Shop Equipment
10L Neocision ETL Lab Certified Rotary Evaporator Turnkey System
10L NEO Rotary Evaporator Turnkey System 10L NEO Rotary Evaporator Turnkey System setup includes all the necessary components to successfully perform solvent recovery via rotary evaporation. A cold trap should always be used inline between your vacuum system and application to protect the pump from volatile vapors. 10-50L NEO and ECO Rotary Evaporator Diagram 10L NEO Rotary Evaporator Turnkey System setup includes: 10L Neocision ETL Lab Certified Rotary Evaporator Polyscience 6160T 1HP Chiller 3/8" Gum Rubber - 100ft 3/8" Silicone Tubing - 25ft Welch BTpro100 Diaphragm Pump Adjustable Stainless Steel Hose Clamps This guide gives basic quick start instructions for rotovaps. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs. Clean and assemble unit. Make sure all pieces are cleaned and sterilized using an alcohol solution. Connect chiller to condenser and set to 0C (32F). Always fill a rotovap condenser from the top down (chiller output to top of condenser, chiller input to bottom of condenser). Connect vacuum pump to cold trap and connect cold trap to vacuum port on rotovap. Turn on heat bath and set to 40C (113F). Once heat bath, chiller and cold trap have reached desired temperatures, turn on rotovap motor and set speed to approximately 100 RPM (does not have to be precise). Keep in mind, higher RPM’s will increase evaporation power but also increase heat load. Start vacuum pump and allow vacuum to pull down for a few minutes before injection. Once vacuum has been pulled to a sufficient level (does not have to be precise but should be below 100 Torr), using the injection valve, very slowly inject approximately 500 mL of solution into evaporating flask and then close the valve. Allow this small amount to begin evaporating. You may see the chiller begin to rise in temperature, this is called “priming” the rotovap. Once the temperature stops rising or all liquid is almost completely evaporated, open the injection valve again very slowly so that a small amount of liquid begins to enter the evaporating flask. Do not close injection valve this time but continue to allow solution to enter the evaporating flask. At this point you must try to match the input speed to the output speed. What this means is that you should be injecting the same amount of liquid into the rotovap that is equal to the amount of liquid dripping from the condenser into the receiving flask. You will know that the input speed and output speed are matched because the chiller will remain at a stable temperature. If the chiller begins to rise, then you are injecting too much liquid. Dial back the valve until the chiller stabilizes. Once everything is stabilized, you may walk away from the rotovap if necessary. Check every so often to make sure temperatures remain stable and evaporation continues efficiently. **Note: All units are inspected for broken glass or parts before unit is shipped. If unit arrives damaged or glass is broken (this does not include minor imperfections or scuffs in glassware), Customer MUST contact BVV™ within 3 days of delivery to file a claim and receive a replacement part. If customer DOES NOT contact BVV™ within 3 days of delivery responsibility for replacement parts falls on the customer and they must pay for replacement pieces.*** ***Note: This item will ship by freight only.*** ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***
$17,663.14 - $21,287.99
The Press Club Premium Parchment
The Press Club Premium Parchment The Press Club premium parchment is made with a special paper blend specifically formulated for pressing. Press Club parchement paper has been lab-tested and proven to not only improve extraction quality but also increase yields. You cannot find this type of parchment paper anywhere else. 5" x 5"(250 Sheets), 10" x 10"(100 Sheets),6" x 12"(100 Sheets), 8"x 16"(100 Sheets), 23' x 15" Roll 250 Sheets 1-Side Coated Silicone 2x Thicker Than Store Bought Parchment To Prevent Tears 100% Food-Grade & FDA Approved Terpene & Heat Resistant (Up To 475°F) Highest Release Coating For Easy Collecting Satisfaction Guarantee & 365-Day Return Policy Made in USA
$35.40 - $42.49
The Press Club 2" x 4" ROSIN BAGS
2" x 4" Rosin Bags The Press Club brings science to the art of rosin pressing. We pride ourselves in making the toughest and strongest rosin bags on the market. After years of research and lab testing, all our rosin bags are now made with our proprietary pink stitch and come with a ZERO BLOWOUT GUARANTEE™. If you ever get one, we'll replace the bag. It's that simple. Available in 5, 10, 15, 25, 37, 50, 75, 90, 120, 160 and 220 micron. 2” x 4” Inch 10-Pack, 20-Pack, Pre-Flipped Inside-Out 100% Food-Grade Nylon Solvent & Boil Resistant High Pressure Resistance (Over 20 Tons) High Heat Resistance (Up To 375° F) Reusable Over 5x (Simply Wash With Alcohol) Covered By The Press Club’s Zero Blowout Guarantee Satisfaction Guarantee & 365-Day Return Policy Made In USA General Micron Guideline: Sift, Kief, Hash (5, 10, 15, 25, 37, 50) | Flower (75, 90, 120, 160, 220)
$18.37 - $28.30
Replacement Viton O-ring for Sintered Filter Plate
This is a replacement Viton O-ring for BVV sintered filter plates.
$4.97 - $32.63
Nitrogen Pressure Filter
Nitrogen Pressure Filter Is vacuum filtration bottlenecking your processing? Filter faster with BVV's Nitrogen assisted pressure filters. Designed for versatility our prebuilt pressure filters come complete with our 1 micron Dutch Weave Sintered disk for ultra-fine filtration. Process continuous or batch-style solutions in half the time compared to most vacuum filtration applications. Specifications 6"x12" or 12"x12" filtration body 1um Dutch Weave Sintered disc Filter Plate Retention Ring Fast Flow Filter paper Included Solvent dispersal plate 2X Borosilicate Sight Glasses 1X 125 PSI ASME Safety Valves 1X -30hg-250PSI Compound Pressure Gauges 1X 1/2" JIC Lid Valve 2X 1/4" JIC Lid Valves 1X JIC Drain Valve (6NPS: 1/4" 12NPS: 1/2" JIC) Maximum Pressure Rating: 125PSI
$1,986.22 - $3,759.62
True Terpenes Limoncello - Infused
True Terpenes Limoncello - Infused All sales are final. Orders can be refunded prior to fulfillment and shipping but once the order has been fulfilled and/or shipped, no refunds will be issued. Due to the hazardous nature of our product, we are unable to accept returns. (Please Note: This product has 1 week lead time) Named after a delicious sweet liquor this lemon forward strain profile will leave you wanting desert. FRAGRANCE: A strong citrus aroma, but notes of mango, pine and pepper blend into the lemony tang to give this profile a unique nose. A high nerolidol level adds to the floral, fruity green tones. EFFECT: Limoncello will help you unwind at the end of the day with a uplifting peace. CERTIFICATES: COA | SDS | FOOD GRADE Storage Requirements Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store below 15℃ (60℉). Improper storage can cause terpenes to degrade. DilutionTerpenes must be diluted prior to use for flavor and effect (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With CareCan cause skin irritation, do not ingest PRIOR to dilution. TRUE GRADE™ It is our promise to you. Our isolated terpenes are triple-distilled making them the cleanest terpenes in the world. Fresh out of the bottle, undiluted, every single one of our products bests the most rigorous consumer safety standards. GMP | ISO-9001:2015 | FSSC 22000 Blended in cGMP facilities adhering to the requirements for a Quality Management System (QMS) specified by ISO 9001:2015 and FSSC 22000 standards. Analyzed Tested and passed True Grade™ safety specifications for residual solvents, pesticides and heavy metals. Stability Tested Rigorously tested with mid-grade distillate against separation, cloudiness and unacceptable levels of color change. We Qualify True Terpenes implements supply-chain control for all raw materials and is proud to provide True Terpenes’ qualification documents such as certificates, licenses and registrations to be qualified as your supplier. Undiluted We do not add PG, VG, PEG, MCT or Vitamin E Acetate to any of our products. Food Grade Manufactured in cGMP facilities using food grade ingredients. UV Protected This product is packaged in a cobalt blue, UV deterrent and food grade bottle with tamper evident seal. Made in the USA Formulated, blended, manufactured and fulfilled in the United States. Refined Isolates This product contains ultra-pure, molecularly-refined terpene isolates. Only the best.
