adapter. Ribbed Dewar Style Glass Cold Trap. Kangaroo Digital Thermometer. Distillation Quick Start Guide This guide gives basic quick start instructions for distillation systems. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs, Before beginning distillation, ensure the following steps have been taken: Vacuum Pump is in good working order. Pump should be run against dry load to allow internals to warm up. Oil should be clear. Cloudy or dark oil should be changed. All glass components are in good working order and ready to be assembled A winterization and degassing procedure has been done to prepare oil for distillation The unit's max internal temperature cannot exceed 380C. The recommended max set temperature should not exceed 250C Once all three of these steps have been completed, you are ready to begin distilling. Begin by placing stir bar in boiling flask and then load your material. This should be done using a funnel. A small amount of alcohol in the oil will give it a thinner consistency making it easier to transfer. Assemble all glassware and ensure each joint is properly greased. Do not use too much, as the vacuum pressure might pull some grease into the system. To ensure a full seal, spread grease in a circular motion by rotating glassware Attach circulator to condenser and set temperature to 50C. Allow circulator to reach temperature before beginning distillation. Connect vacuum pump to manifold. The manifold will allow you to isolate each individual component as well as let atmosphere into and out of the system. Connect receiving cow to cold trap. Connect cold trap to manifold. Connect vacuum gauge to manifold. At this point, ensure all connections are correct. Also ensure receiving cow is positioned to collect the first fraction in the far-left receiving flask. Circulator should be at its set temperature. Turn on vacuum pump to begin process. Turn on heat and set to 60C. Vacuum pump will begin to pull down and temperature will begin to rise. Watch the gauge to monitor vacuum pressure and stability. Start stir slower and increase speed with temperature. Once you are close to 60C, increase the temperature 20 degrees. Continue to raise the heat incrementally in 20-degree steps, increasing the set temperature as you near your set point. Increase temperatures incrementally until you reach 220C. You will see your first fraction somewhere between 180C and 190C or slightly before. This is the “heads” fraction. You will move to your second fraction when you see an increased reaction in the head, a slight color change toward golden, as well as a thickening of distillate. When this fraction hits, allow the distillate to “self-clean” the head for a minute or two then, rotate the cow to the middle receiving flask. Collect your “main body” fraction. You will see temps between 190-220C during this fraction. Continue to increase stirring speed as necessary. Reaction in the head may vary but it should never stop. As fluid level in the boiling flask decreases, increase stir speed. The final “tails” fraction is a mixture of the first and second fractions and should be saved for re-distillation later. Ideally, you want to turn the cow to the final flask before the tails fraction hits. The “tails” fraction has an obvious color change and will be darker than the “main body” fraction. You will see temps between 200-250C during this fraction. As fluid level in the boiling flask decreases even more, set stirring RPM higher (1000+ RPM). You may need to compensate with a bit more heat to finish of the final fraction as well. Once process is complete, stop heat, stop stir, and stop vacuum. Let atmosphere into the system. Be sure to properly store your distillate as exposure to air and light can cause oxidation. ***Note: This entire setup will ship via motor freight.*** *Notice to Customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. BVV™ is not responsible for the failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail, which can cause bodily harm or damage to the surrounding area.
$5,857.60
BVV™ Vacuum Oven Vent Outlet Hole and Cap
Replacement outlet hole and cap for eco and neo oven vacuum release knobs. Note the vent release may require the fitting to be greased to hold vacuum.
$14.29
You have seen 768 out of 813 products