Non BVV product for sale
Inland FF-10 Flushing Fluid
Inland FF-10 Flushing Fluid Inland FF-10 is a solvent free hydrocarbon flushing fluid designed to be used as part of a preventive maintenance program. Periodic use of FF-10 will enable the user to remove contaminants and particulates from within all areas of the pump without the worry of contaminating the pump with an expensive solvent Specifications FF-10 Vapor Pressure at 25ºC (torr) 2x10-4 Viscosity at 40ºC (cSt) 28 Viscosity at 100ºC (cSt) 4.5 Flash Point (ºC) 199 Fire Point (ºC) 221 Density at 25ºC (g/ml) 0.85 Inland FF-10 Flushing Fluid Safety Data Sheet SDS
$19.67 - $1,433.35
Inland 70 Ultra Vacuum Pump Oil (Edwards Ultragrade 70)
Inland 70 Ultra Vacuum Pump Oil This is oil is a direct replacement for Edwards Ultragrade 70 oil. Specifications Inland 70 Ultra Vapor Pressure @25°C 1x10^-7 torr Viscosity @ 40°C 72 cSt Pour Point: -10°C Flash Point: 249°C Density: 0.86 g/ml Color: Clear Inland 70 Ultra Safety Data Sheet PDF
$23.89 - $2,608.84
LSD QTests
LSD QTests Know your dose with the LSD QTest The LSD QTest is the world’s first quantitative LSD test kit on the market. It can tell you how many micrograms are in each square of your blotter or each drop of liquid . . . before you ingest it. Use one drop of liquid or one half a hit of blotter, then compare the color of the detection vial to the enclosed color chart. It’s that simple. Instructions Note: A paper version of these instructions comes with your order. IMPORTANT INFORMATION! – READ THIS FIRST • Use this kit at room temperature. (If stored in a refrigerator, let it warm up for one hour first.) • Perform the test on a flat surface during the daytime. • Evaluate the result in daylight immediately after the 12-minute development time. (The color can change if you wait too long.) • Use a white, letter-sized sheet of paper as a background when evaluating the color. (See section four for evaluation details.) • Read all the instructions at least once through before beginning the test. 1. BACKGROUND INFORMATION This test kit can be used to detect the active ingredient LSD-25 (lysergic acid diethylamide) and its concentration in blotter, liquid, and sugar cubes. It does not work on gel tabs. The kit does not react to 1P-LSD, 1cP-LSD, ALD-52 or ETH-LAD When testing blotter, you should only test half of a dose. The end result will tell you how many micrograms of LSD are in the entire dose.* When testing liquid LSD, use only one drop. But remember, the end result tells you how much is in two drops.** When testing sugar cubes, you need to crush and mix up the sugar first. Weigh out and test one quarter (1/4th) of the sugar, then multiply the end result by two.*** IMPORTANT! – Always shake your vial of liquid LSD (and empty and refill the dropper a few times) before dosing out a drop. Liquid LSD tends to settle at the bottom of the vial. If you forget to shake it first, you could end up accidentally ingesting a dose ten or even twenty times larger than expected. Similarly, the liquid in a vial of LSD can evaporate over time, increasing its concentration. (The LSD doesn’t evaporate away. Only the liquid evaporates.) This is particularly true with alcohol solutions, and it can happen even when the lid is tightly closed. Make sure and take this into account. Older vials that have been sitting around for many months can become more potent over time. * Each perforated square in a given sheet of blotter will typically be the same dose. This is because the entire sheet was dipped into a tray of liquid LSD, and the LSD was absorbed evenly throughout the sheet. We designed the LSD QTest so that you only need to test half of a dose (half a square of blotter), and the result will tell you how much LSD is in each full dose (each full square of blotter) belonging to the same sheet. Keep in mind if you have individual squares of blotter that are not connected to each other (i.e., if the perforation was broken when you obtained them) then they may not come from the same sheet. Only connected squares can be assumed to come from the same sheet. ** When testing one drop of liquid LSD, the result tells you how much LSD is in two drops. So remember to divide the end result in half in order to determine how much LSD is in one drop. *** When a drop of liquid LSD is individually dropped onto an absorbent medium such as a sugar cube, it does not absorb evenly. This is why you need to homogenize it before you test it (by crushing and mixing thoroughly). Also, all that sugar won’t fit into the extraction vial, so just use a quarter of it. Then multiply the end result by two to determine the amount of LSD that was originally in the entire cube. 2. PREPARING FOR THE TEST Take out all the items from your kit. Along with these instructions, you should have: • protective gloves• glass vial with screw cap (the extraction vial)• dropper vial with green lid (detection reagent)• evaluation color chart 3. PERFORMING THE TEST 3.1 First put on the enclosed nitrile gloves and wear appropriate protective clothing and safety glasses. If you wear contact lenses, remove them. The liquids in the vials contain acids which may cause skin irritation or severe eye damage. In the event you come in contact with the liquid, remove the affected clothing immediately and rinse the affected skin area with water for several minutes. In case of eye contact, rinse the affected eye with running water for several minutes. (Keep pets, especially cats, away from the testing area.) If you are testing blotter, carefully cut it in half diagonally from one corner to the other using a fine pair of scissors. If you are testing a sugar cube, put it into a small zip lock baggie. Crush it up and shake it well, then pour all of it onto a milligram scale and weigh it. Write down the total weight. Now use the same scale and weigh out one quarter (1/4th) of the total for the test. 3.2 Open the glass vial and add the half piece of blotter (or the quarter amount of sugar). If you are testing liquid LSD, just add one drop. Put the lid back on the vial, close it tightly and shake it for about one or two minutes. For blotter, let the vial rest for five minutes and then repeat the process two more times to make sure all the LSD is extracted. During the five-minute resting periods, make sure the blotter is suspended in the liquid, not stuck to the side of the glass, or to the underside of the lid. Shaking three times with a five minute resting period in between is enough to extract all the LSD even from the thickest blotter. (For thinner blotter, you don’t really need to repeat this process three times, but we suggest it anyway just to make sure.) 3.3 Open the extraction vial again and place it in a safe position. Remove the green cap from the plastic dropper vial and carefully empty the entire contents into the glass vial by squeezing it with even pressure. Put the lids back onto both vials and close them tightly. 3.4 Gently invert the glass vial four or five times to mix the reagents together and then set the vial down. In the presence of LSD, the liquid will begin turning a blue color immediately. 3.5 Wait 12 minutes for the color to completely develop. The result can then be read and interpreted using the enclosed color chart. See the next section, “EVALUATING THE RESULT,” for details. IMPORTANT! – If you see blue spots or streaks on the blotter, this indicates that not all the LSD got extracted from the blotter. In this case the result will be inaccurate. (Your LSD is actually more potent than the result indicates.) This will only happen with thicker blotter if you did not carefully follow the instructions in section 3.2 above. 4. EVALUATING THE RESULT Follow the instructions above and wait 12 minutes before evaluating the result, but do not wait much longer than 12 minutes. Set a timer. By comparing the intensity or saturation of the liquid in the vial with the enclosed color chart, you can determine the result visually. In the presence of LSD-25, the detection reagent turns bluish over time. Daytime sunlight is best suited for optimal evaluation. If using artificial light, the influence of different color temperatures may slightly change the hue. You can still perform the evaluation, but you should take this into account (e.g. high blue content in energy-saving lamps, green discoloration when using LED light from cell phones, etc). SPECIFIC EVALUATION INSTRUCTIONS • Use a white, letter-sized sheet of paper as a background.• In daylight or under bright light, hold the glass vial next to the color chart about six to eight inches in front of the white sheet of paper and look through the glass vial head on. For best results, your eyes should be fairly close to the vial, but no closer than about six to eight inches.• Now compare the color of the liquid in the vial to the color chart. The corresponding concentration of LSD listed on the color chart is twice the amount of LSD that you tested. So if you tested half a square of blotter, the concentration listed indicates the amount of LSD present in the entire square.• If you tested one drop of liquid, the corresponding result indicates how much LSD is in two drops of the liquid. (So divide the result in half to calculate how much is in one drop.)• If you tested a quarter of a sugar cube, the result tells you how much LSD is in half the sugar cube. (So multiply the result by two to calculate how much LSD was in the entire, original cube.) 5. STORAGE AND SHELF LIFE Store the reagents in the refrigerator (35° – 46° F) and out of direct sunlight for a shelf life of at least 18 months. 6. WARNINGS • Keep the kit away from children and animals.• When performing the test, wear suitable protective gloves, clothing and face/eye protection. If you wear contact lenses, remove them before using the test kit.• The liquids contained in the dropper vial consist of various acids which may cause a corrosive/irritating effect on the skin or severe eye damage/irritation. Avoid contact with the skin, eyes, mouth or clothing.• Should contact with the above listed areas occur, remove the relevant clothing immediately. Instantly rinse the affected skin areas with water for several minutes. In case of contact with the eyes, immediately rinse them with water for several minutes using both hands to keep the upper and lower eyelids open.• Substances processed with the test kit are not to be consumed!• The solution in the extraction vial is flammable. It’s just a small amount, but please don’t smoke while performing the test. 7. DISCLAIMERS • QTests are only to be used for the detection and quantification of unknown substances.• The result may not be 100% accurate. Your sample could be adulterated with one or more unknown substances that cross-react with the reagents, affecting the quantitative result.• The result does not mean your sample is safe to consume. It could still contain unwanted substances and impurities that can be harmful or even deadly.• The LSD QTest is not a substitute for laboratory analysis.• miraculix and/or Qtests.org assume no responsibility for the use or misuse of the test kit or the results. 8. DISPOSAL OF MATERIALS Check your local regulations for proper disposal of acids.