$172.38 - $3,192.13
True Terpenes Banana Runtz
True Terpenes Banana Runtz Fragrance: Sweet Banana Fresh Flowers Effects: Uplifting Creative Banana Runtz, a banana forward twist on the renowned strain out of California, offers big banana flavor with a nod to throwback candy shops. This fresh take on a nostalgic profile is known to elevate moods, and inspire focus. Storage Requirements: Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store in a cool dry place. Improper storage can cause terpenes to degrade. Dilution: Terpene Strain & Flavor-Infused Strain Profiles, Effects-Based Terpene Profiles & Terpene Flavors:The Terpene products above must be diluted prior to use. (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Viscosity Extract Modifier: The Terpene product above must be diluted prior to use. (1-3% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With Care: Can cause skin irritation, do not use PRIOR to dilution. Banana Runtz-Specific Certificates: Product Specification Certificate of Analysis Safety Data Sheet Food Safety Company-Specific Certificates: ISO 9001:2015 GMP Certification FSSC 22000
$172.38 - $3,192.13
True Terpenes Headband
True Terpenes Headband Fragrance: Sweet Earth Fuel Effects: Uplifting Creative Soothing Headband is an earthy, diesel, pungent strain has potent effects that are long-lasting but come on slowly. It is a cross between OG Kush and Sour Diesel. Effects are soothing, euphoric, uplifting, and creative. The name of this strain comes from reported pressure around the crown similar to the feeling of wearing a headband. Storage Requirements: Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store in a cool dry place. Improper storage can cause terpenes to degrade. Dilution: Terpene Strain & Flavor-Infused Strain Profiles, Effects-Based Terpene Profiles & Terpene Flavors:The Terpene products above must be diluted prior to use. (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Viscosity Extract Modifier: The Terpene product above must be diluted prior to use. (1-3% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With Care: Can cause skin irritation, do not use PRIOR to dilution. Headband-Specific Certificates: Product Specification Certificate of Analysis Safety Data Sheet Food Safety Company-Specific Certificates: ISO 9001:2015 GMP Certification FSSC 22000
$172.38 - $3,192.13
50L ECO Receiving Flask
Receiving flask for 50L Best Value Rotary Evaporator. *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$560.40
PolyScience polyclean CLARIFIER - 8 oz
PolyScience polyclean CLARIFIER - 8 oz Description Keeps reservoirs clean and odor-free. Concentrated: 8 oz (237 ml) treats approximately 200 gallons (757 liters). Quantity: 8oz (237 ml) Temperature Range: n/a Part Number: 004-300040 Safety Data Sheet (SDS) For use with: Circulating Baths Refrigerated Circulating Baths Heating Circulating Baths Stainless Steel Open Bath Systems Polycarbonate Open Bath Systems Viscosity Bath Calibration Bath 75L Refrigerated Circulating Bath Coliform Bath General Purpose Water Baths LM Series Benchtop LS Series Benchtop MM Series Benchtop 6000 Series Chiller 3370 Liquid-to-Air Cooler 4100 Liquid-to-Liquid Cooler
$92.22$69.52
10L Neocision Dual Head Short Path Distillation Kit
10L Neocision Dual Head Short Path Distillation Kit This unit carries a 2 day lead time. The 10L Neocision Distillation Turnkey Setup features our Dual 10L P5 Distillation Heads and USA made glass. Every component in this turnkey is made for precision, throughput, and repeatable results. Also included the Bullseye Precision Vacuum Gauge from Digivac which is the most rugged and dependable vacuum gauge on the market. You will also receive a Dual Dewar Style Glass Cold Trap to keep all volatiles and solvents out of your vacuum system. This Turnkey Setup gives you everything needed to perform distillation at the highest level. The 10L Neo Kit Includes: 10L Neocision Kit with Dual P5 Distillation Heads KF-25 90 Degree Long Manifold and Metering Valve Dual Dewar Style Glass Cold Trap Bullseye Precision Vacuum Gauge Distillation Quick Start Guide This guide gives basic quick start instructions for distillation systems. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs, Before beginning distillation, ensure the following steps have been taken: Vacuum Pump is in good working order. Pump should be run against dry load to allow internals to warm up. Oil should be clear. Cloudy or dark oil should be changed. All glass components are in good working order and ready to be assembled A winterization and degassing procedure has been done to prepare oil for distillation Once all three of these steps have been completed, you are ready to begin distilling. Begin by placing stir bar in boiling flask and then load your material. This should be done using a funnel. A small amount of alcohol in the oil will give it a thinner consistency making it easier to transfer. Assemble all glassware and ensure each joint is properly greased. Do not use too much, as the vacuum pressure might pull some grease into the system. To ensure a full seal, spread grease in a circular motion by rotating glassware Attach circulator to condenser and set temperature to 50C. Allow circulator to reach temperature before beginning distillation. Connect vacuum pump to manifold. The manifold will allow you to isolate each individual component as well as let atmosphere into and out of the system. Connect receiving cow to cold trap. Connect cold trap to manifold. Connect vacuum gauge to manifold. At this point, ensure all connections are correct. Also ensure receiving cow is positioned to collect the first fraction in the far-left receiving flask. Circulator should be at its set temperature. Turn on vacuum pump to begin process. Turn on heat and set to 60C. Vacuum pump will begin to pull down and temperature will begin to rise. Watch the gauge to monitor vacuum pressure and stability. Start stir slower and increase speed with temperature. Once you are close to 60C, increase the temperature 20 degrees. Continue to raise the heat incrementally in 20-degree steps, increasing the set temperature as you near your set point. Increase temperatures incrementally until you reach 220C. You will see your first fraction somewhere between 180C and 190C or slightly before. This is the “heads” fraction. You will move to your second fraction when you see an increased reaction in the head, a slight color change toward golden, as well as a thickening of distillate. When this fraction hits, allow the distillate to “self-clean” the head for a minute or two then, rotate the cow to the middle receiving flask. Collect your “main body” fraction. You will see temps between 190-220C during this fraction. Continue to increase stirring speed as necessary. Reaction in the head may vary but it should never stop. As fluid level in the boiling flask decreases, increase stir speed. The final “tails” fraction is a mixture of the first and second fractions and should be saved for re-distillation later. Ideally, you want to turn the cow to the final flask before the tails fraction hits. The “tails” fraction has an obvious color change and will be darker than the “main body” fraction. You will see temps between 200-250C during this fraction. As fluid level in the boiling flask decreases even more, set stirring RPM higher (1000+ RPM). You may need to compensate with a bit more heat to finish of the final fraction as well. Once process is complete, stop heat, stop stir, and stop vacuum. Let atmosphere into the system. Be sure to properly store your distillate as exposure to air and light can cause oxidation. ***Note: This entire setup will ship via motor freight.*** *Notice to Customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. BVV™ is not responsible for the failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail, which can cause bodily harm or damage to the surrounding area.
$13,052.28
Neo Vacuum Oven Valve Knob
Replacement Valve Knob for BVV Neocision Vacuum Ovens.
$21.28
3 Gallon Tall Stainless Steel SIDEMOUNT - POT ONLY
3 Gallon Tall Stainless Steel SIDEMOUNT - POT ONLY ***Note: 'with Hardware' Option only includes the side-mount manifold with gauge pre-installed. (Does Not Include Lid or Gasket) This is a replacement part for the following Vacuum Chambers: Glass Vac 3 Gallon Stainless Steel Vacuum Chamber Dimensions: 11" Tall x 9" Diameter Hole Size: 21/64 Material: 304 Stainless Steel
$92.22
The Press Club 2.5" x 9" ROSIN BAGS
2.5" x 9" Rosin Bags The Press Club brings science to the art of rosin pressing. The Press Club prides themselves in making the toughest and strongest rosin bags on the market. After years of research and lab testing, their rosin bags are now made with their proprietary pink stitch and come with a ZERO BLOWOUT GUARANTEE™. If you ever get one, they will replace the bag. It's that simple. Available in 25, 37, 50, 75, 90, 120, 160 and 220 micron. 2.5” x 9” Inch 25-Pack Pre-Flipped Inside-Out 100% Food-Grade Nylon Solvent & Boil Resistant High Pressure Resistance (Over 20 Tons) High Heat Resistance (Up To 375° F) Reusable Over 5x (Simply Wash With Alcohol) Covered By The Press Club’s Zero Blowout Guarantee Satisfaction Guarantee & 365-Day Return Policy Made In USA General Micron Guideline: Dry Sift & Bubble (5, 10, 15, 25, 37, 50) | Flower (75, 90, 120, 160, 220)
$42.49
HTP Big Daddy Press - 2 Ton
HTP Big Daddy Press - 2 Ton If you are looking for a quality press then the Big Daddy Press is for you! These high quality presses are built from Aircraft Aluminum and stainless steel designed to be used in conjunction with a unique heating process.The Big Daddy Press operates with a 2-Ton Hydraulic cylinder. It has a capacity of 3x3.High Tech Pipes make quality presses that are manufactured in the U.S.A. using American materials and labor. Each Press is assembled and individually inspected before shipping. Our Presses are designed to be heated to the ideal temperature which is an important aspect of the Pressing process. We design and build our products to stand the test of time and to become a permanent piece of equipment for the end user. We use aircraft aluminum which maintains heat as opposed to other Presses on the market which use steel that either quickly loses heat or heats up too fast thus destroying the material that is being pressed. Each Press comes with full step by step instructions and a video is available as well.
