Drying & Purging
High Pressure Wood Stabilizing Chamber
High Pressure Wood Stabilizing Chamber A BVV EXCLUSIVE! This is our high pressure wood stabilizing column that can perform rapid wood stabilization @ 1600 PSI (1.5" Diameter Tube) & 450 PSI (3"/ 6" Diameter Tube). This extreme pressure makes the toughest woods easy to impregnate with wood stabilizer in as little as 15min. Then its off to the oven for a quick cure and its finished. The blanks in the photo, all 3 were stabilized and cured in less than 1 hour and 15 min, including cleanup. The system is simple. Load your blanks into the column and fill no more than 75% with resin. (make sure the blanks are submerged) Then close the system and turn on the pump set to desired psi. High Pressure Wood Stabilizing Manual with Assembly The compressor you will need can be ordered from this site (GX Pumps Click This Link). BVV does not yet carry the compressor for this system. But our hose will connect directly to the compressor. If the compressor is out of your reach a high pressure hand pump can be used. (GX Hand Pumps Click This Link) The system comes with an installed safety pressure relief burst disk rated for 1800 PSI. (1.5" Diameter tubes) & 450 PSI. (3"/ 6" Diameter tube) Should you exceed the pressure of the system the disk will rupture releasing pressure. What's Included Wood stabilizing manual *Coming soon for 3"/ 6" Diameter. Braided stainless steel hose 2500 psi rated. Main column, stand and top cap valve manifold assembled. Extra safety burst disk, for 1.5" Diameter Tube. 3"/ 6" Tubes self reset. BVV warranties the main column to be free from any defects for 1 year. All other individual components may hold separate warranty periods. BVV does not warranty any claims where resin has been released/backflowed into the manifold hose or valve. Resin is water washable and should be cleaned after each use, especially if resin has accidentally backflowed into the manifold area.
$360.94 - $1,027.62
Inline Candy Desiccant Dryer
The inline candy desiccant dryer is a necessary accessory to any one using a vacuum oven for candy drying. The column will need to be filled by the user with silica gel and has fine mesh stainless filters on each end to hold in the beads. We recommend connecting the vacuum inlet from the pump to the top of the column to prevent any water accumulation in the beads from reaching the pump via gravity. The bottom of the column will connect to the oven itself. The column holds 1.5lb of silica gel desiccant. Its water holding capacity is 36%. Since 1lb of candy can hold as much as 40-60g of water, a 1lb column of desiccant will have the capacity to handle approximately 4.5-5lb of fresh candy drying before it needs to be reactivated. Silica gel can be reactivated by placing in an oven on a sheet pan for 0.5-2.0 hours at 200-250F or microwave for 10 minutes on defrost. BVV Hook Up Guide - Quick Assembly PDF Size Variants Standard Size 2" Outside Diameter x 24" Tall Column (Holds 1.5lbs Silica) XL Size Column 3" Outside Diameter x 36" Tall Column (Hold 6.5lbs Silica) Extension Kit for the Standard Column 2" Outside Diameter x 24" Tall (Holds1.5lbs Silica) *Silica Gel: Source from amazon (USE Clear silica gel) https://www.amazon.com/Dry-Quart-White-Silica-Desiccant/dp/B014VM4AZI/ref=sr_1_3?crid=N1FARCPRUFPT&keywords=silica+gel+clear&qid=1678139406&sprefix=silica+gel+cle%2Caps%2C100&sr=8-3
$41.76 - $552.02
J-KEM DVR-200-EV Digital Vacuum Regulator