$35.06
Female Elbow
SSP - Female Elbow SSP Instrumentation TruFit® is manufactured from fully-traceable raw material to close tolerances and superior surface finishes. TruFit® provides optimal performance when installed in accordance with SSP’s recommendations and the design parameters appropriate for each type of connection – tapered thread, straight thread, and weld & braze. TruFit® components are cleaned in accordance with SSP documented work instructions using equipment calibrated to NIST standards with environmentally-safe and stable agents, ultrasonics, and heat/ temperature to remove all residual oil, grease, and loose particles. Stainless steel components are passivated to the requirements of MIL QQ-P-35 and ASTM A 967. ***Note: ALL NPT Threads REQUIRE the user to properly install the fitting by using a thread sealant to prevent leaks. BVV recommends GAS PTFE Tape Specifications Connection Type 1 Female NPT Connection Size 1 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Working Pressure (PSIG) 1/4" - 7750 3/8" - 6800 NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!
$14.05 - $19.67
So-Low -85°C Ultra-Low Chest Freezer - 5 Cubic Ft.
So-Low -85°C Ultra-Low Chest Freezer - 5 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! So-Low Ultra-Low Chest Freezers are second to none in low temp applications to suit any laboratory or application needs. These Ultra-Low Temp freezers feature digital temperature control with 2 temperature displays. One shows the set temperature and the other shows the actual temperature in the freezer. The So-Low C85-5 features a battery operated alarm system that will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Product Specifications Temperature Control Digital Control with two temperature displays. One display shows the set temperature, the other shows the actual temperature in the freezer. Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Refrigeration System So-Low cascade type. Two hermetic compressors. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 208/60/1 - 230/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet Specification Manufacturer So-Low Temperature Range -40°C to -85°C / -40°F to -121°F Capacity 5 Cubic Ft. / 142 Liters Dimensions: Exterior: 40.5" x 31" x 47" Interior: 30" x 18" x 16" Refrigeration System So-Low cascade type. Two hermetic compressors. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish.
$9,555.68 - $10,258.30
Julabo Adapter M16x1 f to NPT 1/2″
Julabo Adapter M16x1 f to NPT 1/2″ 2 Adapters M16x1 f. to NPT 1/2″ m.
$295.10
CHEMTEK D-Wax
CHEMTEK D-Wax D-Wax is a silica with high adsorption capacity and strong affinity for phospholipids, trace metals, and soaps. It contains 50% water and citric acid to remove both hydratable and non hydratable phosphatides. D-Wax SDS
$112.42 - $646.41
Media Bros Medium flow CRX-M
Media Bros Medium flow CRX This non-reactive medium flow variant allows operators to increase operating pressures and surface area for a more fine-tuned process. PH 7 Description: Introducing CRX Medium Flow™ (CRX-M™), a not-quite-powder/fine-grain premium filter media formulated for non-reactive, high flow and high-pressure hydrocarbon extraction. Its texture is designed to replace traditional powdered media like B80 without channeling and clogging issues commonly encountered with conventional powders. Extractors accustomed to traditional powders like B80 will find that CRX-M™ offers similar flow properties but with the added benefit of superior terpene retention. Like all of our premium blends, CRX-M™ is non-reactive, ensuring it's safe and easy to handle in your lab setting. It eliminates the need for extensive clean-up, saving you time and effort. CRX-M™ has all the benefits of its more granular twin, the flagship CRX™. It is a "perfect scrub" media, ideal for high-quality biomass and nug run processing. You want total control over flow and ensure the terpenes and flavonoids are retained from plant to extracted oil. Extraction labs vary in size, and so does our range of filter media. Our CRX-M™ product is available in three convenient packaging options: a 1.5 kg pouch, a 10 kg bucket, and a 100 kg drum. Whether operating on a small scale or running an extensive industrial process, we have the perfect packaging to meet your needs. Technical Specs: Solvent Type Hydrocarbon Color Remediation Level Average/Moderate Pesticide Remediation Level Low Selectivity/Polarity Level Moderately Selective/Medium Polarity Heavy Metal Remediation No Moisture Remediation Level Low Fats/Lipids/Waxes Level Medium Crystal Growth Fast Depth Filtration No Flow Rate Moderate Flow pH Level Neutral (pH 7) Best For Fresh Frozen, Nugs, High Quality Suitable for Reruns No Distillation Clean-up Low Scrub SOP SDS Before you get started, please remember this: As CRX™ and CRY™ are not powders designed not to absorb moisture before use, no baking or preparation is needed. For optimal success, ensure your flow is gentle and consistent. RATIOS Solvent to Biomass: ratios range from 6:1 to 10:1, depending on the quality of the plant matter you are distilling—lower ratios for top-tier biomass and higher ratios for older or lower-quality biomass. Media to Biomass: Load 150 - 250 grams of filter media into filtration housing for every 1 lb of biomass. The media quantity used is dependent on the quality of the biomass. Higher-quality biomass requires less media. Lower-quality biomass requires more media. The lookup table can be used as a reference, but because every kind of plant matter is different, you will need to experiment a little bit to achieve the best results. That said, this chart is an excellent baseline from which to start. TEMPS To ensure optimal performance, keep the temperature at -10°C or below while using the media. Our media is designed to prevent clogging. FLOW When transferring from the biomass vessel to the recovery vessel, maintain a maximum flow rate of 1 GPM. Our media performs best with a consistent and gentle flow. To prevent channeling, avoid sudden hydraulic surges through the CRC column. A shower or initial fill of the column is highly recommended for optimal results. YIELD Any lost yield can be fully recovered by flushing the media with solvent. Most users report achieving substantial yield gains by maintaining high solvent-to-biomass ratios or flushing our media after an extraction transfer.
$42.16 - $2,248.40
Edwards nXDS Series Dry Scroll Pumps Tip Seal Service Kit
Edwards nXDS Series Dry Scroll Pumps Tip Seal Service Kit The nXDS series is the next generation in completely oil free, dry scroll pumps nXDS improves on legacy XDS pumps by offering increased pumping speeds, combined with lower ultimate pressures, lower power consumption and lower noise. Gas ballast allows for pumping of condensable vapours including, water, solvents, dilute acids and bases. nXDS pumps also feature the latest in tip seal technology giving significantly longer life between tip seal changes. Integrated inverter drive with auto sensing voltage input delivers optimized pumping performance globally. nXDS pumps are designed to be completely field serviceable. Features: Lubricant-free within the vacuum envelope and hermetically sealed means totally clean and dry vacuum to prevent cross contamination No atmosphere to vacuum shaft seals means bearings are completely isolated, which prevents process attack and means the bearings run cooler and last longer Simple single sided scroll arrangement combined with an innovative motor and bearing design allows for easy field service with a minimum of special tooling for low cost of ownership and maximum up-time Improved motor and drive efficiencies for reduced power and cost of ownership Advanced interface provides a variety of traditional, analogue and digital control methods enabling remote control/monitoring via USB, RS232 or RS485 One year warranty, as well as technical
$822.07
Welch CRVpro Direct Drive Rotary Vane Vacuum Pump CRVpro8
Welch CRVpro Direct Drive Rotary Vane Vacuum Pump CRVpro8 ***Note: This item has a possible 1-2 week lead time depending on stock availability*** Product Details The new CRVpro family of direct drive vacuum pumps offers increased reliability and longer service interval vs. other direct drive rotary vane vacuum pumps. The CRVpro family consumes up to 36% less oil than comparable pumps. Three features drive these benefits: Runs 10°C cooler than comparable pumps. Slows corrosion. Has a 40% larger oil capacity than comparable pumps. Dilutes aggressive chemicals. Has a chemical resistant coating in the oil case and pump module. Protects non-moving parts. The CRVpro family includes all the features you'd expect in a direct drive rotary vane pump: gas ballast, forced oil lubrication, anti-suckback mechanism and thermal overload protection. Suitable applications include freeze drying, degassing, vacuum ovens and concentrators. 3081-01 is wired for North American 115V, 60Hz operation. Includes North American line cord, vacuum inlet hose barb suitable for gum rubber hose from 5/8" to 3/4" ID, and a charge of oil. 3082-01 is wired for North American 230V, 60Hz operation. Includes 230V North American line cord, UK cord, and skuko cord, and a charge of oil. Direct drive pumps are not recommended for filtration, aspiration, drying electrophoresis gels, or other applications requiring sustained operation above 30 torr Specifications Application CRVpro8 Free Air Displacement @ 60 Hz, cfm (L/min) 5.6 (158) Free Air Displacement @ 50 Hz, m³/hr (L/min) 8 (133) Ultimate Pressure, torr (mbar) 5x10⁻⁴ (4x10⁻⁴) Noise Level, dBA 50 Motor Speed, RPM, @60Hz, @50Hz 1740 (1450) Motor Power, HP (kW) 0.4 (0.5) Oil Capacity, mL 1000 Connection Flanges NW 16 Inlet Hose Connection* 5/8" to 3/4" Weight, lbs (kg) 49.6 (22.5) Dimensions, LxWxH, in (mm) 18.2x6.1x9.1 (463x157x230)
$5,831.78
Polyscience Model 210 Heated Recirculator
Polyscience Model 210 Heated Recirculator Specification Description Heated Recirculator Working Temperature Range °C Ambient to 70° Temperature Stability °C ±0.2° Pump Type Centrifugal Working Temperature Range °F Ambient to 158° Working Temperature Range °C Ambient to 70° Temperature Stability °F ±0.4° Temperature Stability °C ±0.2° Pump Type Centrifugal Pump Speed Single Process Connections 1/2" barb fitting Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 8 x 9.5 x 8 in Overall Dimensions (L x W x H) (cm) 20.3 x 24.1 x 20.3 cm Shipping Weight (pounds) 12.0 Shipping Weight (kilograms) 5.4 Catalog Page Number 67 60 Hz Only Part Number 40300 Maximum Pressure (psi) 2.0 Maximum Pressure (bar) 0.13 Maximum Pressure Flow Rate (gpm) 3.00 Maximum Pressure Flow Rate (l/min) 11.4 Included Hardware Tubing and clamps Heater Wattage 750 key Features: Low-cost pumping and heating for closed-loop applications Provides accurate control within a frequently used temperature range Ideal for applications such as thawing plasma, temperaring photographic solutions or circulating to an external device Over-Temperature Protection Failsafe Heater Control Operator's Manual
$2,245.59
Pump Part - MVP - 60 PSI, 150 PSI, Liquid, XL150 - Diaphragm Cover Bolts - 8 pack
Pump Part - MVP - 60 PSI, 150 PSI, Liquid, XL150 - Diaphragm Cover Bolts - 8 pack All sales final
$154.58
Julabo Adapter 8891609 M16x1 f to NPT 1/2″ f
Julabo Adapter 8891609 M16x1 f to NPT 1/2″ f 2 Adapters M16x1 f. to NPT 1/2″ f.
