All products
BVV Compression 12" Tri-Clamp x (3) 2" Tri-Clamp x (2) 3/8" Compression x 1/4" Compression x 1/2" Compression Hemispherical Lid
BVV Compression 12" Tri-Clamp x (3) 2" Tri-Clamp x (2) 3/8" Compression x 1/4" Compression x 1/2" Compression Hemispherical Lid This End Cap comes with (4) Compression connections and (3) 2" Tri-Clamp ferrules welded to the end cap with a sanitary weld with a 3" Tube Extension Below the Lid. They allow the user to adapt and connect a tube stub connection to the (1) 1/4", (2) 3/8", and (1) 1/2" port on a Tri-Clamp lid and the Tri-Clamp Connections. These 7 connections are welded on a 12" Hemispherical Tri-Clamp End Cap. Specifications Material: 304 Stainless Steel Connection Types: (3) 2" Tri-Clamp with 3" Tube Extension Below Lid on Center Tri-Clamp Port 12" Tri-Clamp (1)1/4", (2) 3/8" and (1)1/2" Female Compression Connections Standard: 3A
$595.57
4" Wiped Film Evaporator (WFE) Distillation Turn Key System - USA MADE
4" BVV Wiped Film Evaporator This system has a 1-2 week lead time. The BVV™ 4" Wiped Film Evaporator (WFE) is a full turnkey distillation kit that will will allow anyone to run a molecular distillation. With the magnetically driven wiper and high vacuum seals this system is able to achieve vacuum levels below 10 mtorr. The system has multiple temperature control apparatuses that allow the user to dial in specific settings that works best for their application. The maximum operating temperature of the outer jacket is 200°C with the standard circulators shown below. The maximum feed rate is up to 7LPH. On average, you can expect to flow 500-1000ml per hour. All heated circulators can be tailored to your specific needs, just ask our team of experienced account representatives! The temperature controlled circulators will need thermal fluid that corresponds with the temperatures needed. Click here to browse fluids. *Heating and Chilling Fluids are not included* Duratherm S - 7 Gallons - Bottom heater (wiper body) Therminol XP Heat Transfer Fluid - 5 Gallons - Top and middle heater *Propylene Glycol - 5 Gallons - Fluid for the diffusion pump option chiller. Ethanol 99% or Isopropyl 99% - 2 Gallons - Cold Trap / Cold Finger. For a full list of ancillary equipment included in the kits please see the table below: KIT Part of System Component Electrical Requirements (V / Ph / A) WFE04-TK-01 Standard Model Wiper Assembly BVV™ Stirring motor 120V / 1Φ Vacuum System BVV™ Pro Series 35.3CFM Rotary Vane Vacuum Pump* DigiVac Bullseye Precision Vacuum Gauge 220V / 3Φ AA Batteries (4x) Temperature Controlled Circulators Polyscience 7L Polyscience 15L (2x) 120V / 1Φ / 10A 220V / 1Φ / 10A Injection Beaker and Wrench 7LPH Peristaltic Heated Hose 120V / 1Φ 120V / 1Φ WFE04-TK-02 Upgraded Vacuum System Upgraded Cold Trap Wiper Assembly BVV™ Stirring motor 120V / 1Φ Vacuum System BVV™ Pro Series 35.3CFM Rotary Vane Vacuum Pump* Summit Research Diffusion Pump (SR-DP04A)** DigiVac Bullseye Precision Vacuum Gauge 220V / 3Φ 180/264V / 1Φ / 10.5A AA Batteries (4x) Temperature Controlled Circulators Polyscience 7L Polyscience 15L (2x) 120V / 1Φ / 10A 220V / 1Φ / 10A Injection Beaker and Wrench 7LPH Peristaltic Heated Hose 120V / 1Φ 120V / 1Φ Cold Trap Polyscience IP100 120V / 1Φ / 11.5A WFE04-TK-03 Upgraded Vacuum System Upgraded Cold Trap Outlet Pumps Wiper Assembly BVV™ Stirring motor 120V / 1Φ Vacuum System BVV™ Pro Series 35.3CFM Rotary Vane Vacuum Pump* Summit Research Diffusion Pump (SR-DP04A)** DigiVac Bullseye Precision Vacuum Gauge 220V / 3Φ 180/264V / 1Φ / 10.5A AA Batteries (4x) Temperature Controlled Circulators Polyscience 7L Polyscience 15L (2x) 120V / 1Φ / 10A 220V / 1Φ / 10A Injection Beaker and Wrench 7LPH Peristaltic Heated Hose 120V / 1Φ 120V / 1Φ Cold Trap Polyscience IP100 120V / 1Φ / 11.5A Outlet Pumps Beaker and Wrench Gear Pump (2x) Beaker and Wrench Heat Pad PID Controller 120V / 1Φ 120V / 1Φ Notes: *The Rotary vane vacuum pump paired with this kit uses 3Φ power, a smaller single phase pump can be substituted if needed. Substitution will have an impact the performance versus the standard unit. **The Summit Research diffusion pump must be water cooled, if facility water cooling is not an option an additional chiller may be needed, a Polyscience 1HP Durachill is recommended. An air cooled diffusion pump can be provided as a substitute. Substitution will have an impact the performance versus the standard unit.
$64,579.43 - $109,067.47
Replacement PID 3.2TS and 7.5TS
Replacement PID 3.2TS and 7.5TS Specifications SKU FCT30L0-E-F Temperature Range: 32°F - 212°F Dims/weight 4.5 x 4.5 x 4 / 1lb Timer Range 0 -999 Built in Calibration: Yes Temp Display Mode For C Compatible Ovens 32TSO - 32TSB- 75TSO - 75TSB Temperature Accuracy +/- 1°F
$373.13
Cascade 20L Bead Bath with 15L Lab Armor Beads
Cascade 20L Bead Bath Bye-Bye Water Bath! Traditional water baths are associated with messy condensation and the growing of harmful germicides. Cascade Sciences Bead Baths are the next generation of a decades-old lab bath technology. With the included thermal beads, this 20L Cascade Bead Bath operates in a constant, stable, broad temperature range between -80°C to +180°C. The bath itself delivers exceptional temperature uniformity up to 80°C. Zero Evaporation Saves Energy In a water bath, the water is constantly evaporating. As water evaporates, it cools. Because evaporation has a cooling effect, a water bath must heat more frequently. A bead bath uses 4X less energy when set to 65°C and 2X less energy at 37°C. The bead bath also provides more constant temperature with fewer temperature fluctuations during operation. Cascade Sciences Bead Baths and Thermal Beads and Made in the USA and NRTL Certified Cascade Sciences Bead Bath Features: High Thermal Efficiency Microbial/Biofilm Resistant Cross-Contamination Resistant Minimal Cleaning No Refilling No Rack or Accessory Needed Angled Incubation Possible Constant Volume – No Evaporation Non-Corrosive Compatible with non-water tight vessels Independent build-in over-temp, burn-out protection No Warm Up Mobile or Field Use Compatible Non-Combustible Thermal Beads Replace Water and Ice Lab Armor™ Thermal Beads are small, dry, metallic thermal beads designed to replace water in laboratory water baths and ice in ice buckets. Their high thermal conductivity technology is patented and improves energy efficiency of standard water baths by over 50%. Improve lab cleanliness when using thermal beads in place of fluid in water baths. Thermal Beads – Recyclable Lab Armor™ Thermal Beads are formed from solid recyclable metal. The raw material used in Lab Armor™ Beads can be reused in other products. Lab Armor™ Thermal Bead Features: Metal composition with smooth round surface Moisture and gas impermeable High thermal conductivity Working temperature range is -80°C to 180°C Non-toxic, non-vaporizing material Recyclable! Multiple uses – ice replacement Frequently Asked Questions Are Lab Armor™ beads autoclavable?They are not. The steam and pressure ruins the surface of the beads. We recommend a dry heat sterilization: 180°C for 2.5 hours. For a quick touch-up we recommend spritzing with 70% ethanol and stirring. If some debris falls into the beads we recommend placing them in a pail with water and a small about of Dawn, rinsing out multiple times, and then putting through the dry heat sterilization process. How long can I use Lab Armor™ Beads under normal conditions?Under normal conditions, Lab Armor™ Beads should last the life of the bath. If used incorrectly or if not maintained and cleaned properly, the surfaces of Lab Armor™ Beads can become damaged. We recommend that you avoid strong detergents, acids and bases. Bleach, for instance, may tarnish the surface of the Lab Armor™ Beads, reducing its fluidity and overall performance. Can Lab Armor™ Beads be used as an ice bath?There are a number of different ways to use thermal beads. Many customers place containers of beads in their refrigerators, incubators and ovens. When creating an ice bath, be sure to keep the beads dry. We recommend separating the beads from the ice packs, which accumulate condensation. Some kind of mesh wire or fabric helps with this as well. Also, any condensation that builds on the surface of the beads will be able to drip through the mesh. It’s important to keep the beads from soaking in water for extended periods of time. Besides attracting contamination, excessive water contact will tarnish the surface of the Beads and reduce the fluidity of the bath. Also, as an alternative to ice packs, dry ice can be used to make a colder bath (<0ºC).
