BVV
-
TRS21 Complete Connecting Rod Assembly Upgrade Kit
BVV-K1 Included in this kit: Complete connecting rod assemblies with 2-piece SS piston, piston seals, viton o-rings, and 2-piece piston tool. Looking to rebuild your TRS21 and want to upgrade to a more efficient and longer lasting piston/rod setup? This kit comes with a fully assembled connection rod and 2 piece piston. The piston is made out of SS making it a great choice for any application where bacterial growth must be eliminated. This design focuses on long life piston seal and wear band. This kit utilizes a Viton energized o-ring specifically designed for butane and or propane recovery used in the extraction process. By utilizing this kit the piston seal and wear band can be easily removed without having to disassemble the rod from crank. An inexpensive tool (*INCLUDED* SKU: BVV-TL1) is required to rebuild the seals next time service is needed. The tool uses two posts to lock into the top of the piston and a 5/8” Hex heat to remove the top part of the piston. After this has been done the wear ring can slide out and the piston seal can be replaced with a new one, the kit can be purchased for all future piston seal and wear band rebuilds (*NOT INCLUDED* SKU: BVV-3). Loctite 242 (*NOT INCLUDED*) will also be required for proper installation. A test was performed between the OEM piston and seal design and the BVV. Results show that the BVV had a much less leak rate than the OEM design. After hours of use the leak rate of the OEM design was unable to recover the complete initial solvent batch. This affects the efficiency of the recovery process.
$225.88
-
TRS21 Upgraded Compressor head SS ¼” SAE 45D IN and OUT fittings
BVV-9-1 Included in this kit: TRS21 compressor head SS ¼” SAE 45D IN and OUT fittings, Viton o-rings. Use these fittings to replace the OEM brass fittings on your TRS21. The SS fittings minimize and help eliminate bacterial growth in the recovery process.
$39.53
-
TRS21 Upgraded Cylinder Replacement Kit, w/Shims Fits BVV4CYL & BVV2CYL
BVV-6 Included in this kit: (2x) Anodized Aluminum Cylinders and Viton Gaskets, Plus 6 shims (2x .004" and 2x .002") use for top dead center adjustment of the cylinders to dial in the displacement (recommended displacement .008"). This upgrade kit can be used for the following recovery pumps: CPS TRS21 Anti-spark/explosion pump (including the SS model from BVV) BVV 2 Cylinder Butane Recovery Pump ITS/ETL to ANSI/ISA Certified BVV 4 Cylinder Butane Recovery Pump ITS/ETL to ANSI/ISA Certified - Requires 2 kits because this unit has 4 cylinders. BVV 4 Cyl & 2 Cyl Pump Seal Rebuild Instructions
$148.23
-
TRS21 Valve Head Complete Viton O-ring Kit
Replacement kit with Viton O-rings for the TRS21 head. Compatible for use with the Oil Extraction Market, Butane and Propane Extraction solvents.
$38.12
-
Tube Stub X MJIC Adapter
Tube Stub X MJIC Adapter This stainless steel tube stub adapter can be used to convert a compression fitting to a JIC connection. The tube stub size will be the OD of the compression pipe fitting. This will fit with Swagelok or other comparable compression fittings.
$24.00 - $28.23
-
UL Listed BVV™ Pro Series 21.2CFM Corrosion Resistant Two Stage Vacuum Pump
UL Listed BVV™ Pro Series 21.2CFM Two Stage Vacuum Pump (Pump holds a 1 year limited warranty) This is the BVV™ Brand 21.2CFM Two Stage Pro Series vacuum pump. The BVV™ Pro Series 21.2CFM will pull a vacuum down to 0.3 microns effortlessly. The pump is designed with corrosion resistance and long-term continuous operation in mind. Comes standard with K-25 fittings, clamps, centering rings and oil mist exhaust filter which returns trapped oil back to the pump and allows for quieter operation. Adjustable gas ballast keeps moisture, solvent, and other contaminants from getting stuck in the pump. Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Specifications Electrical Requirements: 110v 60Hz 1100 Watts Pumping Rate: 21.2CFM Ultimate vacuum without gas ballast: 0.3 micron Ultimate vacuum with gas ballast: 6 micron Inlet/Outlet connection: KF25/NW25 Flange Oil Volume: 2L/2.1 quarts Motor Rate: 1720 RPM Working Temperature: 5C to 40C Unit Dimensions: 21 x 7.5 x 12 Shipping Dimensions: 29.5 x 9.5 x 16.5 Unit Weight: 95lbs Shipping Weight: 105lbs Recommended oil: Ultragrade 19 Noise level: <58 dB CE Compliance: Yes Warranty: 1 year limited warranty Pump Warranty Information Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result in the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$4,941.10
-
UL Listed BVV™ Pro Series 5.6CFM Corrosion Resistant Two Stage Vacuum Pump
UL Listed BVV™ Pro Series 5.6CFM Two Stage Vacuum Pump (Pump holds a 1 year limited warranty) Features Our Pro series are our most impressive line of rotary vane pumps available. Known for their high degree of efficiency and deep ultimate vacuum, all Pro models feature a dual-stage, chemical-resistant pump configuration designed to handle abusive, extended vacuum evacuations. Capable enough to comfortably handle laboratory and scientific applications, these pumps are also extremely simple in operation and require minimal maintenance. PTFE chemical resistant pump vanes provide superior corrosion resistance and reliability. Large oil reservoir and adjustable gas ballast standard on every model to increase pump oil lifetime. Internal check-valve included in every unit, prevents accidental pump oil backflow. Exhaust oil filter trap included. DEEP ultimate vacuum and KF25 inlet for optimal pumping speed. Lightweight, with noise-dampening rubber feet. Rugged, reliable, economical, and efficient pump designed for day in, day out use. Air cooled, thermally protected motors enclosed in a durable aluminum housing. Gas ballast valve for deeper vacuum. Steel inlet KF25 flange port with multiple intake size. Plastic handle, skid-resistant rubber base. 1 year limited warranty. Specification Electrical Voltage 120v Frequency 60 Hz Plug NEMA 5-15 US Standard Pump Flowrate 5.6 CFM Configuration 2 Stage Pump Ultimate Vacuum 0.3 Micron Ultimate Vacuum (with ballast) 6 Micron Oil Capacity 1000 ml Recommended Oil Ultragrade 19 Motor Power 1/2 hp Max Speed 1720 RPM Noise Level <56 dB Package Inlet / Exhaust KF25 / NW25 Weight 46 lbs Compliance CE Listed Ships With Exhaust Filter, Pump Oil, User Manual, Power Cable Warranty 1 year Components Pro Series Pump Components(Included exhaust filter not pictured) Performance Comparison Pump speed comparison for our Pro Series pumps. Downloads Maximum Attainable Vacuum at Altitude Reference Chart Vacuum Units Conversion Chart Additional Information How do Rotary Vane pumps work? Rotary vane pumps work