J-KEM DVR-200-EV Digital Vacuum Regulator The DVR-200-EV has the same stainless steel pressure transducer inside, but the vacuum valve is outside of the controller. The value of this design is that the vacuum valve can be cleaned or replaced much easier than the valve in the classic DVR-200. Some applications, like distillations or stripping large volumes of solvent, can leave residues inside the valve which causes it to fail. Replacing the vacuum valve is the most frequent repair that J-KEM performs on the DVR-200. Replacing the valve in the classic DVR-200 is difficult and must be returned to J-KEM for repair. With the EV version, the user can disassembled the valve and wash it out, or even replace it in under 5 minutes. For large distillations or botanical applications, J-KEM recommends the DVR-200-EV. No Mercury 100% digital pressure entry and control Wetted parts are 100% stainless steel and Teflon Vacuum ramping feature eliminates bumping Resists: All organic solvents Acids Bases Water Specifications: 100 watts. Vacuum fittings: 1/8″ NPTM. Warranty: Electronics 2 Years, Vacuum Valve 6 months (void if damaged by chemical buildup)
$2,356.72
Neocision Vacuum Oven Shelves
Neocision Vacuum Oven Shelves These are stainless steel oven shelves for our Neocision Vacuum Ovens and fit either a 0.9CF or a 1.9CF Neocision Oven. Specifications: 0.9CF - 11" (279mm) x 11.2" (285mm) x 1/8" Thickness 1.9CF - 14" (356mm) x 15.75" (400mm) x 1/8" Thickness
$49.54 - $63.70
Valve Manifold - Cross with Hose Barb and Vacuum Gauge
Valve Manifold - Cross with Hose Barb and Vacuum Gauge This valve manifold fully made of nickel-plated plated brass includes a nylon lock nut, stainless steel washer, and rubber gasket. It also features 2 1/4 turn valves with a 1/4" FNPT Port and a 1/4" Hose Barb Port and the top of the cross has a glycerin filled vacuum gauge 0-(-30) with a 2-1/2" dial. Specifications: Material: Nickel Plated Brass Connection Type 1: 1/4" SAE Flare Connection Type 2: 1/4" Hose Barb Connection Type 3: 5/16-18 Screw thread Valve Type: 1/4 Turn Includes washer, O-ring, Nylon Locknut, and Vacuum Gauge
$48.13
J-KEM DVM-100
J-kem DVM-100 The DVM-100 continuously displays the pressure in a connected piece of equipment on a large digital display. The vapor path of the DVM-100 is 100% stainles steel to provide long life and chemical compatibility. Comes with J-KEM’s KEM-Net software to provide data logging and a real time graphical display of system pressure. The DVM-100 provides vacuum monitoring but not vacuum regulation.
$1,868.39
DigiVac SNAP Vacuum Controller | Simple, Nimble, Automatic Process Control | Up to 8 Recipes
DigiVac SNAP Vacuum Controller | Simple, Nimble, Automatic Process Control | Up to 8 Recipes Description SNAP Vacuum Controller | Simple, Nimble, Automatic Process Controller with up to 8 Recipes SNAP: Automatic Vacuum Process Controller | Vacuum control and venting with the touch of a button or twist of a dial Vent your vacuum chamber or equalize your system with the touch of a button instead of pulling hoses or turning valves Treat material in chamber more gently by implementing kinder ramp rate controls which is ideal for freeze drying, vacuum drying or lyophilization applications Vacuum Controller with onboard ramp rate recipe control. Set up to 8 recipes based on time and pressure setpoints. Dashboard pushbutton control for START, STOP functionality for each channel allows you to automatically vent or isolate your system with a push of a button Ideal for automating and simplifying vacuum chamber pressure control. SIMPLE – SIMPLIFY YOUR LAB & CONTROL MORE WITH LESS Applications: vacuum chamber (from 1 liter to 1000 liters) research, vacuum ovens/vacuum drying, vacuum furnaces, large scale food processing, microwave drying, composites, rotary evaporators, falling film systems Fine control of target vacuum pressure for more precise processing and research Enables using reliable and long lasting rotary vane pumps & dry scroll pumps in