$595.79$560.40
Cascade CDO-28 Dry & Decarb Oven
Cascade CDO-28 Dry & Decarb Oven This item carries up to a 2 week lead time. Cascade’s CDO-28 is purpose-built for large-scale, industrial decarboxylation of material with additional features: 28 Cu. Ft. Built-in Humidity Sensor assists in dryness targets Stay in place sliding extension shelves NRTL Certification 6 each FDA & temperature rated fine micron mesh bags for ground material – Mesh bags are required to prevent oven contamination and material loss. This powerful, large capacity forced air laboratory oven uses heated air to remove unwanted compounds from products that are not temperature sensitive. Our ovens feature horizontal airflow that enables more consistent distribution of air. They are designed to have uniform temperatures and airflow across the shelf space from right to left. The CDO-28 includes a built-in humidity sensor and fine micron mesh bags for drying or decarboxylating powders or ground material. Ideal Uses: Industrial scale forced-air convection drying below 149ºC / 300ºF Decarboxylation processes Drying organic material. Drier material will yield better results than processing wet material. Removing as much moisture as possible pre-processing will save time in the post process of vacuum purge and winterization. Lab glassware dryer Model CDO-28 Features Horizontal Airflow. The airflow moves uniformity across the shelf space from right to left Digital set-point control, timer and overtemp failsafe protection Humidity sensor displays relative humidity levels during process Includes 6 sliding, extend and stay in place shelves for ease of loading. Stainless Steel. Includes 6 temp-rated, fine micron mesh bags for easy loading & uniform drying of messy powders, ground up or turbulent materials Fast heat-up: 24 Minutes to 149ºC (300°F) / Uniformity: +/- 2ºC (3.5°F) Stainless steel interior / Food lab grade construction. 301 SST Shelves Triple wall construction meets CE, UL and TUV requirements to keep work-spaces cool. Quality Made in Oregon USA 1 Year Warranty The Cascade Difference Basic forced-air lab ovens are mass-produced and sold by many large scale laboratory equipment distributors. But there are key differences between Cascade and other less costly, often imported lab ovens: Independent Overtemp Failsafe Protection The Cascade Sciences CDO-28 is equipped with a heating cutoff system that will automatically stop power to the heaters when the overtemp setting is tripped. This protection system will provide peace of mind for overnight or unattended drying processing. NRTL Certification. No Extra cost. The CDO-28 Oven comes certified by the Nationally Recognized Test Lab, TUV. This certification is a requirement by many municipalities. CAN/CSA-C22.2 No. 61010-1:2012+UPD No. 1:2015-07 + UPD No. 2:2016-04CAN/CSA-C22.2 No. 61010-2-010:2015UL 61010-1:2012-05UL 61010-2-010:2015EN 61010-1:2010EN 61010-2-010:2014 Rigorous Quality Assurance in an ISO Certified, USA Manufacturing Facility Cascade Sciences manufactures our ovens in Oregon, USA. We are proud of our ISO 9001 Certification/Accreditation. Each oven completes a series of quality assurance procedures before shipment: Electrical & mechanical safety is thoroughly tested in compliance with TUV requirements Functional testing verifies user settable items consistent with most lab protocols/usage models Temperature verification includes calibration & temp chamber uniformity following ASTM standards Units are cleaned and packed in ISTA tested, certified packaging materials Specifications Capacity Volume 28 Cubic Ft. (793 Cubic Liters) Interior 31.5″W x 60.5″H x 26″D 800mm x 1,537mm x 661mm Exterior 43”W x 85.5”H x 34.3”D 1,092mm x 2,171mm x 871mm Temperature Temperature Range 2.2ºC (36°F) above room temp to 148ºC (300°F) Temperature Stability +/- 2ºC (+/-3.5°F) Temp Recovery @ 240°F *Load Dependent* Door Open 30 Seconds: 3 min to stabilize Door Open 60 Seconds: 5 min to stabilize Power 230V – 240V / 1ph / 26AMP Oven Must Be Hardwired By Electrician Oven will also run on 208V BTUs Per Hour at Max Power 18,425 BTUs Air Stats Air Intake Adjustable. Top 2.75” Diameter Air Exhaust Adjustable. Top 2.75” Diameter Linear Shelf Space Airflow 17.1 cubic ft per min Shelving Quantity Included 6 each. Height adjustable. Surface Area 31”W x 23”D (787mm x 584mm) Weight Capacity 75 lbs (34 kg) Mesh Bags Quantity Included Comes with 6 Temp Rated Mesh Bags Dimensions 27.5″W x 21.5″D (699mm x 546mm) Polypropylene (PP) Melt Temperature 161°C (363°F) Softening Point 152°C (305°F) Heat Deflection Temperature 90°C (194°F) Glass Transition Temperature 0°C (32°F) * Mesh bags are REQUIRED to prevent oven contamination and ground material loss. * Polypropylene products produced for some filtration applications are made from resin that complies with FDA regulations for food contact. The regulation compliance is product number dependent / specific. * Impact at cold temperatures is likely to cause strand cracking or breakage Weight Product Weight 565 lbs (256 kg) Shipping Weight 640 lbs (290 kg) Certifications ISO 9001NRTL TUV #U8 170464972 077CAN/CSA-C22.2 No. 61010-1:2012+ UPD No. 1:2015-07 + UPD No. 2:2016-04CAN/CSA-C22.2 No. 61010-2-010:2015UL 61010-1:2012/R:2016-04UL 61010-2-010:2015EN 61010-1:2010EN 61010-2-010:2014 Warranty 1 Year Additional Resources: Download P-Trap Exhaust Tutorial View NRTL Certification
$22,695.37
20 Gallon All-Mesh Bubble Wash Bags
20 Gallon All-Mesh Bubble Wash Bags The Press Club Wash Bags are the last set of bubble wash bags you'll ever own! Made from premium, food-grade material specifically for washing you can stop second guessing whether you have the right or best bags in the industry. All The Press Club bubble wash bags are hand sewn with our proprietary pink stitching, making them 2x stronger than competitors. You can be confident The Press Club bags will perform the same no matter if it's your 1st or 1000th wash. We're so confident our bubble wash bags will stand the test of time, every bag comes with a Lifetime Warranty. If you have any manufacturer issues, they will be more than happy to replace the bag for you! KEY FEATURES Fits All Standard 20 Gallon Buckets Hand Sewn With Our Proprietary Pink Stitch w/ Food-Grade Materials Military-Grade Waterproof & No Flaking Bag Liner Premium Drawstring & Cord Locks To Secure Bags Lifetime Warranty On All Wash Bags Includes Meshed Carrying Case For 2-Way Drying & Storage Made In USA AVAILABLE MICRONS 220 Micron (Work Bag), 190 Micron, 160 Micron, 120 Micron, 90 Micron, 73 Micron, 45 Micron, 25 Micron
$63.77
10 Gallon All-Mesh Bubble Wash Bags
10 Gallon All-Mesh Bubble Wash Bags The Press Club Wash Bags are the last set of bubble wash bags you'll ever own! Made from premium, food-grade material specifically for washing you can stop second guessing whether you have the right or best bags in the industry. All Press Club bubble wash bags are hand sewn with our proprietary pink stitching, making them 2x stronger than competitors. You can be confident The Press Club bags will perform the same no matter if it's your 1st or 1000th wash. The Press Club is so confident their bubble wash bags will stand the test of time, every bag comes with a Lifetime Warranty. If you have any manufacturer issues, they will be more than happy to replace the bag for you! KEY FEATURES Fits All Standard 10 Gallon Buckets Hand Sewn With Our Proprietary Pink Stitch w/ Food-Grade Materials Military-Grade Waterproof & No Flaking Bag Liner Premium Drawstring & Cord Locks To Secure Bags Lifetime Warranty On All Wash Bags Includes Meshed Carrying Case For 2-Way Drying & Storage Made In USA AVAILABLE MICRONS 220 Micron (Work Bag), 190 Micron, 160 Micron, 120 Micron, 90 Micron, 73 Micron, 45 Micron, 25 Micron
$63.77
ChemTek Large Fuge Bags - 50 Pack
ChemTek Large Fuge Bags - 50 Pack Centrifuge bags used for separations. Specifications: Size: 50-Pack Dimensions: H: 7” W: 6.5” Micron Size: 25 Micron Material: Food Grade Nylon
$70.94
ChemTek Small Fuge Bags - 50 Pack
ChemTek Small Fuge Bags - 50 Pack Centrifuge bags used for separations. Specifications: Size: 50-Pack Dimensions: H: 4” W: 2.5” Micron Size: 25 Microns Material: Food Grade Nylon
$39.72
5LB MK-V Bi-Directional Closed Loop Extraction Kit
5LB MK-V Bi-Directional Closed Loop Extraction Kit (System comes with 1 yr. limited warranty) Due to popular demand by customers, we have paired recommended vacuum chamber, vacuum pumps, and complete extraction systems for customers to buy with a discounted price. ***Note: Solvent not included with systems unless ordered separately. Any order with butane WILL NOT SHIP EXPEDITED.*** DISCLAIMER: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in extremely well-ventilated areas. Check with your local fire marshal for guidance when operating indoors The 5lb Bi-Directional closed loop increases efficiency by utilizing both a bottom and top solvent input. By using a bottom flood on the first wash to ensure all material has seen solvent, preventing channeling through the material. Finish the run with a top flood input to ensure all residuals have been washed from the material. Oil bearing solvent is collected in the collection base under the material column. Once collected, solvent is distilled and recovered, leaving the oils in the collection base. This is a passive unit that utilizes pressure differences created by manipulating temperature to move solvent. Extractor Configuration: Explorer: Our standard bi-directional extractor model. Comes with a welded bottom base and standard LP tank. This model provides all the benefits of the Orthrus design without any bells and whistles. The Explorer model is perfect for those looking to get the bi-directional performance but have a budget. Explorer models can be upgraded after purchase. Professional: This model features upgrades to help produce a higher quality extract. Solvent is entered into the system through an injection coil. This coil is chilled with dry ice and alcohol, dropping solvent temperatures to dewax inline. Fats and waxes are not soluble when solvent temperature is subzero, so chilling solvent on input is the simplest way to achieve high clarity extract. The Professional also comes with a removable bottom on the collection base. This makes removal of extract after the run as easy as possible. Elite: The Elite series is our fully upgraded Orthrus model. The elite series adds a level of dependability needed for those seeking to produce the highest quality extracts. It features a larger bore on valves and hoses, all American instrumentation valves by SSP, an AVCO ultra-low temperature inline ball valve, jacketed collection base, and stainless steel LP tank. Full dewaxing is guaranteed by combining both an injection coil and sleeved column. Both units are packed with dry ice, making both solvent and material sub-zero temperatures. The material column is fitted with a nitrogen assist port, which helps ensure no solvent gets stuck with the material. The Elite series boasts increased efficiency on both solvent input and recovery by bumping up all valves and lines to 3/8” JIC. The jacketed collection gives precision during recovery, allowing a heated fluid to be circulated around the base. This method keeps temperature both accurate and consistent. The stainless steel LP tank is able to be opened and cleaned, making solvent contamination a non-issue. *NOTE* This model requires a heater circulator or chiller Explorer Professional Elite BVV 316SS Full Bore Valves Welded Bottom Base V9D 9CFM Two Stage Vacuum Pump 3.2CF NEO Vacuum Oven BVV 316SS Full Bore Valves Splatter Platter Base Injection Coil w/ hose V9D 9CFM Two Stage Vacuum Pump 3.2CF NEO Vacuum Oven SSP Valves Injection Coil Dewaxer AVCO Ball Valve Jacketed Base/Platter 3/8” Valves/Lines SSLP Nitrogen Assist V9D 9CFM Two Stage Vacuum Pump 3.2CF NEO Vacuum Oven Unit Includes: Collection Base 12"x12" Welded Bottom Base Assembled 12" biflow lid (2) Stacked 4"x24" Material columns with reducer & top cap 4" filter plate kit 2" Solvent input manifold 2" Ball Valve #50 LP tank 1/4" 48" High Pressure PTFE Braided SS Hose 1/4" 72" High Pressure PTFE Braided SS Hose 3/8" 72" High Pressure PTFE Braided SS Hose 12" clamps, (4)4" clamps and a (5)2" clamp with gaskets (2)4" Gaskets w/ filter Instruction Manual Specifications: 4"x 48" 304 Stainless Steel Material Tube 5lb (900g) 316 Stainless Steel Fully Encapsulated Miniature Ball Valves System Rated to 150PSI Multiple port connections for _" 316 Stainless JIC 37 Degree 304 Stainless Steel Base Container 12" diameter by 12" tall Tri-Clamps at all interfaces make for a high pressure, easy clean unit. Viton Gaskets are designed for Oil Processing Temp range -40-200F Dimensions (Inches): 25" x 7.5' Diameter overall size Weight: 80 lbs. Operating Temperature Range: -40F to 160F Ultimate Vacuum: as low as 10 Microns Base unit Maximum Capacity: 1275 cubic inches, (2.553 Liters) Construction: All components made of 304 Stainless Steel. Max Vacuum -29.9inHg High Polish Interior *Note: Column capacity may vary depending on the density of packed material and packing density. Capacity is calculated using the industry standard of 4.2g/in3. This is the upper limit for column capacity. Low density, uncut, and/or lightly packed material can reduce capacity by 50%. For best results, we recommend to tightly pack coarse ground material.
