LightRail
LightRail
LightRail - RoboStik Lamp Stabilizer
The RoboStik is used for hanging a horizontal reflector from a LightRail 3.0, 3.5 or 4.0 perpendicular to the direction of travel. This item is not needed when hanging a horizontal reflector parallel to the direction of travel, but many creative uses have been found for them. It is packaged with hardware and instructions in a white box with label tape. Light Rail 3.5 is rated to 35 lbsLight Rail 5.0 is rated to 100 lbs Used for hanging a horizontal reflector from a LightRail perpendicular to the direction of travel
$70.95$60.31
LightRail - 5.0 Add-A-Bar Kit
The Light Rail 5 Add-A-Bar kit allows for an additional (3) light maximum expansion to existing Light Rail 5 complete systems. Add-A-Bar kits may need an additional 4' Auxiliary rail (LR5AUXRAIL) for systems that demand more than 2 total crossbar setups. Kit Contains: Adjustable Crossbar (81", 87", 93") Light Rail 5 Auxiliary Trolley Sectioned Push-Pull Rod Mounting Hardware Instructions
$333.53$266.23
LightRail - 3.5 IntelliDrive 10 RPM Kit
For a rectangular growing area, a linear lamp moving system is preferable. The self-propelled Light Rail 3.5 Intelli-Drive is without question the finest linear lamp mover available. It uses no pulleys, chains or gears. Simply mount the standard 6 foot track over the desired area and place the lamp-moving drive motor onto the track. The Light Rail 3.5 Intelli Drive is supplied with adjustable switch stops, so lamp travel can be any length you wish. This is perfect for a start-up size garden through to a full growth garden. The standard 6 foot track may also be extended. Light Rail works great with all reflectors! Light Rail 3.5 is rated to 35 lbs Light Rail 5.0 is rated to 100 lbs
$562.05$380.90
LightRail 3.5 10 RPM IntelliDrive Motor w/0-60 Second Time Delay
LightRail 3.5 IntelliDrive 10 RPM motor travels approximately 4 feet per minute and has a 0-60 second adjustable time delay for pausing the lamp at the ends of its travel. This helps to promote even growth from end to end and allows for equal light-time for the entire run. It comes complete with installation hardware, instructions and a 2-year manufacturer’s warranty. Note: No rail is included. Great for customers who already have a rail or prefer the one-piece 2 meter rail. Light Rail 3.5 is rated to 35 lbsLight Rail 5.0 is rated to 100 lbs Quiet and smooth operation Adjustable time delay from 0-60 seconds Helps to promote even growth
$485.40$349.14
LightRail Motor for 4.0 AdjustaDrive (motor only)
This item is a replacement motor for the LightRail 4.0 AdjustaDrive light mover. It has both a 0- to 60-second adjustable time delay for promoting even growth from end to end plus the added feature of two to four feet per minute adjustable speed control that covers a wide range of lamp intensities and travel distances. Comes complete with installation hardware and instructions. Note: No rail is included. The newest linear light mover available from Gualala Robotics Inc. Zero to 60 second adjustable time delay RPM is adjustable from 6 RPM (2 ft per minute) to 10 RPM (4 ft per minute)
$549.27$395.27
LightRail Add A Lamp Hardware Kit (trolley and mounting hardware)
Add A Lamp Hardware Kit, trolley+mounting hardware The Add A Lamp Hardware Kit includes a trolley and mounting hardware. It is used to hang additional crossbars or reflectors. It can also be used to festoon your power cords or cooling ducts. Light Rail 3.5 is rated to 35 lbsLight Rail 5.0 is rated to 100 lbs Includes trolley and mounting hardware Used to hang additional crossbars or reflectors Can also be used to festoon your power cords or cooling ducts
$96.50$59.22
LightRail Switch Stop Kit for LightRail 3.5/4.0, pack of 6
Switch Stop Kit for LightRail 3.0, 3.5 and 4.0 For replacing the occasional misplaced switch stop. The SS KIT comes with 3 pairs of switch stops and that equals 6 thumb screws and 6 slide nuts. Packaged in a 4" x 4" ziplock. Light Rail 3.5 is rated to 35 lbsLight Rail 5.0 is rated to 100 lbs
$14.18$13.33
LightRail 5.0 Auxiliary Rail
LightRail 5 Auxiliary Rail This is used with LightRail 5 and a second Add a Bar Kit (AAB KIT LR5), see item “R”, to accommodate a 3 crossbar system. The LightRail 5 Auxiliary Rail Item is packed in a tube with installation hardware and instructions. Note: The LightRail 5 Auxiliary Rail does not have rail alignment pins and does not need them because travel across the seam will not be necessary. Great for multiple reflectors Extremely heavy duty and functional90+ lb. capacity if properly balanced Comes with an adjustable crossbar, 8' rail, and high-torque 4 RPM motor
$153.28$137.73