by having a rotor with two adjusting vanes continuously rotating and exhausting air or any other molecules in the occupied space. The four stages which a rotary vane pump undergo are shown below Single Stage vs Two Stage Vacuum Pump: BVV™ Pro Series pumps are a dual-stage rotary vane pump style. Dual-stage pumps have two rotors and two sets of vanes that work together to fully pull a medium vacuum (1st stage) and then pull a better vacuum (2nd stage). These pumps will evacuate more quickly and can pull a deeper vacuum when compared to single-stage pumps. What is Gas Ballast and how does it work? During the pumping process the vacuum pump is trying to evacuate gas present in the occupied space, both non-condensable and condensable gases and vapors. Gas ballast helps increase the percentage of non-condensable vapors such that it will allow for the pump to efficiently exhaust all gases and vapors. This in turn will increase the overall efficiency and pumps life. When the pump is being used with non-condensable gases it's safe to keep the gas ballast valve closed. On the other hand, when there is a condensable gas or vapor present, the gas ballast should be opened appropriately. Gas ballast is used at the beginning of the pumping process when condensable gases are known to be present, then it's closed to finish pulling the deepest vacuum. For more info on rotary vane pumps please view our blog post: Rotary Vane Pumps and Gas Ballast Explained. Pump Warranty Information Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$2,470.55
-
UL Listed Pro Series Vacuum Pump Complete Service Kit
Pro Series Vacuum Pump Complete Service Kit This is a compelete vacuum pump service kit for the BVV™ Pro Series 5.6, 11.3, 21.2CFM line of vacuum pumps and allows the user to completely rebuild their pump and keep it running like new.
$451.76 - $494.11
-
Ultra Clear - Granular High Performance Bentonite for Bleaching & Decolorizing Edible Oils
Ultra:Clear® 30/60 Mesh, Compare to Media Bros CRX™ Made in USA, Food Grade Certified Ultra-Clear® effectively removes color bodies, surfactants, water, free fatty acids, organic oxides, and other polar contaminants from a wide range of oils, liquids, and waxes. This High-Flow media is amazing for color remediation CRC and has a 30/60 mesh granule size to get color remediation done quickly with low pressure drops. This media you will be sure to love. At BVV™ we recommend 100g per lb. of biomass. We also use this media with layering techniques & can be used with BVV™ Silica Gel and BVV™ Neutral Activated Alumina for a sugar in the oven finish! Save big on buying the 50lb Bag(s). Ultra:Clear is manufactured in 3 granule sizes, 8/16, 16/30 & 30/60 Mesh sizes. The smallest size granules are the 30/60 and will offer the greater surface area while retaining a High-Flow media for your extraction. See the technical data sheet for more information from the manufacturer. Ultra:Clear® Food Grade Certificate Ultra:Clear® Technical Data Sheet Ultra:Clear® Safety Data Sheet
$49.41 - $3,882.29
-
Ultra Clear L - Granular High Performance Bentonite for Bleaching & Decolorizing Edible Oils
Ultra:Clear® L 8/16 Mesh Made in USA, Food Grade Certified Ultra-Clear® L effectively removes color bodies, surfactants, water, free fatty acids, organic oxides, and other polar contaminants from a wide range of oils, liquids, and waxes. It is the Largest particle size in the Ultra-Clear product line. UltraClear® L is a unique, naturally occurring attapulgite that has been thermally processed to provide hard, durable granules that won’t swell or breakdown in the presence of water. All Ultra-Clear products are classified as processing aids andhave Generally Recognized As Safe (GRAS) status from theFood and Drug Administration (FDA). At BVV™ we recommend 200g per lb. of biomass. We also use this media with layering techniques & can be used with BVV™ Silica Gel and BVV™ Neutral Activated Alumina for a sugar in the oven finish! Ultra-Clear® is manufactured in 4 granule sizes, 8/16, 16/30, 30/60 & 60/90 mesh sizes. See the technical data sheet for more information from the manufacturer. Ultra:Clear® L Food Grade Certificate Ultra:Clear® L Technical Data Sheet Ultra:Clear® L Safety Data Sheet
$49.41 - $3,882.29
-
Ultra Clear M - Granular High Performance Bentonite for Bleaching & Decolorizing Edible Oils
Ultra:Clear® M 16/30 Mesh Made in USA, Food Grade Certified Ultra-Clear® M effectively removes color bodies, surfactants, water, free fatty acids, organic oxides, and other polar contaminants from a wide range of oils, liquids, and waxes. It is the Second Largest particle size in the Ultra-Clear product line. UltraClear® M is a unique, naturally occurring attapulgite that has been thermally processed to provide hard, durable granules that won’t swell or breakdown in the presence of water. All Ultra-Clear products are classified as processing aids andhave Generally Recognized As Safe (GRAS) status from theFood and Drug Administration (FDA). At BVV™ we recommend 150g per lb. of biomass. We also use this media with layering techniques & can be used with BVV™ Silica Gel and BVV™ Neutral Activated Alumina for a sugar in the oven finish! Ultra-Clear® is manufactured in 4 granule sizes, 8/16, 16/30, 30/60 & 60/90 mesh sizes. See the technical data sheet for more information from the manufacturer. Ultra:Clear® M Food Grade Certificate Ultra:Clear® M Technical Data Sheet Ultra:Clear® M Safety Data Sheet
$49.41 - $3,882.29
-
Ultra Clear S - Granular High Performance Bentonite for Bleaching & Decolorizing Edible Oils
Ultra:Clear® S 60/90 Mesh Made in USA, Food Grade Certified Ultra-Clear® S effectively removes color bodies, surfactants, water, free fatty acids, organic oxides, and other polar contaminants from a wide range of oils, liquids, and waxes. It is the Smallest particle size in the Ultra-Clear product line. UltraClear® S is a unique, naturally occurring attapulgite that has been thermally processed to provide hard, durable granules that won’t swell or breakdown in the presence of water. All Ultra-Clear products are classified as processing aids andhave Generally Recognized As Safe (GRAS) status from theFood and Drug Administration (FDA). At BVV™ we recommend 100g per lb. of biomass. We also use this media with layering techniques & can be used with BVV™ Silica Gel and BVV™ Neutral Activated Alumina for a sugar in the oven finish! Ultra-Clear® is manufactured in 4 granule sizes, 8/16, 16/30, 30/60 & 60/90 mesh sizes. Ultra-Clear® S is the smallest particle size and will offer the greatest surface area while remaining a High-Flow media for your extraction. See the technical data sheet for more information from the manufacturer. Ultra:Clear® S Food Grade Certificate Ultra:Clear® S Technical Data Sheet Ultra:Clear® S Safety Data Sheet