applications where diaphragmpumps were previously required Keeps vacuum pumps near their base pressure resulting in greater longevity NIMBLE – MAXIMIZES THROUGHPUT & PUMPDOWN SPEED Largest flow paths available to insure maximum flow for faster evaporation Maximize throughput and pump down speed with a 20 mm vacuum path (almost full KF25 orifice) AUTOMATIC PROCESS – PRECISION CONTROL & INTUITIVE DESIGN Automatic Vacuum Process Controller | precise automated control with programmable recipes and graphing of vacuum levels Innovative valve control performs both proportional throttle and bleed vacuum control (vent to atmosphere) The integrated bleed design allows you to quickly vent to atmosphere to stop bumping during processing Numerical readings right on the LCD screen and one touch buttons: VENT, CLOSE (isolate, close all valves) and FULL VAC (fully opens the valve for vacuum pump and closes the vent valve) SNAP Vacuum Controller Wetted Material Options Aluminum (6061) wetted surfaces Stainless steel (304) wetted surfaces Measurement and Control Range: 1 Torr to 775 Torr (standard) Need millitorr range?: SNAP has a RJ45 Port for adding an additional sensor to extend the measurement range. We recommend the addition of the DCP Quantum to be able to monitor and control from 0.01 Torr to 1000 Torr. DigiVac SNAP Data Sheet DigiVac SNAP Operational Manual DigiVac SNAP Quick Start Guide
$7,218.78$6,581.83
Cascade Vacuum Oven Door Gaskets
Cascade Vacuum Oven Door Gaskets Gaskets wear out. Remember to clean, rotate and have spares on hand! Our versatile collection of vacuum oven door gaskets is designed to fit the Cascade Sciences CVO-2 , CVO-5, and CVO-10 vacuum oven models, meeting your specific needs. Choose from our Solvent Resistant, VITON, and High Temp Silicone Door Gaskets, each offering superior performance! Features Viton Door Gaskets Available in sizes: 12″ x 12″ (CVO-2) and 18″ X 18″ (CVO-5) Material: VITON (FKM synthetic rubber and fluoropolymer elastomer) Max Temperature: 150°C / 302°F Ideal for Cascade 2 and 5cubic foot vacuum ovens Excellent resistance to solvents, oils, fuels, and mineral acids Low outgassing rate: 1 x 10-6 Torr-liter/cm2-s initial degassing rate Minimal weight loss of 0.07% after over 336 hours of vacuum exposure Exceptional UV resistance, protection against fungus, molds, and oxidation *The name VITON is a registered trademark of The Chemours Company Solvent Resistant Gaskets Available in sizes: 12″ x 12″ (CVO-2) and 18″ X 18″ (CVO-5) Material: BUNA (a material designed to withstand solvents) Max Temperature: 105°C / 221°F Ideal for Cascade 2 and 5 cubic foot vacuum ovens Application: Solvents Excellent resistance to many hydrocarbons, fats, oils, greases, hydraulic fluids, and chemicals High-Temp Silicone Door Gaskets Available in sizes: 12″ x 12″ (CVO-2), 18″ X 18″ (CVO-5), and 24″ X 28″ (CVO-10) Material: Silicone Max Temperature: 230°C / 446°F Ideal for Cascade 2 and 5 cubic foot vacuum ovens Application: General and High Temperature Resists moderate or oxidizing chemicals, ozone, and concentrated sodium hydroxide Specifications Viton Door Gaskets Available in sizes: 12″ x 12″ (CVO-2) and 18″ X 18″ (CVO-5) Color: Black Material: VITON (FKM synthetic rubber and fluoropolymer elastomer) Max Temperature: 150°C / 302°F Solvent Resistant Gaskets Available in sizes: 12″ x 12″ (CVO-2) and 18″ X 18″ (CVO-5) Color: Black Material: BUNA (a material designed to withstand solvents) Max Temperature: 105°C / 221°F High-Temp Silicone Door Gaskets Available in sizes: 12″ x 12″ (CVO-2), 18″ X 18″ (CVO-5), and 24″ x 28″ (CVO-10) Color: Orange Material: Silicone Max Temperature: 230°C / 446°F PRO TIP: Rotate your vacuum oven door gaskets for even wear and longer life.