$12,280.50 - $17,707.12
Polyscience 7 Liter Refrigerated Circulator, -40°C
Polyscience 7 Liter Refrigerated Circulator, -40°C ***Note: This item has a lead time of 2-3 weeks depending on stock availability.*** Description: -40, 7 L Ref Circulator Controller Type: Advanced Digital Display: 3.75" Touch-Pad LCD Connectivity: Ethernet, USB A & B, RS232/addressable RS485, External Temperature Probe Languages Supported: 4: French, German, Spanish, English Swivel 180 Rotating Controller: Yes Working Temperature Range °C: -40° to 200° Temperature Stability °C: ±0.01° Fluid Optimization/Specific Heat Tuning: Automatic and/or user-adjustable Temperature Calibration Capability: 1- point Working Access (L x W x D) (cm): 15.7 x 14.2 x 12.7 cm Pump Type: Pressure/Suction External Temperature Control Capability: Yes Flammability Class (DIN 12876-1): III (FL) Specifications Working Temperature Range °F -40° to 392° Working Temperature Range °C -40° to 200° Nominal Cooling Capacity @ +20C (W) 360 Reservoir Capacity (gallons) 1.85 Reservoir Capacity (liters) 7 Reservoir/Tank Material Stainless Steel Reservoir Cover Included DuraTop Yes LidDock LidDock Cleanable Air Filter Yes Working Access (L x W x D) (inches) 6.18 x 5.59 x 5 in Working Access (L x W x D) (cm) 15.7 x 14.2 x 12.7 cm Temperature Stability °F ±0.02° Temperature Stability °C ±0.01° Display 3.75" Touch-Pad LCD Display Resolution (Set) 0.01 Display Resolution (Read) 0.01 Pump Type Pressure/Suction Pump Speed Variable Process Connections 1/4" (F) NPT External Temperature Control Capability Yes Flammability Class (DIN 12876-1) III (FL) Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes WhisperCool Environmental Control Technology Yes Cool Command Refrigeration Technology Yes Reservoir Drain Yes Included Software PolyTemp Viewer, USB driver Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 21.3 x 8.7 x 24.3 in Overall Dimensions (L x W x H) (cm) 54.1 x 22.1 x 61.7 cm Refrigerant R404A Environmental Compliance RoHS, WEEE Shipping Weight (pounds) 90.0 Shipping Weight (kilograms) 40.8 60Hz Part Number AD07R-40A11B Maximum Pressure (psi) 4.3 Maximum Pressure (bar) 0.30 Maximum Pressure Flow Rate (gpm) 5.30 Maximum Pressure Flow Rate (l/min) 20.1 Maximum Suction Flow Rate (gpm) 3.9 Maximum Suction Flow Rate (l/min) 14.7 Cooling Capacity @ -20°C (W) 115 Cooling Capacity @ 0°C (W) 250 Cooling Capacity @ +20°C (W) 360 Included Hardware Nylon hose adapters for 3/8", 1/4", and 3/16" Heater Wattage 1100 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/12 Regulatory Approvals ETL
$7,446.89
The Press Club 5 Gallon All-Mesh Bubble Bags BUBBLE BAGS
The Press Club 5 Gallon All-Mesh Bubble Bags BUBBLE BAGS The Press Club Wash Bags are the last set of bubble wash bags you'll ever own! Made from premium, food-grade material specifically for washing you can stop second guessing whether you have the right or best bags in the industry. All our bubble wash bags are hand sewn with our proprietary pink stitching, making them 2x stronger than competitors. You can be confident our bags will perform the same no matter if it's your 1st or 1000th wash. We're so confident our bubble wash bags will stand the test of time, every bag comes with a Lifetime Warranty. If you have any manufacturer issues, we'll be more than happy to replace the bag for you! KEY FEATURES Fits All Standard 5 Gallon Buckets Hand Sewn With Our Proprietary Pink Stitch w/ Food-Grade Materials Military-Grade Waterproof & No Flaking Bag Liner Premium Drawstring & Cord Locks To Secure Bags Lifetime Warranty On All Wash Bags Includes Meshed Carrying Case For 2-Way Drying & Storage Made In USA AVAILABLE MICRONS 220 Micron (Work Bag), 190 Micron, 160 Micron, 120 Micron, 90 Micron, 73 Micron, 45 Micron, 25 Micron
$56.68
Synder NFS Membrane
Synder NFS Membrane With a pore size ranging between 0.1-10nm, Synder Filtration's nanofiltration membranes enable the passage of water and certain salts through the membrane while effectively retaining multivalent ions, low molecular weight molecules, sugars, proteins, and various organic compounds. A result of extensive research and development, Synder's NFS, NFX, NFW, and NFG nanofiltration membrane products have demonstrated exceptional resistance to fouling, a high level of selectivity, and the physical durability necessary for diverse industrial separation processes. Specifically, NFS, NFX, and NFW exhibit outstanding rejection of MgSO4 and lactose, while NFG is designed to partially remove monosaccharides from oligosaccharides. These nanofiltration membranes, as a whole, have the capacity to significantly reduce levels of hardness, nitrates, sulfates, tannins, turbidity, color, total dissolved solids (TDS), and moderate levels of salt from feed water streams. The proven performance of Synder's nanofiltration membranes makes them well-suited for a broad spectrum of industrial applications including the desolvation of ethanol from botanical extract solutions. BVV utilizes 4X NFS 2540 Membranes inside our Nanofiltration Skid to recovery ethanol at 30 Gallons per hour. Specifications Polymer: Proprietary PA TFC Approx. Molecular Weight Cutoff: 100-250 DA Typical Operating Flux 30-40 GFD Average Lactose Rejection: 99.5% Average MgSO4 Rejection: 99.5% Average NaCl Rejection: 50% Maximum Operating Pessure <95F/35C: 600PSI/41.4 Bar Maximum Operating Pressure >95F/35C: 435PSI/30 Bar Maximum Pressure Drop per Element: 15PSI/1.0 Bar Maximum Pressure Drop per hosing: 60PSI/4.1 Bar Maximum continuous Operation Temperature: 122F/50C Maximum CIP Temperature: 104F/40C Maximum Temperature Operating pH Range: 3-9.5 Ambient Temperature Operating pH Range: 3-10.5 Maximum Temperature Cleaning pH Range: 2-11 Ambient Temperature Cleaning pH Range: 2-11
$1,387.51
5L Solvent Pro Rotary Evaporator Main Condenser
5L Solvent Pro Rotary Evaporator Main Condenser 5L Solvent Pro Rotary Evaporator Main Condenser *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$425.62
Solvent Pro Series 60/80 Clamp
Solvent Pro Series 60/80 Clamp This is a replacement clamp for 10, 30, and 50L Solvent Pro Rotary Evaporators. This clamp fits an 60mm(2.36") Inner Diameter and 80mm(3.15") Outer Diameter joint.
