Extractor Upgrades

BVV Tri-Clamp Inline Filter Housing Kit with Free Sample Cartridge Note: Extra Disposable cartridges sold separately. (Click Here for Cartridges) This inline housing allows for implementation of the BVV or AFS filters into many extraction systems.  The BVV filter housing is 2.5" but comes with the adapter flanges for both ends to go inline with a standard 1.5" or 2" tri-clamp system. Kit Includes 1x Free BVV Sample Cartridge (55$ Value!) 2x 2.5" High Pressure Clamps 1x 1.5" or 2" High Pressure Clamp 1x 1.5" or 2" Buna-N Gasket 1x 2.5" Buna-N Gasket 2x Reducers 2.5" to 1.5" or 2" Tri-clamp 1x Cartridge Housing  

Read more less

1LB Inline CRC Kit   BVV's 1lb Inline CRC Kit can be utilized to adapt any of our 3" diameter 1lb material columns for inline adsorbent filtration. This kit includes a 3"x6" media column with a 300-gram media capacity and a filter stack including a 5 micron & 1 micron Dutch Weave Sintered Filter Discs. This 3" color remediation column is meant to be plumbed between the 3" 1lb material column and the existing hemispherical reducer of any of our 1lb closed loop hydrocarbon extractors.Assembly starts with placing the 1 micron sintered disk and gasket between the extracts hemispherical reducer and the included filter plate securing both with one of the included high-pressure clamps. Next, take the 5-micron sintered disk and the included ashless filter paper and rip around the circumference of the sintered disk, placing both atop the filter plate placing the sintered disc gasket and 3"x6" spool over top before securing both with the remaining high-pressure clamp. Since the spool secures the filter paper in place a filter plate ring is not required.  This Kit includes: 3"x6" Tri-clamp Spool (300 gram capacity) 3" V3 Filter Plate 3" 5 Micron Sintered Disk 3" 1 Micron Sintered Disk 2x 3" Buna-N Sintered Disc Gaskets 2x 3" High-pressure Clamp 110MM 25 Micron Ashless Filter Paper (100qty) Your choice of 1000g of UltraClear, B80, Perform 5000 or 500g of Chemtek W1,W2, or W3.   Sample Choices: Ultraclear: High-performance granular attapulgite B80: Naturally active attapulgite clay powder Perform 5000: Highly activated attapulgite clay for hard to bleach oils W1: Top-tier Acid activated bentonite clay perfect for preserving terpenes. W2: Natural bleaching clay that prevents terpene isomerization W3: Highly active adsorptive clay designed for difficult to bleach oils  

Read more less

Inline CRC Kit BVV's Inline CRC Kit can be utilized to adapt any 1.5", 2", 3", 4", or 6" diameter material column for inline adsorbent filtration. This kit includes a corresponding sized media column and a filter stack including a 5 micron & 1 micron Dutch Weave Sintered Filter Disc. This Inline color remediation kit is meant to be plumbed between your existing extractors material column and the existing hemispherical reducer of any closed loop hydrocarbon extractor.Assembly starts with placing the 1 micron sintered disk and gasket between the extracts hemispherical reducer and the included filter plate securing both with one of the included high-pressure clamps. Next, take the 5-micron sintered disk and the included ashless filter paper and rip around the circumference of the sintered disk, placing both atop the filter plate placing the sintered disc gasket and media column spool over top before securing both with the remaining high-pressure clamp. Since the spool secures the filter paper in place a filter plate ring is not required. Media can then be layered into the media column by weight before placing the loaded material column above the adsorbent filtration column and assembling the remainder of the extractor. For optimum filtering results utilize the following layer recipe from top to bottom: 30-50g per lb of biomass Silica 60A 75-100g per lb of biomass Bentonite Clay 30-50g per lb of biomass Neutral Activated Alumina This Kit includes: Media column Tri-clamp Spool V3 Filter Plate 5 Micron Sintered Disk 1 Micron Sintered Disk 2X Buna-N Sintered Disc Gaskets 2X High-pressure Clamps Fast Flow Ashless Filter Paper (100qty) 1000 Gram Sample of B80   *This video provides a visual assembly of the 3" Inline CRC which is applicable across all sizes*