$49.41 - $3,882.29
-
ULTRA-Low Chest Style Freezer (-60°C) 10.6 Cubic Feet
ULTRA-Low Chest Style Freezer (-60°C) 10.6 Cubic Feet Single Compressor Model, Best Pick for Energy Savings! The brand new BVV™ 10.6 cubic foot -60°C Ultra-Low Chest Freezer is a great all-around ultra-low temperature freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting. These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. Key Features: Durable Powder Coated Exterior Aluminum Interior CFC-Refrigerant Free Large Digital Display Heavy Duty Rolling Casters 2 Wire Baskets for Extra Storage and Organization Specifications Model Number BVV™-60C106 Voltage 115V / 60Hz / 15A Capacity 10.6 Cu Ft. Temperature Range -30°C to -60°C Exterior Dimensions 50" x 30.1" x 34.8" Interior Dimensions 42.5" x 19.1" x 23.6" Weight 167lbs
$4,799.93
-
ULTRA-Low Chest Style Freezer (-86°C) 4.5 Cubic Feet
4.5 Cubic Feet Chest Freezer, Ultra Low Temperature The brand new BVV™ 4.5 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. It contains a dual independent refrigeration system inside and a SECOP compressor. This unit will run productively and efficiently, with a sleek design that will fit any lab or office setting. Every freezer unit includes various safety and protection features for both user and item safety. Features include high and low-temperature alerts and even a locking door. These compact chest freezers are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended for storage of pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. The freezer can fit up to two 5 gallon buckets inside. Key Features: 3 Ports to allow tubing or probes. SECOP Compressor Durable Powder Coated Exterior Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters Specifications Model Number BVV™-86C45 Voltage 115V / 60Hz Wattage 500w Capacity 128L / 33.8G Temperature Range -40°C to -86°C Exterior Dimensions 32.3" x 28" x 39.3" Interior Dimensions 25" x 17.5" x 18" Weight 197lbs
$6,352.84
-
Ultra-Low Chest Style Freezer with Touch Screen LCD (-86°C) 16.2 Cubic Feet - ETL Rated
ULTRA-Low Chest Style Freezer with Touch Screen LCD (-86°C) 16.2 Cubic Feet - ETL Rated The brand new Neocision ETL Rated 16.2 cubic foot -86°C Ultra-Low Chest Freezer is a lab grade freezer at an affordable price with great temperature stability. This unit will run productively and adequately while brandishing a sleek design that will fit any lab or office setting. Every unit accompanies various safety and protection features taking into consideration user and item safety. These highlights incorporate high and low-temperature alerts. These units are appropriate for emergency clinics, creature cultivation, pharmaceutical organizations, and research foundations. They are intended to store pharmaceuticals, medication, immunizations, natural materials, testing reagents, research facility materials and can likewise be utilized to pre-chill solvents or winterize material. Key Features: ETL Rated Durable Powder Coated Exterior Touch Screen LCD with Datalogging Capabilities Stainless Steel Interior CFC-Refrigerant Free Power Failure and Over Temp Alarm High and Low Temp Alarms Large Digital Display Heavy Duty Rolling Casters (3) 1" ID Ports for putting lines through the freezer Backup battery Included. Specifications Model Number NEO-86C162 Voltage 115V / 60Hz / 13A Wattage 1560w Capacity 16.2cu ft. / 458L / 121G Temperature Range -40°C to -86°C Exterior Dimensions 79-3/4" x 36" x 40" Interior Dimensions 51-1/2" x 23" x 25" Weight 529lbs Certification ETL Rated
$8,329.28
-
Ultrapure RODI Water USP
Ultrapure RODI Water USP Made in USA Ultrapure Reverse Osmosis Deionized (RODI) water meeting USP (United States Pharmacopeia) standards is highly purified water treated through multi-stage filtration, RO, and DI to remove ions, organics, and microorganisms. Our waters TOC (Total Organic Carbon) is ~9 Parts per Billion! Organic carbon-containing compounds can either be dissolved in water or exist in water as undissolved, suspended material, or liquid. This organic matter can enter water naturally and through man-made sources/processes. The standard calls for less that 500 Parts Per billion. That means this water is ultrapure containing barely any carbon containing compounds. *Packaged in FDA Compliant HDPE Bottles. Each order is poured directly from the factory drum ensuring you get the freshest stock upon delivery. Ultrapure RODI Water USP Sample Certificate of Analysis (COA Example) Ultrapure RODI Water USP Safety Data Sheet SDS
$31.06 - $458.82
-
Ultrasonic Cleaners
BVV™ Ultrasonic cleaners are the industry standard for lab and industrial grade applications and are made out of high quality stainless steel. Ultrasonic cleaning uses cavitation bubbles induced by high frequency pressure (sound) waves to agitate a liquid. The agitation produces high forces on contaminants adhering to substrates like metals, plastics, glass, rubber, and ceramics. This action also penetrates blind holes, cracks, and recesses. The intention is to thoroughly remove all traces of contamination tightly adhering or embedded onto solid surfaces. Water or solvents can be used, depending on the type of contamination and the workpiece. Contaminants can include dust, dirt, oil, pigments, rust, grease, algae, fungus, bacteria, lime scale, polishing compounds, flux agents, fingerprints, soot wax and mold release agents, biological soil like blood, and so on. Ultrasonic cleaning can be used for a wide range of workpiece shapes, sizes and materials, and may not require the part to be disassembled prior to cleaning. Specifications Model LS-30L IS-77L IS-264L Material Stainless Steel Stainless Steel Stainless Steel Reservoir Capacity 30L (7.9 gal) 77L (20.3 gal) 264L (70 gal) Exterior Dimensions 13" x 22" x 13-1/4" 23-1/2" x 31.5" x 32-1/8" 35" x 55-1/2" x 36" Weight 22lbs 130lbs 250lbs Reservoir Dimensions 11.5" x 19.5" x 7-3/4" 15-5/8" x 21.5" x 13-3/4" 23.5" x 31-3/8" x 21.5" Tray Dimensions 9-5/8" x 17.5" x 5" 18-7/8" x 14-1/8" x 7-1/2" 21-3/4" x 28.5" x 9-3/4" Ultra Sonic Power 600w 1200w 3000w Heating Power 500w 3000w 6000w Voltage 110v/60Hz 110v/60Hz 220v/60Hz 3 Phase Casters No (Rubber Feet) Yes (Locking) Yes (Locking)
$917.63 - $5,294.04
-
Universal Drum Wrench, Aluminum Alloy
This is an aluminum alloy universal drum wrench that is used on 3/4" and 2" drums and barrel bungs. This lightweight wrench can be used to open bungs and is capable of quarter turns in tighter spaces. Perfect for various facility and warehouse uses.