$359.74
Julabo C5 Thermal Bath Fluid - 10 Liters
Julabo C5 Thermal Bath Fluid JULABO Thermal bath fluids are ideally suited for all of your temperature control applications and guarantee safe and reliable operation. Choosing the proper bath fluid is critical for best results in temperature control. Viscosity, oxidation characteristics and heat transfer of Thermal fluids are specifically matched with each JULABO temperature control unit. C5 Thermal Bath Fluid SDS C5 Thermal Bath Fluid Product Data Sheet JULABO Thermal bath fluids have been carefully selected and are optimized for maximum performance with JULABO instruments. Benefits Low toxicity Low viscosity High stability Minimum odor Good heat conductivity Low corrosion tendency Wide temperature ranges Technical Data Order no. 10 liters 8891402 Working temperature (°C) -60...+110 Flash point (°C) > +135 Fire point (°C) > +443 Viscosity (kinematic at 20 °C in mm²/s) 5 Density (at 20 °C in g/cm³) 0.918 Pour point (°C) -100 Boiling point (°C) >205 Ignition temperature (°C) 443 Color clear
$2,970.69
Huber SilOil M80.100/250.03, Heat transfer fluid -80 to 250°C
Huber SilOil M80.100/250.03, Heat transfer fluid -80 to 250°C SilOil M80.100/250.03 is a low-viscosity silicone fluid which, as a result of its special property profile, is particularly suitable for use as a cold and heat transfer medium in cryostats, thermostats and heat transfer installations. SilOil M80.100/250.03 can be used in the range from -80 °C to 100 °C (for open systems) and to 250 °C with externally sealed systems (Unistats). It should be borne in mind that, at high temperatures, SilOil M80.100/250.03 can be chemically altered by oxidizing media, such as air, or substances with a catalytic effect, such as acids, lyes and various metal compounds. An increase in viscosity, and possibly even gelling of the fluid owing to crosslinking reactions, must be expected in the presence of oxidising agents, while contact with products having a catalytic effect usually induces a process of depolymerization, resulting in a drop in viscosity Safety Data Sheet Advantage: virtually insoluble in water non-corrosive low setting points and vapor pressures high flash points low toxicity odorless no coking tendency under thermal stress high thermal stability resistance to ageing chlorine free Heat transfer fluid M80.100/250.03 Working temperature °C -80 to 100/250 open/closed systems: -80°C - 100°C Unistats (only closed): -80°C - 250°C Material: silicon oil Viscosity at 25°C: 7 mm²/s Color colorless, clear Material incompatibility Silicone rubber
$2,655.92 - $5,072.94
HUBER CS Chillers
HUBER CS Chillers The new CS chillers expand the Huber product range with compact and highly affordable recirculating coolers. The Huber CS chillers combine cool and smart technology in one unit. The new chillers further reduce water consumption and lower the operating costs for many applications. The investment pays itself off after a short time because of the water savings and the low purchase price. Your advantages: Working temperature from -20 °C to +15 °C Cooling power up to 70 kW Pump performance up to 125 l/min Quiet operation less than 79 db Economic and ecological solution to eliminate costly water waste Easy to use and maintenance free With a cooling power up to 70 kW, the devices are particularly suited for constant temperature control for laboratory applications, e.g. for cooling vacuum pumps, rotary evaporators, electron microscopy, AAS-devices, ICP-devices, extraction, distillation and many more. Sku Model Temperature Range Pump Vapacity Max/Pump Connection Cooling power(kW) at (°C) HeatingPower NoiseLevel Dimensions Voltage Data Sheet (°C) (l/min) (bar) 15 10 0 -10 -20 (kW) (dB) W x D x H (inch) PDF VDH1100664 CS 25 -20...15 50 4.5 1/2" 3.5 2.5 1.6 0.98 0.7 - 60 22.8 x 26.0 x 32.3 208V 2~ 60Hz VDH1101336 CS 35 -20...15 30 4.0 1/2" 4.0 3.5 2.1 2.0 0.8 62 22.8 x 26.0 x 32.3 208V 2~ 60Hz VDH1100689 CS 50 -20...15 83 4.0 3/4" 8 5 4.2 3.5 2 - 63 26.8 x 28.7 x 59.8 460V 3~ 60Hz VDH4100126 CS 50-H -20...85 83 3.7 3/4" 8 5 4.2 3.5 2 2.8 63 26.8 x 28.7 x 59.8 460V 3~ 60Hz VDH1100690 CS 100 -20...15 83 4.0 3/4" 18 10 9.5 7.5 4.5 - 70 31.5 x 33.5 x 65.6 460V 3~ 60Hz VDH4100106 CS 100-H -20...85 83 3.7 3/4" 18 10 9.5 7.5 4.5 5.5 70 31.5 x 33.5 x 65.6 460V 3~ 60Hz VDH1100688 CS 200 -20...15 125 4.2 1" 28 20 18 15 9.5 - 78 55.1 x 39.4 x 70.9 460V 3~ 60Hz VDH4100091 CS 200-H -20...85 125 4.2 1" 28 20 18 15 9.5 5.5 78 55.1 x 39.4 x 70.9 460V 3~ 60Hz
$21,781.33 - $80,450.40
HTP Big Daddy Press - 2 Ton
HTP Big Daddy Press - 2 Ton If you are looking for a quality press then the Big Daddy Press is for you! These high quality presses are built from Aircraft Aluminum and stainless steel designed to be used in conjunction with a unique heating process.The Big Daddy Press operates with a 2-Ton Hydraulic cylinder. It has a capacity of 3x3.High Tech Pipes make quality presses that are manufactured in the U.S.A. using American materials and labor. Each Press is assembled and individually inspected before shipping. Our Presses are designed to be heated to the ideal temperature which is an important aspect of the Pressing process. We design and build our products to stand the test of time and to become a permanent piece of equipment for the end user. We use aircraft aluminum which maintains heat as opposed to other Presses on the market which use steel that either quickly loses heat or heats up too fast thus destroying the material that is being pressed. Each Press comes with full step by step instructions and a video is available as well.
$590.13$555.07
Cascade 20L Bead Bath with 15L Lab Armor Beads
Cascade 20L Bead Bath Bye-Bye Water Bath! Traditional water baths are associated with messy condensation and the growing of harmful germicides. Cascade Sciences Bead Baths are the next generation of a decades-old lab bath technology. With the included thermal beads, this 20L Cascade Bead Bath operates in a constant, stable, broad temperature range between -80°C to +180°C. The bath itself delivers exceptional temperature uniformity up to 80°C. Zero Evaporation Saves Energy In a water bath, the water is constantly evaporating. As water evaporates, it cools. Because evaporation has a cooling effect, a water bath must heat more frequently. A bead bath uses 4X less energy when set to 65°C and 2X less energy at 37°C. The bead bath also provides more constant temperature with fewer temperature fluctuations during operation. Cascade Sciences Bead Baths and Thermal Beads and Made in the USA and NRTL Certified Cascade Sciences Bead Bath Features: High Thermal Efficiency Microbial/Biofilm Resistant Cross-Contamination Resistant Minimal Cleaning No Refilling No Rack or Accessory Needed Angled Incubation Possible Constant Volume – No Evaporation Non-Corrosive Compatible with non-water tight vessels Independent build-in over-temp, burn-out protection No Warm Up Mobile or Field Use Compatible Non-Combustible Thermal Beads Replace Water and Ice Lab Armor™ Thermal Beads are small, dry, metallic thermal beads designed to replace water in laboratory water baths and ice in ice buckets. Their high thermal conductivity technology is patented and improves energy efficiency of standard water baths by over 50%. Improve lab cleanliness when using thermal beads in place of fluid in water baths. Thermal Beads – Recyclable Lab Armor™ Thermal Beads are formed from solid recyclable metal. The raw material used in Lab Armor™ Beads can be reused in other products. Lab Armor™ Thermal Bead Features: Metal composition with smooth round surface Moisture and gas impermeable High thermal conductivity Working temperature range is -80°C to 180°C Non-toxic, non-vaporizing material Recyclable! Multiple uses – ice replacement Frequently Asked Questions Are Lab Armor™ beads autoclavable?They are not. The steam and pressure ruins the surface of the beads. We recommend a dry heat sterilization: 180°C for 2.5 hours. For a quick touch-up we recommend spritzing with 70% ethanol and stirring. If some debris falls into the beads we recommend placing them in a pail with water and a small about of Dawn, rinsing out multiple times, and then putting through the dry heat sterilization process. How long can I use Lab Armor™ Beads under normal conditions?Under normal conditions, Lab Armor™ Beads should last the life of the bath. If used incorrectly or if not maintained and cleaned properly, the surfaces of Lab Armor™ Beads can become damaged. We recommend that you avoid strong detergents, acids and bases. Bleach, for instance, may tarnish the surface of the Lab Armor™ Beads, reducing its fluidity and overall performance. Can Lab Armor™ Beads be used as an ice bath?There are a number of different ways to use thermal beads. Many customers place containers of beads in their refrigerators, incubators and ovens. When creating an ice bath, be sure to keep the beads dry. We recommend separating the beads from the ice packs, which accumulate condensation. Some kind of mesh wire or fabric helps with this as well. Also, any condensation that builds on the surface of the beads will be able to drip through the mesh. It’s important to keep the beads from soaking in water for extended periods of time. Besides attracting contamination, excessive water contact will tarnish the surface of the Beads and reduce the fluidity of the bath. Also, as an alternative to ice packs, dry ice can be used to make a colder bath (<0ºC).
