Drying Oven Accessories

The inline candy desiccant dryer is a necessary accessory to any one using a vacuum oven for candy drying.  The column will need to be filled by the user with silica gel and has fine mesh stainless filters on each end to hold in the beads.   We recommend connecting the vacuum inlet from the pump to the top of the column to prevent any water accumulation in the beads from reaching the pump via gravity.  The bottom of the column will connect to the oven itself.  The column holds 1.5lb of silica gel desiccant. Its water holding capacity is 36%.  Since 1lb of candy can hold as much as 40-60g of water, a 1lb column of desiccant will have the capacity to handle approximately 4.5-5lb of fresh candy drying before it needs to be reactivated.  Silica gel can be reactivated by placing in an oven on a sheet pan for 0.5-2.0 hours at 200-250F or microwave for 10 minutes on defrost. BVV Hook Up Guide - Quick Assembly PDF Size Variants Standard Size 2" Outside Diameter x 24" Tall Column (Holds 1.5lbs Silica) XL Size Column 3"  Outside Diameter x 36" Tall Column (Hold 6.5lbs Silica) Extension Kit for the Standard Column 2"  Outside Diameter x 24" Tall (Holds1.5lbs Silica) *Silica Gel: Source from amazon (USE Clear silica gel) https://www.amazon.com/Dry-Quart-White-Silica-Desiccant/dp/B014VM4AZI/ref=sr_1_3?crid=N1FARCPRUFPT&keywords=silica+gel+clear&qid=1678139406&sprefix=silica+gel+cle%2Caps%2C100&sr=8-3

Read more less

ECO Oven Shelf Bracket Kit This bracket kit has an updated design to make it easier to slide the shelves in and out of the oven without breaking the budget.(Note: this kit only fits the Best Value Vacs 0.9CF and 1.9CF ECO Oven line)

Read more less

KF-25 Bellow Fitting Hose Kit This KF25 or (NW25) bellow hose is made out of 304-grade stainless steel which allows a high vacuum to be obtained with a large flow diameter for vapors. These bellow hoses are flexible and allow the user to connect a KF25 flanged vacuum pump to a KF25 flanged vacuum oven or any other application using adapters like our KF25 x NPT or KF25 x Tri-Clamp/ Tri Clover Fittings. This kit also has 2 KF25 clamps and gaskets. What's Included? (1) KF25 Flexible 304 Stainless Steel Bellow Hose (2) KF25 Centering Gaskets with Viton O-ring (2) KF25 Aluminum Clamps Bellow Hose Sizes Available: 1 Meter(s) (3.28 Feet) 2 Meter(s) (6.56 Feet)  

Read more less

Complete KF-25 Flange Kit     The Complete Kit for KF-25 Vacuum Fittings. Connect your flange to a pipe with this complete kit from BVV™. It includes Clamp, O-ring, and Flange

Read more less

Vacuum Filter Trap     This Vacuum Filter Trap is designed to remove potential contaminants from the vacuum line to prolong the lifetime of your pump. Packed with oil-free, stainless-steel SS304 wool and made with a glass jar, the filter trap may optionally be used as a low-cost cold trap. Welch Inlet / Exhaust Separator 1423B with stainless steel wool inside for even more filtration. We built out two separate fitting configurations for your convenience: just choose from the drop-down menu above! The trap ships default with two 3/8" Barbed fittings, but you may alternatively select our KF25 x 1/4" JIC fittings to receive your vacuum trap specially designed for use with our ovens! Simply clamp the trap directly onto your oven's KF25 vacuum port, then connect a 1/4" hose to your vacuum pump. Specifications: Inlet/Outlet: 3/8" FNPT (ships with adapters selected above) Jar: 230ml Glass -- Welch Inlet / Exhaust Separator 1423B Steel Wool: Oil-free SS304 Maximum Vacuum: <29"Hg Dimensions: 2.8" dia x 4.3" tall   Please note this item does not include any vacuum tubing. To order, we recommend the 3/8" Gum Rubber Vacuum Tubing.

Read more less

This Unique 304 Stainless Steel KF-25 Y Bellow has 3 attachment points for KF-25 fittings and 2 flexible ends and 1 rigid end that let the user position them the way that best suits their operation. It has an overall length of 17" and a width of ~16".

Read more less

This 304 Stainless Steel KF Vacuum Flange Reducer / Adapter is designed to convert K16 to KF25 or KF25 to K40 and vise versa.