$26.82 $18.35
-
Universal Vacuum Chamber Gasket
Universal Vacuum Chamber Gasket Our patented gasket #9475627 This vacuum chamber gasket is made out of durable and heat resistant silicone. It features a large flange on a single side so the user can adapt one of our lids to varyingly sized vessels. Gasket Specifications: 10.75" - Can Fit lids 10.75" in Diameter and up to 3/4" in thickness 12.75" - Can Fit lids 12.75" in Diameter and up to 1" in thickness
$56.47 - $63.53
-
Upgrade Tool for TRS21 Suction Valve
Our specialized tool for use with rebuilding the head on TRS21, makes installation of new Suction Valve O-Rings much easier. Includes (5) Viton O-rings.
$25.41
-
Upgraded TRS21 Compressor Head
Upgraded TRS21 Compressor Head Complete, Stainless Fittings, Viton Upgrade your TRS21 by purchasing a new Compressor Head with Viton O-rings for butane and propane gas compatibly and stainless steel fittings to meet FDA guidelines on handling of consumable products. This head is assembled here in the USA and is a direct replacement for any TRS21 Compressor Head.
$254.11
-
Urea High Purity 46% High Nitrogen (46-0-0)
Industrial Grade Urea 46% High Nitrogen (46-0-0) is a highly concentrated granular form of fertilizer containing 46% nitrogen by weight. This product is fast-acting, water-soluble and can be added to soil or made into a liquid solution and sprayed on vegetables, trees, and of course the lawn. Urea is relatively safe to handle, its non-toxic to humans and animals, and does not accumulate in soil. Urea Certificate of Analysis (Example COA) Urea Safety Data Sheet (SDS)
$14.10 - $70.59
-
V4D 4CFM Two Stage Vacuum Pump
BVV™ V4D 4CFM Two Stage Vacuum Pump This is the BVV™ V4D 4CFM Two Stage Vacuum Pump used in botanical extraction. Please refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Feature Internal Check Valve Oil Mist Filter Cap Larger Oil Reservoir for longer oil life Lightweight Rubber Feet for noise dampening Reliable, economical, and efficient Models BVV4D BVV7S BVV9D Stage 2 1 2 Ultimate Vacuum (Microns) 15 75 15 Refrigerant Classes A1 Non-Toxic, Non Flammable Dimensions (in) 12.4 x 4.8 x 10.16 12.4 x 4.8 x 10.16 15 x 6.3 x 11.22 Weight (lbs) 19.4 16.5 32 Free Air Displacement 4.3 CFM 6.4 CFM 8.5 CFM Motor Size (HP) RPM 1 HP 3440 RPM Oil Capacity 10oz / 300ml 14.5oz / 410ml 24oz / 680ml Voltage 110V 60 Hz Power Cord Hard Wired 3m / 9.8' Power Cord Power Switch Standard On / Off Operating Temperature Range 32F to 125 F (0C to 52C) Gas Ballast Valve Yes No Yes Intake Fittings Stainless Steel Inlet Fitting with 1/4" SAE & 3/8" JIC Male Ports Pump Warranty Information Customers using solvents such as stabilization resin, rotaries (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$501.17
-
V7S 7CFM Single Stage Vacuum Pump
V7S 7CFM Single Stage Vacuum Pump This is the BVV™ V7S 7CFM Single Stage Vacuum Pump. Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: Internal Check Valve Oil Mist Filter Cap Larger Oil Reservoir for longer Oil life Lightweight Rubber Feet for noise dampening Reliable, Economical and Efficient. Models BVV4D BVV7S BVV9D Stage 2 1 2 Ultimate Vacuum (Microns) 15 75 15 Refrigerant Classes A1 Non-Toxic, Non Flammable Dimensions (in) 12.4 x 4.8 x 10.16 12.4 x 4.8 x 10.16 15 x 6.3 x 11.22 Weight (lbs) 19.4 16.5 32 Free Air Displacement 4.3 CFM 6.4 CFM 8.5 CFM Motor Size (HP) RPM 1 HP 3440 RPM Oil Capacity 10oz / 300ml 14.5oz / 410ml 24oz / 680ml Voltage 110V 60 Hz Power Cord Hard Wired 3m / 9.8' Power Cord Power Switch Standard On / Off Operating Temperature Range 32F to 125 F (0C to 52C) Gas Ballast Valve Yes No Yes Intake Fittings Stainless Steel Inlet Fitting with 1/4" SAE & 3/8" JIC Male Ports Pump Warranty Information Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$388.23
-
V9D 9CFM Two Stage Vacuum Pump
BVV™ V9D 9CFM Two Stage Vacuum Pump This is the BVV™ V9D 9CFM Two Stage Vacuum Pump. Please Refer to these charts for vacuum specifications at altitude and conversions: Vacuum at Altitude Chart Vacuum Conversion Chart Key Features: Internal Check Valve Oil Mist Filter Cap Larger Oil Reservoir for longer Oil life Lightweight Rubber Feet for noise dampening Reliable, Economical and Efficient. Models BVV4D BVV7S BVV9D Stage 2 1 2 Ultimate Vacuum (Microns) 15 75 15 Refrigerant Classes A1 Non-Toxic, Non Flammable Dimensions (in) 12.4 x 4.8 x 10.16 12.4 x 4.8 x 10.16 15 x 6.3 x 11.22 Weight (lbs) 19.4 16.5 32 Free Air Displacement 4.3 CFM 6.4 CFM 8.5 CFM Motor Size (HP) RPM 1 HP 3440 RPM Oil Capacity 10oz / 300ml 14.5oz / 410ml 24oz / 680ml Voltage 110V 60 Hz Power Cord Hard Wired 3m / 9.8' Power Cord Power Switch Standard On / Off Operating Temperature Range 32F to 125 F (0C to 52C) Gas Ballast Valve Yes No Yes Intake Fittings Stainless Steel Inlet Fitting with 1/4" SAE & 3/8" JIC Male Ports Pump Warranty Information Customers using solvents such as stabilization resins (MinWax™, Gator Venom™ etc.), alcohol and other polar solvents must use the vacuum pumps in conjunction with a cold trap for evacuations in excess of 5 minutes. (Excludes Cactus Juice™) If the consumer is using the pump for prolonged periods of time exceeding 