$4,848.10
KING KONE CLOSER
KING KONE CLOSER Crown your pre-roll with a Dutch finish in just 4 easy steps. With this closer, you can produce up to 1,000 pre-rolls per hour from start to finish. Out of Stock: Due to high demand and the time required to craft this product, availability may take longer than our other items. At this time, we are not accepting pre-orders. We appreciate your patience as we work to fulfill all orders. Size: 109mm cone/King Size Cone Thank you for your understanding!
$2,528.04 - $2,810.49
Tip Seal Kit For Agilent IDP3, IDP7, IDP10 Or IDP15
Tip Seal Kit For Agilent IDP3, IDP7, IDP10 Or IDP15 Agilent tip seal replacement kit for IDP-3, IDP-7, IDP-10 or IDP-15 dry scroll pumps.
$449.68 - $765.86
The Press Club 5 Gallon All-Mesh Bubble Bags BUBBLE BAGS
The Press Club 5 Gallon All-Mesh Bubble Bags BUBBLE BAGS The Press Club Wash Bags are the last set of bubble wash bags you'll ever own! Made from premium, food-grade material specifically for washing you can stop second guessing whether you have the right or best bags in the industry. All our bubble wash bags are hand sewn with our proprietary pink stitching, making them 2x stronger than competitors. You can be confident our bags will perform the same no matter if it's your 1st or 1000th wash. We're so confident our bubble wash bags will stand the test of time, every bag comes with a Lifetime Warranty. If you have any manufacturer issues, we'll be more than happy to replace the bag for you! KEY FEATURES Fits All Standard 5 Gallon Buckets Hand Sewn With Our Proprietary Pink Stitch w/ Food-Grade Materials Military-Grade Waterproof & No Flaking Bag Liner Premium Drawstring & Cord Locks To Secure Bags Lifetime Warranty On All Wash Bags Includes Meshed Carrying Case For 2-Way Drying & Storage Made In USA AVAILABLE MICRONS 220 Micron (Work Bag), 190 Micron, 160 Micron, 120 Micron, 90 Micron, 73 Micron, 45 Micron, 25 Micron
$56.14
Welch 2062/2064/2067 8 Head Diaphragm Replacement Kit
Welch 2062/2064/2067 8 Head Diaphragm Replacement Kit Service kit for 2064/2067/2062/2163 (8-head)
$1,672.24
Welch ProBoost Air-Cooled Diffusion Pump
Welch ProBoost Air-Cooled Diffusion Pump Product Details Use Welch ProBoost in conjunction with a backing pump like the CRVpro to get deeper vacuum and higher flow. High Vacuum to 10⁻⁵ torr Use with high vacuum and Schlenk lines Employs air cooled diffusion pump Easy Attachment to backing pump Welch ProBoost is an air cooled gas jet pump (commonly called a diffusion pump). The gas jet is formed by directing boiling silicone vapors through a hollow cone. There are no internal moving parts. The pumping action commences when the vacuum pressure in the still (i.e. wiped film) goes below 0.2 torr (200 millitorr). On an empty, leak free still, ProBoost backed by a rotary vane pump lowers the vacuum pressure to 0.00002 torr (20x lower in pressure than a 2-stage rotary vane vacuum pump can do alone). ProBoost backed by a rotary vane vacuum pump will lower vacuum pressure to below 0.0001 torr in high vacuum and Schlenk lines. This high vacuum is invaluable to improve the results from reactions using air-sensitive compounds such as organometallics, metal amides, and hydrides. ProBoost has a built-in control board for fan and heater. When you turn on ProBoost, the fan and heater both turn on. When you turn off ProBoost, the heater turns off immediately and the fan runs for another 20 minutes to cool the pump. Specifications Maximum Pumping Speed, Air 80 l/sec Ultimate Vacuum Pressure 0.00002 torr Minimum Back Pump FAD at 60 Hz 2.8 CFM Maximum Discharge Pressure 0.2 torr Ambient Environmental Temp 10–30°C Heat-up time 7 minutes Inlet Connection NW50 Discharge Connection NW25 Silicone Oil Capacity Approximately 30 ml Cool Down Time 20 minutes Pump Dimensions, L x W x H 5.5 x 5.4 x 7.5 in Weight 5.6 lbs (2.5 kg) Download Manual
$5,410.20
Welch DryFast Ultra Diaphragm Pump 2042
Welch DryFast Ultra Diaphragm Pump 2042 This item may carry up to a 5 day lead time. Product Details Chemical Resistant Oil-Free Tuneable Vacuum Welch DryFastTM PTFE Diaphragm Vacuum Pumps enable precise vacuum control for organic evaporations with exclusive Advanced Vapor Management (AVM). Oil-Free, portable, chemical resistant, 2 head diaphragm design simplifies maintenance. Choose from seven dry PTFE vacuum pump models with flows up to 70 L / min and adjustable vacuum down to 2 Torr. Economical DryFastTM vacuum pumps are perfect for tough lab applications. Specifications Model Number 2042 Application Rotary Evaporation/Distillation (lowvolatility solvents <160oC B.P., ~ 2 Liter), Centrifugal Concentrators, Vacuum ovens (mid- size), pumping harsh vapors & gases Type Laboratory Vacuum Pump Free Air Displacement cfm (l/min.) @60Hz 1.2(35) Free Air Displacement m3/hr (l/min.) @50Hz 1.75(29) Ultimate Pressure 2(2.7) Maximum Vacuum 29.85 Motor Horsepower (watts) 1/5(150) Adjustable Vac. / Gas Ballast Yes Tubing Needed 1/4(7) Intake Thread NPT M14(1/8) Overall Dimensions LxWxH in. (cm) 13.8x6.8x8.8(35.2x7.2x22.3) Ship Weight 25(11.3) Shipping Carton Dimensions LxWxH in. (cm) 21x14x15 (52x35x37) Adjustable Vacuum Knob
$6,358.74
True Terpenes Limoncello - Infused
True Terpenes Limoncello - Infused All sales are final. Orders can be refunded prior to fulfillment and shipping but once the order has been fulfilled and/or shipped, no refunds will be issued. Due to the hazardous nature of our product, we are unable to accept returns. (Please Note: This product has 1 week lead time) Named after a delicious sweet liquor this lemon forward strain profile will leave you wanting desert. FRAGRANCE: A strong citrus aroma, but notes of mango, pine and pepper blend into the lemony tang to give this profile a unique nose. A high nerolidol level adds to the floral, fruity green tones. EFFECT: Limoncello will help you unwind at the end of the day with a uplifting peace. CERTIFICATES: COA | SDS | FOOD GRADE Storage Requirements Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. No Smoking. Store below 15℃ (60℉). Improper storage can cause terpenes to degrade. DilutionTerpenes must be diluted prior to use for flavor and effect (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With CareCan cause skin irritation, do not ingest PRIOR to dilution. TRUE GRADE™ It is our promise to you. Our isolated terpenes are triple-distilled making them the cleanest terpenes in the world. Fresh out of the bottle, undiluted, every single one of our products bests the most rigorous consumer safety standards. GMP | ISO-9001:2015 | FSSC 22000 Blended in cGMP facilities adhering to the requirements for a Quality Management System (QMS) specified by ISO 9001:2015 and FSSC 22000 standards. Analyzed Tested and passed True Grade™ safety specifications for residual solvents, pesticides and heavy metals. Stability Tested Rigorously tested with mid-grade distillate against separation, cloudiness and unacceptable levels of color change. We Qualify True Terpenes implements supply-chain control for all raw materials and is proud to provide True Terpenes’ qualification documents such as certificates, licenses and registrations to be qualified as your supplier. Undiluted We do not add PG, VG, PEG, MCT or Vitamin E Acetate to any of our products. Food Grade Manufactured in cGMP facilities using food grade ingredients. UV Protected This product is packaged in a cobalt blue, UV deterrent and food grade bottle with tamper evident seal. Made in the USA Formulated, blended, manufactured and fulfilled in the United States. Refined Isolates This product contains ultra-pure, molecularly-refined terpene isolates. Only the best.