Read more less

ECO Oven Shelves These are stainless steel oven shelves for BVV™ ECO Ovens and fit either a 0.9CF or a 1.9CF ECO Oven. Specifications:  0.9CF - 10.9" (278mm) x 11.2" (285mm) x 1/8" Thickness 1.9CF - 14.1" (359mm) x 15.4" (392mm) x 1/8" Thickness

Read more less

Cold Trap 2" Stainless Steel This Stainless Steel Cold is designed and intended for use with the Polyscience IP60 Cold Finger (Can also be used with dry Ice) to create a cold trap that can achieve extremely frigid temperatures. These cold traps have 2 1/4" FNPT ports with one having a dip tube to the bottom of the trap to achieve higher vapor condensing rates with the 2" Diameter Center opening for the IP60. This Cold trap also has an insulating vacuum jacket around the entire container to maintain the subzero temperatures and help achieve the maximum minimal temperature of the IP60. Unlike many cold Traps on the market, this one is also made out of 304 Stainless steel and the internal parts are resistant to most chemicals and easily cleaned due to the Tri-Clamp lid design. Specifications Material 304 Stainless Steel Temperature Rating -200 to 200°C Ultimate Vacuum <100millitorr / microns Cold Finger Internal Dimensions 1.85" x 11.75" (Fits Polyscience IP60) Trap Internal Dimensions 5.85" x 10" Outside Dimensions 8" x 14" x 15" (Includes jacket gauge and valve hardware) Weight 28LBS    

Read more less

KF-25 x Barb Adapter This 304 Stainless Steel KF-25 adapter is fitted with a 304 stainless hose barb adapter to connect a vacuum pump or vacuum oven to a flexible rubber hose.

Read more less

KF-25 x JIC Flare Adapter This 304 Stainless Steel KF-25 adapter is fitted with a 304 stainless 37° JIC Flare adapter to connect a vacuum pump or vacuum oven to a stainless steel braided chemical hose or a hvac hose.

Read more less

Adapts to the 1/4" connections for most vacuum pumps on the market.

Read more less

NEO Oven PID   Specifications NEO PID Temp Range: 0-225°F Temp Accuracy: +/- 1° Built-In Calibration: Yes Temp Display Unit: C or F Timer Range: 0-999 Electrical Requirements: 110v @ 60Hz Compatible Ovens: 09NEO / 19NEO / 32NEO / 75NEO Shipping Dimensions: 5 x 5 x 5 - 1lbs SKU: NEOPID

Read more less

KF Flange x FNPT Adapter KF- or NW Vacuum fittings are designed for Ultra-High-Vacuum applications and are made out of 304 stainless steel. These fittings require a special gasket with metal centering ring to not allow over compression of the gasket. These fittings have female NPT threads that come in a variety of sizes, Female NPT threading which require thread sealant if they are installed to another NPT adapted fitting.

Read more less

Heavy Duty Steel Mobile Cart for Vacuum Ovens Our heavy-duty cart is designed and built to house a variety of equipment such as vacuum ovens, cold traps, vacuum pumps, etc. The cart can comfortably house up to 3 BVV™ and Across International 0.9 and 1.9 vacuum ovens. The cart offers mobility with their swivel caster wheels and can withstand up to a total of 1,100lbs. Included in the unit are three side shelves in which the height can be adjusted to your needs. The cart was meticulously designed for reliability, customization, and convenience for your process. Features: White powder coated carbon steel. 3-shelf shelving unit 3 laser cut, height adjustable side shelves. 2⅜” diameter hole to help with hose and cable management. 6” front lip for easy oil drainage. Can fit on the left or right side of the bracket Four 3” swivel caster wheels: 2 with brakes and 2 without brakes. Dimensions: 33” (L) x 23” (W) x 61” (H). Additional 13¼” to the length with side shelves added. Made in the USA. Note: The unit shipped does NOT come with the side shelves assembled. Required tool: 5mm ball hex (NOT INCLUDED).

Read more less

Heavy Duty Steel Mobile Cart Shelves These are additional shelves that are designed to go with our Heavy Duty Steel Mobile Cart for Vacuum Ovens. These shelves can also fit on either the left or right side of the bracket. What is Included: 1x Shelf 2x Support Brackets (Left and Right Side) 8x M8 Screws + Washers Note: Product does NOT come assembled. Required tool: 5mm ball hex (NOT INCLUDED).

Read more less

Heavy Duty Aluminum Oven Tray   This oven tray is a perfect addition to our 1.9 and 0.9 cubic foot vacuum ovens.  For those hard to keep in place items or to keep objects from rolling off our shelves.  Our trays are a perfect fit, maximizing all of the shelf space possible. They are heavy weight material heats quickly and provides even heat distribution to deliver the quality results you expect. These trays will sit right on top of your existing shelves.  They will not sit on the shelf guides in any of the ovens, the existing shelf is needed for support.  10x10 Tray for the 0.9 NEO & ECO model vacuum ovens. 14x14 Tray for the 1.9 Neo & ECO model vacuum ovens.  This 1" deep tray is made of 14 gauge, 1.5 mm thick heavy weight aluminum! This material resists rust, corrosion, and warping for a tray that will last.

Read more less

KF Stainless Steel Bellow Hose    This KF or NW flange bellow hose is made out of 304-grade stainless steel which allows a high vacuum to be obtained with a large flow diameter for vapors. These bellow hoses are flexible and allow the user to connect a KF flanged vacuum pump to a KF flanged vacuum oven or any other application using adapters like our KF x NPT or KF x Tri-Clamp Fittings.

Read more less