$4,951.09
16CF BVV™ Neocision ETL Lab Certified Vacuum Oven
16CF BVV™ Neocision Certified Lab Vacuum Oven, 5 Individually Heated Shelves, LED's - 3 Year Warranty Disclaimer: This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in well-ventilated areas! Introduction Our vacuum ovens are purpose-built to perform degassing / purging of light hydrocarbon solvents. Using the technique of cold boiling, the oven applies a gentle heat under reduced pressure conditions to expedite solvent degassing while simultaneously preserving color, aroma, and overall solute quality. We've applied our extensive vacuum expertise and industry experience to produce a series of ovens designed exactly for your needs: low consumption, high-throughput, and reliable operation. Performance Capabilities At Best Value Vacs, we make every effort to provide oven performance capabilities in a standardized format. We're not interested in juking our stats to make a sale. Instead, our goal is to provide quality, transparent production capabilities that meet the demands of our professional customers. Temperature Stability: ±1.0° Temperature Uniformity: within 4% of the temperature setpoint. Heat-Up Time: 30 minutes. Ultimate Vacuum: <500 µmHg / mTorr / micron. Time to Vacuum: 10 minutes to 29"Hg using our 12CFM Spark Free Vacuum Pump Vacuum Hold: guaranteed to lose less than 1"Hg (25.4 torr) in 24 hours. Technical Data Electrical Voltage 120V Frequency 60Hz Power 2000W Current 20A Plug NEMA 5-15 Internal Chamber Heating Individual direct-heat shelves Chamber Material Stainless Steel Dimensions (LxWxH) 25.5" x 32" x 34" Vacuum Gauge Style Glycerin-filled for accuracy and longevity Range (units) -30 to 0 (inHg) / -1 to 0 (bar) Shelving Ships With 8 Shelves Shelf Dimensions (LxW) 24.75" x 31.5" Shelf Capacity 780 in^2 Total Shelf Capacity 6240 in^2 Safety Seal Silicone on Tempered Glass Window Dimensions (LxH) 29.25" x 32" Lights 4 strips of LEDs provide a clear, bright view of the interior Handle No plastic, all metal parts for lifetime durability Exterior Dimensions (LxWxH) 37.25" x 45" x 46" Weight 500lbs Support Locking Casters Safety Electrical Built-in, resettable, overcurrent circuit breaker Thermal Automatic overtemperature shutoff Compliance CE CE Listing Recognized ISO ISO 9001:2015 ETL Certified Conforms to ANSI/UL STD.61010-1, 61010-2-010 -- Certified to CAN/CSA STD. C22.2 NO.61010-1, 61010-2-010 Connections Vacuum Inlet KF25 / NW25, quarter-turn valve Purge Inlet 5/16" Barbed, 10-turn valve Atmospheric Release Quick-release dial Contains Ships With KF25 x 1/4" JIC Flare with 1/4" vacuum hose User Manual Included Vacuum Pump Sold Separately. Warranty 3 Years Capacity and Throughput Planning Oven capacity requirements vary widely by the producer. We wanted to create a method to assist in determining the best oven match for your operation, based on a few of the parameters of your extraction and of your desired purge. We based this formula on an expected extraction yield of 25%, with an extract-density of 1 g/in2. Using the following variables, this formula is designed to provide an estimate of your required shelving capacity: Size = Extraction Batch Size (lbs) Number = Runs per 24h Period Purge = Your desired purging duration (hours) Area Required (ft2) = [(Size) * (Number) * (Purge+1)] / 122 Area Required (in2) = (Size) * (Number) * (Purge+1) * 1.18 Note: This item is a freight ship item and will ship Via UPS Ground Freight. Expedited freight can only be calculated by calling customer service 331-281-0154. All orders with expedited freight through the website will not be honored and will need to be re-quoted. A valid Phone Number IS REQUIRED to ship, Otherwise UPS freight Cannot Contact you for a delivery setup window. Freight Time is 2-5 Days. West Coast 5 Days, Midwest 2 days, East Coast 3-4 days.
$19,732.60
REFURBISHED BVV 2 Cylinder Recovery Pump
REFURBISHED BVV 2 Cylinder Recovery Pump ***NOTE: Refurbished products are 100% re-tested at our warehouse to be fully functional. The customer acknowledges that by buying a refurbished product the item may have imperfections or slight damage to the product such as: Major/Minor Scratches Major/Minor Dents Smells or Odors (Cleaned as much as possible at warehouse) 90 Day Warrantee From customer's purchase date BVV is proud to introduce our new and powerful line-up of Butane & Propane Recovery Pumps. Blending compact design with improved Gen III Pistons from RKMAC, this collection of pumps can help you recover 1lb. of butane every 1:40 Seconds! This pump Assembled in the USA and all the critical parts are domestically made. Finding parts wont be an issue with this pump. The piston seals are rated to 450F and the average operating temperature of the pump is 175F leading to a long service life. Built to meet ANSI/ISA 12.12.01 for Use in Hazardous locations Class I & II, Division 2 and Class III, Divisions 1 & 2 environments. The computer controlled brushless DC motor operates at 3000 RMP nearly twice as fast as any other pump in its class. BVV Butane/Propane Recovery Pumps are: Process up to 10,000 lbs. of vapor recovery before rebuild Equipped with oil-less reciprocating compressors for a clean product Designed and Assembled in the U.S.A. with domestic and global parts Affordable and highly cost efficient Available in 2-Cylinder, 4-Cylinder, CMEP Retrofit Comes with a 1-year Manufacturer’s Warranty covering Hemp usage Rated universal voltage 100-240V AC 50/60 Hz 1Ph Built with high efficiency Brushless DC Motor used for variable speed control Equipped with Viton O-Ring Seals for Butane/Propane gas and oil compatibility Piston Seal rebuild kits are USA made and available Part# BVV-3. Certified by ITS/ETL to ANSI/ISA 12.12.01 Noise level: 90.3 dB at 1m. Technical Data Sheet *Butane recovery results were achieved on a collection base pressure greater than 30psi and using a recovery cylinder with a pressure <10psi. A dry ice coil was used in between the output port of the pump and the recovery cylinder to condense vapor.
$1,865.63$1,363.34
CPS TRS21 Top Dead Center Piston Depth Calibration Plate
CPS TRS21 Top Dead Center Calibration Plate & Bolts Use with the Top Dead Center Clearance (TDCC) instructions Use this plate and a depth gauge to measure the Top Dead Center Clearance of the piston/cylinder/head assembly. Shims that come with the piston cylinders are stacked to create an area of displacement between the top of the cylinder and the compressor head. BVV's Recommended depth is between 0.008" and 0.012" for the CPS TRS21 for optimum performance. Top Dead Center Clearance Instructions *Depth Gauge Not included, its only used for reference in the photo. Any type of simple digital depth gauge will work to check the piston displacement.
$43.05
BVV 5.75" Glass Chamber Lid
BVV 5.75" Glass Chamber Lid This tempered soda lime glass lid is available with or without holes. Both feature 5.75" outer diameter and a thickness off 12mm or .472".