$498.24 - $1,663.15
Bullseye Precision Gauge with Agilent 536 KF25, NPT or KF16 Sensor | Vacuum Gauge for Processing
Bullseye Precision Gauge with Agilent 536 KF25, NPT or KF16 Sensor | Vacuum Gauge for Processing A rugged portable vacuum gauge for processing applications that pairs unparalleled vacuum measurement with the Agilent 536 sensor that has an integrated baffle which provides protection and helps reduce risk of sensor failure Numeric & Graphical Displays See vacuum readings in either numbers or easy-to-read graphs Has 12 measurement units for implementation in almost any vacuum application Torr, mbar, bar, kPa, inches of Hg, mm Hg, millitorr, microns, inches of water, PSI, Pa Calibrated & Precise Delivered pre-calibrated with Agilent/ Varian 536 thermocouple sensor under actual vacuum against the NIST standard. Note: NIST certification sent with the gauge is an available option here The 536 all stainless steel sensor with baffle has extended sensor life in the presence of condensable gases and improved performance at higher pressures Vacuum Interface: KF25 or NPT or KF16 Wetted materials: 304L Stainless steel, glass, Type P thermocouple Extended Battery Lifespan Portable | Solid state electronics built into a handheld gauge that operates using AA batteries that lasts up to 70 hours In-lab use | Power gauge using the integrated Micro-USB port for long-term use without the need to change batteries Ideal Vacuum Gauge for Processing Applications Laboratory, freeze drying, low pressure distillations, foreline monitoring, Schlenk lines performance, and transformer dry-out Or any application with higher levels of condensables where sensor failure is more likely Units Torr, mbar, kPa, millitorr, microns, Torr, mbar, bar, kPa, inches of Hg, mm Hg, millitorr, microns, inches of water, PSI, Pa 1E-4 – 1000 Torr Range with Accuracy .001 – 5 Torr Sensor Type Agilent 536-KF25 Dimensions 11 x 10 x 4 in Certifications CE, RoHS
$898.81 - $924.29
Bullseye Precision Gauge with Bluetooth | Wireless Vacuum Gauge NPT, KF25
Bullseye Precision Gauge with Bluetooth | Wireless Vacuum Gauge NPT, KF25 The DigiVac Bullseye Precision Gauge with Bluetooth is the world’s first wireless vacuum gauge featuring one-of-a-kind patented vacuum graphing and DigiVac’s ‘Vacuum Gauge’ app Versatile wireless vacuum gauge that you can monitor right from your phone or tablet (Apple ios and android) Enables remote monitoring and troubleshooting Set low and high alarm from your phone Email vacuum data to document leaks, baseline pressure or pump-downs Use battery power or standard microB-USB power Choose standard Thermocouple Plus sensor or the Upgraded Agilent 531 NPT sensor (this sensor configuration is CE and RoHs compliant), or the Agilent 536 NPT sensor which includes an integrated baffle to extend the life of the sensor by helping to protect it from contamination Portable and Precise Rugged thermocouple vacuum gauge ideal for understanding: Leaks, Pump Downs, Out-gassing or Stable Systems Includes a powerful magnet and kickstand to enable hands-free operation Long battery life and versatility with 12 different measuring units (micron, Torr, Inches of Hg, kPa, Inches of H20, millitorr, mbar, Pa, PSIA, mm of Hg, bar, and mm of H2O) Calibrated under actual vacuum against a NIST standard. Graphing and Analysis Patented vacuum graphing displays vacuum and time data Visual graphing right on the display that identifies current system status Vacuum Analytics to quickly identify vacuum pressure trends Graphical display for quick determination of vacuum level Bluetooth Bullseye Gauge Applications Vacuum pump testing Baseline vacuum pump performance Transformer dry-out Schlenk line monitoring Botanical oil processing Distillations Vacuum Process Monitoring Technical Specifications Units Torr, mbar, bar, kPa, inHg, mm Hg, millitorr, microns, inches of water, PSI, Pa Control Range 1E-4 – 1000 Torr Range with Accuracy .001-5 Torr Sensor Type Agilent 531 (NPT), Agilent 536 (NPT, KF15, or KF16), VGT500 Dimensions 6.2”H x 3.7”W x 1.3”D Certifications ROHS and CE
$1,040.35 - $1,196.93
Sheldon Manufacturing - ECONOMY VACUUM OVEN, 0.6 CUFT, NON CE
Sheldon Manufacturing - ECONOMY VACUUM OVEN, 0.6 CUFT, NON CE HEL LAB vacuum ovens provide exceptional capabilities for fast and gentle drying of heat-sensitive materials. They prevent residue accumulation on products and allow safe drying of materials at lower temperatures than typically required when using convection ovens. These units feature a radiant heating system that optimizes chamber space and provides excellent heat transfer and temperature uniformity. All SHEL LAB vacuum ovens are built with stainless steel chambers that are easy to clean and have exceptional durability. The doors on these units have positive latch handles with spring-loaded glass to facilitate a good vacuum seal without hinge binds that shorten the gasket life. The tempered glass viewing window allows for safe, continuous monitoring of samples. A selection of gaskets (for specific applications) and a small benchtop footprint increase the versatility of these ovens. The SHEL LAB economy series of vacuum ovens are outstanding in any application. Features include: Analog Temperature Control Stainless-Steel Interior Built-in Overtemperature Protection 24 Month Limited Warranty