$21.28
Solvent Pro Series 18/35 Clamp
Solvent Pro Series 18/35 Clamp This is a replacement clamp for 5, 10, 30, and 50L Solvent Pro Rotary Evaporators. This clamp fits an 18mm(0.71") Inner Diameter and 35mm(1.38") Outer Diameter joint.
$21.28
ChemTek T55 Centrifuge
ChemTek CLT55 Centrifuge CLT55 centrifuges provide excellent performance and easy operation in a compact design that saves valuable time and laboratory space. Specifications: Power Supply: 110V 50/60Hz Max Speed: 4000 RPM Max Capacity:4x750ml Time Setting Range: Speed Accuracy: ± 10r/min Noise: ≤65dB Power Consumption: 900W Net Weight: 170lbs Comes with: (20) 50ml Tubes (4) Regular Mouth Basket (4) Wide Mouth Baskets (4) Regular Mouth Stainless Jar Lid/Band (4) Wide Mouth Stainless Jar Lid/Band (4) Five 50ml Tube Holder Inserts (4) Regular Mouth Jar Spacer Inserts (4) Wide Mouth Jar Spacer Inserts (1) 50-pack 5”x 7” Double Stitched Fuge Bags (1) 50-pack 6.5”x 7” Double Stitched Fuge Bags (1) Terp SqueeGee (1) 100-Pack of Large Diamond Grip Gloves (1) Power converter ChemTek CLT55 Centrifuge User Manual
$8,512.36
6" Sauce Separator
6" Sauce Separator Separate diamonds from sauce at scale with our 6" Sauce separator. Simply load your crystallized extract into the top vessel and place it in a heated oven at 120-140F for 4 hours to sweat the sauce from your crystals. Equipped with a 100-micron Buna-N gasket the 6" Sauce Separator allows for easy separation of crystals from the mother liquor. With a max height of 12.5" and a max diameter of 9", the 6" Sauce Separator easily fits within our standard 1.9 CF vacuum ovens. Specifications 6" Splatter Platter for sauce collection 6" 100 Micron BUNA-N Nitrile gasket 6"X6" Body for Extract loading (-30)-250 PSI Compound Gauge 1/4" JIC Butterfly Valve 1.5" Borosilicate Sight Glasses High-Pressure Clamps Dimensions Max Height: 12.5" Max Diameter: 9"
$638.43
Boss Head - Double Swivel
Boss Head - Double Swivel Made of high strength powder coated alloy and can support up to 16mm rods. The boss head can be adjusted and locked to any angle (360°). It is also designed to carry heavy loads and prevent torque damage. Furthermore, it has three wide pad metal screws to easily secure itself to a clamp and support apparatus. Note:Clamps and rods are NOT included.
$18.44
Julabo Adapter M16x1 f to NPT 1/2″
Julabo Adapter M16x1 f to NPT 1/2″ 2 Adapters M16x1 f. to NPT 1/2″ m.
$239.76
Neocision 20L Chiller (-40c) - ETL Rated
NEOCISION 20L Chiller (-40c) - ETL Rated Product Name Circulating Chiller Model NEO20L-40 Reservoir volume L) 20L Refrigeration performance No-load minimum temperature (℃) A: ﹣ 20℃ ( Customizable: ﹣ 30℃ / C: ﹣ 40℃ Best operating temperature (℃) A: ﹣ 20℃ ~ 20℃B: ﹣ 30℃ ~ 20℃C: ﹣ 40℃ ~ 20℃ Best operating environment (℃) ≤30 Environmental relative humidity (%RH) ≤65 Cooling capacity at -40 ℃ kw 0.7 Refrigerant R404A Electrical performance Cooling unit power (W) 1500 Sensor pt100 Controller, monitor liquid crystal Computer interface R485 optional safety protection Compressor delay protection, machine leakage,over-current, over-voltage protection Power AC230V±10%/60HZ Pump Power (W) 15 Maximum flow (L/min) 10 Maximum lift (m) 2.5 Liquid inlet and outlet pipe diameter (mm) φ18 Whole machinefunction Total Weight (Kg) 105 Tank opening/depth ( mm) φ300mm*300mm Out size (mm) 420*580*790 Adaptation rotary evaporator (volume* number) 10L*2 Note The equipment can be customized to different supply voltage frequency; different flow head external circulation system and external magnetic stirring device. TEMP: Displays the measured temperature value. To set the desired temperature, press the setting key until the TEMP SET value flashes. Press the setting key again to confirm the parameter. SET: Displays the desired temperature value set manually. RUN: Indicates that the chiller is operating. Cooling Indicator: Appears when the chiller is cooling. Circulation Indicator: Appears when the pump is operating. TIME: Displays the set running time; this value countdowns to zero and operation stops. To set a timer, press the setting key. When the TIME value flashes, enter the desired time using they arrow keys. Leave at zero if a timer is not needed. Silence Indicator: Appears when an alarm has been silenced. Alarm Indicator: It will appear when there is an alarm. Settings: Used for manually setting values and parameters. Left Arrow: Shifts to the numbers on the left to set desired value. Down Arrow: One push will decrease 1 digit; A long press will decrease digits faster. Up Arrow: One push will increase 1 digit; A long press will increase digits faster. Cooling Key: Press and hold key for more than 4 seconds to control start/stop the cooling function. Circulation Key: Press to start/stop the circulation function. Note: After all parameters have been input, press the cooling key for four seconds to being operation. Instructions Before Use The unit should be used under the following conditions: Place on a stable, non-combustible flat surface Ambient temperature of 5 ~ 35 ℃ Relative humidity ≤ 85% Atmospheric pressure: (86 ~ 106) KPa Altitude not higher than 2000 meters Power: 5L AC 110V±10%/60HZ, 20L: AC230V±10%/60HZ Keep away from any heat, corrosive gasses, strong vibration and electromagnetic sources. Provide a minimum of 300mm of space for proper ventilation (front and rear) Do not spill liquid anywhere other than the bath. When setting temperatures pay attention to freezing points (ethanol/ethylene glycol). When operating for the first time after replacing the heat transfer fluid there may be air trapped in the circulating pump, follow these instructions to purge: a. Disconnect the outlet line from the application NOTE: Fluid may leak from application, be ready with a bucket or plug the port. Hold the Outlet hose above the top of the bath so fluid does not drain out. b. Place the outlet hose into a clean collection bucket. c. Hold the outlet hose firmly so it does not fall out of the collection bucket d. Wearing safety glasses to shield any splashes, turn on the circulating function. e. After the liquid flow significantly increases, turn off the circulator. f. Reconnect the hoses to your application’s ports.
$6,880.82
HUBER Unistat 825 Dynamic Temperature Control / Circulation Thermostat
HUBER Unistat 825 Dynamic Temperature Control (Please Note: There is a 2 weeks Shipping lead time) Unistat Circulators are an ideal solution for fast and precise thermal control of externally connected applications. These systems offer rapid temperature change and a wide temperature range without having to change fluid. The new Pilot ONE controller features a navigation system with easily remembered icons and menus which are sorted by color to make routine work simpler. An amazing software guides you through your set up ensuring all the necessary settings are correct. General Information & Temperature Controller Unistat 825208V Unistat 825460V Temperature range -85...250 °C -85...250 Temperature stability ±0.01 °C ±0.01 Temperature control TAC, self-optimizing (True Adaptive Control) TAC, self-optimizing (True Adaptive Control) Display resolution 0.01 °C 0.01 °C Alarm message optical, acoustical optical, acoustical Controller Pilot ONE (E-grade "Professional") Pilot ONE (E-grade "Professional") Safety class III / FL III / FL Protection class IP20 IP20 Dimensions (W x D x H) 18.11 x 23.78 x 65.55 inches 18.11 x 23.78 x 57.68 inches Weight 696.78 Lb 487.3 Lb Heating / Cooling Capacity Heating capacity 3 kW 4 kW Cooling machine air-cooled air-cooled Refrigerant 1. stage R507 (1,8 kg) R507 (1,8 kg) Refrigerant 2. stage R23 R23 Circulation Pump Pressure pump max. 10.57 gpm ; 13.05 psi 10.57 gpm ; 13.05 psi Pump connection M30x1,5 AG male M30x1,5 AG male Permissible viscosity 50 mm²/s 50 mm²/s Connections Pt100 connection Pt100 Pt100 Digital interface RS232, Ethernet, USB Device, USB Host RS232, Ethernet, USB Device, USB Host Operating Data Permissible ambient temp. 5 to 40 °C 5 to 40 °C Noise level 64 dB(A) 64 dB(A) Filling volume min. 2.9 Liters / 0.77 gal 2.9 Liters / 0.77 gal Volume of expansion 3.6 Liters / 0.95 gal 3.6 Liters / 0.95 gal Power supply 208V 3~ 60Hz 460V 3~ 60Hz Current max 20 A 14,5 A
$112,575.94 - $123,996.69
Glas-Col K Type Thermocouple
Glas-Col K Type Thermocouple Glas-Col K Type thermocouple is used to measure temperatures from -50°C to 1000°C with a lead length of 72" and probe length of either 12" or 18".
$350.43
So-Low -85°C Ultra-Low Upright Freezer - 25 Cubic Ft.