$170.74 - $3,161.81
1/4" Cap
SSP Instrumentation Duolok® tube fittings are designed, manufactured and quality controlled to be totally “interchangeable” with the Swagelok® brand of tube fittings. Component by component examination plainly shows the two brands as completely “componentintermixable.” The precision manufacturing of both products to stringent tolerances under rigid quality control procedures ensures the safety, performance and reliability of service whenever Duolok® and Swagelok® component parts are mixed and used in accordance with published installation and service recommendations. Specifications Connection Type 1 Duolok Tube Fitting Connection Size 1 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Duolok Pressure Rating = Tubing Rating SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA! Dimensions A 0.92 in C 0.70 in D 0.60 in G 9/16 in H 1/2 in T 1/4 in B 0.63 in
$7.03$2.81
Polyscience 10 Liter General Purpose Water Bath
Polyscience 10 Liter General Purpose Water Bath Key Features: Displays actual and set point temperature simultaneously Three push-button pre-sets for frequently used temperatures Integrated timer Hinged gable cover Calibration capability Reservoir sizes from 2 to 28 liters Reservoir made of 304 Stainless Steel Reservoir drain (10 liter and larger baths) Primary and automatic safety thermostats Also compatible with waterless bath beads Specifications Working Temperature Range °F Ambient +10° to 212° Reservoir Capacity (liters) 10 Reservoir/Tank Material Stainless Steel Reservoir Cover Hinged Gable Working Access (L x W x D) (inches) 10.6 x 11.6 x 6 Temperature Stability °F ±0.2° Display 3.25" Flammability Class (DIN 12876-1) I (NFL) Over-Temperature Protection / Failsafe Heater Control Yes Maximum Ambient Temperature °F 104° Overall Dimensions (L x W x H) (inches) 17 x 15.5 x 15.5 Shipping Weight (pounds) 22.0 60Hz Only Part Number WBE10A11B Included Hardware Sample Tray Heater Wattage 1000 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/8.6 Regulatory Approvals ETL Certifications: Regulatory Approvals: ETL Regulatory Approvals: CE
$1,368.71
10L Neocision Dual Head Short Path Distillation Kit
10L Neocision Dual Head Short Path Distillation Kit This unit carries a 2 day lead time. The 10L Neocision Distillation Turnkey Setup features our Dual 10L P5 Distillation Heads and USA made glass. Every component in this turnkey is made for precision, throughput, and repeatable results. Also included the Bullseye Precision Vacuum Gauge from Digivac which is the most rugged and dependable vacuum gauge on the market. You will also receive a Dual Dewar Style Glass Cold Trap to keep all volatiles and solvents out of your vacuum system. This Turnkey Setup gives you everything needed to perform distillation at the highest level. The 10L Neo Kit Includes: 10L Neocision Kit with Dual P5 Distillation Heads KF-25 90 Degree Long Manifold and Metering Valve Dual Dewar Style Glass Cold Trap Bullseye Precision Vacuum Gauge Distillation Quick Start Guide This guide gives basic quick start instructions for distillation systems. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs, Before beginning distillation, ensure the following steps have been taken: Vacuum Pump is in good working order. Pump should be run against dry load to allow internals to warm up. Oil should be clear. Cloudy or dark oil should be changed. All glass components are in good working order and ready to be assembled A winterization and degassing procedure has been done to prepare oil for distillation Once all three of these steps have been completed, you are ready to begin distilling. Begin by placing stir bar in boiling flask and then load your material. This should be done using a funnel. A small amount of alcohol in the oil will give it a thinner consistency making it easier to transfer. Assemble all glassware and ensure each joint is properly greased. Do not use too much, as the vacuum pressure might pull some grease into the system. To ensure a full seal, spread grease in a circular motion by rotating glassware Attach circulator to condenser and set temperature to 50C. Allow circulator to reach temperature before beginning distillation. Connect vacuum pump to manifold. The manifold will allow you to isolate each individual component as well as let atmosphere into and out of the system. Connect receiving cow to cold trap. Connect cold trap to manifold. Connect vacuum gauge to manifold. At this point, ensure all connections are correct. Also ensure receiving cow is positioned to collect the first fraction in the far-left receiving flask. Circulator should be at its set temperature. Turn on vacuum pump to begin process. Turn on heat and set to 60C. Vacuum pump will begin to pull down and temperature will begin to rise. Watch the gauge to monitor vacuum pressure and stability. Start stir slower and increase speed with temperature. Once you are close to 60C, increase the temperature 20 degrees. Continue to raise the heat incrementally in 20-degree steps, increasing the set temperature as you near your set point. Increase temperatures incrementally until you reach 220C. You will see your first fraction somewhere between 180C and 190C or slightly before. This is the “heads” fraction. You will move to your second fraction when you see an increased reaction in the head, a slight color change toward golden, as well as a thickening of distillate. When this fraction hits, allow the distillate to “self-clean” the head for a minute or two then, rotate the cow to the middle receiving flask. Collect your “main body” fraction. You will see temps between 190-220C during this fraction. Continue to increase stirring speed as necessary. Reaction in the head may vary but it should never stop. As fluid level in the boiling flask decreases, increase stir speed. The final “tails” fraction is a mixture of the first and second fractions and should be saved for re-distillation later. Ideally, you want to turn the cow to the final flask before the tails fraction hits. The “tails” fraction has an obvious color change and will be darker than the “main body” fraction. You will see temps between 200-250C during this fraction. As fluid level in the boiling flask decreases even more, set stirring RPM higher (1000+ RPM). You may need to compensate with a bit more heat to finish of the final fraction as well. Once process is complete, stop heat, stop stir, and stop vacuum. Let atmosphere into the system. Be sure to properly store your distillate as exposure to air and light can cause oxidation. ***Note: This entire setup will ship via motor freight.*** *Notice to Customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. BVV™ is not responsible for the failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail, which can cause bodily harm or damage to the surrounding area.
$12,928.27
Glas-Col K Type Thermocouple
Glas-Col K Type Thermocouple Glas-Col K Type thermocouple is used to measure temperatures from -50°C to 1000°C with a lead length of 72" and probe length of either 12" or 18".
$281.05$210.79
Cascade CDO-28 Dry & Decarb Oven
Cascade CDO-28 Dry & Decarb Oven This item carries up to a 2 week lead time. Cascade’s CDO-28 is purpose-built for large-scale, industrial decarboxylation of material with additional features: 28 Cu. Ft. Built-in Humidity Sensor assists in dryness targets Stay in place sliding extension shelves NRTL Certification 6 each FDA & temperature rated fine micron mesh bags for ground material – Mesh bags are required to prevent oven contamination and material loss. This powerful, large capacity forced air laboratory oven uses heated air to remove unwanted compounds from products that are not temperature sensitive. Our ovens feature horizontal airflow that enables more consistent distribution of air. They are designed to have uniform temperatures and airflow across the shelf space from right to left. The CDO-28 includes a built-in humidity sensor and fine micron mesh bags for drying or decarboxylating powders or ground material. Ideal Uses: Industrial scale forced-air convection drying below 149ºC / 300ºF Decarboxylation processes Drying organic material. Drier material will yield better results than processing wet material. Removing as much moisture as possible pre-processing will save time in the post process of vacuum purge and winterization. Lab glassware dryer Model CDO-28 Features Horizontal Airflow. The airflow moves uniformity across the shelf space from right to left Digital set-point control, timer and overtemp failsafe protection Humidity sensor displays relative humidity levels during process Includes 6 sliding, extend and stay in place shelves for ease of loading. Stainless Steel. Includes 6 temp-rated, fine micron mesh bags for easy loading & uniform drying of messy powders, ground up or turbulent materials Fast heat-up: 24 Minutes to 149ºC (300°F) / Uniformity: +/- 2ºC (3.5°F) Stainless steel interior / Food lab grade construction. 