$2,986.60 - $3,269.68
Sheldon Manufacturing - ECONOMY VACUUM OVEN, 1.7 CUFT, NON CE
Sheldon Manufacturing - ECONOMY VACUUM OVEN, 1.7 CUFT, NON CE SHEL LAB vacuum ovens provide exceptional capabilities for fast and gentle drying of heat-sensitive materials. They prevent residue accumulation on products and allow safe drying of materials at lower temperatures than typically required when using convection ovens. These units feature a radiant heating system that optimizes chamber space and provides excellent heat transfer and temperature uniformity. All SHEL LAB vacuum ovens are built with stainless steel chambers that are easy to clean and have exceptional durability. The doors on these units have positive latch handles with spring-loaded glass to facilitate a good vacuum seal without hinge binds that shorten the gasket life. The tempered glass viewing window allows for safe, continuous monitoring of samples. A selection of gaskets (for specific applications) and a small benchtop footprint increase the versatility of these ovens. The SHEL LAB economy series of vacuum ovens are outstanding in any application. Features include: Analog Temperature Control Stainless-Steel Interior Built-in Overtemperature Protection 24 Month Limited Warranty
$3,750.94 - $4,104.80
Sheldon Manufacturing - VACUUM OVEN, 0.6 CUBIC FEET
Sheldon Manufacturing - VACUUM OVEN, 0.6 CUBIC FEET Our revamped SHEL LAB SVAC vacuum ovens provide exceptional capabilities for fast and gentle drying of heat-sensitive materials. Vacuum ovens prevent residue accumulation on products and use lower temperatures than typical convection ovens. Your products are processed with minimal impact and maximum throughput. SHEL LAB vacuum ovens have stainless steel interiors and provide exceptional durability and stability. Available in 4 sizes, SVAC Vacuum Ovens support a diverse array of applications. To achieve required vacuum levels, users can choose from a 3/8-inch orifice or a KF-25 fitting to withstand heavy use and minimize draw-down time. The doors on these units have positive latch handles with spring-loaded glass to facilitate a good vacuum seal without hinge binds that shorten the gasket life. The tempered glass viewing window allows for safe, continuous monitoring of samples. SHEL LAB Vacuum Ovens are equipped with silicone gaskets. Features include: Watlow PM9 Plus Controller Generous Usable Shelf Area Achieve Impressive Vacuum Levels Sizes Range from 0.6 – 4.5 Cubic Feet Built-in Overtemperature Protection 24 Month Limited Warranty Extended Warranties Available (Ask Your SHEL LAB Sales Rep) Please note that this vacuum oven does not include a pump or related accessories. Contact your SHEL LAB distributor for assistance with choosing the ideal pump and accessories for any application.
$7,360.33 - $7,997.28
Sheldon Manufacturing - VACUUM OVEN, 1.67 CUBIC FEET
Sheldon Manufacturing - VACUUM OVEN, 1.67 CUBIC FEET Our revamped SHEL LAB SVAC vacuum ovens provide exceptional capabilities for fast and gentle drying of heat-sensitive materials. Vacuum ovens prevent residue accumulation on products and use lower temperatures than typical convection ovens. Your products are processed with minimal impact and maximum throughput. SHEL LAB vacuum ovens have stainless steel interiors and provide exceptional durability and stability. Available in 4 sizes, SVAC Vacuum Ovens support a diverse array of applications.To achieve required vacuum levels, users can choose from a 3/8-inch orifice or a KF-25 fitting to withstand heavy use and minimize draw-down time. The doors on these units have positive latch handles with spring-loaded glass to facilitate a good vacuum seal without hinge binds that shorten the gasket life. The tempered glass viewing window allows for safe, continuous monitoring of samples. SHEL LAB Vacuum Ovens are equipped with silicone gaskets. Features include: Watlow PM9 Plus Controller Generous Usable Shelf Area Achieve Impressive Vacuum Levels Sizes Range from 0.6 – 4.5 Cubic Feet Built-in Overtemperature Protection 24 Month Limited Warranty Extended Warranties Available (Ask Your SHEL LAB Sales Rep) Please note that this vacuum oven does not include a pump or related accessories. Contact your SHEL LAB distributor for assistance with choosing the ideal pump and accessories for any application.