$35.88 - $50.23
Table Top Cart Filler XL 6 Liter
Table Top Cart Filler XL 6 Liter Fill 6000 1ml Carts per Load This 6 Liter capacity Giant is made to fill. Fully jacketed 304SS with a design that allows the OIL inside to fully drain creating little to no loss. The system is made of all parts that can be sterilized. The body, valves and all connections are 304 Stainless Steel and the hosing is PTFE. The body of the vessel is fully jacked and is recommended to be run with stand alone heater to pre-heat the oil. The hose is heated and insulated. The hose temperature is controlled by an Digital PID. The hose and PID controller are precision made in the USA. The hose uses Platinum Thermocouples for durability and accuracy, which means you wont run into down time or temperature errors. To use the system you will need Nitrogen to back pressure the oil in the tank. The pressure is regulated by a low pressure regulator. To dispense the end of the hose has a toggle valve that connects to a Lure Lock connection. System Specs. Nitrogen Input MAX Pressure: 150PSI Regulator working pressure: 0.5-30PSI (*recommended pressure 10PSI) Hose Temperature Rating: 50°F - 450°F Digital* Controller Temperature Range: 50°F -450° Includes Right Angle Attachment for added user flexibility. Non-Metered Dispensing with toggle valve control. Pressure gauge for pressure monitoring: 0-150PSI Cleaning: NOTE: Please Clean Prior to first use the system does not come sterilized. A simple IPA wash down will be sufficient. At any point the system can be cleaned using IPA or D-limonene. *The controller has been updated to a Digital PID controller to replace the photographed analog style rotary dial.
$3,444.24
Welch BTpro170
Welch BTpro170 ***Note: This item has a possible lead time of 2-3 weeks depending on stock availability.*** Welch’s BTpro vacuum pump series has a flow and vacuum level to provide fast performance for your size of rotary evaporator, glass reactor, purge oven, or winterization filtration apparatus. These chemical duty PTFE diaphragm pumps are oil-free. The pumping action and deep vacuum comes from the movement of PTFE diaphragms within PTFE heads. All wetted services in the flow path are made of fluoroplastic making the BTpro pump highly chemically resistant. As a result, the BTpro vacuum pump series is near-zero maintenance. A cold trap placed in-line with BTpro pump is needed if terpenes are part of the flow path. Model BTpro170 2163 Free Air Displacement@60Hz,lpm(CFM) 170 (6.0) 170 (6.0) Ultimate Vacuum Pressure, Torr 6 6 Maximum Vacuum, in. Hg 29.7 29.7 Horsepower, HP (watts) 0.6(440) 0.6(440) Built-in adjustable vacuum - - Gas Ballast Yes Yes Head Material PTFE Coated Al Diaphragm PTFE PTFE Inlet/outlet Connection NW16 flange NW16 flange Agency (National Recognized Lab) cUL cUL Weight, lbs (kg) 72.3 (32.8) 72.3 (32.8) Overall DimensionsLxWxH in.(cm) 21x11x12(53x28x31) 21x11x12(53x28x31) Shipping Weight, lbs(kg) 88.2 (40.1) 88.2 (40.1) Shipping Carton Dimensions LxWxH in.(cm) 23.6x15.8x16.1 60x40x41 23.6x15.8x16.1 60x40x41
$6,241.24
Welch ProBoost Air-Cooled Diffusion Pump
Welch ProBoost Air-Cooled Diffusion Pump Product Details Use Welch ProBoost in conjunction with a backing pump like the CRVpro to get deeper vacuum and higher flow. High Vacuum to 10⁻⁵ torr Use with high vacuum and Schlenk lines Employs air cooled diffusion pump Easy Attachment to backing pump Welch ProBoost is an air cooled gas jet pump (commonly called a diffusion pump). The gas jet is formed by directing boiling silicone vapors through a hollow cone. There are no internal moving parts. The pumping action commences when the vacuum pressure in the still (i.e. wiped film) goes below 0.2 torr (200 millitorr). On an empty, leak free still, ProBoost backed by a rotary vane pump lowers the vacuum pressure to 0.00002 torr (20x lower in pressure than a 2-stage rotary vane vacuum pump can do alone). ProBoost backed by a rotary vane vacuum pump will lower vacuum pressure to below 0.0001 torr in high vacuum and Schlenk lines. This high vacuum is invaluable to improve the results from reactions using air-sensitive compounds such as organometallics, metal amides, and hydrides. ProBoost has a built-in control board for fan and heater. When you turn on ProBoost, the fan and heater both turn on. When you turn off ProBoost, the heater turns off immediately and the fan runs for another 20 minutes to cool the pump. Specifications Maximum Pumping Speed, Air 80 l/sec Ultimate Vacuum Pressure 0.00002 torr Minimum Back Pump FAD at 60 Hz 2.8 CFM Maximum Discharge Pressure 0.2 torr Ambient Environmental Temp 10–30°C Heat-up time 7 minutes Inlet Connection NW50 Discharge Connection NW25 Silicone Oil Capacity Approximately 30 ml Cool Down Time 20 minutes Pump Dimensions, L x W x H 5.5 x 5.4 x 7.5 in Weight 5.6 lbs (2.5 kg) Download Manual
$4,447.37
Half Ton - High Purity USA ISO-BUTANE - 99.5% Guaranteed
Half Ton - High Purity USA ISO-BUTANE - 99.5% Guaranteed DISCLAIMER(S): This unit is intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. Use only in WELL VENTILATED AREAS! Notice: This item will ship via Freight ONLY. This tank requires a CGA 510 fitting - Sold Separately BVV™ always recommends distillation of every solvent before use. *Actual liquid weight is 490LB California now prohibits the retail sale of any Non-Odorized butane in quantities larger than 150ml. If you are not a retail purchaser you can call in to place an order. Permitted Sales Include the Following: Medical Collectives or Cooperatives operating under CA Health & Safety Code Section 11362.775 Persons licensed to perform volatile solvent extraction activity under CA Bus & Prof Code Division 10 Manufacturers, wholesalers, resellers, or retailers solely for the purpose of resale At BVV™, quality is everything, and our ISO-Butane is certainly no exception. This ISO-Butane is sourced here in the U.S, so you know it’s going to be of high purity: we guarantee 99.5% purity. With such high quality, you’ll see the results. By cutting down on mystery oils and other contaminants, our instrument-grade solvent will make for a higher quality extract. This solvent is clean, odorless, and colorless, meaning there are zero hydrogen sulfide-based Ethyl Mercaptan odorants. It’ll arrive in a DOT refillable LP tank, equipped with liquid withdrawal valve (Diptube). Made to keep you going for a long time. Typical Analysis: ISO-Butane >99.8% Methane <1 ppm Ethane <1ppm N-Butane <2000 ppm Propane <250ppm Isopentane <2 ppm Water <3 ppm Oxygen <5 ppm Nitrogen <10 ppm Sulfur Non-Detected **Notes: Actual ISO-butane liquid weight is 490LB BVV™ always advises distillation of every solvent before using it. DISCLAIMER: Our items are intended for LEGAL purposes only, to be used in accordance with local laws and ordinances. For safe operation, only use the unit in well-ventilated areas. ***Shipping Notes: This item will ONLY ship via UPS Ground, in accordance with FAA regulations. Any orders including solvent will NOT be shipped Expedited. If an order includes solvent as well as additional items, it will all be shipped via UPS Ground/Freight even if you’ve selected Expedited. If you want the non-solvent item to ship Expedited, place 2 separate orders; we won’t split up orders and ship them separately otherwise. We do not ship solvents to Hawaii, Puerto Rico, or any other U.S. Territory outside of the contiguous 48 States. Shipping solvent to Alaska will ONLY be via freight and will be required to travel through Canada. Our shipping policies are in place to ensure safe transport of solvents and prevent any problems with shipping times for Best Value Vacs customers
$4,233.54
20L Neocision Dual Head Short Path Distillation Kit
20L Neocision Dual Head Short Path Distillation Kit This unit carries a 2 day lead time. (Note: This kit does NOT include the stainless steel table.) The 20L Neocision Distillation Kit Setup features our Dual P10V6 Distillation Heads and USA made glass. Every component in this distillation kit is made for precision, throughput, and repeatable results. You will also receive Dual Dewar Style Ribbed Glass Cold Traps to keep all volatiles and solvents out of your vacuum system. This kit gives you the essentials of a short path distillation system and allows you to add a pump and temperature control system of your choosing. The 20L Neo Kit Includes: 20L Neocision Kit with glassware, labware, and Dual P10V6 Distillation Heads. KF-25 Bellow Y Manifold Dual Ribbed Dewar Style Glass Cold Trap Non-Mercury Glass Thermometers 20L Digital Heating and Stirring Mantle Distillation Quick Start Guide This guide gives basic quick start instructions for distillation systems. It is intended to provide a starting point for learning the process. Parameters should be adjusted to suit specific needs, Before beginning distillation, ensure the following steps have been taken: Vacuum Pump is in good working order. Pump should be run against dry load to allow internals to warm up. Oil should be clear. Cloudy or dark oil should be changed. All glass components are in good working order and ready to be assembled A winterization and degassing procedure has been done to prepare oil for distillation The unit's max internal temperature cannot exceed 380C. The recommended max set temperature should not exceed 250C Once all three of these steps have been completed, you are ready to begin distilling. Begin by placing stir bar in the boiling flask and then load your material. This should be done using a funnel. A small amount of alcohol in the oil will