5 minutes we require that a cold trap is used or the pump warranty is void. These stabilization resins have the ability to break down the internal components of the pump that are plastic resulting in a seized motor voiding all warranties. When evacuation exceeds 5 minutes these solvents begin to vaporize and then re-condense in the vacuum pump reservoir. Once enough solvent re-condenses in the pump displacing the oil the plastic internal components may begin to warp, melt or seize. The use of a cold trap will condense the vapors prior to making their way to the vacuum pump preventing pump damage due to excessive use. Furthermore, Minwax Wood Hardener™ is not to be used with any vacuum pumps, EVER. (A seized motor will result within the first use.) To prevent these issues from happening to your process, change the Oil after each vacuum pump use, Even if the use time is only 5min.
$656.46
-
Vacuum Chamber 50 Micron Air Filter
Vacuum Chamber 50 Micron Air Filter This vacuum chamber air filter is designed to be used with Best Value Vacs, SVac, and Glass Vac vacuum chambers. It easily threads into the Female NPT side of the valve manifold and protects the contents inside of the chamber from having dust be sucked back into the chamber when vacuum is released because it will filter the incoming air. Quality replacement parts & fittings for vacuum chambers.
$8.47
-
Vacuum Filter Trap
Vacuum Filter Trap This Vacuum Filter Trap is designed to remove potential contaminants from the vacuum line to prolong the lifetime of your pump. Packed with oil-free, stainless-steel SS304 wool and made with a glass jar, the filter trap may optionally be used as a low-cost cold trap. Welch Inlet / Exhaust Separator 1423B with stainless steel wool inside for even more filtration. We built out two separate fitting configurations for your convenience: just choose from the drop-down menu above! The trap ships default with two 3/8" Barbed fittings, but you may alternatively select our KF25 x 1/4" JIC fittings to receive your vacuum trap specially designed for use with our ovens! Simply clamp the trap directly onto your oven's KF25 vacuum port, then connect a 1/4" hose to your vacuum pump. Specifications: Inlet/Outlet: 3/8" FNPT (ships with adapters selected above) Jar: 230ml Glass -- Welch Inlet / Exhaust Separator 1423B Steel Wool: Oil-free SS304 Maximum Vacuum: <29"Hg Dimensions: 2.8" dia x 4.3" tall Please note this item does not include any vacuum tubing. To order, we recommend the 3/8" Gum Rubber Vacuum Tubing.
$508.23
-
Vacuum Oven Vent Outlet Hole and Cap
Replacement outlet hole and cap for eco and neo oven vacuum release knobs. Note the vent release may require the fitting to be greased to hold vacuum.
$25.41
-
Vacuum Oven Vent Release Stopper
Replacement Cap for eco and neo oven vacuum release knobs. Note the vent release may require the fitting to be greased to hold vacuum.
$13.41
-
Vacuum Pump 1/4" Barb x 1/4" Flare Adapter
Vacuum Pump 1/4" Barb x 1/4" Flare Adapter A Vacuum Pump to Barbed Flare adapter is designed to convert any standard 1/4" Flared vacuum pump to a barbed fitting to be used with flexible 1/4" Tubing for Vacuum. The material is nickel plated brass.
$9.88
-
Vacuum Pump to KF-25 Adapter
Adapts to the 1/4" connections for most vacuum pumps on the market.
$121.41
-
Vacuum Pump Vapor Mist Filter
Vacuum Pump Vapor Mist Filter The BVV™ Mist Filter is our solution to capturing the oil mist exhausting out of vacuum pumps. This filter is filled with a replaceable media and will save you $ over alternative solutions like the Koby filter. The filter media is a granular food grade adsorbent and is designed to adsorb oil specifically. The granular media doesn't restrict flow on your pump, and when it becomes saturated with oil it continues to work. We recommend you change out the media when the filter is 50% soaked with oil. During certain vacuum pressures light vapor mist may momentarily exit the filter. The filters within the housing, do not have an indefinite life. Should they become dirty and clogged over the years, it can be cleaned with degreaser like CitraKlean CK-1QT then left to dry before re-loading. Media Capacity: 185 grams. Media Refill: ULTRA-1000G Media Housing Replacement: CLEAR-210 Pump Fitting Thread BVV V Series (Purple) CPSKADPT M27x1.5 BVV VE Series (Black) MCKADPT M24x1.5 Harvest Right Premier Pump BVVKADPT M30x1.5 Harvest Right Standard BVVKADPT M30x1.5 MasterCool MCKADPT M24x1.5 CPS CPSKADPT M27x1.5 Scientific KF25 Exhaust KF25-04FNPT NA
$148.23
-
Vacuum Trap
Vacuum/Cold Trap - 24/40 Male Joint w/ GL-14 8mm hose barb port. Place the vacuum trap in dry ice or another source of extreme cold for use as a cold trap. Trap is openable to remove trapped condensate. For increased efficiency, tandem multiple traps together inline. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$63.53
-
Valve and Gauge Adapter
This valve and gauge adapter allows the user to thread on a gauge and valve to a system or a solvent tank without the need of Teflon tape. This adapter connects with a 1/4" 37-degree Female JIC connection to a 1/4" 37-degree Male JIC connection.