So-Low -85°C Ultra-Low Upright Freezer - 25 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! So-Low Ultra-Low Upright Freezers are second to none in low temp applications to suit any laboratory or application needs. These Ultra-Low Temp freezers feature digital temperature control with 2 temperature displays. One shows the set temperature and the other shows the actual temperature in the freezer. The So-Low U85-25 features a battery operated alarm system that will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Product Specifications Temperature Control Touch Screen Control Displays set point and chamber temperature Hi/Low Alarm Relay Dry Contacts Power Failure Dry Contacts Battery Back-up Viewable Temperature graph Data logging downloadable via USB or FTP Multi-Level Security VNC Remote Access via PC / smart devices Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing feature. Dimensions: Exterior: 50" x 37" x 79.5" Interior: 34" x 25" x 51.25" Capacity 25 Cubic Ft. / 710 Liters Temperature Range -40°C to -85°C / -40°F to -121°F Shelving 4 Adjustable Shelves (5 Compartments) Inventory Rack Capacity 30 Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Access Port Mounted in left hand side of the cabinet will be a 1/2" porthole leading into the chilling chamber, complete with plugs. Refrigeration System So-Low cascade type. Two hermetic motor compressors. These compressors are the heavy duty industrial type: air cooled. The motors are sealed in oil for life and have thermoguard overload protection. Compressors start in sequence to protect the unit from overloading. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$16,811.91 - $17,017.62
So-Low -80°C Ultra-Low Chest Freezer - 27 Cubic Ft.
So-Low -80°C Ultra-Low Chest Freezer - 27 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! So-Low Ultra-Low Chest Freezers are second to none in low temp applications to suit any laboratory or application needs. These Ultra-Low Temp freezers feature digital temperature control with 2 temperature displays. One shows the set temperature and the other shows the actual temperature in the freezer. The So-Low C80-27 features a battery operated alarm system that will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Product Specifications Temperature Control Digital Control with two temperature displays. One display shows the set temperature, the other shows the actual temperature in the freezer. Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Dimensions: Exterior: 98" x 36" x 43.5" Interior: 67" x 23" x 31.25" Capacity 27 Cubic Ft. / 766 Liters Temperature Range -40°C to -80°C / -40°F to -112°F Shelving N/A Inventory Rack Capacity 48 Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Refrigeration System So-Low cascade type. Two hermetic compressors. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$24,111.26 - $25,742.08
Replacement Touchscreen Oven Gauge
Circular replacement touchscreen for oven gauge.
$42.56
Neoprene Gasket for Cubes
NEOPRENE GASKET FOR CUBES Replacement Neoprene gasket for acrylic vacuum chambers. The existing gasket will have to be completely removed in order to get the new one to seal. It is recommended to use a cleaning solution such as CitraKlean.
$55.33
KPR Fitting Port Reducer
KPR Fitting Port Reducer The KPR Fitting Port Reducer is made out of 316 stainless steel and reduces the port from 1/2"FJIC to a 1/4" MJIC. The connection type is a 37° JIC with a 7/16-20 UNF rated thread. BVV™ KPR Fitting Port Reducer - Data Sheet
$25.54
3 Gallon WIDE Stainless Steel SIDEMOUNT - POT ONLY
3 Gallon WIDE Stainless Steel SIDEMOUNT - POT ONLY ***Note: 'with Hardware' Option only includes the side-mount manifold with gauge pre-installed. (Does Not Include Lid or Gasket) This is a replacement part for the following Vacuum Chambers: Best Value Vacs 3 Gallon Wide Stainless Steel Side Mount Vacuum and Degassing Chamber Glass Vac 3 Gallon Aluminum Vacuum Chamber Dimensions: 9" Tall x 10.75" Diameter Hole Size: 21/64 Material: 304 Stainless Steel
$61.01 - $85.12
Cascade CVO-5 Vacuum Oven
Cascade CVO-5 Vacuum Oven (Oven Only) This item carries up to a 1-2 week lead time. Cascade’s Model CVO-5 offers incredible temperature stability for vacuum drying and purging of pharmaceuticals, botanicals, slurries, or any temperature sensitive material. This vacuum oven liberates solvents, water, and other unwanted compounds. It’s ideal for small batch, R&D and laboratory environments. Processing Temperature Sensitive Material? The CVO-5 comes in both low temp & high temp versions. Be sure to get the low temp CVO-5 version that has excellent temperature uniformity for products such as pharmaceuticals, slurries or any product that can be damaged or destroyed by temperature fluctuations. Low & High Temp Specifications Low Temp Specs Temperature Processing Range 26°F to 250°F (121°C) Temperature Uniformity +/- 1.5°F @ 105°F (40.5°C) Temperature Stability +/- 0.4°F @ 105°F(40.5°C) High Temp Specs Temperature Processing Range Up to 428°F / 220°C Temperature Uniformity +/- 6.5% of setpoint At time of order we will verify the high / low temp version best suited to your requirements. CVO-5 Vacuum Oven Features NRTL Certified by TUV 5 each adjustable shelves Stable temperature control. Digital temperature readout with temp sensor INSIDE the oven Solvent resistant BUNA door gasket Bright LED lights in window for visibility of sensitive material Touchscreen LED Control Panel with adjustable settings Smooth, quarter-turn vacuum and vent valves Energize vacuum pump from control panel Rear KF-25 port allows for rapid MAX EVAP purging or running feedthroughs inside oven for monitoring 120V or 220V power options are available Quality Tempered Rated Glass NGI-US to ANSI Z97.1.2007 156CFR/201 11 SGCC -2577 ½ UA Adjustable leveling feet insure your unit sits solid and level in the workspace The Cascade Difference Vacuum ovens have been around for decades. Basic vacuum ovens are mass-produced and sold by many large laboratory equipment distributors. But there are key differences between Cascade and other less costly, often imported vacuum ovens. Exceptional Temperature Control & Stability The Cascade CVO-5 uses a unique control logic not found in most lab grade vacuum ovens. The temperature probe is INSIDE the oven, which minimizes temperature overshoot and delivers best-in-class temperature stability and uniformity particularly in the low temperature ranges. Accurate, stable temps throughout the CVO-5 eliminate hot and cold spots, making accurate use of every inch of shelf space. Touchscreen LED Smart Controller The CVO-5 controller is a flat panel touch screen with built-in, controls that minimze temperature overshoot. When the oven door is open, the controller will wait and not agressively call for heat to attempt to keep the oven interior stable. When the oven is being vented, the controller will pause as to not over-react and overshoot temperature during this temporary event. Read Temperature in degrees Celcius or Fahrenheit Read Vacuum in Torr or Inches of Mercury Energize Vacuum Pump From Oven Control Panel Turn the vacuum pump off and on from the oven control panel. No more reaching around, behind, beside to turn the vacuum pump off an on. Vacuum pump plugs directly into the back of the oven’s auxillary outlet. Independent Overtemp Failsafe Protection The Cascade Sciences TVO-5 is equipped with a heating cutoff system that will automatically stop power to the heaters when the oven shelf temps exceed 392°F or 200°C. This protection system will provide peace of mind for overnight processing or unattended vacuum bake outs. Log Temperature & Vacuum With Data Port The TVO-5 features a rear mounted data port which outputs a digital log line once per minute. Viewing/logging this data requires terminal emulator software such as the open source (BSD License) emulator Tera Term. NRTL Certification #U8 170464972 077. No Extra cost. The TVO-5 Vacuum Oven comes certified by the Nationally Recognized Test Lab, TUV. This certification is a requirement by many municipalities and is often an extra charge on low cost ovens. CAN/CSA-C22.2 No. 61010-1:2012 +UPD No. 1:2015-07 + UPD No. 2:2016-04 CAN/CSA-C22.2 No. 61010-2-010:2015 UL 61010-1:2012/R:2016-04 UL 61010-2-010:2015 EN 61010-1:2010 EN 61010-2-010:2014 Rigorous Quality Assurance in an ISO Certified, USA Manufacturing Facility Cascade Sciences manufactures our ovens in Oregon, USA. We are proud of our ISO 9001 Certification/Accreditation. Each oven completes a series of quality assurance procedures before shipment. Chambers are vacuum tested after welding for vacuum integrity Electrical & mechanical safety is thoroughly tested in compliance with TUV requirements Functional testing verifies user settable items consistent with most lab protocols/usage models Temperature verification includes calibration & temp chamber uniformity following ASTM standards Units are cleaned and packed in ISTA tested, certified packaging materials Equipped for Inert Gas Backfill. Built-In Safety Relief Introduce inert gasses such as nitrogen, argon, helium, etc. as part of your process via the ¼” rear vent barb. The maximum backfill pressure is 15PSI. In an overpressure situation, a simple, built-in safety relief allows gasses to escape via a spring loaded tempered window. Flexible Pumping / Feedthru Connection Ports The TVO-5 ovens offer two different vacuum oven connection points. The standard connection is a 3/8th dia barb located at the rear of the oven. It is connected to the vacuum valve level on the front control panel. For even faster evaporation, purging or drying consider upgrading to the MAX EVAP connection kit. The MAX EVAP connection