$9,200.41 - $10,120.45
Sheldon Manufacturing - VACUUM OVEN, 4.5 CUFT
Sheldon Manufacturing - VACUUM OVEN, 4.5 CUFT Our revamped SHEL LAB SVAC vacuum ovens provide exceptional capabilities for fast and gentle drying of heat-sensitive materials. Vacuum ovens prevent residue accumulation on products and use lower temperatures than typical convection ovens. Your products are processed with minimal impact and maximum throughput. SHEL LAB vacuum ovens have stainless steel interiors and provide exceptional durability and stability. Available in 4 sizes, SVAC Vacuum Ovens support a diverse array of applications. To achieve required vacuum levels, users can choose from a 3/8-inch orifice or a KF-25 fitting to withstand heavy use and minimize draw-down time. The doors on these units have positive latch handles with spring-loaded glass to facilitate a good vacuum seal without hinge binds that shorten the gasket life. The tempered glass viewing window allows for safe, continuous monitoring of samples. SHEL LAB Vacuum Ovens are equipped with silicone gaskets. Features include: Watlow PM9 Plus Controller Generous Usable Shelf Area Achieve Impressive Vacuum Levels Sizes Range from 0.6 – 4.5 Cubic Feet Built-in Overtemperature Protection 24 Month Limited Warranty Extended Warranties Available* (Ask Your SHEL LAB Sales Rep) Please note that this vacuum oven does not include a pump or related accessories. Contact your SHEL LAB distributor for assistance with choosing the ideal pump and accessories for any application.
$18,046.96 - $19,780.89
Sheldon Manufacturing - VAC OVEN, 9.3 CUFT, 230V
Sheldon Manufacturing - VAC OVEN, 9.3 CUFT, 230V The SHEL LAB Model SVAC9-2 is one of the largest vacuum ovens on the market, with 9.3 cubic feet of capacity. This unit also features a fully programmable Watlow PM9 Plus controller and a cool touch surface. A digital vacuum gauge shows chamber vacuum level in measurements of Torr and m/Torr. The display range is 760 Torr down to 0 mTorr (Maximum permitted end vacuum is 10 mTorr. Leak rate is 30 mTorr in 30 min). A secondary independent high limit controller provides overtemperature safety protection. This unit includes true vacuum valves and has cross-flow ventilation within the oven chamber to enhance total performance. The vacuum oven is secured to a ruggedly constructed mobile stand to create a vacuum pump at the base. Although the oven is not supplied with a vacuum pump, all vacuum plumbing and KF25 connections are provided. The SHEL LAB SVAC9-2 vacuum oven is equipped with a Viton gasket, which provides an excellent combination of high-temperature performance and chemical resistance. When paired with this oven’s deep-draw capacity and large chamber volume, the SVAC9-2 serves as one of the most robust vacuum work stations available on the market. Features include: Watlow PM9 Plus Controller Capable Of 40 Step Ramp And Soak Profiles, Or 4 Files With 10 Steps Per File Stainless Steel Interior Stainless Steel Exterior Option Available (Ideal For Cleanroom Applications) KF25 Fitting Included Built in Vacuum Pump Mount 24 Month Limited Warranty
$33,152.62$26,185.79
Sheldon Manufacturing - OVEN, FORCED AIR, 1.5 CUFT
Sheldon Manufacturing - OVEN, FORCED AIR, 1.5 CUFT The SMO1 has a quick ramp-up time to 306°C for faster cycle times. This unit includes an advanced PID temperature control system for sensitive response. These ovens are recommended for critical and analytical use in laboratory and pilot plant product research. Typical applications for the oven include aging, asphalt testing, curing, drying, pre-heating, conditioning, and life cycle testing. This unit is equipped with a stainless-steel interior for long-life operation and easy cleaning. Its triple wall construction minimizes external wall temperature which meets CE requirements to keep work spaces cool. The SMO1's forced air ovens deliver precise uniformity, air distribution and the peace of mind expected of the SHEL LAB brand. Features of this oven include: Embedded Microprocessor Control with Countdown Timer Horizontal Forced Airflow 1.75in (45 mm) Access Port UL/CSA Approved CE Approval DIN 12880 Compliant 24 Month Limited Warranty Options: SMO1: OVEN, FORCED AIR, 1.5 CU FT, 115V SMO1-2: OVEN, FORCED AIR, 1.5 CU FT, 230V
$4,387.89 - $4,494.05
Sheldon Manufacturing - OVEN, FORCED AIR, 3 CUFT