$141.17
-
Valve Manifold - Cross with Hose Barb
Valve Manifold - Cross with Hose Barb This valve manifold fully made of nickle plated brass includes a nylon lock nut, stainless steel washer, and rubber gasket. It also features 2 1/4 turn valves with a 1/4" FNPT Port and a 1/4" Hose Barb Port and The top of the cross has a 1/4" FNPT threaded port.
$36.71
-
Valve Manifold - Cross with Hose Barb and Vacuum Gauge
Valve Manifold - Cross with Hose Barb and Vacuum Gauge This valve manifold fully made of nickel-plated plated brass includes a nylon lock nut, stainless steel washer, and rubber gasket. It also features 2 1/4 turn valves with a 1/4" FNPT Port and a 1/4" Hose Barb Port and the top of the cross has a glycerin filled vacuum gauge 0-(-30) with a 2-1/2" dial. Specifications: Material: Nickel Plated Brass Connection Type 1: 1/4" SAE Flare Connection Type 2: 1/4" Hose Barb Connection Type 3: 5/16-18 Screw thread Valve Type: 1/4 Turn Includes washer, O-ring, Nylon Locknut, and Vacuum Gauge
$55.06
-
Valved Vacuum Adapter 2.0 - Made in USA
Valved Vacuum Adapter 2.0 This Valved Vacuum Adapter allows the user to isolate the vacuum in a short path distillation system from the cow or receiving flasks of the system to allow the easy swap of the flasks and allows for a full bore vapor flow. These adapters have a 24/40 male joint having a grease-less Viton O-ring seal which reduces the grease mess for each fraction. It also includes GL-14 Cap for venting vacuum and also comes with a PTFE threaded valve with Viton Seals. Sizes: 24/40 Joint - All 3 Joints are 24/40 with GL-14 Cap 34/45 Joint - 2 34/45 Joints and 24/40 lower O-ring Joint with GL-14 Cap *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$564.70
-
Vape Cartridge Packaging (Child Resistant 16 CFR 1700 Compliant)
Vape Cartridge Packaging (Child Resistant 16 CFR 1700 Compliant) **Does not come with a Cartridge. This blank matte black packaging will hold 0.5ml - 1.0ml carts. The carts pictured are the BVV™ ceramic tip carts. The packaging is universal. BVV™ has tested the fitment with dozens of carts and just about every length and barrel fits nice and snug. The packaging is child resistant to the latest standards and is fully recyclable. This attractive box is patented which means your box will stand out among the others. Give your extracts the presentation they deserve by affixing your own label and brand to this executive level box. The insert comes with all boxes but not installed and is pre-creased so it can easily be folded. Packaging Dimensions Measure: 2-1/4" Wide x 4-3/8" Long x 7/8" Tall *Custom Designs for orders over 5,000 pieces, production lead time 3 weeks from proof. BVV™ and their payment vendors retain the right to refuse to accept certain transactions if it conflicts with their Terms of Service. Therefore, certain items on the website may not be able to be purchased using certain payment methods (Ex. Amazon Pay) if it is prohibited in that payment method’s Terms of Service. The available payment methods will display at checkout.
$1.69 - $2.12
-
Variety Pack - Small - 24ct - Rosin Filter Bags
Rosin Filter Bag Variety Pack Improve your yields with our Rosin Bags!- With no bag, product flattens and spreads out as it's squeezed- Our bags will keep your product packed tightly together and provide higher PSI- Our Rosin Filter Bags are made from woven, sewn Nylon: our weave pattern offers superior strength to help prevent blowouts.- Easy use: Simply pick up and toss bag when done. No need to manually separate material and product.- Safe: We use sewn bags, not glued. No messy glue residue to worry about! This is a variety sample pack of our Rosin Filter Bags. Each pack contains a total count of 24 mesh bags, in 8 different sizes:- (3) 25μm mesh bags, 2.5"" x 3.25""- (3) 45μm mesh bags, 2.5"" x 3.25""- (3) 73μm mesh bags, 2.5"" x 3.25""- (3) 90μm mesh bags, 2.5"" x 3.25""- (3) 120μm mesh bags, 2.5"" x 3.25""- (3) 160μm mesh bags, 2.5"" x 3.25""- (3) 190μm mesh bags, 2.5"" x 3.25""- (3) 220μm mesh bags, 2.5"" x 3.25""
$28.23 $14.12
-
Viton O-Ring For 24/40 Ground Joint
Replacement viton (FKM) o-ring for 24/40 ground glass joints with an o-ring style seal
$5.65
-
Viton Piston Cylinder Top O-ring for TRS21 and BVV 2/4CYL
Replacement Viton Piston Cylinder Top O-ring for TRS21 and BVV 2/4CYL sold as single O-ring
$5.65
-
Viton Replacement O-ring for TRS21 and BVV 2/4CYL Suction Valves
Viton Replacement O-rings for TRS21 and BVV 2/4CYL Suction Valves sold as single O-ring.
$2.82
-
Washers For High Pressure Clamps
Washers For High-Pressure Clamps These stainless steel flat washers provides a larger circular bearing surface, which helps prevent a nut or bolt head from pulling through the material.