Read more less

Color Remediation Column w/ Bypass The CRC is a secondary column used as a filtration cartridge for hydrocarbon and ethanol extraction systems. Filter medias are packed in the column above a triple filtration stack, which aids in the removal of impurities from extracted oils. The CRC features a bypass path, allowing the operator to skip the column in case of a clog. The color remediation process is made simple by bundling the cartridge with the needed filter medias. We have paired the unit with suggested media, supplied in the proper ratio, and a standard operating procedure. The included procedure takes all the guesswork out of filtration, delivering the desired results the first try. Our CRC comes available with 1/4",3/8", and 1/2" MJIC connections, your choice of a 3",4", and 6" diameter spool with a 12" height, and rack mounting brackets standard to accommodate systems of any size. This Kit Includes: Color Remediation Column Rack Mounting Brackets 100 pack of 8 and 20-micron filter papers 1000g or 2.5 kg of Activated Alumina 1000g or 2.5 kg of Silica 60A 1000g or 2.5 kg of Pure-Flo® B80  (81, 5000, 6000 or Color Bleach)*Substitutes 1000g of Celite®545 Instruction Manual

Read more less

AFS Tri-Clamp Inline Filter Housing for Disposable Color Remediation Cartridges Note: Disposable cartridges sold separately. (Click Here for Cartridges) This inline housing allows for implementation of the AFS filters into many extraction systems.  The AFS filter housing is 2.5" but comes with the adapter flanges for both ends to go inline with a standard 1.5" or 2" tri-clamp system. Kit Includes 2x 2.5" High Pressure Clamps 1x 2.5" Buna-N Gasket 2x Reducers 2.5" to 1.5" or 2" Tri-clamp 1x Cartridge Housing AFS Instruction Manual Download Here   AFS SDS Sheet  

Read more less

AFS Tri-Clamp Inline Filter Housing for Disposable Color Remediation Cartridges Note: Disposable cartridges sold separately. (Click Here for Cartridges) This inline housing allows for implementation of the AFS filters into many extraction systems.  The AFS filter housing is 4" but comes with the adapter flanges for both ends to go inline with a standard 2" tri-clamp system. Kit Includes 2x 4" High Pressure Clamps 1x 4" Buna-N Gasket 2x Flat Reducers 4" to 2" Tri-Clamp 1x Cartridge Housing AFS Instruction Manual Download Here   AFS SDS Sheet  

Read more less

Closed Column Extractor Conversion Kit   This conversion kit will allow you to convert a closed column into a Closed-loop Apollo extractor.   ***Disclaimer: Photos are of 1LB upgrade kit. 135g is not pictured yet.*** The V1 kit will include the following: Extractor Base Hemispherical Extractor Lid with BVV 316SS Full Bore Valves Polycarbonate Sight Glasses (2x) Tri Clamp Clamps Tri-Clamp Gaskets 1.5" 150 Mesh Gasket Stainless Steel Braided Hoses (2x) LP Storage and Recovery Tank The V2 kit will include the following: Extractor Base Splatter Platter Hemispherical Extractor Lid with BVV 316SS Full Bore Valves Polycarbonate Sight Glasses (2x) 1.5" BVV Ball Valve Tri Clamp Clamps Tri-Clamp Gaskets 1.5" 150 Mesh Gasket Stainless Steel Braided Hoses (2x) LP Storage and Recovery Tank

Read more less

The Mini Extractor 135G Upgrade Kit This upgrade kit will increase the capacity of your existing Mini Extractor to a Maximum of 135G This Upgrade Kit Includes:  (2) 4" x 4" Spools (2) 4" Single Pin Tri-Clamps (2) 4" BUNA-N Gaskets (1) 1.5" x 18" Stainless Steel Material Column

Read more less

This Kit Includes Everything needed to upgrade one of our Standard 90-270 gram units up to 1 lb. This Kit Includes the Following Items: Mastercool Green #15 Solvent Recovery Tank 3" x 24" SS304 Spool 3" x 1.5" Conical Reducer 6" x 6" SS304 Spool 3" Top Cap with BVV 316SS Full Bore Valve 6" Single Pin Clamp 6" Buna-N Tri-Clamp Gasket (2) 3" Single Pin Clamps (2) 3" Buna-N Tri-Clamp Gaskets

Read more less

  Pre-Built 12" Collection Base Double your capacity or configure your own custom system with BVV's Pre-Built 12" Collection base. Available in three different variations to suit your application all models of BVV's Pre-Built 12" Collections Base comes standard with high-pressure clamps, borosilicate sight glasses, and full-bore ball valves. Version 1 is the base model equipped with the standard 12" welded base perfect for cost-conscious applications. Version 2 is equipped with a 12"x12" spool & 12" splatter platter to make extract harvesting a breeze, and Version 3 is the top of the line 12" Colleciton base equipped with a 12" jacketed splatter platter for both optimized solvent recovery and ease of harvesting extract.  Specifications High Pressure Clamps 2X 2" Borosilicate Sight Glasses 1X 125 PSI ASME Safety Valves 1X -30hg-250PSI Compound Pressure Gauge 1X 1/2" JIC Lid Valve 2X 1/4" JIC Lid Valves Maximum Pressure Rating: 125PSI Variations V1 : 12x12 Base (1200X12B) V2: 12" Splatter Platter base (1200X12S+1200SPL) V3: 12" Jacketed Splatter Platter Base (1200X12S+1200FJS)  

Read more less

DISCLAIMER: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in extremely well ventilated areas. Check with your local fire marshal for guidance when operating indoors This is a Pre-built Extractor Base for 5LB Icarus with BVV 316SS Full bore valves rated from -40F to 450F.