give it a thinner consistency making it easier to transfer. Assemble all glassware and ensure each joint is properly greased. Do not use too much, as the vacuum pressure might pull some grease into the system. To ensure a full seal, spread grease in a circular motion by rotating glassware Attach circulator to condenser and set temperature to 50C. Allow circulator to reach temperature before beginning distillation. Connect vacuum pump to manifold. The manifold will allow you to isolate each individual component as well as let atmosphere into and out of the system. Connect receiving cow to cold trap. Connect cold trap to manifold. Connect vacuum gauge to manifold. At this point, ensure all connections are correct. Also ensure receiving cow is positioned to collect the first fraction in the far-left receiving flask. Circulator should be at its set temperature. Turn on vacuum pump to begin process. Turn on heat and set to 60C. Vacuum pump will begin to pull down and temperature will begin to rise. Watch the gauge to monitor vacuum pressure and stability. Start stir slower and increase speed with temperature. Once you are close to 60C, increase the temperature 20 degrees. Continue to raise the heat incrementally in 20-degree steps, increasing the set temperature as you near your set point. Increase temperatures incrementally until you reach 220C. You will see your first fraction somewhere between 180C and 190C or slightly before. This is the “heads” fraction. You will move to your second fraction when you see an increased reaction in the head, a slight color change toward golden, as well as a thickening of distillate. When this fraction hits, allow the distillate to “self-clean” the head for a minute or two then, rotate the cow to the middle receiving flask. Collect your “main body” fraction. You will see temps between 190-220C during this fraction. Continue to increase stirring speed as necessary. Reaction in the head may vary but it should never stop. As fluid level in the boiling flask decreases, increase stir speed. The final “tails” fraction is a mixture of the first and second fractions and should be saved for re-distillation later. Ideally, you want to turn the cow to the final flask before the tails fraction hits. The “tails” fraction has an obvious color change and will be darker than the “main body” fraction. You will see temps between 200-250C during this fraction. As fluid level in the boiling flask decreases even more, set stirring RPM higher (1000+ RPM). You may need to compensate with a bit more heat to finish of the final fraction as well. Once process is complete, stop heat, stop stir, and stop vacuum. Let atmosphere into the system. Be sure to properly store your distillate as exposure to air and light can cause oxidation. *Note: This entire setup will ship via motor freight.*** *Notice to Customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. BVV™ is not responsible for the failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail, which can cause bodily harm or damage to the surrounding area.
$9,758.67 - $10,045.69
True Terpenes Pie Hoe - Infused
True Terpenes Pie Hoe All sales are final. Orders can be refunded prior to fulfillment and shipping but once the order has been fulfilled and/or shipped, no refunds will be issued. Due to the hazardous nature of our product, we are unable to accept returns. (Please Note: This product has 1 week lead time) Pie Hoe Infused Strain Profile takes the sensual and euphoric combination of Grape Pie and Tahoe OG strains and increases the love with silky smooth berry. Full Flavor. Full Effect. FRAGRANCE: Berry EFFECT: Sensual and euphoric CERTIFICATES: COA | SDS | FOOD GRADE Storage Requirements Keep in original container, lid securely tightened and away from heat, open flames, sunlight, combustible materials and hot surfaces. Store below 15℃ (60℉). Improper storage can cause terpenes to degrade. DilutionTerpenes must be diluted prior to use for flavor and effect (1-5% by total volume). Terpenes are oil soluble and mix well with plant extracts, coconut oil, and more. Handle With CareCan cause skin irritation, do not ingest PRIOR to dilution. TRUE GRADE™ It is our promise to you. Our isolated terpenes are triple-distilled making them the cleanest terpenes in the world. Fresh out of the bottle, undiluted, every single one of our products bests the most rigorous consumer safety standards. GMP | ISO-9001:2015 | FSSC 22000 Blended in cGMP facilities adhering to the requirements for a Quality Management System (QMS) specified by ISO 9001:2015 and FSSC 22000 standards. Analyzed Tested and passed True Grade™ safety specifications for residual solvents, pesticides and heavy metals. Stability Tested Rigorously tested with mid-grade distillate against separation, cloudiness and unacceptable levels of color change. We Qualify True Terpenes implements supply-chain control for all raw materials and is proud to provide True Terpenes’ qualification documents such as certificates, licenses and registrations to be qualified as your supplier. Undiluted We do not add PG, VG, PEG, MCT or Vitamin E Acetate to any of our products. Food Grade Manufactured in cGMP facilities using food grade ingredients. UV Protected This product is packaged in a cobalt blue, UV deterrent and food grade bottle with tamper evident seal. Made in the USA Formulated, blended, manufactured and fulfilled in the United States. Refined Isolates This product contains ultra-pure, molecularly-refined terpene isolates. Only the best.
$174.36 - $3,228.97
HUBER Unistat T305 with Pilot ONE
HUBER Unistat T305 with Pilot ONE (Please Note: There is a 2 - 3 weeks lead time) The Unistat range inspires with unique thermodynamic properties and a range of functions to meet the highest demands. Unistat technology guarantees precise, reproducible temperature control results, the shortest possible heating and cooling times and large temperature ranges without the need for fluid change. All Unistats are fitted with the innovative Because Unistats are hydraulically sealed, the service life of the temperature control fluid is dramatically increased by preventing oil loss through vapours and oxidation, further saving resources. Unistats are fitted with extensive safety equipment and are therefore suitable for unsupervised continuous operation. Relevant operating conditions are constantly monitored and the system is switched off if necessary or with the process safety feature the emergency cooling circuit is activated. Data sheet 3 Year Warranty Extension General Information & Temperature Controller Temperature range 65...300 °C Temperature stability ±0,02 °C Temperature control TAC, self-optimizing (True Adaptive Control) Controller Pilot ONE (E-grade "Basic") Safety class III / FL Protection class IP20 Dimensions (W x D x H) 425 x 250 x 631 mm | 16.73 x 9.84 x 24.84 inches Weight 37 kg | 81.59 pounds Heating / Cooling Capacity Heating capacity 4,8 kW Circulation Pump Pressure pump max. 45 lpm ; 0.9 bar | 11.89 gpm ; 13.05 psi Pump connection M24x1,5 AG male Permissible viscosity 50 mm²/s Connections Pt100 connection Pt100 Analogue input via optional Com.G@te Analogue output via optional Com.G@te Digital interface RS232, Ethernet, USB Device, USB Host Operating Data Old sku 1003.0022.01 Permissible ambient temp. 5 to 40 °C Filling volume min. 1.45 Liters | 0.38 gal Volume of expansion 2.8 Liters | 0.74 gal Power supply 208V 3~ 60Hz Current max. 15 A Fusing 15,5 A
$32,720.24 - $33,437.79
Polyscience 20 Liter General Purpose Water Bath
Polyscience 20 Liter General Purpose Water Bath Key Features: Displays actual and set point temperature simultaneously Three push-button pre-sets for frequently used temperatures Integrated timer Hinged gable cover Calibration capability Reservoir sizes from 2 to 28 liters Reservoir made of 304 Stainless Steel Reservoir drain (10 liter and larger baths) Primary and automatic safety thermostats Also compatible with waterless bath beads Specifications Working Temperature Range °F Ambient +10° to 212° Reservoir Capacity (liters) 20 Reservoir/Tank Material Stainless Steel Reservoir Cover Hinged Gable Working Access (L x W x D) (inches) 9.5 x 17 x 6 Temperature Stability °F ±0.2° Display 3.25" Flammability Class (DIN 12876-1) I (NFL) Over-Temperature Protection / Failsafe Heater Control Yes Maximum Ambient Temperature °F 104° Overall Dimensions (L x W x H) (inches) 17.5 x 22.5 x 15.5 Shipping Weight (pounds) 25.0 60Hz Only Part Number WBE20A11B Included Hardware Sample Tray Heater Wattage 1400 Electrical Requirements (VAC/Hz/Ph/A) 240/50/1/6 Regulatory Approvals ETL Certifications: Regulatory Approvals: ETL Approval CE Approval Operator's Manual
$1,684.81
J-KEM® Temperature Controller Model 260/Timer Complete
J-KEM® Temperature Controller Model 260/Timer Complete Designed for processes requiring an extra measure of safety. The Model 260/Timer disconnects outlet power if the process temperature exceeds the set point by a user-specified amount, or following recovery from a power failure. Power remains off until the controller is manually reset. Over temperature is signaled by both an indicator lamp and an audible alarm. Contains a 100-hour digital timer to turn heating OFF (or ON) when the time expires. The Model 260 has two power outlets (1800 watts) for large equipment or heating mantles up to 22L. Contains J-KEM’s patented power control computer which provides 0.1° regulation of anything. SPECIFICATIONS: Power: 15 amps @ 120 VAC, 1800 Watts Weight: 6 Lbs Dimensions: 9.25 × 7.75 × 3.5 in .