$1.06
-
Water Circulation Vacuum Pump
Water Circulation Vacuum Pump This Circulation and Vacuum Pump combines the best of both worlds by using the circulating water to pull a vacuum which requires no oil at all and has very low maintenance requirements overall due to this unique process and design. Each vacuum port on the unit pulls vacuum separately from one another so the user can use it for different applications at the same time or combined to increase the vacuum. This pump will also circulate water through the backports as needed to cool and application and dissipate heat as needed. Specifications Vacuum Degree 0.0980Mpa (735 Torr) @ 25°C Single Tap Exhaustion 10L/min Voltage 110V / 50Hz USA Plug Noise <50DB Specifications Number of Vacuum ports: 2qty (independent vacuum po Vacuum Port Size: 3/8" Vacuum Depth: 16 torr Number or Water Circulation inlet: 1qty Number or Water Circulation Outlet: 1qty Pumping Speed: 6.5 L/min Reservoir Capacity: 12L Overall Dimensions: 15.5" x 11.5" x 17" Decibel: 62 dB Weight (no water): 17lbs 10oz
$479.99
-
Welded Coil in Coil
Welded Coil in Coil The Jacketed coil is a 40ft length of 1/2" tube that is completely encapsulated by the 3/4" outer jacket. The inner tube has 1/2" compression fittings and the outer tube has 1/2" FNPT connection ports. The built version comes with USA made SSP instrumentation valves with 1/2" JIC connection for the inner tube and either 1/2" MJIC, 1/2" OR 3/4" hose barb connections for the outer tube. The Coil itself is 10" In diameter and can be mounted successfully utilizing one of our 10" Pipe Hangers
$1,376.45 - $2,110.56
-
WFE Rack 8
Extruded Aluminum Framing Rack This rack is constructed of 1.5" extruded aluminum framing. This framing has slots that can be used for a wide variety of mounting hardware. This large rack is a good size to contain a wiped film or similar distillation equipment, along with three laboratory heaters/chillers stacked on the right side. The rack has six swivel casters for smooth transport with locking wheels in the corners. NOTE: This rack ships unassembled. Allow 6 hours for assembly
$5,505.80
-
White Kitchen Whip Aluminum Dispenser 1 Pint & 1 Liter
Crafted from stunning aluminum, our half-pint and 1 liter cream whipper by BestWhip ensures top-notch quality for those who seek to prepare smaller quantities of whipped cream. Don't be fooled by its size; this compact dispenser is a powerhouse in the kitchen, delivering flawless whipped cream consistently. Professional Grade: Engineered to meet the standards of culinary experts. Elegant Design: The plastic head complements the beautiful aluminum construction, adding an aesthetic appeal to your kitchen tools. Efficient Operation: Utilizing 8gm nitrous oxide chargers, it guarantees a smooth and quick whipping experience. Perfect Capacity: Holds 1 quart of liquid, making it suitable for intimate gatherings or individual servings. Long-lasting Freshness: Store your whipped cream in the refrigerator, and it'll stay fresh and luscious for up to 14 days.
$42.35
-
White Mineral Oil - USP, Food Grade, NSF, Kosher
White Mineral Oil - Grade 7 Food Grade - USP - NSF - Kosher - Halal Made in Canada - High Purity White mineral oil can be used for many applications. Industrial, cosmetics, and food processing. Our Mineral Oil can be used in direct skin and food contact. Our oil is colorless, odorless and tasteless . This mineral oil can act as a non-conductive coolant, thermal fluid, lubricant, release agent, binder, defoamer, protective coating or float, sealing and polishing agent, dust control agent, and more. It has applications in three main areas: The industrial sector Cosmetics Food processing While those three sectors use this element most widely, it has a variety of other applications. White mineral oil is a standard household item, but has also found uses in some niche markets. The substance is versatile and has many properties making it useful in a range of applications. Food Grade Certified to FDA 21 CFR 172.878 Specific gravity @ 25°C 0.842 Kinematic Viscosity @ 40°C, cSt 12.2 Saybolt Viscosity @ 100°F, SUS 70 Colour, Saybolt +30 Pour Point, °C -24°C Flash Point, COC, °C 175°C Flash Point, COC, °F 347°F BVV Mineral Oil 7 White NF - COA BVV Mineral Oil 7 White NF - Spec Sheet BVV Mineral Oil 7 White NF - SDS What is a food grade mineral oil? To use mineral oil in food preparation, it must be classified as a food-grade mineral oil. This is vital for health and safety as well as legal compliance. The Food and Drug Administration (FDA) has established standards any 'food-grade' substance must meet for both direct additions to foods and uses that may result in incidental contact with food. The requirements for purity, amount used, and processes vary based on how one uses mineral oil. The United States Pharmacopoeia (USP) and the National Formulary (NF) first created guidelines for the use of mineral oil in manufacturing. The FDA requires that food-grade mineral oil meet USP XX test requirements for readily carbonizable substances, which USP released in 1980, and USP XVII test requirements for sulfur compounds. It also needs to meet the specifications in Volume 45 of the Journal of the Association of Official Analytical Chemists. Mineral oil used as a lubricant for food-processing machinery must be registered with NSF International, an independent global food safety organization, as lubricants for incidental food contact to be used in food-processing plants under the jurisdiction of the U.S. Department of Agriculture (USDA). Other organizations oversee mineral oil use in other industries. For example, the Association of American Feed Control Officials (AAFCO) governs its use as a dust control agent for animal feeds. This classification is different, however, from food-grade mineral oil. Mineral oil used in the production of pharmaceuticals must be considered pharmaceutical-grade. The cosmetics and medical industry use highly refined mineral oil to avoid irritating the skin, eyes, and other body parts. Mineral oil chemical formula Mineral oils coming from crude petroleum oils vary in their make-up and contain complex structures. They include mixtures of straight and branched-chain paraffinic, naphthenic, and aromatic hydrocarbons. Alkanes, which are acyclic saturated hydrocarbons, are a significant component. They are made up of hydrogen and carbon atoms in a tree structure where all the carbon-to-carbon bonds are single. Mineral oil typically contains between 15 and 40 hydrocarbons. Mineral oil attributes Understanding the physical and chemical properties of mineral oil will help you to determine how best to use it in your industrial, food-processing, or other processes. These attributes may differ depending on the type of mineral used, how you use it, and whether any other substances get added to the oil. Mineral oil is a clear, colorless, and odorless liquid. This lack of strong physical qualities helps make it valuable in a variety of applications. Manufacturers can add it to products without changing their color, scent, flavor, or