Read more less

150L 304SS Jacketed Collection and Storage Vessel  (Pre-Built 150L 304SS Jacketed Collection and Storage Vessel with 12" Tri-Clamp Port and Locking Casters)     This massive 304 Stainless Steel Jacketed vessel can hold up to 150L of water (~40 gallons) and has a 12" Tri-Clamp port on the top and a 6" Tri-Clamp port on the bottom of the vessel. The outer jacket has 2x 1/2" FNPT ports to allow the circulation of heat transfer fluids and can also be used a vacuum jacket and can hold 21.5L or 5.68 gallons of fluid in the outer jacket. This unit also features 4 stainless steel legs with locking casters to allow the vessel to be moved around easily. Specifications Material 304 Stainless Steel Connection Type(s): 12" Tri-Clamp Top Ports 6" Tri-Clamp Bottom Port (2) 1/2" FNPT Ports ***Note: This item will ship via freight ONLY.  

Read more less

Closed Loop Recovery Kit This closed loop upgrade kit provides all of the essential ancillary equipment to upgrade an extraction system but does not include an active recovery pump (sold separately). An actively run closed loop extractor will increase productivity by reducing recovery time and overall run time of the system by forcing vapors through a solvent recovery pump. This Kit Includes the Following BVV™ Large Condensing Coil 1/4" x 24" SS JIC Braided Hose (3) 1/4" x 48" SS JIC Braided Hose 1/4" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV™ 5' HVAC Hose Milwaukee Vacuum Tee Note: This kit DOES NOT include a recovery pump and must be purchased separately.

Read more less

This is an Upgrade Kit which can be added to any one of our passive systems making it into an "Active" Closed Loop System. The Active Recovery Upgrade Kit will increase recovery times by condensing the vapor a lot faster than just a hot/cold differential. This will increase efficiency and productivity, many professionals use this method, as this drives profits. This Kit Includes the Following: TRS21 Refrigerant Recovery Pump Best Value Vacs Large Condensing Coil 1/4" x 24" SS JIC Braided Hose (3) 1/4" x 48" SS JIC Braided Hose 1/4" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV 5' HVAC Hose BVV  Vacuum Tee The Upgraded version of the TRS21 comes pre-installed with higher quality internal components that increase recovery speed drastically and also comes with 3/8" JIC and SAE Flares to reduce restrictions in the pump and increase flow/recovery rates. DISCLAIMER: The Upgraded version will still come with standard 1/4" Hoses and Fittings. Upgraded Version Includes: Standard 1/4" Flares Upgraded Inlet/Outlet 3/8" JIC and SAE Flares 2 Piece SS Pistons GEN III Piston Seals Viton O-Rings Stainless Steel Fittings TRS21 Upgrade Kits: TRS21 Upgraded Top Piston Assembly TRS21 Upgraded Stainless Steel 2-Piece Piston and Rod Design for Hydrocarbon Extraction TRS21 Upgraded Compressor head SS ¼” SAE 45D IN and OUT fittings TRS21 Complete Connecting Rod Assembly Upgrade Kit TRS21 2 Piece Piston Tool CPS Rebuild Kits:• TR21X1 Valve Rebuild Kit• TR21X2 Complete Rebuild Kit• TR21X3 Piston Rebuild Kit• TR21X4 Head Rebuild Kit ***Note: Running any solvent that is not authorized by CPS voids all warranty. Running any solvent mixed with any organic plant material will instantly void all warranty. Any Odor coming from the pump or organic plant residuals will also void all warranty.