301 SST Shelves Triple wall construction meets CE, UL and TUV requirements to keep work-spaces cool. Quality Made in Oregon USA 1 Year Warranty The Cascade Difference Basic forced-air lab ovens are mass-produced and sold by many large scale laboratory equipment distributors. But there are key differences between Cascade and other less costly, often imported lab ovens: Independent Overtemp Failsafe Protection The Cascade Sciences CDO-28 is equipped with a heating cutoff system that will automatically stop power to the heaters when the overtemp setting is tripped. This protection system will provide peace of mind for overnight or unattended drying processing. NRTL Certification. No Extra cost. The CDO-28 Oven comes certified by the Nationally Recognized Test Lab, TUV. This certification is a requirement by many municipalities. CAN/CSA-C22.2 No. 61010-1:2012+UPD No. 1:2015-07 + UPD No. 2:2016-04CAN/CSA-C22.2 No. 61010-2-010:2015UL 61010-1:2012-05UL 61010-2-010:2015EN 61010-1:2010EN 61010-2-010:2014 Rigorous Quality Assurance in an ISO Certified, USA Manufacturing Facility Cascade Sciences manufactures our ovens in Oregon, USA. We are proud of our ISO 9001 Certification/Accreditation. Each oven completes a series of quality assurance procedures before shipment: Electrical & mechanical safety is thoroughly tested in compliance with TUV requirements Functional testing verifies user settable items consistent with most lab protocols/usage models Temperature verification includes calibration & temp chamber uniformity following ASTM standards Units are cleaned and packed in ISTA tested, certified packaging materials Specifications Capacity Volume 28 Cubic Ft. (793 Cubic Liters) Interior 31.5″W x 60.5″H x 26″D 800mm x 1,537mm x 661mm Exterior 43”W x 85.5”H x 34.3”D 1,092mm x 2,171mm x 871mm Temperature Temperature Range 2.2ºC (36°F) above room temp to 148ºC (300°F) Temperature Stability +/- 2ºC (+/-3.5°F) Temp Recovery @ 240°F *Load Dependent* Door Open 30 Seconds: 3 min to stabilize Door Open 60 Seconds: 5 min to stabilize Power 230V – 240V / 1ph / 26AMP Oven Must Be Hardwired By Electrician Oven will also run on 208V BTUs Per Hour at Max Power 18,425 BTUs Air Stats Air Intake Adjustable. Top 2.75” Diameter Air Exhaust Adjustable. Top 2.75” Diameter Linear Shelf Space Airflow 17.1 cubic ft per min Shelving Quantity Included 6 each. Height adjustable. Surface Area 31”W x 23”D (787mm x 584mm) Weight Capacity 75 lbs (34 kg) Mesh Bags Quantity Included Comes with 6 Temp Rated Mesh Bags Dimensions 27.5″W x 21.5″D (699mm x 546mm) Polypropylene (PP) Melt Temperature 161°C (363°F) Softening Point 152°C (305°F) Heat Deflection Temperature 90°C (194°F) Glass Transition Temperature 0°C (32°F) * Mesh bags are REQUIRED to prevent oven contamination and ground material loss. * Polypropylene products produced for some filtration applications are made from resin that complies with FDA regulations for food contact. The regulation compliance is product number dependent / specific. * Impact at cold temperatures is likely to cause strand cracking or breakage Weight Product Weight 565 lbs (256 kg) Shipping Weight 640 lbs (290 kg) Certifications ISO 9001NRTL TUV #U8 170464972 077CAN/CSA-C22.2 No. 61010-1:2012+ UPD No. 1:2015-07 + UPD No. 2:2016-04CAN/CSA-C22.2 No. 61010-2-010:2015UL 61010-1:2012/R:2016-04UL 61010-2-010:2015EN 61010-1:2010EN 61010-2-010:2014 Warranty 1 Year Additional Resources: Download P-Trap Exhaust Tutorial View NRTL Certification
$22,479.74
ULVAC DTC-41 110V 1.6 Cfm 2-Stage Chemical-Duty Diaphragm Pump TUV
ULVAC DTC-41 110V 1.6 Cfm 2-Stage Chemical-Duty Diaphragm Pump TUV Manufactured and imported directly from Japan, ULVAC DTC series diaphragm pumps feature integral forced-air cooling. They have two-stage PTFE diaphragms that are ideal for pumping corrosive gases and organic solvents. These pumps are oil-free, portable, and chemical-resistant, which means less maintenance and no more frequent and costly oil change, or cross contamination. Ai is now the official dealer of ULVAC vacuum pumps. These pumps are made in Japan with one year warranty and technical support from ULVAC. Features: TUV certified to UL and CSA standards Only PTFE components are exposed to vacuum, ideal for pumping corrosive gases and organic solvents Integral forced-air cooling Very compact and portable Designed to back most hybrid turbo pumps Applications: Rotary evaporator Evaporating system Vacuum concentrator Vacuum filtration Vacuum drying systems Medical/pharmaceutical equipments Centrifuge Laser-gas circulation Specifications Model ULVAC DTC-41 Part number 1042840 Electrical requirements 115V 60Hz or 230V 50/60Hz, single phase 0.13HP, 100 watts Full load current 1.1 amps Pumping rate 1.62 cfm (6 minutes to pump down a 0.9 cu ft oven) Gasket material All-PTFE Ultimate vacuum level 7.5 torr / 10 mbar Inlet/Outlet 3/8" hose barb Adjustable vac./gas ballast No Pump dimensions (LxWxH) 13 x 5.5 x 8.5 inches Shipping dimensions (LxWxH) 15 x 9 x 10 inches Pump weight 23 Lb Shipping weight 26 Lb Noise 53 dB(A) Working environment 32°F to 104°F (0°C to 40°C) Compliance TUV certified to UL and CSA standards
$3,112.62 - $3,702.83
Cone Metering Tray
Cone Metering Tray This accessory is a volumetric measuring device that ensures precision and accuracy across your all your cones. This loading platform takes away the guesswork and allows the distribution of a precise amount of .5 grams of material per pre-roll, when going through the filling process. With the Sliding Plate installed on the bottom, the Loader is packed with material to the desired height/weight based on your particular grind consistency. Once the Loader is mounted to top of the Bottom Base the Sliding Plate can be pulled out, in which the material will fall down into the Top platform and loaded into the pre-roll. We offer the metering tray in smaller volume sizes because we recommend packing your load in increments, that way you get that perfect, desired, density, especially at the crutch.
$667.49
SCILOGEX SCI20-S Overhead LED Digital Stirrer, with s/steel cross stirrer, 20L Capacity, 100-220V 50/60Hz, US Plug
SCILOGEX SCI20-S (20L) LED Digital Overhead Stirrer 50-2200rpm SCILOGEX SCI20-S Overhead LED Digital Stirrer, 20L Capacity, 100-220V 50/60Hz, US Plug (including steel cross-stirrer Part# 18900071, stand sold separately) Product Features Buy 1 SCI20-S (20L) LED Digital Overhead Stirrer and get a Steel Cross-Stirrer FREE! A wide range of speed from 50 to 2200rpm Analog speed controls displayed on the LED display Brushless DC motor for long life and maintenance free High torque for viscous medium stirring Safety circuits allow for safe stop function in anti-stall or overload conditions LED screen for monitoring actual speed Over torque protection automatically stops the motor In the event of power loss, the stirrer will resume stirring at the preset speed when the power returns Pass through stirrer rods accepted Keyless chuck Multi voltage 110-220V cTUVus approved for UL and CSA 2 YEAR WARRANTY Product Specifications Maximum stirring capacity 20L Maximum torque 40Ncm Viscosity maximum 10000mPas Speed range 50-2200rpm Speed display accuracy ± 50rpm Speed display resolution ± 10rpm Chuck diameter range 0.5-10mm Dimensions 3.3W x 8.7H x 7.3Dinches Motor rating input 60W Motor rating output 50W Weight 5.5lbs Motor type brushless DC motor Voltage/Power 110-220V, 50/60 Hz/ 70W Speed/Torque display LED Overload protection display LED lights Protection class IP42 Permissible ambient temperature and humidity IP42 Additional Resources and Information Downloadable PDFs SCI20-S Manual Scilogex OverheadStirrers Brochure Scilogex OverheadStirrers Software SCILOGEX SCI20/40-S LED Digital Overhead Stirrer.mp4 from SCILOGEX on Vimeo.
$969.62
The Press Club 2" x 9" ROSIN BAGS
2" x 9" Rosin Bags The Press Club brings science to the art of rosin pressing. The Press Club prides themselves in making the toughest and strongest rosin bags on the market. After years of research and lab testing, all our rosin bags are now made with our proprietary pink stitch and come with a ZERO BLOWOUT GUARANTEE™. If you ever get one, they will replace the bag. It's that simple. Available in 25, 37, 50, 75, 90, 120, 160 and 220 micron. 2.5” x 9” Inch 25-Pack Pre-Flipped Inside-Out 100% Food-Grade Nylon Solvent & Boil Resistant High Pressure Resistance (Over 20 Tons) High Heat Resistance (Up To 375° F) Reusable Over 5x (Simply Wash With Alcohol) Covered By The Press Club’s Zero Blowout Guarantee Satisfaction Guarantee & 365-Day Return Policy Made In USA General Micron Guideline: Dry Sift & Bubble (5, 10, 15, 25, 37, 50) | Flower (75, 90, 120, 160, 220)
$42.09
The Press Club 3" x 6" ROSIN BAGS
3" x 6" Rosin Bags The Press Club brings science to the art of rosin pressing. The Press Club prides themselves in making the toughest and strongest rosin bags on the market. After years of research and lab testing, all their rosin bags are now made with their proprietary pink stitch and come with a ZERO BLOWOUT GUARANTEE™. If you ever get one, they will replace the bag. It's that simple. Available in 25, 37, 50, 75, 90, 120, 160 and 220 micron. 3” x 6” Inch 25-Pack Pre-Flipped Inside-Out 100% Food-Grade Nylon Solvent & Boil Resistant High Pressure Resistance (Over 20 Tons) High Heat Resistance (Up To 375° F) Reusable Over 5x (Simply Wash With Alcohol) Covered By The Press Club’s Zero Blowout Guarantee Satisfaction Guarantee & 365-Day Return Policy Made In USA General Micron Guideline: Dry Sift & Bubble (5, 10, 15, 25, 37, 50) | Flower (75, 90, 120, 160, 220)
$35.06
Welch BTpro100