other crucial aspects. Mineral oil is also generally regarded as safe for human consumption, but in limited amounts. These features enable its use in the food processing and pharmaceutical sectors. Refined mineral oil does not clog pores, which allows for its use in cosmetics. Mineral oil has a density of 0.85 grams per milliliter (g/ml), and its specific gravity is 0.845 - 0.905. Its kinematic viscosity is greater than or equal to 38.1 millimeters squared per second (mm2/s). It is insoluble in water. The substance has an initial boiling point of 424.4 degrees Fahrenheit (°F) and a boiling range that extends up to 1189.4 °F. Its flash point is 275.00 °F closed cup and 380.00 °F open cup. It has an auto-ignition temperature of 500 °F, and its heat of combustion is 31.5 kilojoules per gram (kJ/g). As mentioned above, mineral oil has an NFPA flammability rating of one, a health rating of zero, and a reactivity rating of zero, meaning it is not a high fire risk. One of the most beneficial attributes of white mineral oil is its lubrication capabilities. This is the primary reason it has so many industrial, mechanical, food-processing, and medical applications. This property plays a crucial role in many manufacturing and food production processes. Its ability to transfer heat and its non-conductivity enable mineral oil's use as a coolant in a various electronic and mechanical equipment, as well as in industrial processes. Its resistance to water and other liquids, as well as insolubility in water, allow mineral oil to function as a sealant and binder in a variety of products. Safety Mineral oil is not regarded as an especially dangerous substance, but like all chemicals, users should handle it with appropriate care and precautions. A Material Safety Data Sheets (MSDS) for mineral oil may include the following information: Eyes: Mineral oil may cause eye irritation if it comes into contact with them. Flush eyes for several minutes and seek medical attention. Skin: It may cause skin irritation if prolonged contact with skin occurs. Remove contaminated clothing and wash affected areas or shower. Get medical attention if irritation persists. Inhalation: Inhaling mineral oil mist may irritate the respiratory tract and lungs. If this occurs, move to fresh air. Get medical attention if irritation persists. Ingestion: Ingestion can cause gastrointestinal irritation and result in nausea, vomiting, and diarrhea. If conscious, rinse mouth and drink water. Do not induce vomiting. If irritation persists, get medical attention. Mineral oil is combustible but has a low flammability rating. Having a National Fire Protection Association (NFPA) rating of one, means mineral oil must be preheated to ignite. Mineral oil has an instability rating of zero, which means it is stable even under fire conditions, and a health rating of zero, meaning it does not create any additional hazards beyond normal combustibility. You can extinguish a mineral oil fire using water fog, foam, dry chemical powder, or carbon dioxide (CO2) but should not use a water jet as this can spread the fire.If you encounter a spill of mineral oil, keep unnecessary personnel away, wear protective equipment, and absorb the spill with an absorbent material before cleaning the affected surface to remove any residue. Applications for mineral oil Mineral oil is inert, which makes it easy to use. Both consumers and businesses in a range of industries use mineral oil for a variety of applications. The three sectors named above primarily use mineral oil, but it appears across a wide range of industries and applications. Here are some of the most common uses in the industrial, personal care, and food production sectors. Use in cosmetics You can find mineral oil in many different cosmetics products including baby lotions, ointment, make-up remover, sunscreens, hair conditioner, and even tissues. Mineral oil is an ideal base material for many of these products because it is inert, colorless, and odorless. Mineral oils may appear in cosmetics as liquid oils or solid waxes. Some kinds of mineral oils are comedogenic, meaning they clog pores. Because of this, the mineral oil used in skincare and cosmetic products is noncomedogenic and does not clog pores. In fact, cosmetics companies often describe mineral oil as having moisturizing, protective, and cleansing properties for the skin. Additionally, these oils are used to give cosmetic products film-forming and water-repellent features as well as increased firmness. Use in food processing The food processing and preparation industries frequently use mineral oil. Sometimes, manufacturers add mineral oil directly to food. At other times, mineral oil assists in the production process but is not added to food directly. As mentioned earlier, all mineral oil that may come into contact with food must achieve classification as food-grade, and it must be used in accordance with all relevant laws and regulations. Food producers use mineral oil as a: Binder, release agent, or lubricant in bakery products, dehydrated foods, egg white solids, and in tablets or capsules for adding nutrients, flavoring, spices, or for use as a dietary supplement Release agent, sealing agent, and polishing agent in confectioners Protective coating on raw fruits and vegetables Defoamer in vinegar and beet sugar production Dough divider Dust control agent for grains. Binder, release agent, and lubricant in the manufacturing of yeast Mineral oil plays a role in some of the non-food products used to prepare, serve, and eat food. In these situations, the oil should also be food-grade. When applied to cookware, bakeware, and cooking utensils, mineral oil prevents food from sticking to them. People rub it onto the surface of wooden cutting boards, bowls, and utensils to prevent them from absorbing water, which can damage them. Mineral oil also prevents wood-based cooking tools from absorbing food liquids and odors, which makes cleaning easier. It acts as a lubricant for food processing equipment as well. Industrial, mechanical, and electrical uses Mineral oil serves to assist with various industrial, mechanical, and electrical purposes. It is an effective lubricant for industrial equipment and often functions as a processing aid. It is an element that helps make up various substances used in industrial processes, such as lubricants, greases, dyes, polymers, and surface treatment products. Mineral oil also acts as a thermal fluid or non-conductive coolant in various electric components. In refrigerators and oil-based electric heaters, mineral oil is used as a cooling liquid. In switchgear, it serves as an insulator and a coolant to diffuse switching arcs. In the production of plastics, mineral oil is used to control the melt flow rate of finished polymer and act as a release agent. Automotive equipment frequently uses mineral oil, primarily as a component in hydraulic liquids in automotive suspension, as well as in lubricants in brake fluids and motor oil.
$28.23 - $4,729.34
You have seen 1104 out of 1112 products