Read more less

BVV 2 Cylinder Active Closed Loop Recovery Kit ITS/ETL to ANSI/ISA Certified (Pump comes with 1 yr. limited warranty)   This is an Upgrade Kit which can be added to any one of our passive systems making it into an "Active" Closed Loop System. The Active Recovery Upgrade Kit will increase recovery times by condensing the vapor a lot faster than just a hot/cold differential. This will increase efficiency and productivity, many professionals use this method, as this drives profits. This Kit Includes the Following: BVV 2 Cylinder Butane Recovery Pump ITS/ETL to ANSI/ISA Certified BVV Large Condensing Coil 1/2" x 24" SS JIC Braided Hose (2) 1/2" x 48" SS JIC Braided Hose (2) 1/2" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV 5' HVAC Hose BVV  Vacuum Tee   RECOVER MORE WITH LESS BVV is proud to introduce our new and powerful line-up of Butane & Propane Recovery Pumps. Blending compact design with improved Gen III Pistons from RKMAC, this collection of pumps can help you recover 1lb. of butane every 1:40 Seconds!  This pump Assembled in the USA and all the critical parts are domestically made.  Finding parts wont be an issue with this pump.    The piston seals are rated to 450F and the average operating temperature of the pump is 175F leading to a long service life.  Certified by ITS/ETL to ANSI/ISA 12.12.01 for Use in Hazardous locations Class I & II, Division 2 and Class III, Divisions 1 & 2 environments.  The computer controlled brushless DC motor operates at 3000 RMP nearly twice as fast as any other pump in its class.   BVV Butane/Propane Recovery Pumps are: Process up to 10,000 lbs. of vapor recovery before rebuild Equipped with oil-less reciprocating compressors for a clean product Designed and Assembled in the U.S.A. with domestic and global parts Affordable and highly cost efficient Available in 2-Cylinder, 4-Cylinder, CMEP Retrofit Comes with a 1-year Manufacturer’s Warranty covering Hemp usage Rated universal voltage 100-240V AC 50/60 Hz 1Ph Built with high efficiency Brushless DC Motor used for variable speed control Equipped with Viton O-Ring Seals for Butane/Propane gas and oil compatibility Certified by ITS/ETL to ANSI/ISA 12.12.01 Noise level: 90.3 dB at 1m  *Butane recovery results were achieved on a collection base pressure greater than 30psi and using a recovery cylinder with a pressure <10psi.   A dry ice coil was used in between the output port of the pump and the recovery cylinder to condense vapor. 

Read more less

BVV 4 Cylinder Active Closed Loop Recovery Kit ITS/ETL to ANSI/ISA Certified (Pump comes with 1 yr. limited warranty)   This is an Upgrade Kit which can be added to any one of our passive systems making it into an "Active" Closed Loop System. The Active Recovery Upgrade Kit will increase recovery times by condensing the vapor a lot faster than just a hot/cold differential. This will increase efficiency and productivity, many professionals use this method, as this drives profits. This Kit Includes the Following: BVV 4 Cylinder Butane Recovery Pump ITS/ETL to ANSI/ISA Certified BVV Large Condensing Coil 1/2" x 24" SS JIC Braided Hose (2) 1/2" x 48" SS JIC Braided Hose (2) 1/2" x 60" SS JIC Braided Hose Molecular Sieve Filter Drier BVV 5' HVAC Hose BVV  Vacuum Tee   RECOVER MORE WITH LESS BVV is proud to introduce our new and powerful line-up of Butane & Propane Recovery Pumps. Blending compact design with improved Gen III Pistons from RKMAC, this collection of pumps can help you recover 1lb. Butane / 0:51 Seconds!  This pump Assembled in the USA and all the critical parts are domestically made.  Finding parts wont be an issue with this pump.    The piston seals are rated to 450F and the average operating temperature of the pump is 175F leading to a long service life.  Certified by ITS/ETL to ANSI/ISA 12.12.01 for Use in Hazardous locations Class I & II, Division 2 and Class III, Divisions 1 & 2 environments.  The computer controlled brushless DC motor operates at 3000 RMP nearly twice as fast as any other pump in its class.   BVV Butane/Propane Recovery Pumps are: Process up to 10,000 lbs. of vapor recovery before rebuild Equipped with oil-less reciprocating compressors for a clean product Designed and Assembled in the U.S.A. with domestic and global parts Affordable and highly cost efficient Available in 2-Cylinder, 4-Cylinder, CMEP Retrofit Comes with a 1-year Manufacturer’s Warranty covering Hemp usage Rated universal voltage 100-240V AC 50/60 Hz 1Ph Built with high efficiency Brushless DC Motor used for variable speed control Equipped with Viton O-Ring Seals for Butane/Propane gas and oil compatibility Certified by ITS/ETL to ANSI/ISA 12.12.01 Noise level: 93.0 dB @ 1m *Butane recovery results were achieved on a collection base pressure greater than 30psi and using a recovery cylinder with a pressure <10psi.   A dry ice coil was used in between the output port of the pump and the recovery cylinder to condense vapor. 