Welch BTpro100 Welch’s BTpro vacuum pump series has a flow and vacuum level to provide fast performance for your size of rotary evaporator, glass reactor, purge oven, or winterization filtration apparatus.These chemical duty PTFE diaphragm pumps are oil-free. The pumping action and deep vacuum comes from the movement of PTFE diaphragms within PTFE heads. All wetted services in the flow path are made of fluoroplastic making the BTpro pump highly chemically resistant. As a result, the BTpro vacuum pump series is near-zero maintenance. A cold trap placed in-line with BTpro pump is needed if terpenes are part of the flow path. Model BTpro100 Free Air Displacement@60Hz,lpm(CFM) 100(3.5) Ultimate Vacuum Pressure, Torr 6 Maximum Vacuum, in. Hg 29.7 Horsepower, HP (watts) 0.5(390) Built-in adjustable vacuum - Gas Ballast Yes Head Material PTFE Diaphragm PTFE Inlet/outlet Connection NW16 flange1 Agency (National Recognized Lab) cUL Weight, lbs (kg) 40.3(18.3) Overall DimensionsLxWxH in.(cm) 9x15x7(23x38x18) Shipping Weight, lbs(kg) 48.5 (22) Shipping Carton DimensionsLxWxH in.(cm) 18.9x12.6x11.8(48x32x30)
$6,815.45$6,429.01
Welch BTpro70
Welch BTpro70 ***Note: This item has a possible lead time of 2-3 weeks depending on stock availability.*** Welch’s BTpro vacuum pump series has a flow and vacuum level to provide fast performance for your size of rotary evaporator, glass reactor, purge oven, or winterization filtration apparatus. These chemical duty PTFE diaphragm pumps are oil-free. The pumping action and deep vacuum comes from the movement of PTFE diaphragms within PTFE heads. All wetted services in the flow path are made of fluoroplastic making the BTpro pump highly chemically resistant. As a result, the BTpro vacuum pump series is near-zero maintenance. A cold trap placed in-line with BTpro pump is needed if terpenes are part of the flow path. The BTpro40 and BTpro70 models employ patented valve and diaphragm technology that generates a deep 15 Torr vacuum pressure with each PTFE head. In addition, both pump models have built-in tuneable vacuum to control evaporation rate. The tunable vacuum adjustment can also be used to stop accidental bumping/foaming. Model BTpro70 Free Air Displacement@60Hz,lpm(CFM) 70(2.5) Ultimate Vacuum Pressure, Torr 15 Maximum Vacuum, in. Hg 29.3 Horsepower, HP (watts) 1/5(150) Built-in adjustable vacuum Yes Gas Ballast - Head Material PTFE Diaphragm PTFE Inlet/outlet Connection 3/8” barb Agency (National Recognized Lab) CSA Weight, lbs (kg) 21.3(9.6) Overall Dimensions LxWxH in.(cm) 13.8x6.8x8.8 35x17x22 Shipping Weight, lbs(kg) 25 (11.3) Shipping Carton Dimensions LxWxH in.(cm) 21x14x15 (52x35x37)
$4,215.74$3,513.12
Welch BTpro40
Welch BTpro40 (CSA) Certified ***Note: This item has a possible lead time of 2-3 weeks depending on stock availability.*** Welch’s BTpro vacuum pump series has a flow and vacuum level to provide fast performance for your size of rotary evaporator, glass reactor, purge oven, or winterization filtration apparatus. These chemical duty PTFE diaphragm pumps are oil-free. The pumping action and deep vacuum comes from the movement of PTFE diaphragms within PTFE heads. All wetted services in the flow path are made of fluoroplastic making the BTpro pump highly chemically resistant. As a result, the BTpro vacuum pump series is near-zero maintenance. A cold trap placed in-line with BTpro pump is needed if terpenes are part of the flow path. The BTpro40 and BTpro70 models employ patented valve and diaphragm technology that generates a deep 15 Torr vacuum pressure with each PTFE head. In addition, both pump models have built-in tuneable vacuum to control evaporation rate. The tunable vacuum adjustment can also be used to stop accidental bumping/foaming. Model BTpro40 Free Air Displacement@60Hz,lpm(CFM) 40(1.4) Ultimate Vacuum Pressure, Torr 15 Maximum Vacuum, in. Hg 29.3 Horsepower, HP (watts) 1/5(150) Built-in adjustable vacuum Yes Gas Ballast - Head Material PTFE Diaphragm PTFE Inlet/outlet Connection 3/8” barb Agency (National Recognized Lab) CSA Weight, lbs (kg) 15.0(6.8) Overall DimensionsLxWxH in.(cm) 12x7x8.3(31x18x22) Shipping Weight, lbs(kg) 19(8.6) Shipping Carton DimensionsLxWxH in.(cm) 21x14x15(52x35x37)
$2,613.76$2,388.92
Welch WOB-L Pump 2546
Welch WOB-L Pump 2546 Product Details Economical Oil Free Adjustable Vacuum / Pressure Reliable WOB-L Piston pumps are perfect for many common laboratory vacuum applications. Features: Vacuum and Pressure - to 60 Torr (27.6"Hg). Includes Vacuum and Pressure Regulators and Gauges - simple to adjust and monitor vacuum level and delivery pressure. Inlet Water Trap - float ball rises to seal off pump from accidental ingestion of water. Muffler quiets pump and filters discharge air. For use with dry or aqueous vapor applications only. Specifications Model Number 2546 Application Filtration (1 to 6 funnels), Aspiration, Desiccation, SPE, Replace water aspirator, Vacuum Drying Type Laboratory Vacuum Pump Free Air Displacement cfm (l/min.) @60Hz 1.6(45) Free Air Displacement m3/hr (l/min.) @50Hz 2.3(38) Ultimate Pressure 60(80) Maximum Vacuum 27.6 Max Pressure PSIG (pascal) 100(106) Motor Horsepower (watts) 1/4(190) Adjustable Vac. / Gas Ballast Yes Tubing Needed 3/16(5) Intake Thread NPT 1/4 Overall Dimensions LxWxH in. (cm) 10x7.5x9 (25.4x19.1x7.7) Ship Weight 17(7.7) Shipping Carton Dimensions LxWxH in. (cm) 15.3x12.3x12.7 (39x31x32) Intake Catch Jar Yes Exhaust Catch Jar Yes Adjustable Vacuum Knob Adjustable Pressure Yes Vacuum Gauge Dial Pressure Gauge Dial
$1,440.38
Vacuubrand MD 1C Chemistry Diaphragm Pump
Vacuubrand MD 1C Chemistry Diaphragm Pump Chemistry diaphragm pump in action Three-stage chemistry-design diaphragm pumps are an excellent solution for continuous, oil-free pumping of corrosive gases and vapors and meet high requirements regarding ultimate vacuum. The three-stage construction provides the advantageous combination of high pumping speed and deep ultimate vacuum in a pump with a very small footprint. All parts in contact with pumped media are made of chemically resistant fluoroplastics. Well-proven PTFE sandwich diaphragms increase reliability and extend operating life. The MD 1C with gas ballast valve is optimally prepared for pumping easily condensable vapors (high boiling solvents). Three-stage chemistry diaphragm pumps are an excellent solution for applications involving corrosive gases and vapors at high vacuum requirements. Typical applications are vacuum generation at rotary evaporators, vacuum concentrators and many other laboratory applications. Due to their excellent ultimate vacuum they are the ideal solution for evaporation of high boiling solvents even with gas ballast. The MD 1C pump is the heart of a whole line of reliable chemistry pumping units. Performance features: outstanding chemical resistance and superior vapor tolerance exceptionally high performance even at low vacuum excellent ultimate vacuum even with gas ballast whisper quiet and ultra-low vibration proven long diaphragm life, maintenance-free drive system Technical Data Max. pumping speed 50 Hz 1.3 m3/h Max. pumping speed 60 Hz 0.88 cfm Ultimate vacuum 2 mbar / 1.5 torr Ultimate vacuum with gas ballast 4 mbar / 3 torr Number of heads 4 Number of stages 3 Lower ambient temperature (operation) 10 °C Upper ambient temperature (operation) 40 °C Lower ambient temperature (storage) -10 °C Upper ambient temperature (storage) 60 °C Max. back pressure (abs.) 1.1 bar Anschluss saugseitig Hose nozzle DN 8-10 mm Outlet connection Hose nozzle DN 8 mm Rated motor power 0.08 kW Rated motor speed at 50/60 Hz 1500/1800 min-1 Protection class IP 40 Dimension L in mm 316 mm Dimension W in mm 143 mm Dimension H in mm 175 mm Weight 6.9 kg Noise level at 50 Hz, typ. 45 dBA Rated mains voltage range 1 200-230 V Mains frequency 1 50-60 Hz Brochure
$5,691.25
So-Low -85°C Ultra-Low Upright Freezer - 25 Cubic Ft.
So-Low -85°C Ultra-Low Upright Freezer - 25 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! So-Low Ultra-Low Upright Freezers are second to none in low temp applications to suit any laboratory or application needs. These Ultra-Low Temp freezers feature digital temperature control with 2 temperature displays. One shows the set temperature and the other shows the actual temperature in the freezer. The So-Low U85-25 features a battery operated alarm system that will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Product Specifications Temperature Control Touch Screen Control Displays set point and chamber temperature Hi/Low Alarm Relay Dry Contacts Power Failure Dry Contacts Battery Back-up Viewable Temperature graph Data logging downloadable via USB or FTP Multi-Level Security VNC Remote Access via PC / smart devices Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing feature. Dimensions: Exterior: 50" x 37" x 79.5" Interior: 34" x 25" x 51.25" Capacity 25 Cubic Ft. / 710 Liters Temperature Range -40°C to -85°C / -40°F to -121°F Shelving 4 Adjustable Shelves (5 Compartments) Inventory Rack Capacity 30 Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Access Port Mounted in left hand side of the cabinet will be a 1/2" porthole leading into the chilling chamber, complete with plugs. Refrigeration System So-Low cascade type. Two hermetic motor compressors. These compressors are the heavy duty industrial type: air cooled. The motors are sealed in oil for life and have thermoguard overload protection. Compressors start in sequence to protect the unit from overloading. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$17,284.54
So-Low -80°C Ultra-Low Chest Freezer - 27 Cubic Ft.