$1,858.45 - $2,102.42
Williams Double Open End Chrome Wrench Set
Williams Double Open End Chrome Wrench Set Williams Double Open End Chrome Wrench Set is made in the USA and the two openings in each wrench with 45° chamfer on wrench ends allow easy placement of wrench on the fastener. Continuous arc design minimizes spreading and is stronger than V design. Satin provides good grip and cleans easily. This Kit Includes the following wrench sizes: 9/16" x 5/8" Double Open End Chrome 5/8" x 11/16" Double Open End Chrome 5/8 x 3/4" Double Open End Chrome
$57.40
1.5 Gallon Tall Stainless Steel COLD TRAP - POT ONLY
1.5 Gallon Tall Stainless Steel COLD TRAP - POT ONLY ***Note: Hardware Only Includes the Flares with Bulk Heads preinstalled. (Does not Include Lids or Gaskets) This is a replacement part for the following Vacuum Chambers: 1.5 Gallon (2QT Tank) Dry Ice, Liquid Nitrogen Cold Trap Dimensions: 8-5/8"" Tall x 7-1/8"" Diameter Material: 304 - 2B Stainless Steel
$83.24 - $100.46
Polyscience 7 Liter Standard Digital Refrigerated Circulator (-20°C/170°C)
Polyscience 7 Liter Standard Digital Refrigerated Circulator (-20°C/170°C) ***Note: This item has a possible 2-3 week lead time depending on stock availability.*** Specification Description -20, 7 L Ref. Circulator Controller Type Standard Digital Display 3.75" Touch-Pad LCD Connectivity RS232 Swivel 180 Rotating Controller Yes Working Temperature Range °C -20° to 170° Temperature Stability °C ±0.04° Fluid Optimization/Specific Heat Tuning Automatic Temperature Calibration Capability 1-point Working Access (L x W x D) (cm) 15.7 x 14.2 x 12.7 cm Pump Type Pressure Flammability Class (DIN 12876-1) I (NFL) Working Temperature Range °F -4° to 338° Working Temperature Range °C -20° to 170° Nominal Cooling Capacity @ +20C (W) 200 Reservoir Capacity (gallons) 1.85 Reservoir Capacity (liters) 7 Reservoir/Tank Material Stainless Steel Reservoir Cover Included DuraTop Yes LidDock Yes Cleanable Air Filter Yes Reservoir Liquid Level Indicator Yes Working Access (L x W x D) (inches) 6.18 x 5.59 x 5 in Working Access (L x W x D) (cm) 15.7 x 14.2 x 12.7 cm Temperature Stability °F ±0.08° Temperature Stability °C ±0.04° Display 3.75" Touch-Pad LCD Display Resolution (Set) 0.1 Display Resolution (Read) 0.1 Pump Type Pressure Pump Speed Two Process Connections 1/4" (F) NPT Flammability Class (DIN 12876-1) I (NFL) Over-Temperature Protection / Failsafe Heater Control Yes Low Liquid Level Protection Yes Reservoir Drain Yes Maximum Ambient Temperature °F 95° Maximum Ambient Temperature °C 35° Overall Dimensions (L x W x H) (inches) 21.3 x 8.7 x 24.3 in Overall Dimensions (L x W x H) (cm) 54.1 x 22.1 x 61.7 cm Refrigerant R134a Environmental Compliance RoHS, WEEE Shipping Weight (pounds) 90.0 Shipping Weight (kilograms) 40.8 Catalog Page Number 42-43 60 Hz Only Part Number SD07R-20-A11B Maximum Pressure (psi) 3.5 Maximum Pressure (bar) 0.24 Maximum Pressure Flow Rate (gpm) 2.90 Maximum Pressure Flow Rate (l/min) 11.0 Cooling Capacity @ -20°C (W) 30 Cooling Capacity @ 0°C (W) 120 Cooling Capacity @ +20°C (W) 200 Cooling Capacity @ +100°C (W) 200 Included Hardware Nylon hose adapters for 3/8", 1/4", and 3/16" Heater Wattage 1100 Electrical Requirements (VAC/Hz/Ph/A) 120/60/1/12 Regulatory Approvals ETL Key Features: Large, universal icon and English display Swivel 180™ Rotating Controller On-board connectivity: RS-232 serial output On-screen prompts Automatic performance optimization Single-point calibration capability Operator's Manual
$5,682.99
10L & 20L Bump Trap
10L & 20L Bump Trap *Notice to customers: All units are inspected for broken glassware or parts before leaving BVV™. If the unit arrives damaged (this does not include minor imperfections or scuffs in glassware), the customer MUST contact BVV™ within 72 hours from carrier delivery to file a claim. If the customer DOES NOT contact BVV™ within 72 hours from carrier delivery, then BVV™ cannot issue any replacement(s) or compensation for the item; a new purchase will need to be made for a replacement. **Glassware Safety Disclaimer: BVV™ is not responsible for failure of glassware which must be inspected before and after every use because it may eventually develop imperfections or damage through normal usage, mishandling, and stress caused by temperature variations. If an imperfection or damage is noted while inspecting the glassware DO NOT use the glassware because it can fail causing bodily harm or damage to the surrounding area.**
$344.42
Welch ChemStar 1400N 0.9 cfm 0.1 Micron Belt Drive 2-Stage Pump
Welch ChemStar 1400N 0.9 cfm 0.1 Micron Belt Drive 2-Stage Pump ***Note: This item has a possible 1-2 week lead time depending on stock availability.*** Product Details Low rotation speed for longer service life Vital parts corrosion resistant Large oil reservoir dilutes contaminants ChemStar belt-driven Vacuum Pump is designed to tolerate harsh chemical contamination. Vital pump parts are corrosion resistant. The large oil reservoir with PTFE surfaces dilutes contamination and the low pump rotational speed lessens friction to reduce operating temperature and chemical effects. PTFE surfaces, fluorcarbon gaskets and seals, Nitrogen purge to cool and degas oil. ChemStar system comes with Gold Oil, a synthetic lubricant designed to minimize effects of chemical contaminants. Specifications Model Number 1400N Application Vacuum Manifolds, (Schlenk Lines), High boiling point evaporations (to 195 deg. C), General laboratory. HCl, O3, H2SO4*HBr, HOAC, SOx*Br2, F3CCO2H, H2S*Cl2, CH2O, HNO3*SF6, CF4 Fragments and other gases; Type Belt-Drive Vacuum Pump, chemical resistant Free Air Displacement cfm (l/min.) @60Hz 0.9(25) Ultimate Pressure 1 x10-4(0.00013) Pump RPM 580 Oil Capacity 0.62(0.59) Motor Horsepower (watts) 1/3(250) Adjustable Vac. / Gas Ballast Yes Tubing Needed 7/16(11) ISO Exhaust / Intake Flange NW 16 Overall Dimensions LxWxH in. (cm) 17.8x9x12.6 (45.2x22.9x32) Ship Weight 71(32.3) Shipping Carton Dimensions LxWxH in. (cm) 20.5x13.8x14.5 (52.1x35.1x36.8)
$3,920.69 - $4,979.79
Reducer/Adapter
SSP Reducer/Adapter SSP Instrumentation Duolok® tube fittings are designed, manufactured and quality controlled to be totally “interchangeable” with the Swagelok® brand of tube fittings. Component by component examination plainly shows the two brands as completely “componentintermixable.” The precision manufacturing of both products to stringent tolerances under rigid quality control procedures ensures the safety, performance, and reliability of service whenever Duolok® and Swagelok® component parts are mixed and used in accordance with published installation and service recommendations. Specifications Connection Type 1 Duolok Tube Fitting Connection Size 1 Specified by User Connection Type 2 Tube Stub Connection Size 2 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Duolok Pressure Rating = Tubing Rating SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA! Dimensions A 1.54 in C 0.70 in D 0.60 in E 0.11 in G 9/16 in H 1/2 in T 1/4 in B 1.25 in Tx 1/4 in
$10.76 - $12.92
Female Run Tee
SSP Instrumentation Duolok® tube fittings are designed, manufactured and quality controlled to be totally “interchangeable” with the Swagelok® brand of tube fittings. Component by component examination plainly shows the two brands as completely “componentintermixable.” The precision manufacturing of both products to stringent tolerances under rigid quality control procedures ensures the safety, performance and reliability of service whenever Duolok® and Swagelok® component parts are mixed and used in accordance with published installation and service recommendations. Specifications Connection Type 1 Duolok Tube Fitting Connection Size 1 Specified by User Connection Type 2 Duolok Tube Fitting Connection Size 2 Specified by User Connection Type 3 Female NPT Connection Size 3 Specified by User Material 316 Stainless Steel ASTM A-276 and A-479 bar stock, A-182 forgings. Duolok Pressure Rating = Tubing Rating NPT Pressure Rating >10,000PSI ASME B31.3 SSP proudly makes Duolok®, TruFit®, FloLok® and hundreds of other products 100% in the USA!