Read more less

BVV Filter Dryer (Compare to Mastercool 69500-DR Filter Dryer) 1/4" In-Line Liquid filter drier model SDML-032 DM Core - 100% molecular sieves recommended for HFC's with POE and PAG oils.

Read more less

Molecular Sieve Filter Drier A Molecular Sieve Filter Drier is intended to capture moisture and contaminants in the solvent by filter it out while the solvent passes through the Filter Drier. This Filter Drier is made out of 304 Stainless Steel parts and includes High Pressure Clamps, 2x 3" 2500 Mesh (5 Micron) Gaskets to prevent any Sieve dust contaminating the solvent, and 13X Molecular Sieve. The end connections are 37° Flared Connection with a compound gauge that reads (-30)-0-(250Psi).   Specifications Material: 304 Stainless Steel Spool Size: 3" Triclamp x 12" Length End Connections: 1/4", 3/8", or 1/2" 37° JIC Flares Molecular Sieve: 13X Clamps: 3" High Pressure Gaskets: 2x 3" 2500 Mesh (5 Micron) Compound Gauge: (-30-0-(150 Psi)       Size Recommendations: 2LB - Will fit our Molecular Sieve Filter Drier 4LB - Will fit our XL Molecular Sieve Filter Drier 6LB - Will fit our 30LB Extractor

Read more less

Heating Jacket for Best Value Vacs Molecular Sieve Filter Drier   This Heating Jacket will fit the Best Value Vacs Molecular Sieve Filter Drier. It has hook and loop velcro to attach around 3" Diameter columns. The width of the heating jacket measures 240mm (9.45") and the length measures 317mm (12.48")   Feature: UL Listed Fahrenheit Digital Controller. Min Temp: Ambient + 5 Max Set Temp: 160°F Ultimate Max Temp: 248°F Voltage: 110VAC Only Power Consumption:  Digital Control: Increments of 1 Degree. Accuracy: +/- 0.2 Degrees Units: Degrees Fahrenheit Instructions: Fully included Relay Lifespan: Approx. 10 million cycles User can reprogram: Yes

Read more less

Economy Recirculating Heater Kit The Economy Recirculating Heater Kit is designed to provide efficient heating and circulation at an affordable price. The kit includes a submersible water pump for fluid circulation, an LX or MX immersion heater, and all tubing and hose clamps needed to pair with your system. The tubing is 1/2" ID x 5/8" OD and the pump fitting is 1/2". The pump will circulate up to 594 GPH. Economy Recirculating Heater Kit Includes: Polyscience LX or MX Immersion Circulator EcoPlus Eco 633 Fixed Flow Submersible/Inline Pump 594 GPH 5 Gallon Aluminum Pot 10 Feet of 1/2" Silicone Tubing 10 Pack of Adjustable Stainless Steel Tubing Clamps

Read more less

Tri-Clamp/ Tri Clover Top cap with Valve and 1/4" Barb Pre-installed 1/4" hose barb (Fits 1/4" ID Hoses) and 304 stainless steel ball valve on a Tri-Clamp endcap. These endcaps and valves and nitrogen tested for leaks to ensure safe usage of any extraction system. Barb endcaps are useful when connecting flexible tubing to the barb connection to transfer fluids easily or even pull a vacuum on an extraction system instead of using flared connections. ***Note: Please check the pressure rating of the tubing that is going to be used beforehand. Specifications: 304 Stainless Steel Tri-Clamp Endcap 304 Stainless Steel Heavy Duty Ball Valve -40 to 230C (1/4" MNPT/FNPT Connections)  304 Stainless Steel Hose Barb (Fits 1/4" ID Hose) Pre-Assembled and Nitrogen Tested for Leaks at Best Value Vacs Tri-Clamp Sizes Available: 1.5" 2" 3" 4" 6"  

Read more less

Tri-Clamp / Tri Clover Top cap with Valve and 1/4" 37 Degree JIC Flare (Nitrogen Tested)   Pre-installed 1/4" 37 Degree JIC Flare and 304 stainless steel ball valve on a Tri-Clamp endcap. These endcaps and valves and nitrogen tested for leaks to ensure safe usage of any extraction system. Flare endcaps are useful when connecting PTFE lined stainless steel braided hoses to a system because the flared connection type requires NO PTFE tape to create a seal, unlike many threaded connections.     Specifications: 304 Stainless Steel Tri-Clamp Endcap 304 Stainless Steel Heavy Duty Ball Valve -40 to 230C (1/4" MNPT/FNPT Connections) 304 Stainless Steel 1/4" 37 Degree JIC Flare Pre-Assembled and Nitrogen Tested for Leaks at Best Value Vacs   Tri-Clamp Sizes Available: 1.5" 2" 3" 4" 6"  