Sheldon Manufacturing - OVEN, FORCED AIR, 3 CUFT The SMO3 has a quick ramp-up time to 306°C for faster cycle times. This unit includes an advanced PID temperature control system for sensitive response. These ovens are recommended for critical and analytical use in laboratory and pilot plant product research. Typical applications for the oven include aging, asphalt testing, curing, drying, pre-heating, conditioning, and life cycle testing. This unit is equipped with a stainless-steel interior for long-life operation and easy cleaning. Its triple wall construction minimizes external wall temperature which meets CE requirements to keep workspaces cool. The SMO3 forced air oven delivers precise uniformity, air distribution, and the peace of mind expected of the SHEL LAB brand. Features of this oven include: Embedded Microprocessor Control with Countdown Timer Horizontal Forced Airflow 1.75in (45mm) Access Port UL/CSA Approved CE Approval DIN 12880 Compliant 24 Month Limited Warranty Options: SMO3: OVEN, FORCED AIR, 3 CU FT, 115V SMO3-2: OVEN, FORCED AIR, 3 CU FT, 230V
$4,847.91 - $4,918.68
Sheldon Manufacturing - OVEN, FORCED AIR, 5 CUFT
Sheldon Manufacturing - OVEN, FORCED AIR, 5 CUFT The SMO5 is equipped with a stainless-steel interior for long-life operation and easy cleaning. With triple wall construction, this oven’s walls minimize external wall temperature which meets CE requirements to keep work spaces cool. These ovens are recommended for critical and analytical use in laboratory and pilot plant product research. Typical applications for the oven include aging, asphalt testing, curing, drying, pre-heating, conditioning, and life cycle testing. This unit has a quick ramp-up time to 306°C for faster cycle times. This unit includes an advanced PID temperature control system for sensitive response. The SMO5 forced air oven delivers precise uniformity, air distribution, and the peace of mind expected of the SHEL LAB brand. Features of this oven include: Embedded Microprocessor Control with Countdown Timer Horizontal Forced Airflow 1.75in (45 mm) Access Port UL/CSA Approved CE Approval DIN 12880 Compliant 24 Month Limited Warranty
$5,789.18 - $5,874.11
Sheldon Manufacturing - FORCED AIR OVEN, 13.8 CUBIC FEET, 230V
Sheldon Manufacturing - FORCED AIR OVEN, 13.8 CUBIC FEET, 230V The SHEL LAB SMO14-2 features 14 cubic feet of economical oven space. The independent overtemperature safety feature is user adjustable and provides added safety. The forced, blower-assisted airflow design offers excellent temperature uniformity and fast recovery. A turbo blower and heavy-duty motor combine to direct air over the shelves and samples for even, constant drying, curing, and baking. The large capacity SMO ovens are perfect for high volume sample and drying applications, including production processes. These units are especially ideal for glassware drying. These SHEL LAB Ovens Feature: Three-inch Adjustable Exhaust Port Stainless Steel Shelves Independent Overtemperature Safety High-Temperature Silicone Door Seal Added docking collars to intake and exhaust ports to allow ducting to be attached for venting exhaust out of the workspace Shelf standards moved to the sides of the unit for easier shelf installation No Exposed Heating Wrap Around Insulation Durable Powder Coat Paint Exterior Finish Digital Timer 24 Month Limited Warranty
$9,561.35$7,926.51
Sheldon Manufacturing - FORCED AIR OVEN, 27.6 CUBIC FEET
Sheldon Manufacturing - FORCED AIR OVEN, 27.6 CUBIC FEET The SHEL LAB Model SMO28-2 is the largest general-purpose oven on the market. The independent overtemperature safety feature is user adjustable and provides added safety. The turbo blower-assisted forced airflow design coupled with a heavy-duty blower motor offers excellent temperature uniformity and fast recovery times. Airflow is directed evenly across all shelves and samples to ensure consistent drying, curing, and baking results. The SMO large capacity units are perfect for high volume sample and drying applications, including production processes. These units are especially ideal for glassware drying. These SHEL LAB ovens Feature: Three-inch Adjustable Exhaust Port Stainless Steel Shelves Independent Overtemperature Safety High-Temperature Silicone Door Seal No Exposed Heating Elements Added docking collars to intake and exhaust ports to allow ducting to be attached for venting exhaust out of the workspace Shelf standards moved to the sides of the unit for easier shelf installation Wrap Around Insulation Durable Powder Coat Paint Exterior Finish Digital Timer 24 Month Limited Warranty
$13,441.09$10,092.14
You have seen 213 out of 213 products