$34.44 - $41.62
160L Jacketed Stainless Steel Centrifuge with Explosion Proof Motor and Siemens Controller - 55LB Max Capacity
160L Ethanol Wash/Dry Centrifuge with Explosion Proof Motor and Controller Notice to Customer: This unit has 4 lift points (one in each corner) and requires a forklift to lift it. It will also ship via freight only. Industrial Centrifuges are used to separating liquids from solids and this style of centrifuge excels at alcohol extraction by forcefully separating the alcohol from the biomass. Key Features: Siemens Touch Screen Controller Explosion Proof Controller Housing and Motor Agitation and Spin Dry Modes Max 1200 RPM with Gradual Speed Stepping 643 Separation Factor Multiple Connection Ports/Sizes High Polish Stainless Steel Components Shock absorbing legs Vacuum Jacket with Two 1" Tri-Clamp Fittings Pre-wired and Tested for Easy Installation Specifications Capacity 160L Drum Dimensions 31.5" (800mm) Diameter x 12.6" (320mm) Depth Speed 0-1200r/min Weight 3307lbs (1500KG) Exterior Dimensions 51.2" x 72.8" x 43.3" (1300 x 1850 x 1100mm) Material 304 Stainless Steel Motor Power 7.5KW Explosion Proof - 220v 60Hz 3 Phase
$46,640.70
ULVAC DA-40S 1.6 Cfm Oil-Free Diaphragm Pump
ULVAC DA-40S 1.6 Cfm Oil-Free Diaphragm Pump (Please note: This item has a minimum 6 week Lead Time) This Diaphragm Dry type pump creates vacuum by reciprocate movement of rubber diaphragms. The structure of this pump makes Oil-free environment and maintenance easy. Different pumping speed and two/single stages are optional depending on your required pressure and pumping volume. Applications: Vacuum chucks, wafer and tip handling devices. Vacuum tweezers, medical appliances. Printing equipment. Automatic packing machines. Optical appliances. Specifications Unit 50Hz - 60Hz Actual Pumping Speed L/min 40 - 46 Ultimate pressure Pa 19.9 x 10^3 Motor Single phase, 100V, 60W, 4P, Capacitor run Full load current A 1.6 Weight kg 7.2 Inlet, outlet pipe diameter mm O.D. dia.9 × I.D. dia.5 (Rc 1/4) Ambient temperature °C 7 – 40 Overall dimensions mm 128(W) × 242(L) × 178(H)
$1,707.77
Grodan Improved GR40 Uniblock, 8" x 8" x 4", case of 36
Grodan Improved GR40 Uniblock, 8" x 8" x 4", case of 36 Product Details Grodan partnered with the Wageningen University and Research facility in The Netherlands and top growers throughout North America to identify the optimal stone wool substrate and irrigation strategies for specialty crops. The result of months of scientific research and trials is Grodan Gro-Blocks Improved with Grodan’s Advanced Wetting Agent. These leading-edge blocks have the optimal fiber structure and physical properties for crop uniformity, more even Water Content (WC) and Electrical Conductivity (EC) distribution throughout the entire block, and the greatest steering capabilities available. Water distribution is more uniform throughout the entire block which is the basis for a well-defined root system with higher capacities for water and nutrient uptake to produce robust and vigorous crops. New and improved wetting agent and hydrophilic technology greatly enhances the water characteristics of Grodan Gro-Blocks Improved giving even better water distribution over the height of the block. This results in greater plant development and steerability and more efficient use of water and nutrients.Optimized wool structure allows for faster rooting-in and nutrient solution replenishment, all while the Gro-Block Improved maintains its structure, firmness, and rigidity throughout the growing process. Note: This item is for commercial use and is packaged as bulk, without retail wrapping or labeling.
$305.32$234.39
Phantom PHENO 440 LED, 440W, 100-277V, MP Spectrum
Phantom PHENO 440 LED, 440W, 100-277V, MP Spectrum Product Details The Phantom PHENO 440 horticultural lighting system combines high photon flux with superior efficiency. The low-profile design and wide voltage range is ideal for a wide range of applications. Two adjustable light bars allow user to adjust light spread. Integrated output knob and PX port provides control over the amount of photons to the plant canopy. This efficient and versatile system is compatible with PX series controllers (sold separately) to manage photoperiod and output. Suitable for both flowering and vegetative stages, the Multi Phase (MP) spectrum provides ideal red to blue ratio for vigorous growth and to maximize flower development. Features: 1100 μmol/s PPF @277V 2.5 μmol/joule PPE @277V 440W, 100-277V Driver High-efficiency Multi Phase spectrum Integrated flux control knob PX2 Lighting Controller Compatible Compact sized: 31.49"x 16.8" x 4.1" Net Weight: 19.4lbs/ 8.8kg Includes 10' 120V power cord DLC listed (H-LORIQO2) and qualifies for utility rebates, which play a significant role in optimizing the cost effectiveness of a lighting project The Phantom PHENO offers the functionality of an on board dimming knob, allowing the grower to adjust the photon output intensity to accommodate the various stages of plant growth for optimal photosynthesis activation. With the knob adjusted to 100%, the PHENO uses 440W and puts out 1100 μmol/s photon flux (PPF). With the knob adjusted to 40%, the PHENO uses 176w and puts out 40% of the photon flux. The Multi-Phase spectrum does not change when using the dimmer knob and still provides ideal red to blue ratio for vigorous growth and to maximize flower development. KNOB POSITION CONDITION/NOTES PHOTON FLUX (µmol/s) AVERAGE POWER (WATTS) EXT SWITCH THE KNOB TO THIS FOR USE WITH 0-10V CONTROLLER VARIABLE VARIABLE OFF NO LIGHT EMMITTED 0 µmol/s 0W 100% 100% OF TOTAL LIGHT EMMITTED 1100µmol/s 440W 80% 80% OF TOTAL LIGHT EMMITTED 880 µmol/s 352W 60% 60% OF TOTAL LIGHT EMMITTED 660 µmol/s 264W 40% 40% OF TOTAL LIGHT EMMITTED 440 µmol/s 176W
$861.04$703.18
Autopilot CO2 Replacement Sensor w/15' Cable (for APC8200)
Autopilot CO2 Replacement Sensor w/15' Cable (for APC8200) Product Details This is a replacement CO2 sensor for the Autopilot APC8200 Remote CO2 sensor probe w/photocell & 15' data cable lets you take readings from proper grow room locations 2-Channel Low Drift NDIR Sensor precisely reads CO2 ppm levels
$223.86$180.52
iPonic iGrow 800 Greenhouse Controller
iPonic iGrow 800 Greenhouse Controller iGrow 800 Greenhouse Controller Advanced control, affordable price Fully-programmable; expansion to 32 outputs Use your cell phone to monitor and change settings Get peace of mind with alerts for temperature, humidity, CO2 and more UL Listed for safety and easy permits Get real-time energy use and track run-time on greenhouse heating and cooling equipment with this easy-to-use controller system. The iGrow 800 series offers eight different ouputs for fans, heaters, vents, irrigation, shade curtains (blackout curtains), and more – with Cloud access from any Internet-connected computer or smartphone.Track your energy usage across 8 intelligently controlled outputs (expandable to 32) and adjust to increase your profit. Tools such as LinkConn Software expand the capabilities of this versatile line of controllers to further save energy and increase your profit. No more programming and reprogramming every crop cycle or season change – with the iGrow 800 series USB data logging feature you can easily save settings to any USB flash drive. When the time comes to switch settings, simply insert your USB flash drive into your iGrow data. These are some of the new and innovative ways Link4 has provided to reduce setup times and reduce your labor costs. Remote Cloud AccessGrowers can monitor and change every aspect of the iGrow800 from the palm of their hand, using state-of the-art controls that relay secured, encrypted grow house data to the cloud where it is accessible on any Internet-connected device. The secured, encrypted server allows you to monitor and change settings remotely. With a wealth of data at their fingertips, growers are able to grow bigger, more vibrant crops under repeatable processes. Easy TransitionThis programmable controller offers integrated control for easy transition to an advanced, yet simple-to-use system. It is ideal for small or large greenhouse retrofits or new installations. Included communication module lets you link multiple greenhouses for control. Loss Prevention The iGrow 800 protects their grow house investment with SMS text and email identifying a variety of threats, including spikes in temperature, humidity, and CO2. Emergency shut-off guards against power surge and overheating. Privacy and Security Network architecture built to meet the requirements of the most security-sensitive organizations No data collected by the Cloud is shared to a third party User location data collected is anonymous and cannot be associated with a user account Tor and Anonymity Online Compatible