Read more less

Extractor Top Cap Sight Glass Upgrade This is an extractor top cap sight glass upgrade with a pressure rating of 125PSI. This unit is made entirely of stainless steel components with the exception of the Flare end cap for hose sealing purposes. The recommended applications for this unit is for a Closed Column Extractors and our Closed-Loop Extractors. All fittings are 1/4NPT. The base cap is a Tri-Clamp /Tri-Clover. There are no gaskets or clamps included with this item. This unit will benefit you by allowing you to know when the solvent has filled your material column or to know when the solvent has stopped flowing.  This top cap has a 1/4" JIC Flare with stainless steel butterfly valve rated to -40 to 230C

Read more less

Tri-Clamp/ Tri Clover Build-A-Lid This is the BVV™ Build-A-Lid for standard tri-clamp end caps in which customers are able to make their own lid configuration to suit their needs. The standard lid come with 1/4" 37 Degree Flare and BVV 316SS Full Bore Valves. These lids are pre-assembled and nitrogen tested for leaks at the BVV™ Warehouse to ensure the customer of a leak-free extraction part.   Standard Lid Specifications: BVV 316SS Full Bore Valves 1/4" FNPT 316 Stainless Steel Instrumentation Ball Valve -40F to 450F 1/4" 37 Degree JIC 304SS Flare 1/4" Pipe Nipple 304 Stainless Steel End Cap (Size Picked by Customer)   Upgrade Specifications: Compound Gauge - 1/4" MNPT Compound Gauge (-30)-0-(150PSI) Sight Glass - 1/4" FNPT Stainless Steel Sight Glass

Read more less

6" Pre-Built Hemispherical Lid with BVV 316SS Full Bore Valves (This Lid is fully assembled and Nitrogen Tested for Leaks at Best Value Vacs) This 6" Best Value Vacs Hemispherical lid is fully assembled and nitrogen tested for leaks at our warehouse. This lid comes with 2 BVV 316SS Full Bore Valves with 1/4" 37° JIC Flares, compound gauge and the 4th hole is plugged to allow for future expansion. These lids are made out of 304 stainless steel and have 3 1.5" Tri-Clamp ports with the middle port having an extended tube to control solvent flow. Key Features: Pre-built and Nitrogen Tested for Leaks BVV 316SS Full Bore Valves with 1/4" 37° JIC Flares -40F to 450F 304 High Polish Stainless Steel Compound Gauge (-30)-0-(150PSI)     Specifications Lid Material 304 Stainless Steel Valve Material 316SS Full Encapsulated PTFE Core - 1/4 Turn Flare Size (2)1/4" 37° JIC Tri-Clamp Size(s) (3) 1.5" Ports x 6" Tri-Clamp Nitrogen Tested Yes

Read more less

6" Pre-Built BIFLOW Hemispherical Lid with BVV 316SS Full Bore Valves (This Lid is fully assembled and Nitrogen Tested for Leaks at Best Value Vacs) This 6" Best Value Vacs Hemispherical lid is fully assembled and nitrogen tested for leaks at our warehouse. This lid comes with 3 BVV 316SS Full Bore Valves with (2)1/4" and (1)3/8" 37° JIC Flares, compound gauge and the 4th hole is plugged to allow for future expansion. These lids are made out of 304 stainless steel and have 3 1.5" Tri-Clamp ports with the middle port having an extended tube to control solvent flow. Key Features: Pre-built and Nitrogen Tested for Leaks BVV 316SS Full Bore Valves with 1/4" and 3/8" 37° JIC Flares -40F to 450F 304 High Polish Stainless Steel Compound Gauge (-30)-0-(150PSI) Specifications Lid Material 304 Stainless Steel Valve Material 316SS Full Encapsulated PTFE Core - 1/4 Turn Flare Size (2)1/4" and (1) 3/8" 37° JIC Tri-Clamp Size(s) (3) 1.5" Ports x 6" Tri-Clamp Nitrogen Tested Yes    