So-Low -80°C Ultra-Low Chest Freezer - 27 Cubic Ft. Please note: This Product may carry up to an 8 week lead time! So-Low Ultra-Low Chest Freezers are second to none in low temp applications to suit any laboratory or application needs. These Ultra-Low Temp freezers feature digital temperature control with 2 temperature displays. One shows the set temperature and the other shows the actual temperature in the freezer. The So-Low C80-27 features a battery operated alarm system that will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Product Specifications Temperature Control Digital Control with two temperature displays. One display shows the set temperature, the other shows the actual temperature in the freezer. Alarm System Battery operated alarm system will emit an audible and visual signal when there is a mechanical or electrical failure. The alarm has an over and under temperature setting, alarm silencing switch, and battery test switch. Dimensions: Exterior: 98" x 36" x 43.5" Interior: 67" x 23" x 31.25" Capacity 27 Cubic Ft. / 766 Liters Temperature Range -40°C to -80°C / -40°F to -112°F Shelving N/A Inventory Rack Capacity 48 Remote Alarm Relay A relay for a remote alarm hook-up is also provided. Refrigeration System So-Low cascade type. Two hermetic compressors. CFC & HCFC free refrigerants. Construction Chamber is 14-ga. zinc coated galvanized steel. Exterior is 16-ga. steel. Powder coated cool gray finish. Voltages Available 115/60/1 - 220/50/1 Technical Support Supplied by Nation-Wide-Network of service companies. ETL Electrical Approval Specification Data Sheet Diagram Data Sheet
$23,882.18
Scilogex DS-500 Homogenizer Probe
Scilogex DS-500 Homogenizer Probe (Probe ONLY - Motor NOT Included) This is the Scilogex DS-500 Homogenizer probe with either coarse teeth for solid/liquid media or fine slot teeth for Water in Oil/Oil in Water emulsions both probes are good for volumes from 10-5000ml and will attach to the D500 drive motor. Each probe is 20mm in diameter and has a 215mm immerse length with flat head-open slots. DS-500/5 generator 5mm dia. generator, flat head-open slot, 60mm immerse length for solid/liquid media, volumes 1-50ml Slot Type Specifications: Probe Slot Type Specifications Model # Slot Type Media Type DS-500/1 Flat Head-Open COARSE Solid/Liquid DS-500/2 Flat Head-Open FINE Water in Oil/Oil in Water Emulsions DS-500/5 Flat Head-Open slot Solid/Liquid medium,
$1,129.82 - $1,298.45
Polyscience 7 Liter Refrigerated Circulator, -40°C
Polyscience 7 Liter Refrigerated Circulator, -40°C ***Note: This item has a lead time of 2-3 weeks depending on stock availability.*** Description: -40, 7 L Ref Circulator Controller Type: Advanced Digital Display: 3.75" Touch-Pad LCD Connectivity: Ethernet, USB A & B, RS232/addressable RS485, External Temperature Probe Languages Supported: 4: French, German, Spanish, English Swivel 180 Rotating Controller: Yes Working Temperature Range °C: -40° to 200° Temperature Stability °C: ±0.01° Fluid Optimization/Specific Heat Tuning: Automatic and/or user-adjustable Temperature Calibration Capability: 1- point Working Access (L x W x D) (cm): 15.7 x 14.2 x 12.7 cm Pump Type: Pressure/Suction External Temperature Control Capability: Yes Flammability Class (DIN 12876-1): III (FL) Specifications Working Temperature Range °F -40° to 392° Working Temperature Range °C -40° to 200° Nominal Cooling Capacity @ +20C (W) 360 Reservoir Capacity (gallons) 1.85 Reservoir Capacity (liters) 7 Reservoir/Tank Material Stainless Steel Reservoir Cover Included DuraTop Yes LidDock LidDock Cleanable Air Filter Yes Working Access (L x W x D) (inches) 6.18 x 5.59 x 5 in Working Access (L x W x D) (cm) 15.7 x 14.2 x 12.7 cm Temperature Stability °F ±0.02° Temperature Stability °C ±0.01° Display 3.75" Touch-Pad LCD Display Resolution (Set) 0.01 Display Resolution (Read) 0.01 Pump Type Pressure/Suction Pump Speed Variable Process Connections 1/4" (F) NPT External Temperature Control Capability Yes Flammability Class (DIN 12876-1) III (FL) Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes WhisperCool Environmental Control Technology Yes Cool Command Refrigeration Technology Yes Reservoir Drain Yes Included Software PolyTemp Viewer, USB driver Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 21.3 x 8.7 x 24.3 in Overall Dimensions (L x W x H) (cm) 54.1 x 22.1 x 61.7 cm Refrigerant R404A Environmental Compliance RoHS, WEEE Shipping Weight (pounds) 90.0 Shipping Weight (kilograms) 40.8 60Hz Part Number AD07R-40A11B Maximum Pressure (psi) 4.3 Maximum Pressure (bar) 0.30 Maximum Pressure Flow Rate (gpm) 5.30 Maximum Pressure Flow Rate (l/min) 20.1 Maximum Suction Flow Rate (gpm) 3.9 Maximum Suction Flow Rate (l/min) 14.7 Cooling Capacity @ -20°C (W) 115 Cooling Capacity @ 0°C (W) 250 Cooling Capacity @ +20°C (W) 360 Included Hardware Nylon hose adapters for 3/8", 1/4", and 3/16" Heater Wattage 1100 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/12 Regulatory Approvals ETL
$7,376.14
Polyscience 7 Liter Standard Digital Refrigerated Circulator (-20°C/170°C)
Polyscience 7 Liter Standard Digital Refrigerated Circulator (-20°C/170°C) ***Note: This item has a possible 2-3 week lead time depending on stock availability.*** Specification Description -20, 7 L Ref. Circulator Controller Type Standard Digital Display 3.75" Touch-Pad LCD Connectivity RS232 Swivel 180 Rotating Controller Yes Working Temperature Range °C -20° to 170° Temperature Stability °C ±0.04° Fluid Optimization/Specific Heat Tuning Automatic Temperature Calibration Capability 1-point Working Access (L x W x D) (cm) 15.7 x 14.2 x 12.7 cm Pump Type Pressure Flammability Class (DIN 12876-1) I (NFL) Working Temperature Range °F -4° to 338° Working Temperature Range °C -20° to 170° Nominal Cooling Capacity @ +20C (W) 200 Reservoir Capacity (gallons) 1.85 Reservoir Capacity (liters) 7 Reservoir/Tank Material Stainless Steel Reservoir Cover Included DuraTop Yes LidDock Yes Cleanable Air Filter Yes Reservoir Liquid Level Indicator Yes Working Access (L x W x D) (inches) 6.18 x 5.59 x 5 in Working Access (L x W x D) (cm) 15.7 x 14.2 x 12.7 cm Temperature Stability °F ±0.08° Temperature Stability °C ±0.04° Display 3.75" Touch-Pad LCD Display Resolution (Set) 0.1 Display Resolution (Read) 0.1 Pump Type Pressure Pump Speed Two Process Connections 1/4" (F) NPT Flammability Class (DIN 12876-1) I (NFL) Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes Reservoir Drain Yes Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 21.3 x 8.7 x 24.3 in Overall Dimensions (L x W x H) (cm) 54.1 x 22.1 x 61.7 cm Refrigerant R134a Environmental Compliance RoHS, WEEE Shipping Weight (pounds) 90.0 Shipping Weight (kilograms) 40.8 Catalog Page Number 42-43 60 Hz Only Part Number SD07R-20-A11B Maximum Pressure (psi) 3.5 Maximum Pressure (bar) 0.24 Maximum Pressure Flow Rate (gpm) 2.90 Maximum Pressure Flow Rate (l/min) 11.0 Cooling Capacity @ -20°C (W) 30 Cooling Capacity @ 0°C (W) 120 Cooling Capacity @ +20°C (W) 200 Cooling Capacity @ +100°C (W) 200 Included Hardware Nylon hose adapters for 3/8", 1/4", and 3/16" Heater Wattage 1100 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/12 Regulatory Approvals ETL Key Features: Large, universal icon and English display Swivel 180™ Rotating Controller On-board connectivity: RS-232 serial output On-screen prompts Automatic performance optimization Single-point calibration capability Operator's Manual
$5,564.78
V2 Rosin Press 4x7 Bundle with Hydraulics
V2 Rosin Press 4x7 Bundle with Hydraulics Description The last press you buy: Period. We designed this press with your space and portability constraints in mind. All the while, creating a system that will last you a lifetime. We kept the pressure options entirely open source so you can select the press style that works for you. For more budget friendly options, a simple $40 bottle jack can be used. If you want the best of the best, we carry High End BVA and SPX Hydraulics which come assembled, bled, and tested with pressure gauges installed. Our unique modular design makes any possible electronic warranty work extremely cheap to ship for fulfilment. Our competitors make you ship an entire press in for a simple electronic component failure or loose wire which can cost you hundreds in shipping fees. The Lowtemp V2 is the final solution to any large scale solventless lab. One operator can use up to 5 presses at once via a single pump. THAT'S UP TO 750G PER PRESS!! Running smoothly, a single operator can prep, press, and collect up to 18,000 grams or 40lbs of bubble/sift in an 8 hr shift. Specs Sturdy and Ultra Compact design. 10" tall, 10" long, 6" wide 58 lbs Complete Modular design Food Grade Anodized and insulated 4"x7" plates Powder coated steel Made in Denver, Colorado with Certified American alloys Lifetime Warranty on the press 1 year full warranty on the electronics Universal force options up to 20 tons Horizontal pressing capabilities This product includes: 4"x7" Lowtemp Press backed with our Lifetime Warranty Top and bottom legs (used to bolt the press to the table or used to turn press horizontally) 110v Electronic controller with 2 powerful 200w heating elements Mounting hardware to secure the legs to the press and the press to the table FREE shipping via UPS Ground. Options: Press only: This option is for customers who already own a Lowtemp Plate or Cage kit, upgrading to our new Lowtemp Press with their current controller and adding their own hydraulics. All mounting accessories and hardware included. 4" taller to support bottle jacks. Press with Controller: This option includes the Lowtemp Press with Controller. This is a full kit, which allows you to add your own bottle jack ($40). Great for high quality, portable, reliable, budget builds! This system's structure support rods are 4" longer to fit bottle jacks. Press with Controller and Standard Compact BVA Hand Pump: This solution is out of the box, plug and play. All hydraulics come assembled, bled, and tested. Includes a 20 ton low profile BVA cylinder, ultra compact 2 speed aluminum pump, pressure gauge included. **Option to upgrade for +$250 to our premium, high flow BVA P1000 pump. This features more travel per stroke and a longer handle for extra leverage. Ideal for high workloads** Press with Controller and BVA Air pump: Requires an Air compressor. The pump is technically a foot pedal that is operated by stepping on a pedal, but can also be operated by hand pressure. 20 ton low profile cylinder, pressure gauge included. Press with Controller and SPX Electric pump: Fully automated Electric over hydraulic system with very little noise. Great for large scale operations or anyone looking for a press to run itself at the touch of a button. 20 ton low profile cylinder, pressure gauge included. Additional Options Already own a set of our 3x5 or 4x7 plates/cage? Purchase our press without a controller to save some money. The controllers are the exact same! We will still include all hardware, legs, etc with the press. If you choose to include a High End hydraulics kit, the components will come assembled. These kits consist of a low profile 20 ton cylinder, pump of your choice, hose, all necessary couplings, and a pressure gauge. NOTE: All color options are Limited Edition, and subject to quick stock changes. We will do everything possible to fulfill the color choice you choose, however they can cycle quickly. This product cannot be shipped to a PO Box due to it's size/weight. For Domestic 48 state orders, we ship UPS or Fedex, which won't deliver to a PO Box.
$1,932.21 - $4,714.60
$317.59
Pump Part - MVP - 60 PSI, 150 PSI, Liquid, XL150 - CO2 Regulator
Pump Part - MVP - 60 PSI, 150 PSI, Liquid, XL150 - CO2 Regulator All sales final
$618.31
You have seen 288 out of 682 products