kit secures to the oven’s rear 1” dia KF-25 port located on the back center of the chamber. The MAX EVAP connection never reduces flow by continuing with 1” diameter vacuum rated clear lines, a 1” dia KF-25 side mounted vacuum valve and KF-25 fittings and hardware. This KF-25 port can also be used to run temperature feedthrus, or monitoring sensors inside the vacuum chamber during processing. Ergonomically Designed, Easy Quarter-Turn Valves For anyone that has struggled with consistently turning the small, round, low-quality vacuum/vent valves, relief is in sight. You will love our large, quarter-turn vacuum/vent valves. Your wrists will thank you! ANSI Rated Tempered Glass + USA Made Steel Cascade ovens are made in Oregon, USA with high quality materials. Our glass is NGI-USA Tempered and certified to ANSI Z97.1.2007 16CFR / 201 11. Our door handles are rugged brushed steel, not plastic. Our vacuum vessels are constructed with American made steel. We’ve tried lower cost, imported steel. But over time, vacuum chambers made of lesser quality/lower tolerance material cannot withstand the flex and pressure changes of vacuum pumping/venting/purging. This can deteriorate vacuum integrity and the oven will lose its ability to hold vacuum. Model CVO-5 Vacuum Oven Specifications: Capacity Volume 4.5 Cubic Ft. Interior 18”W x 24”D x 18”H 457mm x 609mm x 457mm Exterior 26.5” W x 34.5” D x 32.3”H 673mm x 876mm x 819mm Temperature Range Low-Temp Processing Range 26°F to 250°F (121°C) Temperature Uniformity +/- 1.5°F @ 105°F (40.5°C) Temperature Stability +/- 0.4°F @ 105°F(40.5°C) Heat Up / Stabilization Time to 250°F: 120 minutes (to minimize overshoot) High-Temp Processing Range 428°F / 220°C available Temperature Uniformity +/- 6.5% of setpoint *Note that ambient laboratory conditions can affect temp performance. The TVO-5 (CVO-5) comes in both low temp and high temp versions. The low temp version has excellent temperature uniformity for temperature sensitive material. The higher temp version, 220°C has a uniformity about 6.5% of setpoint. At time of order we will verify the high / low temp version you require. INTERIOR LIGHTING - LED Strips (Rated to 150C) GLASS WINDOW - Tempered NGI-US to ANSI Z97.1.2007 Temperature Controller Touch Screen Accurate Within 1°F Independent Overtemp Failsafe Rear Ports Vacuum 3/8th Barb Vent ¼” Barb Auxiliary KF-25 Port Data: Log temp & vacuum levels INERT GAS INTRODUCTION - Yes. Via ¼” Vent Barb. 15 psi max inlet pressure Power Options 110V – 120V / 1ph / 14A 50/60HzCord IncludedNEMA 5-15 Power Outlet 1105 BTU/hrRating at max power 220V – 240V / 1ph / 7A 50/60HzCord IncludedNEMA 6-15R Power Outlet 1228 BTU/hrRating at max power Included Accessories 5 Shelves 20 Clips 4 Leveling Feet Power Cord Door Gasket 18” x 18” Comes with Solvent Resistant BUNA Standard rated to221°F to 105°C Compatible With:High Temp Silicone rated to 446°F to 230°C Viton rated to 401°F to 205°C Weights & Shipping Weight 360 lbs / 163.3 Kg Shipping Weight: 449 lbs / 207.3 Kg 41”L x 41”W x 45”H Class 85 Certifications ISO 9001 NRTL TUV #U8 170464972 077 CAN/CSA-C22.2 No. 61010-1:2012 + UPD No. 1:2015-07 + UPD No. 2:2016-04 CAN/CSA-C22.2 No. 61010-2-010:2015 UL 61010-1:2012/R:2016-04 UL 61010-2-010:2015 EN 61010-1:2010 EN 61010-2-010:2014 Warrenty 1 Year (gaskets not included) Package Specs CVO-5 Manual CVO-Dimentions CVO-5 Calibration Procedure NRTL Certification Vacuum Pressure Chart
$16,170.64
10L Neocision ETL Lab Certified Rotary Evaporator
10L Neocision ETL Lab Certified Rotary Evaporator The 10L Neocision ETL Lab Certified Rotary Evaporator is a full-scale system meant to fulfill the needs of large volume production and meet the requirements of a certified laboratory with its ETL certification standards. Featuring an electric lift bath and all PTFE valves for extreme chemical resistance, the 10L Neocision gives users the ability to recover large amounts of solvent in a smaller footprint with highly improved functionality. All Neocision rotovaps feature high-efficiency valves and drain ports making it easy to directly inject solution continuously without the need to stop the system or release vacuum to drain. The temperature and rotation speed are easily controlled from a single digital interface. Our rotovaps are a fraction of the price of more costly systems with the same functionality and evaporation efficiency. 10-50L NEO and ECO Rotary Evaporator Diagram Features: ETL Certified for Lab use. Digital temperature and speed control with simple user interface Electric Bath Lift Teflon Coated Bath for corrosion resistance High-efficiency drain port and injection valves Smaller footprint for improved workspace allocation Mobility with locking casters Shorter vapor path for faster evaporation and condensation Direct injection capability for continuous feeding of solution Continuous draining capability without the need to release vacuum or stop the system 1-year warranty on all mechanical parts. Does not include glassware. Specifications: Model 10L Solvent Pro Series Rotary Evaporator Optimum Ambient Temperature 5~25C / 41~105.8F Glass Material GG-17 High Borosilicate Power (V/Hz) 220-240V 60Hz Single Phase Speed Regulation Digital Step-less Regulation Rotation Speed 20-130 RPM Set Temperature RT+5-99C Temperature Control Digital Temperature Control Maximum Vacuum Pressure -29.8 inHg Evaporating Flask Capacity 10L (10000ml) Receiving Flask Capacity 10L (10000ml) Condenser Style Main + Auxiliary Vertical Double Helix Heater Max Current Draw (Amps) 25 Water Bath Material 304 Stainless Steel Water Bath Size 17.7 x 9.8 in. Lifting Function Electric Lifting Stroke 190mm / 7.5 in. Total Power Consumption (kW) 3300w Dimensions 81 x 44 x 20 in. Weight 155 lbs Vacuum Connection 14mm / .55 in. Barb Condenser Connection 18mm / .70 in. Barb Warranty 90 days excluding glass parts Certifications ETL Rotovap Quick Start Guide This guide gives basic quick start instructions for rotovaps. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs. Clean and assemble unit. Make sure all pieces are cleaned and sterilized using an alcohol solution. Connect chiller to condenser and set to 0C (32F). Always fill a rotovap condenser from the top down (chiller output to top of condenser, chiller input to bottom of condenser). Connect vacuum pump to cold trap and connect cold trap to vacuum port on rotovap. Turn on heat bath and set to 40C (113F). Once heat bath, chiller and cold trap have reached desired temperatures, turn on rotovap motor and set speed to approximately 100 RPM (does not have to be precise). Keep in mind, higher RPM’s will increase evaporation power but also increase heat load. Start vacuum pump and allow vacuum to pull down for a few minutes before injection. Once vacuum has been pulled to a sufficient level (does not have to be precise but should be below 100 Torr), using the injection valve, very slowly inject approximately 500 mL of solution into evaporating flask and then close the valve. Allow this small amount to begin evaporating. You may see the chiller begin to rise in temperature, this is called “priming” the rotovap. Once the temperature stops rising or all liquid is almost completely evaporated, open the injection valve again very slowly so that a small amount of liquid begins to enter the evaporating flask. Do not close injection valve this time but continue to allow solution to enter the evaporating flask. At this point you must try to match the input speed to the output speed. What this means is that you should be injecting the same amount of liquid into the rotovap that is equal to the amount of liquid dripping from the condenser into the receiving flask. You will know that the input speed and output speed are matched because the chiller will remain at a stable temperature. If the chiller begins to rise, then you are injecting too much liquid. Dial back the valve until the chiller stabilizes. Once everything is stabilized, you may walk away from the rotovap if necessary. Check every so often to make sure temperatures remain stable and evaporation continues efficiently. ***Note: All units are inspected for broken glass or parts before unit is shipped. If unit arrives damaged or glass is broken (this does not include minor imperfections or scuffs in glassware), Customer MUST contact BVV™ within 3 days of delivery to file a claim and receive a replacement part. If customer DOES NOT contact BVV™ within 3 days of delivery responsibility for replacement parts falls on the customer and they must pay for replacement pieces.*** ***Note: This item will ship by freight only.*** ***Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.***
$6,526.14
12" Collection Base
Pre-Built 12" Collection Base Double your capacity or configure your own custom system with BVV's Pre-Built 12" Collection base. Available in three different variations to suit your application all models of BVV's Pre-Built 12" Collections Base comes standard with high-pressure clamps, borosilicate sight glasses, and full-bore ball valves. Version 1 is the base model equipped with the standard 12" welded base perfect for cost-conscious applications. Version 2 is equipped with a 12"x12" spool & 12" splatter platter to make extract harvesting a breeze, and Version 3 is the top of the line 12" Colleciton base equipped with a 12" jacketed splatter platter for both optimized solvent recovery and ease of harvesting extract. Specifications High Pressure Clamps 2X 2" Borosilicate Sight Glasses 1X 125 PSI ASME Safety Valves 1X -30hg-250PSI Compound Pressure Gauge 1X 1/2" JIC Lid Valve 2X 1/4" JIC Lid Valves Maximum Pressure Rating: 125PSI Variations V1 : 12x12 Base (1200X12B) V2: 12" Splatter Platter base (1200X12S+1200SPL) V3: 12" Jacketed Splatter Platter Base (1200X12S+1200FJS)