Read more less

10" Pre-Built Hemispherical Lid with BVV 316SS Full Bore Valves (This Lid is fully assembled and Nitrogen Tested for Leaks at Best Value Vacs) This 10" Best Value Vacs Hemispherical lid is fully assembled and nitrogen tested for leaks at our warehouse. This lid comes with 2 BVV 316SS Full Bore Valves with 1/4" 37° JIC Flares, compound gauge and the 4th hole is plugged to allow for future expansion. These lids are made out of 304 stainless steel and have (1) 1.5" and (2) 2" Tri-Clamp ports with the middle 1.5" port having an extended tube to control solvent flow. Key Features: Pre-built and Nitrogen Tested for Leaks BVV 316SS Full Bore Valves with 1/4" 37° JIC -40F to 450F 304 High Polish Stainless Steel Compound Gauge (-30)-0-(150PSI) Specifications Lid Material 304 Stainless Steel Valve Material 316SS Full Encapsulated PTFE Core - 1/4 Turn Flare Size (2)1/4" 37° JIC Tri-Clamp Size(s) (1) 1.5" Ports x (2) 2" x 10" Tri-Clamp Nitrogen Tested Yes    

Read more less

10" Pre-Built BIFLOW Hemispherical Lid with BVV 316SS Full Bore Valves (This Lid is fully assembled and Nitrogen Tested for Leaks at Best Value Vacs) This 10" Best Value Vacs Hemispherical lid is fully assembled and nitrogen tested for leaks at our warehouse. This lid comes with 2 BVV 316SS Full Bore Valves with (2)1/4" and (1)3/8" 37° JIC Flares, and compound gauge. These lids are made out of 304 stainless steel and have (1) 1.5" and (2) 2" Tri-Clamp ports with the middle 1.5" port having an extended tube to control solvent flow. Key Features: Pre-built and Nitrogen Tested for Leaks BVV 316SS Full Bore Valves with 1/4" 37° JIC -40F to 450F 304 High Polish Stainless Steel Compound Gauge (-30)-0-(150PSI) Specifications Lid Material 304 Stainless Steel Valve Material 316SS Full Encapsulated PTFE Core - 1/4 Turn Flare Size (2) 1/4" and (1) 3/8" 37° JIC Tri-Clamp Size(s) (1) 1.5" Ports x (2) 2" x 10" Tri-Clamp Nitrogen Tested Yes    

Read more less

12" Pre-Built Hemispherical Lid with BVV 316SS Full Bore Valves (This Lid is fully assembled and Nitrogen Tested for Leaks at Best Value Vacs) This 12" Best Value Vacs Hemispherical lid is fully assembled and nitrogen tested for leaks at our warehouse. This lid comes with 2 BVV 316SS Full Bore Valves with 1/4" 37° JIC Flares, compound gauge and the 4th hole is plugged to allow for future expansion. These lids are made out of 304 stainless steel and have (3) 2" Tri-Clamp ports with the middle 2" port having an extended tube to control solvent flow. Key Features: Pre-built and Nitrogen Tested for Leaks BVV 316SS Full Bore Valves with 1/4" 37° JIC -40F to 450F 304 High Polish Stainless Steel Compound Gauge (-30)-0-(150PSI) Specifications Lid Material 304 Stainless Steel Valve Material 316SS Full Encapsulated PTFE Core - 1/4 Turn Flare Size (2)1/4" 37° JIC Tri-Clamp Size(s) (2) 2" Ports x 12" Tri-Clamp Nitrogen Tested Yes    

Read more less

12" Pre-Built BIFLOW Hemispherical Lid with BVV 316SS Full Bore Valves (This Lid is fully assembled and Nitrogen Tested for Leaks at Best Value Vacs) This 12" Best Value Vacs Hemispherical lid is fully assembled and nitrogen tested for leaks at our warehouse. This lid comes with 2 BVV 316SS Full Bore Valves with (2)1/4" and (1)3/8" 37° JIC Flares, and compound gauge. These lids are made out of 304 stainless steel and have (3) 2" Tri-Clamp ports with the middle 2" port having an extended tube to control solvent flow. Key Features: Pre-built and Nitrogen Tested for Leaks BVV 316SS Full Bore Valves with 1/4" 37° JIC -40F to 450F 304 High Polish Stainless Steel Compound Gauge (-30)-0-(150PSI) Specifications Lid Material 304 Stainless Steel Valve Material 316SS Full Encapsulated PTFE Core - 1/4 Turn Flare Size (2) 1/4" and (1) 3/8" 37° JIC Tri-Clamp Size(s) (3) 2" Ports x 12" Tri-Clamp Nitrogen Tested Yes    