$3,348.07$2,155.62
Anden 5701 Replacement Filter for Anden Dehumidifier Model A130
Anden dehumidifiers are designed for maximum growth. The 5701 Multi-Pleat 11 is produced with a highly specialized, dual layered 100% synthetic media, specifically for use in Anden dehumidifiers. The Anden 5701 is composed of an upstream electrostatically enhanced layer (the E-Layer), and a downstream mechanical layer (the M-Layer). This replacement filter is easy to install, with no assembly or reinforcements to worry about. Protect your equipment for optimal performance. INCLUDES: (6) Replacement filters for ANDEN Dehumidifier Model: A130 DIMENSIONS: 14 x 19 x 1 MERV 11 Filter for Superior Equipment Protection Upgraded protection from standard pleated filters High holding capacity Anden Dehumidifiers are designed with easy access for simple filter changes
$55.11
BioSafe PVent
PVent Biofungicide is an enhancement in microbial fungicide technology, providing growers with an easy-to-use, versatile IPM tool. This innovative development was spearheaded through a strategic partnership between two family-owned businesses: BioSafe Systems and Lallemand Plant Care. BioSafe’s Sustainable Soils Program combines decades of experience and trust in fumigation practices to drive innovation in biorational and sustainable crop protection solutions. The strategic partnership between BioSafe and Lallemand, built off collective expertise, makes PVent one of the most concentrated EPA-registered biofungicides in its category. Powered by three modes of action, PVent is biologically programmed to rapidly colonize its host environment to defend against, attack and destroy even the most resilient plant pathogens.PVent’s active ingredient is a 93% Gliocladium catenulatum Strain J1446, originally isolated from natural Finnish soils. The J1446 Strain includes some unique adaptation traits, including its enhanced ability to thrive and reproduce across broad temperature and humidity ranges. PVent’s G. catenulatum Strain J1446 was isolated and researched extensively due to its natural symbiotic relationship with the plant rhizosphere, the stem and foliar surfaces, and most importantly its versatility in an IPM program – this is due to an enzyme secreted by G. catenulatum, specifically targeting pathogenic fungi.PVent is formulated into a wettable granule (WG) that can be readily dispersed, mixed and applied through multiple practices.
$596.99$396.16
Hydrofarm - Green Premium Saucer
Listed diameter is measured from the inside of the bottom of the saucer. These sturdy and reusable green saucers come in various sizes to match most pots. Use them to collect excess water drainage and soil spillage. Features Ribbed bottom keeps plant out of water and prevents plant from sticking to saucer Checking water levels is a snap Sturdy, rugged, and reusable Protects floors and decks from water
$24.80$24.28
FoxFarm - Cha Ching
FoxFarm engineered Cha Ching® to maximize a plant's production. Every stage of the growing cycle demands optimal nutrition. Cha Ching® is a high-phosphorus fertilizer that won't leave a salty residue or build up in the soil. Even better, we've included the micronutrient pack that FoxFarm is known for. It contains all the essential elements you need to support juicy fruit on compact, stocky plants. Cha Ching® creates juicy, robust fruit with essential oils and resins pumping out of stems and leaves. That means concentrated flavor and perfect texture. After flowers are fully formed, switch to Cha Ching® and continue through harvest. Feed with every other watering (this is a late flowering formula).
$32.22
FoxFarm - Bush Doctor Kangaroots
Bush Doctor® Kangaroots® is a liquid root drench formulation for use on in-ground plantings, container gardens and hydroponic systems. Use on seedlings and mature plants to enhance the proliferation and root mass development of both primary and secondary roots.Kangaroots® also contains concentrated amounts of microbes designed for hosting not only directly on the roots, but in the soil around them. Kangaroots® supplies essential macro and micronutrients that plants thrive on for both hydroponic and soil applications. For optimal results, follow the FoxFarm feeding schedule. A liquid root drench formulation designed to enhance the proliferation or root mass development for both primary and secondary roots Contains nutrition specifically designed to be instantly available for roots to absorb at optimal levels Can be used in both hydroponic and soil applications
$45.26
SunBlaster 1020 Quad Thick Tray
These are standard 1020 trays with the exception that they are four times the thickness of traditional trays. Long lasting and reusable.
$8.08
Grodan Pro A-OK 50/40 6/15, 2"x2", case of 1,500
Grodan Stonewool (rockwool) is made from molten rock spun into cotton candy-like fibers and then compressed into cubes, blocks, or slabs. Where other rockwool brand manufacturers cut all sizes from one batch of wool, Grodan is unique by making different types of fibers. The purpose is to support the requirement of the plant in the different plant stages. Grodan has a tremendous capacity for absorbing nutrient solution while retaining plenty of oxygen for rapid plant growth. Grodan comes in graduated sizes. Seedlings started in cubes are easily transferred to blocks and then onto slabs, if desired. Seedlings or cuttings started in the Grodan cubes can also be transplanted into more traditional planters and growing mediums. Grodan A-OK plugs are designed for seed and cutting propagation prior to "blocking on" into larger growing blocks. The V-shape design of the plug discourages tangling of roots between the plugs in the A-OK plug sheet. A-OK plugs come in a sheet that fits a standard 10x20 flat. Note: This item is for commercial use and is packaged as bulk, without retail wrapping or labeling.
$633.38$492.57
Grodan Expert Slab
PLEASE NOTE: THIS ITEM IS NOW 12 PER CASE. Grodan Stonewool (rockwool) is made from molten rock spun into cotton candy-like fibers and then compressed into cubes, blocks, or slabs. Where other rockwool brand manufacturers cut all sizes from one batch of wool, Grodan is unique by making different types of fibers. The purpose is to support the requirement of the plant in the different plant stages. Grodan has a tremendous capacity for absorbing nutrient solution while retaining plenty of oxygen for rapid plant growth. Grodan comes in graduated sizes. Seedlings started in cubes are easily transferred to blocks and then onto slabs, if desired. Seedlings or cuttings started in the Grodan cubes can also be transplanted into more traditional planters and growing mediums. Grodan Slabs - The final stage of planting with growing blocks are the Grodan slabs. These slabs come in clearly marked UV resistant poly sleeves for ease of use. Recommended for larger, long term crops with extensive roots like peppers, tomatoes, or cucumbers. Typically, seedlings in blocks are placed onto slabs. Grodan Expert is the slab that drains the fastest because of its vertical fibers. By far the most popular slab for the hydroponic hobbyist market. Grodan Master is a special wet/dry slab. The top layer is thicker, which stays wetter, while the bottom layer stays drier. In effect it defies gravity, allowing more even distribution of moisture throughout the slab.