$1,300.97 - $1,831.58
HTP Mega T Press
HTP Mega T Press CAPACITY: 3” x 3” x 3” ThickPRESSURE: Manual T-Handle Acme ThreadSHAPE: Cube
$523.51$517.76
BVV 6" Turnkey Falling Film Evaporator
BVV 6" Turnkey Falling Film Evaporator Cutsheet Is your lab floor filled with a fleet of rotary evaporators? Looking to increase solvent recovery throughput? Our new and compact 20GPH Falling Film Evaporator (FFE) has the capability to maximize throughput and replace up to five 50L Rotary Evaporators. The BVV™ 20GPH Falling Film Evaporator is designed to evaporate ethanol that has been diluted in crude oil during a filtration or extraction process. By reducing the vapor pressure inside the system and metering the injection valve, the user can set the heat exchangers to the appropriate temperatures to efficiently evaporate solvent from their crude oil. We paired our FFE with reliable equipment that will keep operations running. End users are required to plumb the process inlet and outlet connections for both heat exchangers. They are supplied with 1.5” sanitary tri-clamp connections. BVV™ can assist with necessary parts needed for a permanent or temporary installation. Temporary installations may be necessary if your lab has limited fume hoods or space which is shared with other processing equipment. Below you will find key features, additional equipment included with the system and the power requirements for each, and real-life efficiencies that were tested. Key Features: · Compact rack design for use in fume hoods (39”x30”x75.5”) · Vernier scale metering valve for controlled injection · Accurate heater and chiller temperature control · Deep vacuum for effective solvent removal · Discharge pumps to eliminate constant reservoir draining and down time · Chemical resistant vacuum pump · Adaptable discharge outlets to customer preference · Insulation to limit thermal loses and reduce condensation (Not Pictured) · Sanitary tri-clamp and compression fittings · Pre-heat injection coil · Injection distribution plate · Tube in shell heat exchanger for efficient evaporation and condensation · Packable vapor path for reduction of contaminants and cleaner separation · Water reservoir for priming the heating system and expansion during operation · The certified model is 22 State certified by PRV Engineers and includes an Infield Verification by PRV Engineers within the purchase price. States include but are not limited to: Alabama, Arizona, Arkansas, California, Colorado, Connecticut, Florida, Illinois, Kansas, Louisiana, Maine, Massachusetts, Missouri, Nevada, North Carolina, Oklahoma, Oregon, Texas, Vermont, Washington, West Virginia, and Wyoming Crude Discharge Pump Easily control discharge speed and collect your extract directly from the 3/8" tube via a collection vessel or swage on a fitting of your preference to pump collected extract to a secondary location. Eliminate constant reservoir draining and operate continuously. Metered Solvent Injection Effectively repeat efficiency and throughput with our vernier scale metering valve. Easy to dial in the desired efficiency and throughput desired by the user. Distribution Plate Directs the injected solvent to be evenly distributed across all tubes in the heat exchanger which maximizes the effective heating surface area. Solvent Discharge and Vacuum Pump The solvent discharge pump eliminates the need for a reservoir and allows you to pump recovered solvent to any desired secondary location. The vacuum pump manifold gives you easy vacuum control during the complete operation. POWER REQUIREMENTS The equipment listed below is included with the system. Check power requirements and amp draw prior to purchasing. Equipment Purpose Power Requirement Amp Draw Notes Hubbell Process Water Heater Heater for Heat Exchanger Column (Evaporation) 240V 3-Phase 87 36kW Heating Capacity Taco ECM High-Efficiency Circulator Water Circulator for Heater 115V 1-Phase 2.5 Max flow rate 52GPM 10hp Polyscience Chiller 230v Chiller for Heat Exchanger Column (Condensation) 230V 3-Phase 78 38.7kW Cooling Capacity 2GPM Ethanol Recovery Pump for Vacuum Pump for Ethanol Recovery Discharge 230V 1-Phase 2.4 2GPM Max Flow Rate, Vacuum Check Valve Beaker and Wrench Explosion Proof Oil Pump Pump for Oil Recovery Discharge 230V 1-Phase 1.1 90L/hr. Max Flow Rate, Vacuum Check Valve Welch BTpro100 Diaphragm Pump Vacuum Pump for System 115 1-Phase 3.4 3.5 CFM, 6 Torr Ultimate Vacuum Total Amp Draw 174.4 EFFICIENCY We are proud to present real data with running parameters and efficiencies that reflect the actual operation of our system. Below you will find the tested throughputs and efficiencies that our FFE is capable of handling. Throughput 11 GPH 18 GPH 20 GPH 22 GPH 24 GPH Efficiency 98% 97% 94% 90% 85% ** Efficiency calculated at 10:1 ratio (Ethanol : Crude Oil) with heater temperature of 160°F. Crude is fully dewaxed when going into the falling film evaporator. Solution starts at room temperature. Speeds may differ based on dilution ratio, crude quality, and running parameters. **
$102,148.30 - $106,688.23
Polyscience 20 Liter General Purpose Water Bath
Polyscience 20 Liter General Purpose Water Bath Key Features: Displays actual and set point temperature simultaneously Three push-button pre-sets for frequently used temperatures Integrated timer Hinged gable cover Calibration capability Reservoir sizes from 2 to 28 liters Reservoir made of 304 Stainless Steel Reservoir drain (10 liter and larger baths) Primary and automatic safety thermostats Also compatible with waterless bath beads Specifications Working Temperature Range °F Ambient +10° to 212° Reservoir Capacity (liters) 20 Reservoir/Tank Material Stainless Steel Reservoir Cover Hinged Gable Working Access (L x W x D) (inches) 9.5 x 17 x 6 Temperature Stability °F ±0.2° Display 3.25" Flammability Class (DIN 12876-1) I (NFL) Over-Temperature Protection / Failsafe Heater Control Yes Maximum Ambient Temperature °F 104° Overall Dimensions (L x W x H) (inches) 17.5 x 22.5 x 15.5 Shipping Weight (pounds) 25.0 60Hz Only Part Number WBE20A11B Included Hardware Sample Tray Heater Wattage 1400 Electrical Requirements (VAC/Hz/Ph/A) 240/50/1/6 Regulatory Approvals ETL Certifications: Regulatory Approvals: ETL Approval CE Approval Operator's Manual
$1,665.58
Polyscience 7 Liter Standard Digital Refrigerated Circulator (-20°C/170°C)
Polyscience 7 Liter Standard Digital Refrigerated Circulator (-20°C/170°C) ***Note: This item has a possible 2-3 week lead time depending on stock availability.*** Specification Description -20, 7 L Ref. Circulator Controller Type Standard Digital Display 3.75" Touch-Pad LCD Connectivity RS232 Swivel 180 Rotating Controller Yes Working Temperature Range °C -20° to 170° Temperature Stability °C ±0.04° Fluid Optimization/Specific Heat Tuning Automatic Temperature Calibration Capability 1-point Working Access (L x W x D) (cm) 15.7 x 14.2 x 12.7 cm Pump Type Pressure Flammability Class (DIN 12876-1) I (NFL) Working Temperature Range °F -4° to 338° Working Temperature Range °C -20° to 170° Nominal Cooling Capacity @ +20C (W) 200 Reservoir Capacity (gallons) 1.85 Reservoir Capacity (liters) 7 Reservoir/Tank Material Stainless Steel Reservoir Cover Included DuraTop Yes LidDock Yes Cleanable Air Filter Yes Reservoir Liquid Level Indicator Yes Working Access (L x W x D) (inches) 6.18 x 5.59 x 5 in Working Access (L x W x D) (cm) 15.7 x 14.2 x 12.7 cm Temperature Stability °F ±0.08° Temperature Stability °C ±0.04° Display 3.75" Touch-Pad LCD Display Resolution (Set) 0.1 Display Resolution (Read) 0.1 Pump Type Pressure Pump Speed Two Process Connections 1/4" (F) NPT Flammability Class (DIN 12876-1) I (NFL) Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes Reservoir Drain Yes Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 21.3 x 8.7 x 24.3 in Overall Dimensions (L x W x H) (cm) 54.1 x 22.1 x 61.7 cm Refrigerant R134a Environmental Compliance RoHS, WEEE Shipping Weight (pounds) 90.0 Shipping Weight (kilograms) 40.8 Catalog Page Number 42-43 60 Hz Only Part Number SD07R-20-A11B Maximum Pressure (psi) 3.5 Maximum Pressure (bar) 0.24 Maximum Pressure Flow Rate (gpm) 2.90 Maximum Pressure Flow Rate (l/min) 11.0 Cooling Capacity @ -20°C (W) 30 Cooling Capacity @ 0°C (W) 120 Cooling Capacity @ +20°C (W) 200 Cooling Capacity @ +100°C (W) 200 Included Hardware Nylon hose adapters for 3/8", 1/4", and 3/16" Heater Wattage 1100 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/12 Regulatory Approvals ETL Key Features: Large, universal icon and English display Swivel 180™ Rotating Controller On-board connectivity: RS-232 serial output On-screen prompts Automatic performance optimization Single-point calibration capability Operator's Manual
$5,618.16
J-KEM® Temperature Controller Model 260/Timer Complete
J-KEM® Temperature Controller Model 260/Timer Complete Designed for processes requiring an extra measure of safety. The Model 260/Timer disconnects outlet power if the process temperature exceeds the set point by a user-specified amount, or following recovery from a power failure. Power remains off until the controller is manually reset. Over temperature is signaled by both an indicator lamp and an audible alarm. Contains a 100-hour digital timer to turn heating OFF (or ON) when the time expires. The Model 260 has two power outlets (1800 watts) for large equipment or heating mantles up to 22L. Contains J-KEM’s patented power control computer which provides 0.1° regulation of anything. SPECIFICATIONS: Power: 15 amps @ 120 VAC, 1800 Watts Weight: 6 Lbs Dimensions: 9.25 × 7.75 × 3.5 in .
$1,837.25 - $2,078.43
You have seen 576 out of 910 products