Read more less

8" Pre-Built Hemispherical Lid with BVV 316SS Full Bore Valves (This Lid is fully assembled and Nitrogen Tested for Leaks at Best Value Vacs) This 8" Best Value Vacs Hemispherical lid is fully assembled and nitrogen tested for leaks at our warehouse. This lid comes with 2 BVV 316SS Full Bore Valves with 1/4" 37° JIC Flares, compound gauge and the 4th hole is plugged to allow for future expansion. These lids are made out of 304 stainless steel and have (3) 1.5" Tri-Clamp ports with the middle 1.5" port having an extended tube to control solvent flow. Key Features: Pre-built and Nitrogen Tested for Leaks BVV 316SS Full Bore Valves with 1/4" 37° JIC -40F to 450F 304 High Polish Stainless Steel Compound Gauge (-30)-0-(150PSI) Specifications Lid Material 304 Stainless Steel Valve Material 316SS Full Encapsulated PTFE Core - 1/4 Turn Flare Size (2)1/4" 37° JIC Tri-Clamp Size(s) (3) 1.5" Ports x  x 8" Tri-Clamp Nitrogen Tested Yes    

Read more less

Stainless Steel Ball Valve This is a pre-built and nitrogen tested 1/4 316 Stainless Steel Miniature Ball Valve features a stainless steel ball and PTFE seats and packing on the inside and is rated from -40 to 230C. It comes with a 1/4" 37 degree flare and 1/4" MNPT extender pre-installed on it. The ball valve comes pre-installed with valve and pretaped. This is a standard valve compatible with most closed columns.

Read more less

This valve and gauge adapter allows the user to thread on a gauge and valve to a system or a solvent tank without the need of Teflon tape. This adapter connects with a 1/4" 37-degree Female JIC connection to a 1/4" 37-degree Male JIC connection.

Read more less

This vacuum jacket assembly is pre-assembled to fit on BVV Jacketed Stainless Steel tanks to allow users to create a vacuum jacket around the tank increasing the insulation of the stainless steel LP tank. This assembly comes with pre-taped 1/2" MNPT fitting on the main assembly with a compound gauge and 1/4" 37 JIC flare and BVV butterfly valve. It also comes with a 1/2" MNPT plug for the other port on the tank.

Read more less

FJIC X 3MM Can Adapter This adapter allows the user to seamlessly inject canned solvent into a standard 1/4" MJIC connection without releasing solvent to the atmosphere. This FJIC to 3MM adapter conveniently screws onto any 1/4" MJIC connection allowing for the safe injection of canned solvent into a closed loop system.

Read more less

The Nitrogen Saver Ball Balve can be added to the end of a hose used to prevent loss of solvent or nitrogen when disconnecting a hose. The Nitrogen Saver allows you to seamlessly transfer your nitrogen supply from one vessel to another allowing you to switch from solvent transfer to clearing out the material column with ease. This item is available in 1/4", 3/8", and 1/2" JIC attachments.   **Disclaimer: a hose completely filled with solvent should not be left closed on both ends, the solvent can warm up and build extreme pressure very quickly.

Read more less

Color Remediation Column For BHO Extraction Color Remediation Columns are secondary columns used as a filtration cartridge for hydrocarbon and ethanol extraction systems. Removing impurities from extracted oils is aided by filter media, packed in the column above a triple filtration stack. The CRC features a bypass path, allowing the operator to skip the column in case of a clog. What simplifies the color remediation process is bundling the cartridge with the filter media. We have paired the unit with suggested media, supplied in the proper ratio, and a standard operating procedure. This makes filtration easy, allowing you to get it right the first time without having to guess.  The CRC is a 4" x 12" spool with triple filter plates and rack mounting. Choose 1/4", 3/8" or 1/2" flares. This CRC Kit Includes: Color Remediation Column Rack Mounting Brackets 100 pack of 8 and 20-micron filter papers 1000g of Activated Alumina 1000g of Silica 60 1000g  of Pure-Flo® B80  1000g of PurifiDE XG-12 Instruction Manual

Read more less

Pre-Built BIFLOW Manifold with BVV 316SS Full Bore Valves (This part is fully assembled and Nitrogen Tested for Leaks at BVV™) This BVV™ BIFLOW Manifold is fully assembled and nitrogen tested for leaks at our warehouse. This manifold comes with 2 BVV 316SS Full Bore Valves with (2)1/4" 37° JIC Flares. This manifold is made out of 304 stainless steel with a Tri-Clamp end connection on either side. Key Features: Pre-built and Nitrogen Tested for Leaks BVV 316SS Full Bore Valves with 1/4" 37° JIC -40F to 450F 304 High Polish Stainless Steel 1.5" or 2" Tri-Clamp Connections Specifications Lid Material 304 Stainless Steel Valve Material 316SS Full Encapsulated PTFE Core - 1/4 Turn Flare Size (2) 1/4" 37° JIC Tri-Clamp Size(s) Selectable through Dropdown Nitrogen Tested Yes    

Read more less