$200.21$173.10
Active Aqua Root Spa 5 gal 4 Bucket System
The Root Spa is a deep water culture system. This 5 gallon bucket system is so simple yet grows large plants efficiently. After a very short time, you will realize the advantage of the simplicity of this uniquely easy-to-use, inexpensive, and forgiving system! Pumping raw air into the nutrient solution, without the need of expensive and often troublesome air stones is not only cost effective, but your plants will also thrive! • Watertight seal to guarantee no leaks • 8" bucket basket to hold your choice of growing medium• Multi-purpose air hose delivers air from the pump to the bottom of the bucket• Air pump oxygenates your water and encourages root growth• ½" grommet fitting• ½" elbow fitting• ¼" black tubing Media sold separately: You can use your choice of hydroponic media, such as clay pebbles, #4 perlite, rockwool mini cubes, coco chips, etc. Since this is a hydroponics system, soil should be avoided. Soil may contain dust, fungi, and bacteria, all of which can contaminate a hydroponics system. NOTE: Setup of the multi-bucket Root Spa system is the same as that of the single-bucket system, with the main difference that the multi-bucket system uses a multi-output air pump, while the single-bucket Root Spa systems use a single dedicated air pump. Praise for the Root Spa: “It’s easy to tell when your plants are supercharged. You don’t need any fancy meter for that—it’s visually apparent. Every time you open the door to your garden your plants almost roar at you! The speed of their development is shocking—even over a single day—they are visibly taller, fuller, bigger, and happier. I love it when my garden is cranking like this.” Watertight seal to guarantee no leaks 10-inch bucket basket to hold your choice of growing medium Multi-purpose air hose delivers air from the pump to the bottom of the bucket Air pump oxygenates your water and encourages root growth So simple yet grows large plants efficiently
$193.15$154.52
Roots Organics Procision Perlite #4
Procision Perlite Coarse is cut with a ten mesh screen leaving all material to retain #4. Perlite ore is a naturally occurring volcanic glass containing a small percentage of water. When that ore is introduced to tremendous heat the glass liquefies and the trapped water expands creating a remarkable and versatile material. In an ongoing quest to improve the quality of our products, Aurora Innovations recognized the opportunity to begin producing another of their own materials. Success at a new venture is never easy, but they're really excited about the quality of their production.
$86.03$76.69
oxyCLONE PRO Series Cloning System
oxyCLONE 20 and oxyCLONE 80 Site System oxyCLONE is a simple, compact, recirculating cloning system. It works with a variety of cuttings, allowing you to have a perpetual garden year-round. Now powered by Active Aqua's premium, BPA-free water and air pumps! The submersible pump delivers constant turbulence to your reservoir while the attached Venturi valve naturally draws in air bubbles. For maximum aeration, the single-outlet Active Aqua air pump provides a constant flow of dissolved oxygen through a circular 4" air diffuser. No other cloner delivers dissolved oxygen like the oxyCLONE! Cloning System Features: Maximum oxygenation Won't leak or clog Evaporative cooling means less retained heat Powered with the Active Aqua AAPA3.2L single outlet air pump and Active Aqua AAPW160 submersible water pump! Maximum oxygenation Evaporative cooling means less retained heat Powered with Active Aqua premium pumps Works with a variety of cuttings For more tips and FAQs, please visit www.oxyclone.com.
$129.14$128.54
Active Aqua - Porthole Cover, Black - FITS ALL SIZES
The Active Aqua porthole cover fits all sizes of reservoir covers we offer. It helps minimize evaporation and contamination of the nutrient solution in the reservoir, and also provides quick access to the reservoir for routine maintenance such as checking pH and adding nutrients.
$17.92$16.72
Hydrofarm - Precision Curved Lightweight Titanium Pruner
These lightweight anti-fatigue pruners are based on our immensely popular classic Hydrofarm pruners, favored by legions of horticulturists. Their surgical stainless steel blades offer serious cutting capacity in a lightweight package. These snips feature razor-sharp blades, perfectly balanced construction, and an ultra-lightweight, ergonomic design FEATURES: Super-sharp tapered blade tips for ultimate cutting precision Right or left handed use Titanium-coated surgical stainless steel blades hold a sharp edge longer Extra-long blade shanks Ergonomic design reduces stress to the hand Anti-slip soft gel handles Ultra-lightweight Safety lock
$26.98
Square Basket, 9", bag of 24
Grow like a pro with Hydrofarm's net cups, mesh pots, and baskets. A wide assortment of sizes and mesh patterns make it easy to choose the best container for all your plants. Use these pots with any of your favorite growing media to ensure even drainage and promote bigger, healthier roots!
$50.34
Grow More Mendocino Flower & Bloom 6-30-30, 25 lbs
Grow More's Mendocino Producer's Choice line of fertilizers are the most advanced powders we've ever created. They are 100% water soluble formulas containing a properly balanced mixture of all essential plant nutrients with quality-enhancing elements; calcium, magnesium, DTPA/EDDHA Iron, carbohydrates, amino acids and no artificial dyes or colorings. This Mendocino line provides highly efficient, performance nutrients as a standalone base nutrient or as a vegetative and bloom stimulant. For use in soilless, hydroponic, organic soils and coco coir systems. For those special requirement low Nitrogen situations when high amounts of Phosphate and Potassium are needed to firm or size fruits or vegetables.
$165.02$130.68
Grow More Mendo Soluble 20-20-20, 25 lbs
Widely used in agricultural and horticultural application, special ingredients designed for immediate utilization by the plant provide balanced N-P-K, multiple sources of nitrogen and fully chelated micronutrients. High phosphate in the plant usable form ideal for deficiency correction or as a young plant starter. No Chlorides. 100% Soluble. Designed to maximize the final phase of a plants production. Recommended for use on vegetables. WATER SOLUBLE FERTILIZERS The first chemical revolution in agriculture started over 100 years ago, when soil fertilization was discovered; the second chemical revolution—the idea of foliar feeding as an effective and important tool in crop fertility—is going to be common only in our generation. Leaf feeding or foliar fertilization with Grow More Fertilizers can increase yields of a healthy crop beyond the capabilities of conventional, soil applied fertilizers. Used correctly Grow More Water Soluble Fertilizers can provide an attractive economic return on investment over and above that obtained from soil applied fertilizers. Foliar Spray Grade Made with Low Biuret Urea Drip-Irrigation No Sediment Multi-Nitrogen Sources Versatile - Foliar sprays or infector systems. Grow More Fertilizers are formulated to supply sufficient amounts of extra nutrients for high yields. Grow More are supplements to be used in addition to normal soil applied fertilizers and do not compensate for the lack of good cultivation and mangagement practices. If used correctly and with experience, soil applied fertilizers can be cut back as much as 20% when Grow More is used in a foliar fertilizer Program. Grow More Fertilizers are designed to meet a need for a properly balanced, highly concentrated product that can be applied by aircraft or ground rigs, as well as used in dilute or concentrated sprinkler or injector systems. Grow More Fertilizers are versatile products that meet many requirements; consider the following: 100% soluble nutritional foliage spray that can be applied to fruit and otfter crops nearing maturity. leaving little or no visible residue at harvest Safe and effective for many different species and sizes of plants grown together in greenhouses and nurseries Contain elements which provide the entire spectrum of nutrients needed for a wide variety of plants Provides a source of immediately available plant nutrients. Particularly suitable for fast growing field, vegetable, and nursery crops 100% soluble and does not need agitation in the tank Formulated to be compatible with most common pesticides and fungicides - especially suited for aircraft applications Can be used as both a spreader and acidifer Uniform in analysis every drop contains the same analysis Contains chelating and sequestering agents to assure availability without precipitation of the major and micronutrients Contains no chlorides
$152.11$109.73
FoxFarm Ocean Forest Potting Soil
The ultimate potting soil—everything your plants need, in one bag. Ocean Forest® is a powerhouse blend of premium earthworm castings, bat guano, and sea-going fish and crab meal. Aged forest products, sandy loam, and sphagnum peat moss give Ocean Forest® its light, aerated texture. Start with Ocean Forest® and watch your plants come alive!
$21.45$20.42
EZ-CLONE 128 Site System Manifold, Black
The new and improved EZ-CLONE Classic Manifold is better than ever. With individually sized manifolds for each system size of the EZ-CLONE Classic Line. Optimal spray coverage is achieved with precise mister placement. Made from highly durable PVC plastic, these manifolds are ultrasonically welded during the manufacturing process to create the strongest bond possible which protects against splitting. Pair these with our EZ-CLONE 360-degree misters for an unrivaled combination. Proprietary design. Molded, durable ABS plastic Creates a thorough and even aeroponic mist Specially designed for each size system (spray nozzles shown in photo are not included) Molded, durable ABS plastic Creates a thorough and even aeroponic mist Specially designed for each size system
$77.48$70.02
You have seen 1440 out of 2679 products